Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Performance optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Development and Validation of Home Comfort System for Total Performance Deficiency/Fault Detection and Optimal Comfort Control

In this project, we developed and tested a learning-based home thermal model that facilitates the operation of a model predictive control (MPC)-based optimization agent and an automated fault detection and diagnosis (AFDD) agent. The home thermal model was constructed using a two-node resistor-capacitor model. Moreover, two accompanying parameter identification methods were introduced, least-squares and optimization. Based on the home thermal model, the MPC-based optimization agent was developed to optimize residential HVAC operation. Using two FDD methods, the AFDD agent was constructed to detect and diagnose two prevalent residential AC faults, airflow reduction and refrigerant undercharge. The home thermal model, along with the MPC-based optimization agent and AFDD agent, were tested at the Norman Test House, Miami Test House, Pacific Northwest National Laboratory (PNNL) Test House A, and PNNL Test House B. Finally, they were also field tested in nine demonstration homes with real occupants.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Complete Performance Comparison Between the Optimized Image Construction Algorithm (U-MBIR) and the Existing Reconstruction Algorithm for Detecting Defects and Damage in Concrete

Reinforced concrete (RC) is a composite material subjected to mechanical, thermal, and chemical loads throughout its service life. Because of these external stressors and the susceptibility of RC structural members to shrinkage and microcracking, the material degrades throughout its life cycle. This deterioration can lead to a decrease in member capacity and, ultimately, poses a threat to the structural integrity. Thus, it is crucial that the damage caused by aging and degradation be monitored and assessed at regular intervals throughout the material’s service life. Since coring of the material is typically not feasible for in-service structural systems, non-destructive evaluation (NDE) methodologies are used to assess remaining structural capacity. NDE methods enable surface and subsurface examination without damaging or degrading the medium. Moreover, RC is a critical component of nuclear power plants; thus, its safety and reliability must be thoroughly examined throughout the life cycle of the structural system. Ultrasonic measurements have been an industry standard for both surface and subsurface inspections. To this end, Oak Ridge National Laboratory (ORNL) has researched and developed advanced image reconstruction algorithms to capture internal damage. The results and discussion presented herein summarize the current state of the ultrasonic model–based iterative reconstruction (U-MBIR) algorithm developed at ORNL. More specifically, this report presents a comparison between reconstruction images produced via a widely employed ultrasonic NDE technique—the synthetic aperture focusing technique (SAFT)—and the ORNL-developed U-MBIR algorithm. These NDE methodologies are demonstrated using ultrasonic data collected from four concrete specimens. Overall, the U-MBIR algorithm eliminates artifacts and noise that are typically present within the SAFT reconstructions, and it shows defects and anomalies more clearly than the SAFT images. In conclusion, this algorithm is suitable for identifying concrete defects, although more improvements and optimization could be done to better define internal defects.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Model Choice Metrics to Optimize Profile-QSAR Performance

Predicting molecular activity against protein targets is difficult because of the paucity of experimental data. Approaches like multitask modeling and collaborative filtering seek to improve model accuracy by leveraging results from multiple targets, but are limited because different compounds are measured with different assays, leading to sparse data matrices. Profile-QSAR (pQSAR) 2.0 addresses this problem by fitting a series of partial least squares models for each target, using as features the predictions from single-task models on the remaining targets. Here, this method has been shown to produce better results than single task and multitask models. However, the factors determining the success of pQSAR 2.0 have as yet not been characterized. In this paper we examine the experimental conditions that lead to better pQSAR models. We limit the amount of data available to the method by retraining with decreasing amounts of data and explore the model’s ability to generalize to compounds that have never been assayed. Finally, we look at the properties of training data needed to demonstrate pQSAR improvement.

