Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Reading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Noise Erasure in Quantum-Limited Current Amplifiers

Superconducting quantum interference devices (SQUIDs) are extraordinarily sensitive to magnetic flux and thus make excellent current amplifiers for cryogenic applications. One such application of high interest to Sandia is the set-up and state read-out of quantum dot based qubits, where a qubit state is read out from a short current pulse (microseconds to milliseconds long) of approximately 100 pA, a signal that is easily corrupted by noise in the environment. A Parametric SQUID Amplifier can be high bandwidth (in the GHz range), low power dissipation (less than 1pW), and can be easily incorporated into multi-qubit systems. In this SAIL LDRD, we will characterize the noise performance of the parametric amplifier front end -- the SQUID -- in an architecture specific to current readout for spin qubits. Noise is a key metric in amplification, and identifying noise sources will allow us to optimize the system to reduce its effects, resulting in higher fidelity readout. This effort represents a critical step in creating the building blocks of a high speed, low power, parametric SQUID current amplifier that will be needed in the near term as quantum systems with many qubits begin to come on line in the next few years.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Processing Meteorological Data for the CAP-88 PC Model at Los Alamos National Laboratory

The Environmental Protection and Compliance-Compliance Programs (EPC-CP) group at Los Alamos National Laboratory (LANL) uses the Clean Air Act Assessment Package 1988 (CAP-88, Littleton 2020) PC model (Version 4.1) to estimate radiological doses for a set of areal sectors surrounding a release location, in order to satisfy the Environmental Protection Agency (EPA) National Emission Standards for Hazardous Air Pollutants (NESHAP) dose calculation requirement in 40 CFR 61 Subpart H. Among several types of data that must be prepared for CAP-88 input is a text file of meteorological data (“WIND” file), consisting of the joint frequency of wind direction, wind speed, and atmospheric stability categories. EPC-CP produces customized WIND files by running a CAP-88 utility program on a user generated text file of wind data in a different format, known as a STability ARray (STAR) file (Turner, 1964). At LANL, EPC-CP meteorologists prepare customized STAR files with data over desired time periods at selected meteorological towers. A custom program written in Precision Visuals -Workstation Analysis and Visualization Environment (PV-WAVE), a commercial Fortran-like language, is used to read LANL meteorological data and write a STAR file; the executable filename is “Star.out”. However, the outdated PV-WAVE utility program is being phased out by EPC-CP, due to the inefficient process to run it and an inability to modify the code. To preserve the ability to create customized meteorological data for CAP-88 in a way that will be easy to use and maintain, a new replacement utility program, written in the Python programming language, has been developed. The new, improved program reads a data file from any LANL meteorological tower, and at each desired observation time, determines the wind direction, wind speed, and stability categories defined in the CAP-88 documentation. The frequencies of all combinations of the three sets of categories are calculated and written to a file in the STAR format, which can later be converted to a WIND file for input into CAP-88.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Results from Accelerated Environmental Testing of Barcoded Identifiers for UF 6 Cylinders

This report provides the qualitative and quantitative results from the accelerated environmental testing campaign. A total of 444 samples were subjected to 10 tests that included UV, salt fog, temperature, blowing dust, high pressure and temperature water, and impact exposure. Each sample included a two-dimensional barcode and an alphanumeric string representing the cylinder identification number. When evaluating the results, primary attention was placed on the decodability of the barcodes using a barcode verifier device, since machine scanning a barcode offers the greatest efficiency and accuracy gains when reading cylinder identification numbers during safeguards activities. Contrast was considered the critical test parameter because maintaining contrast under a wide range of environmental conditions is of fundamental importance to decoding the identification number of the barcodes. Additionally, manual readability of the alphanumeric string was considered an important factor in determining whether an inspector or operator could still read the identification number of the cylinder if the barcode proved to be undecodable.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Reconstruction of the Room D, B, G, and Q Closure Histories at the Waste Isolation Pilot Plant

