Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Power Generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Alteration of pool boiling heat transfer on metallic surfaces by in situ oxidation

The critical heat flux during pool boiling has been investigated for a range of applications including electrical power generation and thermal management. Reported experimental CHF values during pool boiling of water on flat metallic surfaces, however, show a large discrepancy across studies. Here, we address this discrepancy in CHF values by accounting for oxidation of metallic surfaces during boiling. We studied the effect of in situ oxidation on flat Cu and Ni surfaces by changing the duration that samples were held in saturated water before conducting boiling experiments. The morphology and chemical composition of surfaces after the boiling experiments were analyzed by atomic force microscopy and X-ray photoelectron spectroscopy, respectively. Cu surfaces showed gradually increasing CHF values as the duration in saturated water increased, which could be attributed to the increase in roughness due to the formation of Cu 2 O nanostructures. Conversely, Ni surfaces showed relatively stable CHF and morphology as a nearly flat layer of NiO formed, with one exception: formation of a highly wetting hydroxide, Ni(OH) 2 , on a Ni coupon held in saturated water for 24 h resulted in a uniquely high CHF value, signifying the importance of surface chemistry in addition to morphology. Finally, the fundamental mechanisms resulting in the wide spread of CHF values on metallic surfaces elucidated in this work will lead to more accurate estimation of CHF as well as a deeper mechanistic understanding of CHF values on engineered surfaces.

42 ENGINEERING↗
DOE OSTI2022

Measurements of the thermal conductivity of reference liquids using a modified transient hot-wire needle probe

Many power generation processes feature some type of working fluid that plays a critical role in the transfer of heat throughout the system. To optimize thermal efficiencies, an accurate characterization of the temperature-dependent thermal conductivity of the fluid is needed. Herein, this study develops a time-domain Modified Transient Hot-wire Needle Probe to overcome phenomena that have impaired traditional measurement techniques when the fluid is both corrosive and at an elevated temperature. First, the physical design of the instrument is presented to demonstrate features that limit interference from corrosion, electrical conduction, and convective and radiative heat transfer. Next, a governing equation for 1D (radial) heat conduction is fully developed using the thermal quadrupoles technique. A finite-element study is performed for validation. A sensitivity analysis is done to assess the time-dependent influence of critical parameters in the governing equation for several samples. Finally, thermal conductivity measurements are presented for seven different liquid substances by fitting the thermal model to experimental data across a range of temperatures. Reference correlations are included for comparison. The sample thermal conductivity and ambient temperature of the experimental conditions range from 0.125–16.5$\frac{W}{m·K}$ and 10–400°C, respectively. The total uncertainty, comprised of both the experimental design and fitting process, of all measurements is quantified.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Robust silane self-assembled monolayer coatings on plasma-engineered copper surfaces promoting dropwise condensation

Dropwise condensation is well known to result in better heat transfer performance owing to efficient condensate/droplet removal, which can be harnessed in various industrial heat/mass transfer applications such as power generation and conversion, water harvesting/desalination, and electronics thermal management. The key to enhancing condensation via the dropwise mode is thin low surface energy coatings (<100 nm) with low contact angle hysteresis. Ultrathin (<5 nm) silane self-assembled monolayers (or SAMs) have been widely studied to promote dropwise condensation due to their minimal thermal resistance and scalable integration processes. Such thin coatings typically degrade within an hour during condensation of water vapor. After coating failure, water vapor condensation transitions to the inefficient filmwise mode with poor heat transfer performance. We enhance silane SAM quality and durability during water vapor condensation on copper compared to state-of-the-art silane coatings on metal surfaces. We achieve this via (i) surface polishing to sub-10 nm levels, (ii) pure oxygen plasma surface treatment, and (iii) silane coating integration with the copper substrate in an anhydrous/moisture-free environment. The resulting silane SAM has low contact angle hysteresis (≈20°) and promotes efficient dropwise condensation of water for >360 hours without any visible sign of coating failure/degradation in the absence of non-condensable gases. We further demonstrate enhanced heat transfer performance (≈5-7× increase over filmwise condensation) over an extended period of time. Surface characterization data post-condensation leads us to propose that in the absence of non-condensable gases in the vapor environment, the silane SAM degrades due to reduction and subsequent dissolution of copper oxide at the oligomer-substrate interface. The experiments also indicate that the magnitude of surface subcooling (or condensation rate) affects the rate of coating degradation. Finally, this work identifies a pathway to durable dropwise promoter coatings that will enable efficient heat transfer in industrial applications.

