Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STORED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

TANK FARM RETRIEVAL LESSONS LEARNED AT THE HANFORD SITE

One of the environmental remediation challenges facing the nation is the retrieval and permanent disposal of approximately 90 million gallons of radioactive waste stored in underground tanks at the U. S. Department of Energy (DOE) facilities. The Hanford Site is located in southeastern Washington State and stores roughly 60 percent of this waste. An estimated 53 million gallons of high-level, transuranic, and low-level radioactive waste is stored underground in 149 single-shell tanks (SSTs) and 28 newer double-shell tanks (DSTs) at the Hanford Site. These SSTs range in size from 55,000 gallons to 1,000,000 gallon capacity. Approximately 30 million gallons of this waste is stored in SSTs. The SSTs were constructed between 1943 and 1964 and all have exceeded the nominal 20-year design life. Sixty-seven SSTs are known or suspected to have leaked an estimated 1,000,000 gallons of waste to the surrounding soil. The risk of additional SST leakage has been greatly reduced by removing more than 3 million gallons of interstitial liquids and supernatant and transferring this waste to the DST system. Retrieval of SST saltcake and sludge waste is underway to further reduce risks and stage feed materials for the Hanford Site Waste Treatment Plant. Regulatory requirements for SST waste retrieval and tank farm closure are established in the Hanford Federal Facility Agreement and Consent Order (HFFACO), better known as the TriParty Agreement, or TPA. The HFFACO was signed by the DOE, the State of Washington Department of Ecology (Ecology), and U. S. Environmental Protection Agency (EPA) and requires retrieval of as much waste as technically possible, with waste residues not to exceed 360 fe in 530,000 gallon or larger tanks; 30 fe in 55,000 gallon or smaller tanks; or the limit of waste retrieval technology, whichever is less. If residual waste volume requirements cannot be achieved, then HFFACO Appendix H provisions can be invoked to request Ecology and EPA approval of an exception to the waste retrieval criteria for a specific tank. Tank waste retrieval has been conducted at the Hanford Site over the last few decades using a method referred to as Past Practice Hydraulic Sluicing. Past Practice Hydraulic Sluicing employs large volumes of DST supernatant and water to dislodge, dissolve, mobilize, and retrieve tank waste. Concern over the leak integrity of SSTs resulted in the need for tank waste retrieval methods capable of using smaller volumes of liquid in a more controlled manner.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

PEP-II Status

PEP-II and BaBar have just finished run 7, the last run of the SLAC B-factory. PEP-II was one of the few high-current e+e- colliding accelerators and holds the present world record for stored electrons and stored positrons. It has stored 2.07 A of electrons, nearly 3 times the design current of 0.75 A and it has stored 3.21 A of positrons, 1.5 times more than the design current of 2.14 A. High-current beams require careful design of several systems. The feedback systems that control instabilities, the RF system stability loops, and especially the vacuum systems have to handle the higher power demands. We present here some of the accomplishments of the PEP-II accelerator and some of the problems we encountered while running high-current beams.

43 PARTICLE ACCELERATORS↗

Optimization of Integrated Luminosity of the Fermilab Tevatron Collider

We present the strategy which has been used recently to optimize integrated luminosity at the Fermilab Tevatron proton-antiproton collider. We use a relatively simple model where we keep the proton intensity fixed, use parameters from fits to the luminosity decay of recent stores as a function of initial antiproton intensity (stash size), and vary the stash size to optimize the integrated luminosity per week. The model assumes a fixed rate of antiproton production, that a store is terminated as soon as the target stash size for the next store is reached, and that the only downtime is due to store turn-around time. An optimal range of stash sizes is predicted. Since the start of Tevatron operations based on this procedure, we have seen an improvement of approximately 35% in integrated luminosity. Other recent operational improvements have been achieved by decreasing the shot-setup time and by reducing beam-beam effects by making the proton and antiproton brightnesses more compatible, for example by scraping protons to smaller emittances.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Robust control of the current profile and plasma energy in EAST