Experimental measurements of room closure in salt repositories are valuable for understanding the evolution of the underground and for validating geomechanical models. Room closure was measured during a number of experiments at the Waste Isolation Pilot Plant (WIPP) during the 1980's and 1990's. Most rooms were excavated using a multi-pass mining sequence, where each pass necessarily destroyed some of the mining sequence closure measurement points. These destroyed points were promptly reinstalled to capture the closure after the mining pass. After the room was complete, the mining sequence closure measurement stations were supplemented with remotely read closure measurement stations. Although many aspects of these experiments were thoroughly documented, the digital copies of the closure data were inadvertently destroyed, the non-trivial process of zeroing and shifting the raw closure measurements after each mining pass was not precisely described, the various closure measurements within a given room were not directly compared on the same plot, and the measurements were collected for several years longer than previously reported. Consequently, the hand-written mining sequence closure measurements for Rooms D, B, G, and Q were located in the WIPP archives, digitized, and reanalyzed for this report. The process of reconstructing the mining sequence closure histories was documented in detail and the raw data can be found in the appendices. Within the mid-section of a given room, the reconstructed closure histories were largely consistent with other mining sequence and remotely read closure histories, which builds confidence in the experiments and suggests that plane strain is an appropriate modeling assumption. The reconstructed closure histories were also reasonably consistent with previously published results, except in one notable case: the reconstructed Room Q closure histories 30 days after excavation were about 45 % less than the corresponding closures reported in Munson's 1997 capstone paper.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Embedding Sensors in 3D Printed Metal Structures

The Transformational Challenge Reactor (TCR) program is leveraging recent advances in modeling and simulation, materials, and additive manufacturing (AM) technologies to design a modern nuclear reactor. Some of the main TCR technologies include in situ monitoring and the integration of sensors during the manufacturing of quality-significant nuclear reactor components. This report describes the general procedure and process optimization for embedding sensors within generic stainless steel 316 (SS316) components using laser powder bed fusion (LPBF). A more detailed, quality-significant test plan and supporting procedures are available upon request (ORNL/TM-2021/2127). LPBF involves the use of a scanning laser to selectively melt regions of a powder bed, additively building a part layer by layer. This report describes the LPBF processing technique and discusses the effects of LPBF processing parameters on the success of the sensor embedding process. Experiments used machined cavities in the form of channels in an SS316 base for the sensors to lay in while material is additively built over the top, thereby embedding them in an SS316 matrix. A preliminary investigation involved using empty SS316 sheaths as surrogates to explore the effects of various LPBF processing parameters and the dimensional requirements of the machined channels. Microstructural investigations showed that a smaller channel width/depth combination closer to the sensor’s diameter was best for the embedding process. After the desired parameters were selected, Type-K thermocouples were embedded and evaluated post-embedding using nondestructive thermal testing, as well as destructive sectioning and microscopy. Post-build characterization showed that the thermocouples were well-bonded to the SS316 matrix and were fully functional after embedding. During thermal testing to temperatures up to 500 °C, the embedded thermocouples read consistently with one another and deviated only slightly from the readings of a nonembedded thermocouple located within the furnace. This slight discrepancy was most likely due to differences in the thermal time constants for a nonembedded thermocouple vs. a thermocouple embedded in a solid SS316 block. The results presented in this report will serve as the foundation for future work that will focus on embedding sensors in relevant TCR reactor components and eventually testing those components under neutron irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