Biological and medical sciences, Computer science↗
DOE OSTI2017

Steady-State Subchannel Thermalhydraulic Assessment of Thorium-Based Fuel Concepts for Use in Pressure Tube Heavy Water Reactors

Thorium is an abundant alternative fertile nuclear fuel that could potentially be implemented in pressure tube heavy water reactors (PT-HWR) in the near future. One of the key stages in developing the thorium-based fuels for PT-HWRs is the reactor core concept, which requires the collaboration of different disciplines, such as neutron physics, thermal-hydraulics, materials, chemistry, safety, and others. Currently there are numerous core concepts under investigation at the Canadian Nuclear Laboratories that involve several types of thorium-based fuels, and that could be implemented in a 700-MWe-class PT-HWR. Four fuel bundle concepts are considered, including i) the reference (or nominal) 37-element bundle; ii) a 37-element modified bundle, with the center element using a different fuel material; iii) a 35-element bundle design, and iv) an 18-element internally cooled annular fuel (ICAF-18) fuel bundle. This study presents preliminary results of the steady-state thermalhydraulic subchannel analyses of the hot channels of different PT-HWR core concepts using thorium-augmented or thorium-based fuels. A follow up study will be initiated to improve the assessment of the proposed cores and associated fuel bundle concepts for thorium-augmented and thorium-based fuels. The computational model will be revisited to include; - Expanding the analysis to cover different power profiles at different burnup stages of the bundle. - Expand the analysis to cover 28.5 kg/s. - Reduce the eccentricity of the 35-element fuel bundle. - Assess the effect of the phenomena not yet included in the subchannel model (such as the effect of cold wall, and gamma heat). - Expand the analysis to include the effect of spacers and junctions. - Compare bundle concepts using other performance indicators (such as burnup, breeding ratio), as optimizing the fuel bundle geometry is a multidisciplinary problem.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Utilizing data-based modeling with low life cycle GHG emissions algae biofuels for engine optimization

Aquatic microalgae are a highly promising feedstock for the production of biocrude and tailored biofuels, with distinct advantages over traditional terrestrial crops, such as reduced land use and avoidance of food production competition. However, unlocking their full potential requires the development of biofuels with low life cycle greenhouse emissions biofuels, such as algae biofuels, which can significantly reduce the environmental impact of the transportation systems without requiring a complete overhaul of existing engine technology. In this study, we employ cutting-edge data-based AI modeling techniques to optimize the performance of heavy-duty engines, with a focus on transitioning towards biofuels with low life cycle greenhouse emissions biofuels. Our methodology offers significant advantages over traditional sweep testing, enabling efficient and accurate optimization of engine performance with minimal time and resources consumption. Our findings demonstrate the potential of utilizing this approach, with up to 55% NOx emissions reductions and up to 2% reduction in fuel consumption compared to the baseline optimized point. Moving forward, we plan to utilize a 30% blend of algae biofuels with diesel fuel, with the ultimate goal of achieving up to 60% lifecycle GHG emissions. Lastly, we plan to compare the results with 100% renewable biodiesel to add an additional dimension of investigating the impact of fuel chemistry on engine optimization. Overall, this study underscores the vital importance of biofuels for reducing the carbon footprint of the transportation sector and supporting a sustainable future. By harnessing the power of data-based AI modeling with low life cycle greenhouse emissions biofuels, we can accelerate the adoption of more environmentally friendly transportation systems and reduce their impact on the planet. Our findings contribute to this transition and offer insights for developing efficient and effective strategies for addressing global climate change.

09 BIOMASS FUELS↗
DOE OSTI2020

Optimal control of coupled quantum systems based on the first-order Magnus expansion: Application to multiple dipole-dipole-coupled molecular rotors

This paper presents a method for performing approximate optimal control simulations for quantum systems with multiple coupled degrees of freedom. In this work, the time evolution is simulated using the first-order Magnus expansion in the interaction picture, where the couplings between different degrees of freedom are treated as the perturbation. A numerical implementation procedure is presented that leverages upon pairwise couplings and the separability of the zeroth-order time evolution operator to achieve a reduced computational cost, which is analyzed with respect to the number of degrees of freedom. The formulation is compatible with gradient-free methods to optimize the control field, and a stochastic hill climbing algorithm is adopted for this purpose. As illustrations, optimal control simulations are performed for systems of two and three dipole-dipole-coupled molecular rotors under the influence of a control field. For the two-rotor system, the field is optimized to achieve either orientation or entanglement objectives. For the three-rotor system, the field is optimized either to orient all three rotors in the same direction or to orient one rotor in a particular direction while the other two rotors point in the opposite direction.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2014