42 ENGINEERING↗
DOE OSTI2026

Creep behavior of high-entropy alloys: A critical review

High-entropy alloys (HEAs) have been extensively investigated during the last two decades. While substantial progress has been made in understanding their phase stability, microstructure, and deformation mechanisms at room and cryogenic temperatures, the long-term creep behavior (>100 h) of HEAs at high temperatures (>0.6 T m , where T m is the melting temperature) remains relatively underexplored. This knowledge gap is critical, as many engineering applications, including those for power generation and propulsion, require materials with good creep resistance to maintain structural integrity over extended service lifetimes. This review provides a focused and critical assessment of the current understanding of high-temperature deformation and creep behavior of HEAs, with particular attention paid to face-centered cubic HEAs and body-centered cubic refractory HEAs. The underlying deformation mechanisms governing their creep response and the influence of phase stability at elevated temperatures are examined in detail. Recent studies reveal mechanistic differences between HEAs and conventional dilute alloys that do not always lead to improved creep resistance belying their initial promise. Based on these findings, we discuss the challenges in designing HEAs for high-temperature structural applications and outline future research directions that may lead to creep-resistant HEAs.

Creep↗
DOE OSTI2024

Evaluation of methods for characterizing the fine particulate matter emissions from aircraft and other diffusion flame combustion aerosol sources

The U. S. Environmental Protection Agency in collaboration with the U. S. Air Force Arnold Engineering Development Complex conducted the VAriable Response In Aircraft nvPM Testing (VARIAnT) 3 and 4 test campaigns to compare nvPM emissions measurements from a variety of diffusion flame combustion aerosol sources (DFCASs), including a Cummins diesel engine, a diesel powered generator, two gas turbine start carts, a J85-GE-5 turbojet engine burning multiple fuels, and a Mini-CAST soot generator. The VARIAnT research program has conducted four test campaigns to date with the VARIAnT 3 and 4 test campaigns focusing on BC mass instrument performance, use of gas turbine engine sources for BC mass instrument calibration, and the characterization of the aerosols produced from the combustion sources. Results from both campaigns revealed agreement of about 20% between the AVL Micro-Soot Sensor, the Cavity Attenuated Phase Shift (CAPS PMSSA) monitor and the thermal-optical reference method for elemental carbon (EC), independent of the calibration source used. For the Artium LII-300, the measured mass concentrations in VARIAnT3 fall within 18% and in VARIAnT4 fall within 32% of the reference EC mass concentration when calibrated on a combustor rig in VARIAnT3 and on a LGT-60 start cart in VARIAnT4, respectively. It was also found that the three mass instrument types (MSS, CAPS PMSSA, and LII-300) can exhibit different BC to reference EC ratios depending on the emission source that appear to correlate to particle geometric mean mobility diameter, morphology, or some other parameter associated with particle geometric mean diameter (GMD) with the LII-300 showing a slightly stronger apparent trend with GMD. Systematic differences in LII-300 measured mass concentrations have been reduced by calibrating with a turbine combustion source (combustor or turbine engine). With respect to the particle size measurements made, the sizing instruments (TSI SMPS, TSI EEPS, and Cambustion DMS 500) were found to be in general agreement in terms of size distributions and concentrations with some exceptions. Teflon filter measurements of the total aerosol mass produced by the various DFCASs differed from the reference EC, BC, and integrated particle sized distribution measured aerosol masses. The Teflon filter measured mass was 30 to 40% greater than the reference EC and 50 to 60% greater than the BC mass for the J85 in both test campaigns. The measurements of particle size distributions and single particle analysis by miniSPLAT indicated the presence of large particles (>100 nm) having more compact morphologies, higher effective density, and a composition dominated by OC and ash. This increased large particle fraction is also associated with higher values of single scattering albedo measured by the CAPS PMSSA instrument and higher OC/EC measurements. These measurements indicate gas turbine engine emissions can be a more heterogeneous mix of particle types beyond the original E31 assumption that it is mainly composed of black carbon.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Bridging the Energy Future: The Role and Potential of Hydrogen Co-Firing with Natural Gas