PV Reference Cells for Outdoor Use: An Investigation of Calibration Factors

Reference cells are widely used in the photovoltaic (PV) industry to measure irradiance. For field applications and outdoor use, a variety of products are on the market, and they are often perceived as a low-cost alternative to thermopile radiometers. But reference cell characteristics differ substantially from the latter, therefore measurements made by one category of instrument cannot be substituted for or directly compared with the other. The National Renewable Energy Laboratory's (NREL's) Solar Radiation Research Laboratory is currently in a multiyear effort to develop guidance and recommendations for the design and use of outdoor reference cells, with a view to reducing inconsistencies and measurement uncertainty. The core of this effort is the long-term deployment of 39 units of 10 distinct types made by 6 manufacturers. This report compares the calibration factors provided by manufacturers - which most users rely upon - to those measured at a high level of accuracy by NREL's Cell Lab. It also reports on the application of the Broadband Outdoor Radiometer Calibration (BORCAL) method to reference cells. As a group, the factory calibrations for the crystalline silicon cells showed a small positive bias of +0.7%, with a tight distribution around this value. This is a very good result for the manufacturers. The two World Photovoltaic Scale cells constituted outliers, with a mean deviation of -0.8%, which is still within the reported uncertainty ranges. The data collected during the BORCAL procedures show a strong and systematic fluctuation of the apparent responsivity of the reference cells over the course of a day, which was anticipated. Consequently, the standard BORCAL R@45 calibration factors underestimated the reference cell responsivities by 1%-4%. An alternate responsivity indicator was developed, R'@30, incorporating adjustments for temperature response, spectral response, and directional response. This reduced the mean deviation to -0.4% compared to the Cell Lab. Further, two independent BORCAL sessions were able to produce the same values to within ±0.2%. This could be a viable approach for verifying reference cells using existing BORCAL infrastructure, for example, to evaluate their long-term stability. The daily profiles of responsivity obtained during the BORCAL sessions (provided in Appendix A) show clear patterns of differences between models, which provides evidence that their directional responses differ from each other; thus, two sensors that are calibrated correctly might give the same reading at 30° zenith angle but systematically different readings at 60°. The impact of these inconsistencies in field operation will be quantified using the long-term observations started in 2020.

14 SOLAR ENERGY↗
DOE OSTI2020

Accelerate M-TIP on GPUs and deploy to Summit and NERSC-9 (against simulated data) WBS 2.2.4.05 ExaFEL, Milestone ADSE13-199

We evaluated the orientation matching step in the M-TIP SPI workflow for potential offloading to accelerators. We ported the code to GPUs, benchmarked it, optimized and down-selected the best versions. The accelerated version of the orientation matching code that was developed at LANL (LANL GPU v3) is 34-55X faster than sequential, 2.4-4.9X faster than the fastest OpenMP open source version we found (FAISS OpenMP) and 1.5-4X faster than the fastest GPU open source version we found (FAISS GPU). Summit single-node GPU versions were somewhat faster than Cori GPU. Image size plays a role; mid-range image sizes take more time. The LANL CUDA multi-node, multi-GPU implementation shows mostly linear strong scaling. I/O also plays a large role; splitting data into parts improves read time and burst buffers dramatically improve read times. This work will be integrated into the M-TIP workflow as part of the next milestone ADSE13-193.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Evaluating Barcode Size and Metal Surface Treatment Options for a Global UF 6 Cylinder Identifier

A team at Oak Ridge National Laboratory tested various barcode sizes, materials, surface finishes, and marking techniques to determine suitable direct part marking techniques and barcode specifications for a new uranium hexafluoride (UF 6 ) cylinder global identifier. This paper describes testing those variables at different read distances and angles with several commercial off-the-shelf direct part mark or barcode readers. This research concluded that a 1.4 in. 2D Data Matrix barcode with a 0.1 in. quiet zone would be appropriate for the machine-readable feature on the proposed UF 6 cylinder global identifier. Testing suggests that this size barcode could be read from an angle of up to 30° over the range of 10–100 cm using multiple commercial off-the-shelf handheld direct part mark or barcode readers. Testing also suggested that barcodes marked on ball-blasted stainless steel with CerMark laser marking ink may be a good choice for the proposed UF 6 cylinder global identifier because they exhibited high contrast and were readable from a desirable range of distances and angles.

