Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

A Nonfullerene Semitransparent Tandem Organic Solar Cell with 10.5% Power Conversion Efficiency

Abstract Semitransparent organic solar cells have great potential for building integrated photovoltaics and power‐generating windows owing to their advantages of light weight, mechanical flexibility, and color tunability. However, the performance of previous semitransparent organic solar cells have been limited by their relatively weak optical absorptions. In this paper, an efficient nonfullerene semitransparent tandem organic solar cell that exhibits a broad absorption from 300 to 1000 nm is reported. The rear subcell is based on a narrow‐bandgap nonfullerene acceptor named IEICS‐4F that exhibits a strong crystallinity and high electron mobility. As a result, the IEICS‐4F‐based single‐junction opaque and semitransparent organic solar cells yield high efficiencies of 10.3% and 7.5%, respectively. To further enhance light harvesting of the single‐junction semitransparent organic solar cells while maintaining a decent transmittance, a semitransparent tandem organic solar cell is fabricated by incorporating a medium‐bandgap P3TEA:FTTB‐PDI 4 blend as the front subcell. A high efficiency of 10.5% is recorded with an average transmittance of 20%.

Chen, Shangshang↗

Silicon Solar Cell Process Development, Fabrication and Analysis

The standard solar cells (2x2 cm) from the cast silicon heatexchanger method) showed a maximum AMO efficiency of 10.1%. Cells from low resistivity material (0.5 ohm-cm) showed lower performance than those of the high resistivity cast silicon (3 ohm-cm), an average efficiency 9.5% versus 7.6% Maximum AMO efficiency of the standard solar cells (2x2 cm) from the EFG (RH) ribbons was about 7.5%. The solar cells from controlled SiC, using the displaced die, showed more consistent and better performance than those of the uncontrolled SiC ribbons, an average efficiency of 6.6% versus 5.4% The average AMO efficiency of the standard silicon ceramic (soc) solar calls were about 6%. These were large area solar cells (an average area of 15 sq cm). A maximum efficiency of 7.3% was obtained. The SOC solar cells showed both leakage and series resistance problems, leading to an average curve fill factor of about 60%.

Yoo, H. I.↗

Non-toxic silver iodide (AgI) quantum dots sensitized solar cells

Highlights: • We have demonstrated AgI sensitized solar cell for the first time. • Obtained mesoporous titania powders possessed small crystallite size, high purity and surface area, and developed mesopores with a narrow pore size distribution. • Photovoltaic measurements revealed the electron injection from AgI to TiO{sub 2}. • The assembled AgI-QD solar cells yielded a power conversion efficiency of 0.64% under one sun illumination. • AgI may be a suitable candidate material for use as a non-toxic sensitizer in QDSSC. - Abstract: The present study reports the performance of a new photosensitizer -AgI quantum dots (QDs)- and mesoporous titania (TiO{sub 2}) nanocrystals synthesized by sol–gel (SG) method for solar cells. Furthermore, the effects of n-heptane on the textural properties of TiO{sub 2} nanocrystals were comprehensively investigated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), N{sub 2} adsorption–desorption measurements, and UV–vis spectroscopy. TiO{sub 2} powders exhibited an anatase-type mesoporous structure with a high surface area of 89.7 m{sup 2}/g. Afterwards, the QDs were grown on mesoporous TiO{sub 2} surface to fabricate a TiO{sub 2}/AgI electrode by a successive ionic layer adsorption and reaction (SILAR) deposition route. Current–voltage characteristics and electrochemical impedance spectroscopy (EIS) data demonstrated that the injection of photoexcited electrons from AgI QDs into the TiO{sub 2} matrix produces photocurrents. The assembled AgI-QD solar cells yielded a power conversion efficiency of 0.64% and a short-circuit current of 2.13 mA/cm{sup 2} under one sun illumination.

36 MATERIALS SCIENCE↗

Contactless Production Testing of Silicon Solar Cells

Critical cost reductions in silicon solar cells are made by minimizing silver usage in their metal contacts. The reason why is both clear and unavoidable—silver is not only expensive, but also a potential limiting resource for scale-up (the PV industry alone used 10.3 % of the global silver supply in 2020 [1]). The result is solar cells with vanishing electrical contact area that are extremely difficult to test prior to module manufacture, when they must be sorted for quality to maximize power output and reliability of the subsequent modules. This project developed a new measurement instrument that enables the transition to solar cells with very low silver content, including cell designs with both minimal busbars and no busbars at all to electrically contact. The resulting instrument at project completion demonstrated the ability to sort cells with comparable—or better—results than existing technology. Compared to existing cell-test instruments, the new tool has minimal contacting requirements, which lowers the maintenance costs and use of consumable parts. We demonstrated innovative, yet pragmatic, solutions for reporting a comprehensive set of measurement results useful for both cell sorting (going forward in the line for module manufacture) and process control (looking backward in the line to identify cell manufacturing issues from wafer to cell-test). In addition to the traditional current-voltage characterization at cell test—short circuit current, open-circuit voltage, power, efficiency and fill factor—the new tool maintains all the advanced parameter characterization of our existing product line such as a substrate doping measurement, carrier recombination (lifetime) analysis, and surface recombination analysis.