In the transition toward sustainable energy systems, the co-firing of hydrogen (H2) with natural gas emerges as a critical technology for cleaner power generation. This study examines its benefits, including emissions reduction, enhanced efficiency, and compatibility with existing infrastructure. Concurrently, it addresses the inherent challenges, such as combustion dynamics, necessary infrastructure modifications, and economic considerations. Incorporating global case studies, the review explores recent advancements in hydrogen production and co-firing, evaluating their practicality and operational efficiency. It also provides a critical examination of the economic implications and societal acceptance, which are crucial for the adoption of hydrogen technologies. Moreover, the review investigates the synergy between hydrogen and renewable energy technologies, assessing potential impacts on energy policy and regulation. Ultimately, this comprehensive analysis underscores the essential role of hydrogen co-firing in the energy sector and advocates for a comprehensive strategy that synergizes technological progress, economic viability, regulatory support, and public engagement to promote a resilient and sustainable energy future.

hydrogen co-firing↗
DOE OSTI2026

Trends and limits of CO 2 capture in solid and liquid sorbents at standard conditions

Carbon capture and storage (CCS) plays a critical role in achieving climate change mitigation targets, offering a pathway to decarbonize power generation, industrial processes, and heat production while addressing atmospheric CO 2 removal. While CCS technologies are technically advanced, the widespread adoption of 100 % CO 2 capture capacities such as 1 mol of CO 2 /mol of material and 1 g CO 2 /g storage (targeted by the DARPA, Defense Sciences Office, USA Govt.) has raised questions about the feasibility of achieving higher capture capacities. In the context of limiting global warming to 1.5°C, reaching 100 % CO 2 capture capacity is increasingly necessary, with residual emissions requiring complementary carbon dioxide removal (CDR) technologies. This review exclusively focuses on the CO 2 capture capacities of various sorbents under standard conditions, using different evaluation metrics. This study explores the performance of solid and liquid sorbents under standard conditions, analyzing factors including surface area, pore structure, solvent type, and functionalization to identify materials optimized for industrial-scale CCS applications. Emerging sorbents, including ILs, MOFs, COFs, POPs, DES, RCC, hybrid materials, and reactive sorbents, offer significant potential for enhanced selectivity and energy-efficient regeneration. Through a systematic assessment of gravimetric, volumetric, and molar capacities, the study provides insights into material efficiencies and trade-offs, offering guidance on optimizing sorbent selection for specific applications. The research advances understanding of scalable CCS technologies, contributing to global efforts to achieve net-zero emissions and address the pressing challenge of climate change.

Absorption↗
DOE OSTI2025

Creep performance and microstructure of grade 91 steel weldments with integrated welding and thermal processing

Ferritic-Martensitic steel welds typically require post weld heat treatment (PWHT) to restore toughness and high temperature performance. This off-line thermal process reduces disparities between weld and base metal, but can cause distortion, cracking, or simply be impractical due to assembly size and joint non-uniformity. Here we show integrated welding and thermal processing applied to modified 9Cr-1Mo (Grade 91) steel, favored for advanced power generation applications, performed in real time through the addition of a secondary heat source near the primary weld head. Optimal integrated processing reduces weld fusion and heat affected zone hardness by 125 HV, approaching performance of conventional 730 °C, 60 min PWHT processing. Microstructures and mechanical performance are compared for mechanized GTAW welds, with equivalent lifetimes noted in cross-weld creep rupture tests up to 234 MPa at 550 °C, and up to 104 MPa at 650 °C. The integrated process was validated on a Grade 91 pressure vessel with multipass cold wire feed GTAW. After 550 °C, 71.4 bar thermomechanical cyclic testing, the maximum weld hardness is <350 HV.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-performance and stable AgSbTe 2 -based thermoelectric materials for near room temperature applications