42 ENGINEERING↗
DOE OSTI2022

The Automated Mobility District Implementation Catalog, 2nd Edition: Safe and Efficient Automated Vehicle Fleet Operations for Public Mobility

This second volume of the Automated Mobility District (AMD) Implementation Catalog series has been prepared in three parts to assist readers in their review and understanding of the technical information herein. The material may be more easily ingested if each of the three parts is read and then contemplated for its ramifications to the specific interest of the reader before continuing to the next part. Further, each part has been prepared with the intent that it could be read independently from the others. Part 1 is Progress of Automated Vehicle R&D for Deployments in Passenger Service; Part 2 is 10 Early Deployment Sites as Prototypes of AMD Implementation; Part 3 is Five Cardinal Principles for AMD Implementation.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Analysis Report for Determination of pH Correction Factors for Brines under AP-157 Rev.1

This Analysis Report (AR) documents the determination of pH correction factors for the observed pH readings. The correction factor converts the observed pH reading recorded from the brines used in geochemical studies in support of the Waste Isolation Pilot Plant (WIPP) to a corrected pH value. The data analysis in this AR falls under AP-157 Rev. 1 Analysis Plan for Determination of pH Correction Factors in Brines (Kirkes et al, 2021). Measurement of pH in some solutions can be challenging due to numerous factors such as high ionic strength, elevated or lowered temperature, complex matrix composition, etc. (Knauss et al., 1990; and Rai et al., 1995). The measured pH can be corrected by applying the correction factor, empirically obtained from a specific test solution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Nanosecond Gated CMOS Camera (NSGCC) ICD (Rev. 2.1)

The Ultra-Fast X-ray Imager (UXI) program is an ongoing effort at Sandia National Laboratories to create high speed, multi-frame, time-gated Read Out Integrated Circuits (ROICs), and a corresponding suite of photodetectors to image a wide variety of High Energy Density (HED) physics experiments on both Sandia’s Z-Machine and LLNL’s National Ignition Facility (NIF). Several cameras have been designed over the length of the program; one of the most recent is the Icarus, which is an improvement on past imagers (Furi and Hippogriff). A second sensor that can be connected is the Daedalus sensor. The Icarus is a 1024 × 512-pixel array with either 25 μm or 8 µm spatial resolution containing four frames of storage per pixel and has improved timing generation and distribution components while achieved 2 ns time gating. The Daedalus sensor is also a 1024 x 512-pixel array with 25 µm special resolution containing three frames of storage per pixel and has an increased set of features for a wider variety of applications from interlacing of rows in each frame to configurability of all shutters. See Section 14 for details regarding the Icarus implementation of the firmware and Section 15 for details regarding the Daedalus implementation. Due to the unique test environments UXI sensors are targeted for, full custom hardware was required to physically mount an Icarus or Daedalus sensor, manage its various functions, and read out pixel data for transfer to a host computer. Beyond experimental functionality, the hardware also needed to accommodate sensor characterization requirements. Lawrence Livermore National Laboratory’s ‘Version 4.0 Board’ was the result of these efforts. It mounts all the components required to fully utilize the Icarus and Daedalus sensors including analog to digital converters to convert pixel data and various system voltages to digital form for readout and analysis, DAC channels for remote configuration of critical bias voltages, static random-access memories to buffer pixel data, RS422 and Gigabit Ethernet communications for remote access, and an FPGA to tie these components together. This document describes the FPGA electrical interfaces in detail to allow the reader a greater understanding of the device, and to facilitate implementation of custom software to control and manage it. The Version 4.0 Board is a continuation of the Nano-second Gated CMOS hardware design that retains much of the functionality of the Version 1.0 Board while adding features including a DAC instead of digital potentiometers, as well as sensors for pressure and radiation. The Version 4.0 board is intended for applications requiring tight form-factor enclosures. It is composed of two stacking boards; one holds the FPGA and regulators to power the various components of the board while the other contains the mating connector to the sensor, image-readoff ADCs, the DAC, and other components.