14 SOLAR ENERGY↗

Solar cell with silicon oxynitride dielectric layer

Solar cells with silicon oxynitride dielectric layers and methods of forming silicon oxynitride dielectric layers for solar cell fabrication are described. For example, an emitter region of a solar cell includes a portion of a substrate having a back surface opposite a light receiving surface. A silicon oxynitride (SiO.sub.xN.sub.y, 0<x, y) dielectric layer is disposed on the back surface of the portion of the substrate. A semiconductor layer is disposed on the silicon oxynitride dielectric layer.

14 SOLAR ENERGY↗

Third Working Meeting on Gallium Arsenide Solar Cells

Research results are reported for GaAs Schottky barrier solar cells, GaAlAs/GaAs heteroface solar cells, and GaAlAs graded band gap solar cells. Related materials studies are presented. A systems study for GaAs and Si solar concentrator systems is given.

Walker, G. H.↗

A Comparison of CdS and Zn(O,S) Buffer Layers in (Ag,Cu)(In,Ga)Se2 Solar Cells

Cu(In,Ga)Se 2 -based solar cells typically use a C dS buffer layer, even though its relatively low bandgap causes parasitic absorption. While alternatives to CdS have been explored in other studies, limited results have been shown for Ag-alloyed CIGS (ACIGS). In this study, ACIGS solar cells with both CdS and Zn(O,S) buffer layers were fabricated and compared for solar cell performance. The Zn(O,S) buffer slightly improved J sc through reduced absorption, although surface optimization is necessary. The Zn(O,S) ACIGS also had improved FF through reduced series resistance and ideality factor, which could be improved further through optimization. However, the Voc in the Zn(O,S) samples was reduced, likely due to increased bulk and front interface recombination. This study shows the promise of Zn(O,S) as a buffer layer in ACIGS solar cells and suggests pathways for further improvement.

absorption↗

Solar cell with silicon oxynitride dielectric layer

Solar cells with silicon oxynitride dielectric layers and methods of forming silicon oxynitride dielectric layers for solar cell fabrication are described. For example, an emitter region of a solar cell includes a portion of a substrate having a back surface opposite a light receiving surface. A silicon oxynitride (SiOxNy, 0<x, y) dielectric layer is disposed on the back surface of the portion of the substrate. A semiconductor layer is disposed on the silicon oxynitride dielectric layer.

Shepherd, Michael↗

Fullerene surfactants and their use in polymer solar cells

Fullerene surfactant compounds useful as interfacial layer in polymer solar cells to enhance solar cell efficiency. Polymer solar cell including a fullerene surfactant-containing interfacial layer intermediate cathode and active layer.

14 SOLAR ENERGY↗

Realization of GaInP/Si dual-junction solar cells with 29.8% 1-sun efficiency

Combining a Si solar cell with a high-bandgap top cell reduces the thermalization losses in the short wavelength and enables theoretical 1-sun efficiencies far over 30%. We have investigated the fabrication and optimization of Si-based tandem solar cells with 1.8-eV rear-heterojunction GaInP top cells. The III-V and Si heterojunction subcells were fabricated separately and joined by mechanical stacking using electrically insulating optically transparent interlayers. Our GaInP/Si dual-junction solar cells have achieved a certified cumulative 1-sun efficiency of 29.8% ± 0.6% (AM1.5g) in four-terminal operation conditions, which exceeds the record 1-sun efficiencies achieved with both III-V and Si single-junction solar cells. Furthermore, the effect of luminescent coupling between the subcells has been investigated, and optical losses in the solar cell structure have been addressed.