Orbital-dependent second-order scaled-opposite-spin correlation functionals in the optimized effective potential method

The performance of correlated optimized effective potential (OEP) functionals based on the spin-resolved second-order correlation energy is analysed. The relative importance of singly- and doubly- excited contributions as well as the effect of scaling the same- and opposite- spin components is investigated in detail comparing OEP results with Kohn–Sham (KS) quantities determined via an inversion procedure using accurate ab initio electronic densities. Special attention is dedicated in particular to the recently proposed scaled-opposite–spin OEP functional [I. Grabowski, E. Fabiano, and F. Della Sala, Phys. Rev. B 87, 075103 (2013)] which is the most advantageous from a computational point of view. We find that for high accuracy, a careful, system dependent, selection of the scaling coefficient is required. We analyse several size-extensive approaches for this selection. Finally, we find that a composite approach, named OEP2-SOSh, based on a post-SCF rescaling of the correlation energy can yield high accuracy for many properties, being comparable with the most accurate OEP procedures previously reported in the literature but at substantially reduced computational effort.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Optimization of thermal barrier coating performance and durability over a drive cycle

A methodology to thermo-mechanically optimize a piston thermal barrier coating over a full drive cycle was established. The optimization objective was to minimize the heat transfer to the engine wall while maintaining structural integrity of the coating. Over 800 candidate materials were investigated and the optimization required more than one million non-road transient drive cycle calculations; real materials were investigated to ensure a realizable result and the existence of thermal and mechanical properties. High computational efficiency was achieved using a recently developed analytical heat transfer technique for multilayer engine walls. An uncoupled approach was utilized for the optimization, wherein the gas temperature and heat transfer coefficient profiles from a fully coupled and calibrated baseline model over the 20-min drive cycle were employed. The coating/piston interface temperature was constrained to be below the maximum piston service temperature limit. The durability was assessed using a recently developed analytical coating delamination framework for engine in-cylinder coatings based on the energy release rate when a crack forms. Results are presented for a mechanically unconstrained optimization and for cases constrained to three fixed levels of drive-cycle maximum energy release rate, and also constrained by the individual material’s toughness. The best-performing coating materials identified were verified using the fully coupled system-level model, which compared well to the uncoupled predictions. A study on the effect of adding a sealing layer to some high-performing, but porous, coatings showed a reduction in fuel consumption benefit and an increased exhaust temperature over the cycle, but the system still outperformed the uncoated case. The results of the study elucidate the importance of including engine performance and mechanical failure considerations in thermal barrier coating design.

Engineering↗
DOE OSTI2015

Simple Example of Backtest Overfitting (SEBO)

In the field of mathematical finance, a "backtest" is the usage of historical market data to assess the performance of a proposed trading strategy. It is a relatively simple matter for a present-day computer system to explore thousands, millions or even billions of variations of a proposed strategy, and pick the best performing variant as the "optimal" strategy "in sample" (i.e., on the input dataset). Unfortunately, such an "optimal" strategy often performs very poorly "out of sample" (i.e. on another dataset), because the parameters of the invest strategy have been oversit to the in-sample data, a situation known as "backtest overfitting". While the mathematics of backtest overfitting has been examined in several recent theoretical studies, here we pursue a more tangible analysis of this problem, in the form of an online simulator tool. Given a input random walk time series, the tool develops an "optimal" variant of a simple strategy by exhaustively exploring all integer parameter values among a handful of parameters. That "optimal" strategy is overfit, since by definition a random walk is unpredictable. Then the tool tests the resulting "optimal" strategy on a second random walk time series. In most runs using our online tool, the "optimal" strategy derived from the first time series performs poorly on the second time series, demonstrating how hard it is not to overfit a backtest. We offer this online tool, "Simple Example of Backtest Overfitting (SEBO)", to facilitate further research in this area.