42 ENGINEERING↗
DOE OSTI2023

Data Summary Report for Soil and Slab Sampling at Former Building 175

Lawrence Livermore National Security (LLNS) and the U.S. Department of Energy (DOE) are in the process of returning the area where Building 175 existed to beneficial use for future site development. The completed assessment will help LLNS and DOE to outline project scope and costs associated with the removal, characterization, and disposal of materials generated when the concrete slab for the former building and any associated remaining subsurface structures are demolished. Slab removal under the Transition & Disposition process requires full screening for potential site contamination to determine appropriate future land use. Borehole locations and depths were designed to correctly assess DOE’s future liability for characterizing residual vadose zone contamination. If a residual source area is identified at depth, DOE will need to evaluate the additional cost of future subsurface cleanup (with limited access) due to planned development. This is necessary to leave the location in a “ready-to-build” status. As a result, Phase II sampling requirements may in some cases extend beyond the construction zone required for slab removal to ensure the necessary due diligence. To avoid the potential spread of contamination and/or the creation of an environmental release by impacting the integrity of known contamination areas (e.g., pit within room 102 and the east to west boundary seam), these locations were not sampled for this project. During demolition of the slab, these locations and their underlying soils should be further evaluated. The assessment was conducted in accord with the May 2022 Lawrence Livermore National Laboratory Former Building 175 Assessment Soil Sampling and Analysis Plan / Quality Assurance Plan. Thirty-six, direct-push borings were advanced, along with collecting concrete (where present) and soil samples for laboratory analyses. Thirty-two of the borings were advanced to a depth of 25 feet below ground (bgs), and four borings were advanced to a depth of 55 feet bgs. The concrete slab for former Building 175 ranged from approximately 8 inches to over two feet in thickness. Soils encountered during the investigation consisted primarily of clayey silt, with interbeds of sandy gravel and silty sand to the total depth explored of 55 feet bgs. Field photoionization detector readings – checking for volatile organic compound (VOC) vapors in soils, ranged from zero (0) to a peak of 33 parts per million at 25 feet bgs in boring PC-B175- 028. The cause for the peak reading is unknown, however, no visually discolored or odorous soils were encountered during the assessment and all VOC results were below Lawrence Livermore National Laboratory’s (LLNL’s) Soil Screening and Management Plan (SSMP) soil screening levels (SSL). Groundwater was not encountered during the assessment and is expected to occur at roughly 65 feet bgs in the project area. No metals were detected at concentrations of concern in the concrete core samples collected and analyzed. Low gross alpha and beta activity concentrations were detected in the concrete core samples collected and analyzed. The detected activity concentrations would appear to be from naturally occurring radioactive isotopes, i.e., potassium 40, present in the raw materials used to make concrete and not artificially added. Tritium was not detected above the testing laboratory's Method Detection Limit (MDL) in any of the concrete core samples collected and analyzed. The radioactive isotopes - actinium 228, bismuth 214, lead 212, lead 214, potassium 40, radium 226, radium 228, and thallium 208, were detected at low activity concentrations in the concrete core samples analyzed. Based on the detected activity concentrations, the isotopes would appear to be naturally occurring in the raw materials used to make concrete and not artificially added. Acetone – a common laboratory contaminant, was detected in nine of the soil samples collected and analyzed. Concentrations of two other volatile organic compounds (benzene and tetrachloroethene) were detected in five of the soil samples analyzed. All concentrations were below SSLs. Total petroleum hydrocarbons as diesel range organics were detected at 43.9 milligrams per kilogram (mg/kg) in the 20-foot bgs duplicate sample from boring PC-B175-007. Total petroleum hydrocarbons as motor oil were detected at 7.20 mg/kg in the 15-foot bgs routine sample from boring PC-B175-001, and at 20.7 mg/kg in the 20-foot bgs duplicate sample from boring PC-B175-007. The SSL for diesel-range TPHs is 260 mg/kg. LLNL does not have an SSL for motor oil range TPHs. No indications of a release, e.g., visibly stained, or odorous soil, were present at the boring locations. No samples collected contained polychlorinated biphenyls (PCBs) in concentrations above the laboratory reporting limit. Arsenic was detected above its SSL of 8.51 mg/kg in the 25-foot bgs routine sample collected from boring PC-B175-023. Nickel was detected above its SSL of 86.0 mg/kg in the 10-foot bgs routine sample from boing PC-B175-005, the 20-foot bgs routine sample from boring PC-B175-025, and the 25-foot bgs routine sample from boring PC-B175-034. The detected concentrations, however, were well below ten times (10x) their respective STLCs. Gross alpha and/or gross beta were detected above their respective SSL activity concentrations in three routine soil samples. Retesting (two per sample) of the samples showed that the initial reported activity concentrations were anomalous. Tritium was not detected in any of the routine or duplicate soil samples collected and analyzed during the investigation. The radioactive isotopes - actinium 228, bismuth 212 and 214, lead 212 and 214, potassium 40, radium 224, 226 and 228, thallium 208, thorium 234 and uranium, were detected at low activity concentrations in the soil samples analyzed for radioactive constituents. The detected isotopes and their associated activity concentrations are typical of those naturally occurring in the marine-type sedimentary deposits underlying the Livermore Valley. No radiological controls are necessary for the soil evaluated.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