Integrated control of the toroidal current density profile, or alternatively the q-profile, and plasma stored energy is essential to achieve advanced plasma scenarios characterized by high plasma confinement, magnetohydrodynamics stability, and noninductively driven plasma current. The q-profile evolution is closely related to the evolution of the poloidal magnetic flux profile, whose dynamics is modeled by a nonlinear partial differential equation (PDE) referred to as the magnetic-flux diffusion equation (MDE). The MDE prediction depends heavily on the chosen models for the electron temperature, plasma resistivity, and non-inductive current drives. To aid control synthesis, control-oriented models for these plasma quantities are necessary to make the problem tractable. However, a relatively large deviation between the predictions by these control-oriented models and experimental data is not uncommon. For this reason, the electron temperature, plasma resistivity, and non-inductive current drives are modeled for control synthesis in this work as the product of an “uncertain” reference profile and a nonlinear function of the different auxiliary heating and current-drive (H&CD) source powers and the total plasma current. The uncertainties are quantified in such a way that the family of models arising from the modeling process is able to capture the q-profile and plasma stored energy dynamics from a typical EAST shot. A control-oriented nonlinear PDE model is developed by combining the MDE with the “uncertain” models for the electron temperature, plasma resistivity, and non-inductive current drives. This model is then rewritten into a control framework to design a controller that is robust against the modeled uncertainties. The resulting controller utilizes EAST's H&CD powers and total plasma current to regulate the q profile and plasma stored energy even when mismatches between modeled and actual dynamics are present. The effectiveness of the controller is demonstrated through nonlinear simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Growth kinetics of Al–Fe intermetallic compounds during annealing treatment of friction stir lap welds

In this study, we explored the growth kinetics of the Al–Fe intermetallic (IM) layer at the joint interface of the St-12/Al-5083 friction stir lap welds during post-weld annealing treatment at 350, 400 and 450 °C for 30 to 180 min. Optical microscope (OM), field emission gun scanning electron microscope (FEG-SEM) and transmission electron microscope (TEM) were employed to investigate the structure of the weld zone. The thickness and composition of the IM layers were evaluated using image analysis system and electron back-scatter diffraction (EBSD), respectively. Moreover, kernel average misorientation (KAM) analysis was performed to evaluate the level of stored energy in the as-welded state. The results showed that the growth kinetics of the IM layer was not governed by a parabolic diffusion law. Presence of the IM compounds as well as high stored energy near the joint interface of the as-welded sample was recognized to be the origin of the observed deviation from the parabolic diffusion law. - Highlights: • This work provided a new insight into growth kinetics of Al–Fe IM thickness. • The growth kinetics of IM layer was not governed by a parabolic diffusion law. • IM near the joint interface was the origin of deviation from the parabolic law. • High stored energy at joint interface was origin of deviation from parabolic law.

36 MATERIALS SCIENCE↗

Microstructure characterization based on the type of deformed grains in cold-rolled, Cu-added, bake-hardenable steel

The electron backscatter diffraction technique has been used to characterize the microstructure of deformed grains in cold-rolled, Cu-added, bake-hardenable steel. A new scheme based on the kind and number of average orientations, as determined from a unique grain map of the deformed grains, was developed in order to classify deformed grains by type. The α-fiber components, γ-fiber components and random orientations, those which could not be assigned to either γ-fiber or α-fiber components, were used to define the average orientation of unique grains within individual deformed grains. The microstructures of deformed grains in as-rolled specimens were analyzed based on the Taylor factor, stored energy, and misorientation. The relative levels and distributions of the Taylor factor, the stored energy and the misorientation were examined in terms of the types of deformed grains. - Highlights: • We characterized the microstructure of Cu-added BH steel using EBSD. • A new scheme was developed in order to classify deformed grains by type. • Stored energy and misorientation are strongly dependent on the type of deformed grains. • Microstructure was examined in terms of the types of deformed grains.