Wu, K. John↗
DOE OSTI2013

Adaptive Liver Stereotactic Body Radiation Therapy: Automated Daily Plan Reoptimization Prevents Dose Delivery Degradation Caused by Anatomy Deformations

Purpose: To investigate how dose distributions for liver stereotactic body radiation therapy (SBRT) can be improved by using automated, daily plan reoptimization to account for anatomy deformations, compared with setup corrections only. Methods and Materials: For 12 tumors, 3 strategies for dose delivery were simulated. In the first strategy, computed tomography scans made before each treatment fraction were used only for patient repositioning before dose delivery for correction of detected tumor setup errors. In adaptive second and third strategies, in addition to the isocenter shift, intensity modulated radiation therapy beam profiles were reoptimized or both intensity profiles and beam orientations were reoptimized, respectively. All optimizations were performed with a recently published algorithm for automated, multicriteria optimization of both beam profiles and beam angles. Results: In 6 of 12 cases, violations of organs at risk (ie, heart, stomach, kidney) constraints of 1 to 6 Gy in single fractions occurred in cases of tumor repositioning only. By using the adaptive strategies, these could be avoided (<1 Gy). For 1 case, this needed adaptation by slightly underdosing the planning target volume. For 2 cases with restricted tumor dose in the planning phase to avoid organ-at-risk constraint violations, fraction doses could be increased by 1 and 2 Gy because of more favorable anatomy. Daily reoptimization of both beam profiles and beam angles (third strategy) performed slightly better than reoptimization of profiles only, but the latter required only a few minutes of computation time, whereas full reoptimization took several hours. Conclusions: This simulation study demonstrated that replanning based on daily acquired computed tomography scans can improve liver stereotactic body radiation therapy dose delivery.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2020

Characterization of Mechanical Performance of Composites Fabricated Using Innovative Carbon Fiber Wet Laid Process

Recent innovation in production of optimized nonwoven wet laid (WL) carbon fiber (CF) mats raised the question of optimal translation of the performance and isotropy into composites formed through these dry preforms. This work explores the mechanical behavior of composites produced from WL-CF mats in conjunction with the microstructure predicted through Object Oriented Finite Element Analysis (OOF). The mats used for the composites were prepared in two dispersion regimes using 25.4 mm long CF. The mixing regimes discussed in the author’s previous work, are identified as Method 1 for the traditional processing regime and Method 2 for the innovative regime that provided optimal nonwoven WL-CF mats. Composite panels from Method 2 mats showed a normalized tensile strength increase of 52% over those from Method 1 panels. Reproducibility analysis of composites made from Method 2 mats demonstrated a standard deviation of 2% in fiber weight content, 2% in tensile modulus and 9% in tensile strength, while composites made from Method 1 mats demonstrated a standard deviation of 5% in fiber weight content, 5% in tensile modulus and 17% in tensile strength. Systematic study of the microstructure and its analysis through OOF confirmed the isotropy translation of mats produced through method 2 to the composites. This study validated the hypothesis that optimal nonwoven mats lead to a well-balanced composite with optimal performance and that non-optimal nonwoven mats do not pack into a well-balanced composite.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Stabilizing dynamic subsea power cables using Bi-stable nonlinear energy sinks