CrossLink: Meshing a 3D part from a STEP file [Slides]

This example shows how to use CrossLink to create a mesh for a 3D geometry part read in from a STEP file. A STEP file (Standard for the Exchange of Product data) is a common file format used for 3D modelling that can be written out from a CAD program (e.g., Creo Parametric). Being able to read and mesh STEP file geometries is essential for meshing parts from engineering models. Creating the mesh typically involves: (1) Importing the geometry; (2) Creating geometry groups; (3) Assigning curves and surfaces to the geometry groups; (4) Building a topology; (5) Applying geometric and mesh constraints; and (6) Generating the final mesh. Current issues with this process in CrossLink include: (1) The GUI does not display trimmed surfaces; (2) The user must manually create and assign geometry groups; and (3) The user must be aware of duplicate curves and surfaces from the CAD model.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

State Energy Justice Roundtable Series: Energy Justice Metrics

The National Association of Regulatory Utility Commissioners (NARUC), National Association of State Energy Officials (NASEO), and National Governors Association (NGA) hosted a State Energy Justice Roundtable (Roundtable) in April 2022. Participants included federal and state decision-makers, members of community-based organizations, and subject-matter experts. The Roundtable members explored current state efforts to articulate and incorporate energy justice concerns into energy-related decision-making. Participants established connections with one another to better understand the current landscape of existing resources, learn about emerging efforts, and identify ongoing support opportunities for advancing energy justice.This paper is one of five authored by the host organizations on topics that were the focus of the Roundtable. Each paper summarizes key themes, emerging efforts, and group takeaways that were discussed at the Roundtable and should assist state members in developing and meeting their own state goals around energy justice. The papers all include the same discussions of background, introduction, and reading list so they can be read separately. Each paper is written from the perspective of one association and includes options for its members to take actions that could support more equitable state energy policies and programs. The five papers cover: (1) Participation in decision making (NARUC), (2) Customer affordability and arrearages (NARUC), (3) Energy justice metrics (NARUC), (4) Equity in clean energy research and development (NASEO), and (5) Equitable distributed energy resource (DER) access (NGA). The resources and recommendations listed in these papers are not meant to be exhaustive, as this field of study continues to evolve. Although this brief is focused on electricity, energy justice considerations extend to all energy needs and services, including the impact of energy extraction, processing, and distribution functions.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