36 MATERIALS SCIENCE↗

Quantifying the inter- and intra-granular stresses and their effects on deformation behaviors for the polycrystalline hexagonal beryllium by neutron diffraction

Highlights: • The inter- and intra-granular stresses are quantified for the polycrystalline hexagonal metal beryllium. • Composite behavior of the internal stresses is revealed in the polycrystalline beryllium. • Those internal stresses show the obvious grain-orientation dependence. • Those stresses can be significantly tuned by the temperature and strain rate effects. • The dislocation slip and twinning are quantified together with the inter- and intra-granular stored energies. - Abstract: The internal stresses developing at different length scales play the important role in materials performance. This importance has been well recognized for the cubic metals, however, not for the hexagonal close-packed (hcp) ones. The present work investigates the intergranular and intragranular stresses in the polycrystalline hexagonal beryllium by neutron diffraction. The correlation between those internal stresses and the deformation mechanism is revealed, and the strain rate and temperature effects on those stresses are presented. A composite behavior of intergranular and intragranular stresses is observed, which can be significantly tuned by the temperature and strain rate effects. The intergranular stress and stored energy are large for the soft-oriented grains (SOGs), while the intragranular stress and stored energy are large for the hard-oriented ones (HOGs). Both of those stresses are significantly high for the dynamic strain rate while they are relatively low for the elevated temperature. The large internal stresses in the dynamically compressed specimen should be attributed to the large number of twins and high density of dislocations. Different HOGs-SOGs configurations are proposed on the light of those observations, which might facilitate the properties controlling and extend the application scope for the hcp metal beryllium.

36 MATERIALS SCIENCE↗

Integration of a Wigner effect-based energy storage system with an advanced nuclear reactor

In this work, an innovative energy storage concept based on the purposeful creation of defects in crystalline material by neutron irradiation is presented. Lattice defects are generated when heavy particles collide with the atoms in a crystal structure, i.e., if the incoming particles have enough energy, recoil atoms are displaced from their initial lattice sites. Most of the displaced atoms will eventually combine with nearby vacancies, but some of them will come to rest in non-ideal locations. The energy held by displaced atoms is called Wigner energy. Lattice defects can migrate and form clusters, and the Wigner energy can be released from these groupings if sufficient activation energy is provided. In the nuclear industry, this effect is well-known since it represented an issue for graphite-moderated reactors. This work presents the conceptual design of an engineering system that exploits this physical process to store the energy of neutrons in advanced reactor concepts. In the first part of the paper, the theoretical performance of an energy storage system based on the Wigner effect is described. Given the lattice properties and the compatibility with the harsh reactor environment, graphite was selected as the candidate material for the irradiation targets. Both experimental data and molecular dynamics simulations confirmed that this system can achieve performance comparable with state-of-the-art batteries in terms of stored energy density. In the second part of the paper, the engineering challenges of this innovative technology and the proposed solutions are described. After defining the optimal irradiation conditions, the different steps of the operation of the proposed energy system (from energy storing to energy harvesting) were defined. Finally, the integration of this concept with advanced reactor designs, i.e., a Sodium-cooled Fast Reactor and a Molten Salt-cooled Reactor, was investigated and the corresponding performance was evaluated.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Improvement in the statistical operation of a Blumlein pulse forming line in bipolar pulse mode

The paper presents the results of studies on shot-to-shot performance of a water Blumlein pulse forming line of 1–1.2 kJ of stored energy. The experiments were carried using the TEMP-4M pulsed ion beam accelerator during its operation in both unipolar pulse mode (150 ns, 250–300 kV) and bipolar-pulse mode with the first negative (300–600 ns, 100–150 kV) followed by a second positive (120 ns, 250–300 kV) pulse. The analysis was carried out for two cases when the Blumlein was terminated with a resistive load and with a self-magnetically insulated ion diode. It was found that in bipolar pulse mode the shot-to-shot variation in breakdown voltage of a preliminary spark gap is small, the standard deviation (1σ) does not exceed 2%. At the same time, the shot-to-shot variation in the breakdown voltage of the main spark gap in both bipolar-pulse and unipolar pulse mode is 3–4 times higher than that for the preliminary spark gap. To improve the statistical performance of the main spark gap we changed the regime of its operation from a self-triggered mode to an externally triggered mode. In the new arrangement the first voltage pulse at the output of Blumlein was used to trigger the main spark gap. The new trigatron-type regime of the main spark gap operation showed a good stability of breakdown voltage and thus allowed to stabilize the duration of the first pulse. The standard deviation of the breakdown voltage and duration of the first pulse did not exceed 2% for a set of 50 pulses. The externally triggered mode of the main gap operation also allowed for a decrease in the charging voltage of the Blumlein to a 0.9–0.95 of self-breakdown voltage of the main spark gap while the energy stored in Marx generator was decreased from 4 kJ to 2.5 kJ. At the same time the energy stored in Blumlein remained the same.

