Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PELLETING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Using Holey Graphene for Improved Interfacial Contact in Solid Electrolyte Ionic Conductivity Measurements

Solid-state batteries (SSBs) are poised to become the batteries of the future with advantages such as higher energy density, lighter weight, versatile geometry, and greater safety due to low flammability risk. An important parameter of the solid electrolyte (SE) used is its ionic conductivity. The ionic conductivity is generally calculated from the bulk resistance of a SE pellet, measured from the electrochemical impedance spectroscopy data. The SE pellet is typically prepared from the electrolyte powder by dry compression and is sandwiched between two blocking current collectors to obtain the impedance spectroscopy data. One of the challenges in conducting this measurement is poor interfacial contacts between the SE pellet and the current collector surfaces. Therefore, measurements reported in the literature may underestimate the true ionic conductivity of a given electrolyte. Holey graphene is a carbon nanomaterial with high electrical conductivity and unique dry compressibility, which is unusual for carbon materials but similar to many oxide and sulfide SEs. In this work, it is demonstrated that adding a thin layer of holey graphene between the electrolyte and the stainless steel current collectors significantly improves the interfacial contact. The ionic conductivity values obtained in the effort were sometimes several times higher than the data measured for SEs without the holey graphene layers. This work calls for more standardized measurement procedures to reduce the discrepancies in reported ionic conductivity values.

Solid state battery↗

Impact of Mixed Feedstocks and Feedstock Densification on Ionic Liquid Pretreatment Efficiency

Background: Lignocellulosic biorefineries must be able to efficiently process the regional feedstocks that are available at cost-competitive prices year round. These feedstocks typically have low energy densities and vary significantly in composition. One potential solution to these issues is blending and/or densifying the feedstocks in order to create a uniform feedstock. Results/discussion: We have mixed four feedstocks - switchgrass, lodgepole pine, corn stover, and eucalyptus - in flour and pellet form and processed them using the ionic liquid 1-ethyl-3-methylimidazolium acetate. Sugar yields from both the mixed flour and pelletized feedstocks reach 90% within 24 hours of saccharification. Conclusions: Mixed feedstocks, in either flour or pellet form, are efficiently processed using this pretreatment process, and demonstrate that this approach has significant potential.

09 BIOMASS FUELS↗

Reversible Bending Fatigue Test System for Investigating Vibration Integrity of Spent Nuclear Fuel during Transportation

Transportation packages for spent nuclear fuel (SNF) must meet safety requirements under normal and accident conditions as specified by federal regulations. During transportation, SNF experiences unique conditions and challenges to cladding integrity due to the vibrational and impact loading during road or rail shipment. Oak Ridge National Laboratory (ORNL) has been developing testing capabilities that can be used to improve the understanding of the impacts on SNF integrity due to vibration loading, especially for high burn-up SNF in normal transportation operation conditions. This information can be used to meet the nuclear industry and U.S. Nuclear Regulatory Commission needs in the area of safety and security of spent nuclear fuel storage and transport operations. The ORNL developed test system can perform reversible-bending fatigue testing to evaluate both the static and dynamic mechanical response of SNF rods under simulated loads. The testing apparatus is also designed to meet the challenges of hot-cell operation, including remote installation and detachment of the SNF test specimen, in-situ test specimen deformation measurement, and implementation of a driving system suitable for use in a hot cell. The system contains a U-frame set-up equipped with uniquely designed grip rigs, to protect SNF rod and to ensure valid test results, and use of 3 specially designed LVDTs to obtain the in-situ curvature measurement. A variety of surrogate test rods have been used to develop and calibrate the test system as well as in performing a series of systematic cyclic fatigue tests. The surrogate rods include stainless steel (SS) cladding, SS cladding with cast epoxy, and SS cladding with alumina pellets inserts simulating fuel pellets. Testing to date has shown that the interface bonding between the SS cladding and the alumina pellets has a significant impact on the bending response of the test rods as well as their fatigue strength. The failure behaviors observed from tested surrogate rods provides a fundamental understanding of the underlying failure mechanisms of the SNF surrogate rod under vibration which has not been achieved previously. The newly developed device is scheduled to be installed in the hot-cell in summer 2013 to test high burnup SNF.

high burn-up spent fuel↗

Plastic phase change material and articles made therefrom

The present invention generally relates to a method for manufacturing phase change material (PCM) pellets. The method includes providing a melt composition, including paraffin and a polymer. The paraffin has a melt point of between about 10.degree. C. and about 50.degree. C., and more preferably between about 18.degree. C. and about 28.degree. C. In one embodiment, the melt composition includes various additives, such as a flame retardant. The method further includes forming the melt composition into PCM pellets. The method further may include the step of cooling the melt to increase the melt viscosity before pelletizing. Further, PCM compounds are provided having an organic PCM and a polymer. Methods are provided to convert the PCM compounds into various form-stable PCMs. A method of coating the PCMs is included to provide PCMs with substantially no paraffin seepage and with ignition resistance properties.