State Energy Justice Roundtable Series: Customer Affordability and Arrearages

The National Association of Regulatory Utility Commissioners (NARUC), National Association of State Energy Officials (NASEO), and National Governors Association (NGA) hosted a State Energy Justice Roundtable (Roundtable) in April 2022. Participants included federal and state decision-makers, members of community-based organizations, and subject-matter experts. The Roundtable members explored current state efforts to articulate and incorporate energy justice concerns into energy-related decision-making. Participants established connections with one another to better understand the current landscape of existing resources, learn about emerging efforts, and identify ongoing support opportunities for advancing energy justice. This paper is one of five authored by the host organizations on topics that were the focus of the Roundtable. Each paper summarizes key themes, emerging efforts, and group takeaways that were discussed at the Roundtable and should assist state members in developing and meeting their own state goals around energy justice. The papers all include the same discussions of background, introduction, and reading list so they can be read separately. Each paper is written from the perspective of one association and includes options for its members to take actions that could support more equitable state energy policies and programs. The five papers cover: (1) Participation in decision making (NARUC) (2) Customer affordability and arrearages (NARUC) (3) Energy justice metrics (NARUC) (4) Equity in clean energy research and development (NASEO) (5) Equitable distributed energy resource (DER) access (NGA). The resources and recommendations listed in these papers are not meant to be exhaustive, as this field of study continues to evolve. Although this brief is focused on electricity, energy justice considerations extend to all energy needs and services, including the impact of energy extraction, processing, and distribution functions.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

State Energy Justice Roundtable Series: Participation in Decision Making

The National Association of Regulatory Utility Commissioners (NARUC), National Association of State Energy Officials (NASEO), and National Governors Association (NGA) hosted a State Energy Justice Roundtable (Roundtable) in April 2022. Participants included federal and state decision-makers, members of community-based organizations, and subject-matter experts. The Roundtable members explored current state efforts to articulate and incorporate energy justice concerns into energy-related decision-making. Participants established connections with one another to better understand the current landscape of existing resources, learn about emerging efforts, and identify ongoing support opportunities for advancing energy justice. This paper is one of five authored by the host organizations on topics that were the focus of the Roundtable. Each paper summarizes key themes, emerging efforts, and group takeaways that were discussed at the Roundtable and should assist state members in developing and meeting their own state goals around energy justice. The papers all include the same discussions of background, introduction, and reading list so they can be read separately. Each paper is written from the perspective of one association and includes options for its members to take actions that could support more equitable state energy policies and programs. The five papers cover: • Participation in decision making (NARUC) • Customer affordability and arrearages (NARUC) • Energy justice metrics (NARUC) • Equity in clean energy research and development (NASEO) • Equitable distributed energy resource (DER) access (NGA). The resources and recommendations listed in these papers are not meant to be exhaustive, as this field of study continues to evolve. Although this brief is focused on electricity, energy justice considerations extend to all energy needs and services, including the impact of energy extraction, processing, and distribution functions.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Thrifty Array Format (TAF) file specifications

Thrifty Array Foram (TAF) files store numeric data in a binary format, minimizing storage requirements while preserving quick read access. Real data of any size and dimensionality can be stored in this format at varying degrees of numeric precision. Implicit array are associated with each dimension, eliminating the need to explicitly store uniformly-spaced grid vectors. Unlimited text comments may be included with the array for user documentation, and every file begins with a text synopsis of the binary structure. The format is deliberately designed for memory mapping, where portions of the array can be read without loading the entire file at once.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Creation of a Weather Drivers Test Suite for Inclusion in ASHRAE Standard 140

Weather conditions are an important boundary condition for building performance simulation (BPS) calculations. For existing test cases in ASHRAE Standard 140 "Method of Test for Evaluating Building Performance Simulation Software" (ANSI/ASHRAE 2020), it was assumed that the software being tested could adequately read and interpret the weather data in the provided standard weather files. As differences between the programs have been reduced and as more programs have shifted to sub-hourly time steps this assumption has become more stretched. To address these concerns a new test suite testing a program's ability to read and interpret the data from a standard weather file was developed. The purpose of the test suite is to test the use of the typical data used from standard weather files.

54 ENVIRONMENTAL SCIENCES↗