43 PARTICLE ACCELERATORS↗

Space-time evolution of ejected plasma for the triggering of gas switch

Ejected plasma has been widely applied to the discharge process of gas spark switches as a trigger technology, and the development process of ejected plasma has a direct and important effect on the discharge characteristics of gas switches. In this paper, both the injection characteristics and space-time evolution of ejected plasma for the triggering of gas spark switch with different stored energies, pulse polarities, and pressures are studied. The discharge characteristics and breakdown process of a gas switch ignited by ejected plasma under different working coefficients are also discussed briefly. The results show that stored energy has significant influence on the characteristics of ejected plasma. With the increase of stored energy, the propulsion mode of ejected plasma in the axial direction transforms from “plasmoid” to “plasma flow,” and the distribution of the ejected plasma goes through “cloud,” “core-cloud,” and “branch” in sequence. The velocity of ejected plasma under negative pulse polarity is obviously higher than that under positive pulse polarity, especially at the very beginning time. The radial dimensions of ejected plasma under two kinds of pulse polarities follow the similar varying pattern over time, which increase first and then decrease, assuming an inverted “U”-shaped curve. With the increase of pressure, the velocity of ejected plasma significantly decreases and the “branch” channels droop earlier. Applying the ejected plasma to the triggering of a gas switch, the switch can be triggered reliably in a much wide working coefficient range of 10%–90%. With the increase of working coefficient, the breakdown process of the switch translates from slow working mode to fast working mode, and the delay time reduces from tens of μs to hundreds of ns.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermochemical Heat Storage for Concentrated Solar Power: Thermochemical System Reactor Design for Thermal Energy Storage

Thermal energy storage (TES) is an integral part of a concentrated solar power (CSP) system. It enables plant operator to generate electricity beyond on sun hours and supply power to the grid to meet peak demand. Current CSP sensible heat storage systems employ molten salts as both the heat transfer fluid and the heat storage media. These systems have an upper operating tempera ture limit of around 400°C. Future TES systems are expected to operate at temperatures between 600°C–1000°C for higher thermal efficiencies which should result in lower electricity cost. To meet future operating temperature and electricity cost requirements, a TES concept utilizing thermochemical cycles (TCs) based on multivalent solid oxides was proposed. The system employs a pair of reduction and oxidation (REDOX) reactions to store and release heat. In the storage step, hot air from the solar receiver is used to reduce the oxidation state of an oxide cation, e.g. Fe 3+ to Fe 2+ . Heat energy is thus stored as chemical bonds and the oxide is “charged”. To discharge the stored energy, the reduced oxide is re-oxidized in air and heat is released. Air is used as both the heat transfer fluid and reactant and no storage of fluid is needed. This project investigated the engineering and economic feasibility of this proposed TES concept. The DOE storage cost and LCOE targets are $\$$15/kWh and $\$$0.09/kWh respectively. Sixteen pure oxides cycles were identified through thermodynamics calculations and literature information. Data showed the kinetics of re-oxidation of the various oxides to be a key barrier to implementing the proposed concept. A down selection was carried out based on operating temperature, materials costs and preliminary laboratory measurements. Cobalt oxide, manganese oxide and barium oxide were selected for developmental studies to improve their REDOX reaction kinetics. A novel approach utilizing mixed oxides to improve the REDOX kinetics of the selected oxides was proposed. It partially replaces some of the primary oxide cations with selected secondary cations. This causes a lattice charge imbalance and increases the anion vacancy density. Such vacancies enhance the ionic mass transport and lead to faster re-oxidation. Re oxidation fraction of Mn 3 O 4 → Mn 2 O 3 and CoO → Co 3 O 4 was improved by up to 16 fold through the addition of a secondary oxide. However, no improvement was obtained in barium based mixed oxides. In addition to enhancing the short term re-oxidation kinetics, it was found that the use of mixed oxides also help to stabilize or even improve the TES properties after long term thermal cycling. Part of this improvement could be attributed to a reduced grain size in the mixed oxides. Based on the measurement results, manganese-iron, cobalt-aluminum and cobalt iron mixed oxides have been proposed for future engineering scale demonstration. Using the cobalt and manganese mixed oxides, we were able to demonstrate charge and discharge of the TES media in both a bench top fixed bed and a rotary kiln-moving bed reactor.