14 SOLAR ENERGY↗

Effect of Dopant Compensation on the Conductivity of the Intrinsic poly-Si Isolation Region in Passivated IBC Silicon Solar Cells

The performance of IBC solar cells depends on the ability of this region to electrically isolate the doped fingers so that shunting does not occur and reduce the cell fill factor. We report on simulations which model the region between the p- and n-type poly-Si fingers of interdigitated back contact (IBC) solar cells as a series of resistors extending from one doped finger to the other. We demonstrate that the existence of a well compensated region between the doped fingers is enough to prevent shunting and loss of cell performance, despite contamination of dopants from the opposing dopant fingers. We show through these simulations that a net doping concentration below ~1018 cm-3 will enable a high resistivity and identify the conditions under which this highly resistive region forms despite imperfect finger edges. Additionally, we apply this analysis to tails measured by time-of-flight secondary ion mass spectrometry and confirm this hypothesis for our experimentally measured tails.

41 EE - Solar Energy Technologies Office (EE-4S)↗

PEDOT:PSS emitters on multicrystalline silicon thin-film absorbers for hybrid solar cells

We fabricated an efficient hybrid solar cell by spin coating poly(3,4-ethylene-dioxythiophene):polystyrenesulfonate (PEDOT:PSS) on planar multicrystalline Si (mc-Si) thin films. The only 5 μm thin Si absorber layers were prepared by diode laser crystallization of amorphous Si deposited by electron beam evaporation on glass. On these absorber layers, we studied the effect of SiO{sub x} and Al{sub 2}O{sub 3} terminated Si surfaces. The short circuit density and power conversion efficiency (PCE) of the mc-Si/Al{sub 2}O{sub 3}/PEDOT:PSS solar cell increase from 20.6 to 25.4 mA/cm{sup 2} and from 7.3% to 10.3%, respectively, as compared to the mc-Si/SiO{sub x}/PEDOT:PSS cell. Al{sub 2}O{sub 3} lowers the interface recombination and improves the adhesion of the polymer film on the hydrophobic mc-Si thin film. Open circuit voltages up to 604 mV were reached. This study demonstrates the highest PCE so far of a hybrid solar cell with a planar thin film Si absorber.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The AMOS cell - An improved metal-semiconductor solar cell

A new fabrication process is being developed which significantly improves the efficiency of metal-semiconductor solar cells. The resultant effect, a marked increase in the open-circuit voltage, is produced by the addition of an interfacial layer oxide on the semiconductor. Cells using gold on n-type gallium arsenide have been made in small areas (0.17 sq cm) with conversion efficiencies of 15% in terrestrial sunlight.

Stirn, R. J.↗

Deuterium-substituted cations enhance perovskite solar cell efficiency and stability

Halide perovskite solar cells with mixed-cation compositions often face instabilities under continuous illumination due to the deprotonation of methylammonium (CH 3 NH 3 + , MA + ) cations. Here, to address this, we systematically evaluate the partial and complete deuteration of MA + cations. This approach inhibits deprotonation and degradation, reduces the formation energy of the perovskite phase, improves grain growth, passivates defects, and restrains ion migration. As a result, perovskite solar cells incorporating this deuteration strategy achieve exceptional performance, including a high fill factor (FF) of 82.6% and a power conversion efficiency (PCE) of 25.6%. Their modules with a device area of 56 cm 2 demonstrate remarkable stability, maintaining over 93.7% of their initial PCE after 1,000 h at the maximum power point under continuous illumination at 40°C. This novel deuteration strategy presents a promising approach to enhance both the efficiency and stability of perovskite solar cells.

14 SOLAR ENERGY↗

Solvent-Mediated Crystallization of CH 3 NH 3 SnI 3 Films for Heterojunction Depleted Perovskite Solar Cells

Organo-lead halide perovskite solar cells have gained enormous significance and have now achieved power conversion efficiencies of ~20%. However, the potential toxicity of lead in these systems raises environmental concerns for widespread deployment. In this work we investigate solvent effects on the crystallization of the lead-free methylammonium tin triiodide (CH 3 NH 3 SnI 3 ) perovskite films in a solution growth process. Highly uniform, pinhole-free perovskite films are obtained from a dimethyl sulfoxide (DMSO) solution via a transitional SnI 2 ·3DMSO intermediate phase. This high-quality perovskite film enables the realization of heterojunction depleted solar cells based on mesoporous TiO 2 layer but in the absence of any hole-transporting material with an unprecedented photocurrent up to 21 mA cm –2 . Charge extraction and transient photovoltage decay measurements reveal high carrier densities in the CH 3 NH 3 SnI 3 perovskite device which are one order of magnitude larger than CH 3 NH 3 PbI 3 -based devices but with comparable recombination lifetimes in both devices. The relatively high background dark carrier density of the Sn-based perovskite is responsible for the lower photovoltaic efficiency in comparison to the Pb-based analogues. These results provide important progress toward achieving improved perovskite morphology control in realizing solution-processed highly efficient lead-free perovskite solar cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimal design of one-dimensional photonic crystal back reflectors for thin-film silicon solar cells