AgSbTe 2 -based ternary chalcogenides show excellent thermoelectric performance at low- and middle-temperature ranges, yet their practical applications are greatly limited by their intrinsic poor thermodynamic stability. In this work, we demonstrate that AgSbTe 2 -based ternary chalcogenides can be stabilized for service below their decomposition threshold. A series of Ag x Sb 2-x Te 3-x (x = 1.0, 0.9, 0.8 and 0.7) samples have been prepared by the melt-quenching method. Among them, phase pure Ag 0.9 Sb 1.1 Te 2.1 is verified by comprehensive structural characterizations from macroscale by X-ray diffraction to microscale by energy-dispersive spectroscopy and then to sub-nanometer scale by atom probe tomography. This composition is further chosen for the stability investigation. The decomposition threshold of Ag 0.9 Sb 1.1 Te 2.1 appears around 473K. Below this temperature, the chemical compositions and thermoelectric properties are barely changed even after 720 h annealing at 473 K. The figure-of-merit (zT) value of Ag 0.9 Sb 1.1 Te 2.1 below the decomposition threshold is very competitive for real applications even compared with Bi 2 Te 3 -based alloys. The average zT of Ag 0.9 Sb 1.1 Te 2.1 at 300–473 K reaches 0.84, which is higher than most other thermoelectric materials in a similar temperature range, promising applications in miniaturized refrigeration and power generation near room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermoelectrics: From longitudinal to transverse

Thermoelectric power generation is a promising technology to realize a sustainable society because it directly converts thermal energy into electricity in a solid. Conventional thermoelectric generation is driven by the Seebeck effect, discovered by T.J. Seebeck in 1821, in which a charge current J c is generated in the direction parallel to a temperature gradient ∇T, the longitudinal geometry. Here, the ratio between the generated longitudinal electromotive force and applied ∇T is defined as the Seebeck coefficient. As shown in Figure 1A, a thermoelectric module based on the Seebeck effect typically consists of many pairs (128 for a 12V unit) of p-type and n-type conductors alternately arranged and connected in series. Since the Seebeck coefficient of a p-type (n-type) conductor is positive (negative), the thermopower in each element adds to the total output in the Seebeck module. This configuration is needed to achieve a practical voltage because each element only supplies millivolts but limits the use of thermoelectric generators. The efficiency of thermoelectric generators is characterized by the thermoelectric figure of merit, zT. Despite a 3-fold improvement in zT resulting from materials research over the last two decades, little progress has been made in their practical use; this is ascribed to the technological challenges in contact technology. The contacts on the hot side are subject to thermal degradation. All contacts (512 for a 12V unit) add electrical and thermal contact resistances that reduce the device efficiency to a fraction of that promised by the materials.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

The effect of water vapor on surface oxygen exchange kinetics of thin film (La,Sr)(Co,Fe)O 3-δ

Oxygen reduction and transport in electrochemical applications are strongly affected by the reactant gas composition, including impurities such as water. Understanding the relationship between oxygen reactivity and humidity is key for attaining stability and high efficiency of solid oxide fuel cells, which are especially attractive for transportation applications as low emission power generation devices. Both short- and long-term effects of moisture have previously been associated with use of ambient air. To better understand these effects, we study oxygen exchange kinetics at the cathode surface and the cathode/electrolyte interface using La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) epitaxial thin films as a model-surface system. In situ synchrotron X-ray techniques evaluate the oxygen reduction reaction (ORR) kinetics in response to environmental variables. The results suggest a clear enhancement of the ORR rate upon short term exposure of the perovskite-structured films to water. Finally, on the basis of these measurements, along with in situ X-ray characterization of Sr segregation and computational first-principles studies, we suggest a model for this increased ORR activity that may lead to further improvements by stabilizing active cathode surface configurations.