14 SOLAR ENERGY↗

Hosting Hyrax in the Cloud While Preserving the User Experience

Cloud object stores enable data providers to reduce costs and provide uniform data servers across organizational divisions. This talk will address how new capabilities provided by cloud computing can be used with existing software so that users get the benefits provided by cloud technology (access to data at lower cost, e.g.) without disrupting their existing workflow(s). We will address ways to reduce response latency often associated with Cloud object stores and ways to simulate the hierarchy of a POSIX file system using a key-value object store. This work is based an on-going NASA EED2 project to enhance the Hyrax data server for operation in the Amazon Web Services Cloud.

Hyrax server↗

The real mission of ITER

For future machines, the plasma stored energy is going up by factors of 20-40x, and plasma currents by 2-3x, while the surface to volume ratio is at the same time decreasing. Therefore the disruption forces, even for constant B, (which scale like IxB), and associated possible localized heating on machine components, are more severe. Notably, Tore Supra has demonstrated removal of more than 1 GJ of input energy, over nearly a 400 second period. However, the instantaneous stored energy in the Tore Supra system (which is most directly related to the potential for disruption damage) is quite small compared to other large tokamaks. The goal of ITER is routinely described as studying DT burning plasmas with a Q {approx} 10. In reality, ITER has a much more important first order mission. In fact, if it fails at this mission, the consequences are that ITER will never get to the eventual stated purpose of studying a burning plasma. The real mission of ITER is to study (and demonstrate successfully) plasma control with {approx}10-17 MA toroidal currents and {approx}100-400 MJ plasma stored energy levels in long-pulse scenarios. Before DT operation is ever given a go-ahead in ITER, the reality is that ITER must demonstrate routine and reliable control of high energy hydrogen (and deuterium) plasmas. The difficulty is that ITER must simultaneously deal with several technical problems: (1) heat removal at the plasma/wall interface, (2) protection of the wall components from off-normal events, and (3) generation of dust/redeposition of first wall materials. All previous tokamaks have encountered hundred's of major disruptions in the course of their operation. The consequences of a few MA of runaway electrons (at 20-50 MeV) being generated in ITER, and then being lost to the walls are simply catastrophic. They will not be deposited globally, but will drift out (up, down, whatever, depending on control system), and impact internal structures, unless 'ameliorated'. Basically, this represents an extraordinarily robust e-beam welding machine, capable of deep penetration into any armor tiles, to the cooling channels which are embedded less than 1 cm below the tile surface. When energy is deposited in a fraction of a second on (or in) a tile, the presence of underlying water cooling does no good for the purposes of heat removal.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evaluating the long-term hydrology of an evapotranspiration-capillary barrier with a 1000 year design life