For thin-film silicon solar cells (TFSC), a one-dimensional photonic crystal (1D PC) is a good back reflector (BR) because it increases the total internal reflection at the back surface. We used the plane-wave expansion method and the finite difference time domain (FDTD) algorithm to simulate and analyze the photonic bandgap (PBG), the reflection and the absorption properties of a 1D PC and to further explore the optimal 1D PC design for use in hydrogenated amorphous silicon (a-Si:H) solar cells. With identified refractive index contrast and period thickness, we found that the PBG and the reflection of a 1D PC are strongly influenced by the contrast in bilayer thickness. Additionally, light coupled to the top three periods of the 1D PC and was absorbed if one of the bilayers was absorptive. By decreasing the thickness contrast of the absorptive layer relative to the non-absorptive layer, an average reflectivity of 96.7% was achieved for a 1D PC alternatively stacked with a-Si:H and SiO{sub 2} in five periods. This reflectivity was superior to a distributed Bragg reflector (DBR) structure with 93.5% and an Ag film with 93.4%. n-i-p a-Si:H solar cells with an optimal 1D PC-based BR offer a higher short-circuit current density than those with a DBR-based BR or an AZO/Ag-based BR. These results provide new design rules for photonic structures in TFSC.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Unraveling the Photovoltaic, Mechanical, and Microstructural Properties and Their Correlations in Simple Poly(3‐pentylthiophene) Solar Cells

Abstract The power conversion efficiency of polythiophene organic solar cells is constantly refreshed. Despite the renewed device efficiency, very few efforts have been devoted to understanding how the type of electron acceptor alters the photovoltaic and mechanical properties of these low‐cost solar cells. Herein, the authors conduct a thorough investigation of photovoltaic and mechanical characteristics of a simple yet less‐explored polythiophene, namely poly(3‐pentylthiophene) (P3PT), in three different types of organic solar cells, where ZY‐4Cl, PC 71 BM, and N2200 are employed as three representative acceptors, respectively. Compared with the reference poly(3‐hexylthiophene) (P3HT)‐based solar cells, P3PT‐based devices, all perform more efficiently. Particularly, the P3PT:ZY‐4Cl blend exhibits the highest efficiency (ca. 10%) among the six combinations and outperforms the prior top‐performance system P3HT:ZY‐4Cl. Furthermore, the blend films based on N2200 exhibit a high crack‐onset strain of ∼38% on average, which is approximately 15‐ and 17‐times higher than those of ZY‐4Cl and PC 71 BM, respectively. The microstructural origins for the above difference are well elucidated by detailed grazing incidence X‐ray scattering and microscopy analysis. This work not only underlines the potential of P3PT in prolific solar cell research but also demonstrates the superior tensile properties of polythiophene‐based all‐polymer blends for the preparation of stretchable solar cells.

Polymer Science↗

Cost Trade Between Multi-Junction, Gallium Arsenide, and Silicon Solar Cells

Multi-junction (MJ), gallium arsenide (GaAs), and silicon (Si) solar cells have respective test efficiencies of approximately 24%, 18.5% and 14.8%. Multi-junction and gallium arsenide solar cells weigh more than silicon solar 2 cells and cost approximately five times as much per unit power at the cell level. A trade is performed for the TRMM spacecraft to determine which of these cell types would have offered an overall performance and price advantage to the spacecraft. A trade is also performed for the multi-junction cells under the assumption that they will cost over ten times that of silicon cells at the cell level. The trade shows that the TRMM project, less the cost of the instrument, ground systems and mission operations, would spend approximately $552,000 dollars per kilogram to launch and suppon3science in the case of the spacecraft equipped with silicon solar cells. If these cells are changed out for gallium arsenide solar cells, an additional 31 kilograms of science can be launched and serviced at a price of approximately $90 thousand per kilogram. The weight reduction is shown to derive from the smaller area of the array and hence reductions in the weight of the array substrate and supporting structure. ff the silicon solar cells are changed out for multi-junction solar cells, an additional 45 kilograms of science above the silicon base line can be launched and supported at a price of approximately $58,000 per kilogram. The trade shows that even if the multi-junction cells are priced over ten times that of silicon cells, a price that is much higher than projected, that the additional 45 kilograms of science are launched and serviced at $180,000 per kilogram. This is still much less than the original $552,000 per kilogram to launch and service the science. Data and qualitative factors are presented to show that these figures are subject to a great deal of uncertainty. Nonetheless, the benefit of the higher efficiency solar cells for TRMM is far greater than the uncertainties in the analysis.

Gaddy, Edward M.↗