25 ENERGY STORAGE↗
DOE OSTI2020

Impact of electrode thick spot irregularities on polymer electrolyte membrane fuel cell initial performance

Polymer electrolyte membrane fuel cells have great potential for power generation in many applications, but to implement them on a larger scale, understanding of quality requirements, tolerances, and controls during manufacturing must improve. As part of this broad challenge, irregularities resulting from the membrane electrode assembly production process must be studied to determine if they impact the performance of the cell. One potential irregularity is a locally increased thickness of the coated or deposited electrode. In order to understand and provide insight into the impact of such irregularities, we intentionally created thick spots in the center of cathode electrodes. The thick spots fabricated by two different approaches were carefully characterized by optical microscopy, X-ray fluorescence spectroscopy and scanning electron microscopy (SEM). We found that the impact of the thick spots on the electrochemically active catalyst area and mass activity was minimal. However, specific electrode thick spot irregularities significantly impacted the mass transport properties of the cells. Based on SEM analysis, the likely cause of the performance drop is morphological changes associated with the creation of the thick spot irregularity. Spatial performance results obtained with a segmented cell system further indicated that the area of the performance impact exceeded that of the intentionally created thick spot.

25 ENERGY STORAGE↗
DOE OSTI2021

High-fidelity wind farm simulation methodology with experimental validation

The complexity and associated uncertainties involved with atmospheric-turbine-wake interactions produce challenges for accurate wind farm predictions of generator power and other important quantities of interest (QoIs), even with state-of-the-art high-fidelity atmospheric and turbine models. A comprehensive computational study was undertaken with consideration of simulation methodology, parameter selection, and mesh refinement on atmospheric, turbine, and wake QoIs to identify capability gaps in the validation process. For neutral atmospheric boundary layer conditions, the massively parallel large eddy simulation (LES) code Nalu-Wind was used to produce high-fidelity computations for experimental validation using high-quality meteorological, turbine, and wake measurement data collected at the Department of Energy/Sandia National Laboratories Scaled Wind Farm Technology (SWiFT) facility located at Texas Tech University’s National Wind Institute. The wake analysis showed the simulated lidar model implemented in Nalu-Wind was successful at capturing wake profile trends observed in the experimental lidar data.

17 WIND ENERGY↗
DOE OSTI2023

Ultrathin polyorganosilica membranes synthesized by oxygen-plasma treatment of polysiloxanes for H 2 /CO 2 separation

Oxygen plasma treatment of polydimethylsiloxane (PDMS) induces an ultrathin polyorganosilica (POSi) layer (<10 nm) on top of a PDMS membrane, leading to excellent H 2 /gas separation properties and providing a rapid and scalable way to fabricate robust silica membranes compared with conventional high-temperature and time-consuming sol-gel methods. Here, we thoroughly investigate POSi membranes derived from poly (dimethylsiloxane-co-methylhydroxidesiloxane) (poly (DMS-co-MHOS)) containing -SiOH groups that can be more easily converted to silica networks than the -SiCH 3 in PDMS. Further, the effect of the polysiloxane structure and plasma treatment conditions (including plasma generating powers, oxygen flowrate, chamber pressure, and treatment time) on the silica chemistry, structure, and H 2 /CO 2 separation properties are systematically determined to derive structure/property relationships. An optimized membrane exhibits H 2 permeance of 880 GPU and H 2 /CO 2 selectivity of 67 at 150 °C, superior to state-of-the-art polymeric membranes. The membrane retains H 2 /CO 2 selectivity as high as 46 when challenged with simulated syngas containing 2.8 mol% water vapor at 150 °C, demonstrating the potential of these POSi membranes for practical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Modeling aqueous association constants and mineral solubilities at subcritical and supercritical temperatures