This study investigates vibration mitigation of dynamic subsea cables through passive bi-stable nonlinear energy sinks (B-NESs). These devices suppress vibration energy in a broadband way, and can be regarded as extensions of classical linear tuned mass dampers (TMDs) which are narrowband devices. Through the open-source MoorDyn library, we simulated the vibrations of a vertical subsea cable equipped with a set of B-NESs. Multi-objective optimization was performed to detect the B-NES parameters for optimal mitigation of the cable vibrations. Advanced signal processing verified the efficacy of the optimized B-NESs not only to rapidly absorb and locally dissipate vibration energy, but also to nonlinearly scatter vibration energy from low to high frequencies within the cable itself. This last feature is especially beneficial for vibration mitigation of the undersea cable, as at higher frequencies the cable vibrations exhibit drastically reduced amplitudes and are more effectively dissipated by inherent structural damping and hydrodynamic radiation damping. This contrasts with traditional TMDs which can mitigate vibration only at a single frequency. Furthermore, our robustness study confirms the B-NES's effectiveness under even varying environmental conditions. Overall, the B-NES's capacity for broadband vibration mitigation renders it a promising retrofit solution for improving the performance and operational safety of dynamic power cables in offshore wind farms and other marine applications.

17 WIND ENERGY↗
DOE OSTI2023

Baseline Fuel Fabrication Facility

PRO-RR is the research reactor focused program element of the broader Proliferation Resistance Optimization program (PRO-X) under the National Nuclear Safety Administration (NNSA) in the U.S. Department of Energy (DOE). PRO-X provides a framework for integrating proliferation resistance in nuclear system designs to minimize weapons usable nuclear materials (WUNM) production and diversion pathways while optimizing systems performance for peaceful use missions. PRO-RR applies the PRO-X mission objectives to research reactor system design. This document serves as one of the foundational documents for the PRO-RR-Fuel System Design technical team by documenting a baseline fuel fabrication facility to be used for further optimization studies. The PRO-RR-Fuel System Design technical team consists of subject matter experts from Argonne National Laboratory (Argonne) and Savannah River National Laboratory (SRNL). In order to develop specific strategies for fuel fabrication facilities to optimize proliferation resistance, performance, and safety, a baseline fuel fabrication facility design basis was developed. Having a baseline design basis allows for the qualitative and quantitative comparison of design choices in the optimization process. This report describes the baseline fuel fabrication facility and general optimization strategy. Chapter 2 describes the fuel system selected for examination, the fabrication process used as the baseline, a description of the model developed to track uranium utilization, and a generic floorplan of the fabrication facility. Chapter 3 describes the overarching optimization strategy that could be implemented for a fabrication facility.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2015

SU-E-T-436: Fluence-Based Trajectory Optimization for Non-Coplanar VMAT

Purpose: To investigate a fluence-based trajectory optimization technique for non-coplanar VMAT for brain cancer. Methods: Single-arc non-coplanar VMAT trajectories were determined using a heuristic technique for five patients. Organ at risk (OAR) volume intersected during raytracing was minimized for two cases: absolute volume and the sum of relative volumes weighted by OAR importance. These trajectories and coplanar VMAT formed starting points for the fluence-based optimization method. Iterative least squares optimization was performed on control points 24° apart in gantry rotation. Optimization minimized the root-mean-square (RMS) deviation of PTV dose from the prescription (relative importance 100), maximum dose to the brainstem (10), optic chiasm (5), globes (5) and optic nerves (5), plus mean dose to the lenses (5), hippocampi (3), temporal lobes (2), cochleae (1) and brain excluding other regions of interest (1). Control point couch rotations were varied in steps of up to 10° and accepted if the cost function improved. Final treatment plans were optimized with the same objectives in an in-house planning system and evaluated using a composite metric - the sum of optimization metrics weighted by importance. Results: The composite metric decreased with fluence-based optimization in 14 of the 15 plans. In the remaining case its overall value, and the PTV and OAR components, were unchanged but the balance of OAR sparing differed. PTV RMS deviation was improved in 13 cases and unchanged in two. The OAR component was reduced in 13 plans. In one case the OAR component increased but the composite metric decreased - a 4 Gy increase in OAR metrics was balanced by a reduction in PTV RMS deviation from 2.8% to 2.6%. Conclusion: Fluence-based trajectory optimization improved plan quality as defined by the composite metric. While dose differences were case specific, fluence-based optimization improved both PTV and OAR dosimetry in 80% of cases.

60 APPLIED LIFE SCIENCES↗