A surface barrier (or cover) is a commonly used technology for subsurface remediation. A key function of the barrier is to reduce or eliminate the movement of meteoric precipitation into the underlying waste zone, where it could mobilize and transport contaminants. Surface barriers are expected to perform for centuries to millennia, yet there are very few examples of performance for periods longer than a decade. The Prototype Hanford Barrier was constructed in 1994 over an existing waste site to demonstrate its long-term performance for a design period of 1000 years. This barrier is a field-scale evapotranspiration-capillary (ETC) barrier. In this design, the storage layer consists of 2-m-thick silt loam. The 19-year monitoring results show that the store-and-release mechanism for the ETC barrier worked efficiently as the storage layer was recharged in the winter season (November to March) and the stored water was released to the atmosphere in the summer season (April to October) via soil evaporation and plant transpiration. The capillary break functioned normally in improving the storage capacity and minimizing drainage. The maximum drainage observed through the ET barrier at any of the monitoring stations was only 0.178 mm yr -1 (under an enhanced precipitation condition), which is less than the design criterion. A very small amount (2.0 mm yr -1 on average) of runoff was observed during the 19-year monitoring period. The observed storage capacity of the storage layer was considerably (39%) larger than the estimated value based on the method of equilibrium of water pressure. After a controlled fire in 2008, the newly grown vegetation (primarily shallow-rooted grasses) could still release the stored water and summer precipitation to the atmosphere via transpiration. The findings are useful for predicting water storage and ET under different precipitation conditions and for the design of future barriers.

58 GEOSCIENCES↗

Simulation study of chemo-mechanical impacts of CO 2 injection in morrow b sandstone reservoir

Here, this study investigates the impacts of geomechanical and geochemical changes on carbon storage in a partially depleted oil reservoir, using results from four different coupled simulation models. Models were used to examine the relative importance of storage mechanisms, and how changing reservoir parameters might affect these mechanisms through time. The study uses data from a Morrowan sandstone reservoir in the Farnsworth Unit (FWU), Ochiltree County, Texas which is currently undergoing CO 2 enhanced oil recovery (EOR). Partially depleted oil reservoirs such as the FWU offer attractive carbon utilization and/or storage targets because of existing infrastructure and economic benefits from incremental oil recovery as well as tax credits. However, prediction of storage capacity or long-term fluid migration in these fields can be difficult because of the wide variation in formation fluids and operational histories that may have undergone. CO 2 injection can cause complex geomechanical and geochemical responses in a reservoir as a result of interplay between dynamic changes in pore pressure, reservoir temperature, fluid composition, and interactions between formation fluids, CO 2 , and reservoir rock. Thus, multiple coupled numerical simulation models must be developed and used to more precisely understand what CO 2 storage mechanisms are most significant, as well as the long-term fate of the stored CO 2 . Our study used results from hydrodynamic, coupled hydro-geomechanical, coupled hydro-geochemical, and coupled hydro-geomechanical-geochemical models to examine how changes in geomechanical and geochemical properties can impact the injectivity or storage capacity of CO 2 . Models simulated historical field operations and then forward-modeled a water-alternate-gas (WAG) operation for 20 years, followed by a 1000-year post-injection monitoring. The work demonstrates that in this specific reservoir, geomechanical impacts appear to be more significant than any geochemical processes, which showed minimal impact on reservoir properties. Furthermore, these simulation scenarios corroborated other studies showing more than 90% of CO 2 injected are being stored and will remain stored in the reservoir. The study was able to draw on a rich set of data from this currently operational project for the work. Because the Morrow is a widespread oil-bearing reservoir in the midcontinent of the United States and is fairly typical of many sandstone reservoirs elsewhere, the study has significance beyond the boundaries of our field area.

58 GEOSCIENCES↗

Carbon Storage in Fold‐and‐Thrust Belts: An Overlooked Gigatonne Storage Opportunity

This study presents numerical investigations of the trapping characteristics of fold-and-thrust belt structures, defining three carbon capture and storage (CCS) play types that could be used to store commercial volumes (millions of tonnes) of CO 2 . Specifically, we present simulations of CO 2 storage in three fold-and-thrust belt models comprising a thrust-ramp, duplex, and thrust-fold geometry. To constrain these play types in realistic geology, each model is based on a study site, including a novel investigation of a greenfield saline reservoir in Virginia, USA, being considered for commercial carbon storage and two well-characterized petroleum fields: the Wilburton field in Oklahoma, USA, and the Incahuasi field in Bolivia. Our results provide insight into several key parameters, such as the long-term security of injected CO 2 in these geologies and injection strategies for maximizing storage efficiency while reducing pressure-related risk. These results improve the understanding of CCS in fold-and-thrust belt storage sites globally by describing general storage parameters that may be applied to site-specific projects. We find that thrust-ramp geometries may securely trap CO 2 through solubility and hydrodynamic trapping under suitable reservoir conditions, duplex structures may store some quantities of CO 2 but are pressure-constrained, and that thrust-ramp structures may store large quantities of CO 2 by maximizing fetch volume, which simultaneously lowers geomechanical risk by reducing pressure buildup along zones of weakness.