The need for sustainable power generation has increased interest in the use of hydrothermal fluids for industrial applications. New high-enthalpy geothermal systems and biowaste-to-fuel processes are two relevant examples that employ supercritical fluids which require an in-depth understanding of complex chemical reactions occurring near the supercritical temperature of water (374 °C). As these processes operate in thermodynamic regimes that are not currently covered by a standard molar Gibbs energy of formation model, only empirical fits for single reaction systems are available which limit the use of multi-component phase equilibria calculations that are standard practice for less extreme environments. Here, in this paper, we advance a standard molar Gibbs energy of formation model able to operate in these otherwise inaccessible thermodynamic states to include species needed for key mineral solubility systems and ion association reactions. This work extends a model based on molecular statistical thermodynamics (MST) into four new systems (Na 3 PO 4 -H 2 O, LiOH-H 2 O, KOH-H 2 O, and BaSO 4 -H 2 O) by extending the model to cover 10 new species. For each of these systems, model predictions were consistently within the experimental uncertainties for the new systems covered. A breakdown of MST contributions to the model revealed that electrostatic and hard sphere contributions were key to reproducing density dependencies of standard molar Gibbs energy of formation values around the critical point of water.

42 ENGINEERING↗
DOE OSTI2020

Characterization of precipitation in gradient Inconel 718 superalloy

Inconel 718 (IN718) superalloy is a well-established material for the application of aircraft engine and power generator due to its excellent performance at high temperatures. The outstanding mechanical properties of IN718 are largely determined by the precipitates. Here, we investigated the precipitation behaviors and the corresponding mechanical properties of the heat-treated gradient IN718 alloy. The microscopy studies reveal that high-density hexagonal η phase with chemistry of Ni 3 (Al,Ti,Nb) formed in the nanograined IN718 alloy after annealing at 700 °C. Additionally, the compressive stress introduced during severe plastic deformation may have prohibited the formation of γ” phase while accelerated the precipitation of γ’ phase, consequently favoring the precipitation of η phase. The corresponding evolution of mechanical behavior of gradient IN718 alloy is investigated.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The performance of additively manufactured Haynes 282 in supercritical CO 2

The use of supercritical carbon dioxide (sCO 2 ) as a working fluid is garnering interest in next generation power production systems due to the possibility of increased operational efficiencies and lower associated costs. Its implementation requires alloys with excellent high temperature strength and corrosion resistance, which makes Haynes 282® (H282) a suitable candidate. With increasing adoption of additive manufacturing (AM) in the energy industry, there is a need to investigate long-term sCO2 exposure on AM produced materials. Additively manufactured H282 (AM-H282) samples built using laser powder bed fusion in two different orientations were analyzed through imaging, gravimetric analysis, and room-temperature tensile testing before and after 1000-h exposure to CO 2 at 750 °C and 20 MPa. Performed imaging included observation of the sample surfaces and of the material bulk (cross sections) through means of Scanning Electron Microscopy (SEM) and optical microscopy. In comparison to wrought H282, it was found that the exposed material exhibited a similar Cr 2 O 3 oxide protective layer about 2 μm in thickness with additional top-surface TiO 2 oxide and carbon-rich precipitates. It was also similarly observed that internal oxidation was present but limited to a depth of 20 μm, and a 1–3 μm γ’ denuded region appeared to surround all internal and surface oxidation. Thermal aging effects were noted with the precipitation of needle-like structures in the γ/γ’ matrix and a coarsening of the γ’ precipitates from 28 nm to 73 nm. Mass measurements analyzing oxide precipitation revealed a larger increase compared to wrought, representing an approximate 20% difference. Tensile testing results showed similar behavior to wrought with a slight increase in yield strength and a large reduction in elongation in the exposed samples.

36 MATERIALS SCIENCE↗