42 ENGINEERING↗

Climatic controls on soil and saprock nitrogen distribution and persistence in the Sierra Nevada

Nitrogen (N) is an essential nutrient in soil that regulates plant growth, terrestrial sequestration of atmospheric carbon dioxide, and persistence of organic compounds. However, major knowledge gaps remain about how climate change may impact N accumulation and persistence, especially in deep soil and saprock (friable weakly weathered bedrock). Our objective was to understand how climate impacts the accumulation of N in soil and saprock and how climate impacts soil N distribution, persistence, and mechanisms of N persistence. We investigated N concentration in bulk soil and density fractions. We estimated N persistence along a bio-climatic sequence—sites range from a low-elevation oak savannah, mid-elevation pine-oak/mixed-conifer forest, to a high-elevation subalpine forest—in the southern Sierra Nevada in California. A combination of radiocarbon and elemental composition measurements along with a first-order kinetic model was used. The N concentration in the bulk soil and density fractions declined with depth, and there was a relatively greater mineral-associated heavy fraction (HF) N in deeper samples. The cooler/wetter mixed conifer site held 37% of profile N in saprock, which was greater than that of the entire soil profile at the drier/hotter oak savannah. The majority of N in soil, which was in the HF, was not influenced by climate proxies tested. However, both unprotected and occluded fractions of N were strongly influenced by climate. Soil N mean residence time (MRT) showed that drier/hotter climates have a shorter MRT, compared to mid-elevation sites with cooler/wetter climates. The effect of climate on deep saprock N storage might be indirect, primarily through climatic influence on the thickness of saprock. Overall, our findings suggest the mineral-associated HF N pool will not be vulnerable to changes in climate and will continue to contribute to the persistent soil N pool. The amount of topsoil and subsoil unprotected and occluded N can be explained by gross primary productivity and mean annual precipitation indicating that changes in climate can influence N partitioning. N stored in deep soil and saprock may be less vulnerable to climate than N stored in drier/hotter climates with less deeply stored N. It is critical to dig deeper to understand terrestrial ecosystems’ response to climate.

58 GEOSCIENCES↗

Effects of moisture and aging upon decomposition of methyl iodide by reduced silver mordenite

Abstract Reduced silver mordenite has been considered as a sorbent for the capture of organic iodides, especially methyl iodide, from off-gases produced by aqueous used nuclear fuel reprocessing operations. The adsorption capacity of this material has been unpredictable especially when NO x and water are present. Previous work has found that a catalytic decomposition reaction is occurring on the surface but few determinations have been made of the kinetics of this reaction. The work presented tested the adsorption behavior and apparent catalytic reaction rate in humid conditions and compared those to dry conditions testing. Both experiments observed a first order reaction with rate constants of 0.0847 L/g sorbent/s and 0.1202 L/g sorbent/s respectively. Such a reduction in apparent rate constant is possibly due to either water obstructing methyl iodide adsorption or product desorption limitation. Changes in the adsorption profile were also apparent between these two, with the humid conditions experiment reaching saturation sooner than the dry conditions experiment. Additionally, an experiment into the effects of sorbent storage in a controlled laboratory environment was performed. The performance of the sorbent materials that were stored with silver in the zerovalent state was slightly inferior to those materials that were stored in ionic form (Ag + ) and reduced to zerovalent silver immediately prior to subjecting them to sorption test. The materials stored with silver in the ionic form (and reduced just prior to application) behaved essentially similarly to the freshly synthesized (and reduced) sorbents in the sorption tests. This suggests that zerovalent silver experiences some oxidation resulting in deactivation of some sites.

Goettsche, Heinrik↗