25 ENERGY STORAGE↗

Production of LEU Fully Ceramic Microencapsulated Fuel for Irradiation Testing

Fully Ceramic Microencapsulated (FCM) fuel consists of tristructural isotropic (TRISO) fuel particles embedded inside a SiC matrix. This fuel inherently possesses multiple barriers to fission product release, namely the various coating layers in the TRISO fuel particle as well as the dense SiC matrix that hosts these particles. This coupled with the excellent oxidation resistance of the SiC matrix and the SiC coating layer in the TRISO particle designate this concept as an accident tolerant fuel (ATF). The FCM fuel takes advantage of uranium nitride kernels instead of oxide or oxide-carbide kernels used in high temperature gas reactors to enhance heavy metal loading in the highly moderated LWRs. Production of these kernels with appropriate density, coating layer development to produce UN TRISO particles, and consolidation of these particles inside a SiC matrix have been codified thanks to significant R&D supported by US DOE Fuel Cycle R&D program. Also, surrogate FCM pellets (pellets with zirconia instead of uranium-bearing kernels) have been neutron irradiated and the stability of the matrix and coating layer under LWR irradiation conditions have been established. Currently the focus is on production of LEU (7.3% U-235 enrichment) FCM pellets to be utilized for irradiation testing. The irradiation is planned at INL s Advanced Test Reactor (ATR). This is a critical step in development of this fuel concept to establish the ability of this fuel to retain fission products under prototypical irradiation conditions.

Terrani, Kurt A↗

A new hybrid genetic algorithm for optimizing the single and multivariate objective functions

In this work a new hybrid genetic algorithm was developed which combines a rudimentary adaptive steepest ascent hill climbing algorithm with a sophisticated evolutionary algorithm in order to optimize complex multivariate design problems. By combining a highly stochastic algorithm (evolutionary) with a simple deterministic optimization algorithm (adaptive steepest ascent) computational resources are conserved and the solution converges rapidly when compared to either algorithm alone. In genetic algorithms natural selection is mimicked by random events such as breeding and mutation. In the adaptive steepest ascent algorithm each variable is perturbed by a small amount and the variable that caused the most improvement is incremented by a small step. If the direction of most benefit is exactly opposite of the previous direction with the most benefit then the step size is reduced by a factor of 2, thus the step size adapts to the terrain. A graphical user interface was created in MATLAB to provide an interface between the hybrid genetic algorithm and the user. Additional features such as bounding the solution space and weighting the objective functions individually are also built into the interface. The algorithm developed was tested to optimize the functions developed for a wood pelleting process. Using process variables (such as feedstock moisture content, die speed, and preheating temperature) pellet properties were appropriately optimized. Specifically, variables were found which maximized unit density, bulk density, tapped density, and durability while minimizing pellet moisture content and specific energy consumption. The time and computational resources required for the optimization were dramatically decreased using the hybrid genetic algorithm when compared to MATLAB's native evolutionary optimization tool.

feedstock↗

Accident-tolerant oxide fuel and cladding

Systems and methods for accident tolerant oxide fuel. One or more disks can be placed between fuel pellets comprising UO.sub.2, wherein such disks possess a higher thermal conductivity material than that of the UO.sub.2 to provide enhanced heat rejection thereof. Additionally, a cladding coating comprising zircaloy coated with a material that provides stability and high melting capability can be provided. The pellets can be configured as annular pellets having an annulus filled with the higher thermal conductivity material. The material coating the zircaloy can be, for example, Zr.sub.5Si.sub.4 or another silicide such as, for example, a Zr-Silicide that limits corrosion. The aforementioned higher thermal conductivity material can be, for example, Si, Zr.sub.xSi.sub.y, Zr, or Al.sub.2O.sub.3.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Plastic phase change material and articles made therefrom

The present invention generally relates to a method for manufacturing phase change material (PCM) pellets. The method includes providing a melt composition, including paraffin and a polymer. The paraffin has a melt point of between about 10.degree. C. and about 50.degree. C., and more preferably between about 18.degree. C. and about 28.degree. C. In one embodiment, the melt composition includes various additives, such as a flame retardant. The method further includes forming the melt composition into PCM pellets. The method further may include the step of cooling the melt to increase the melt viscosity before pelletizing. Further, PCM compounds are provided having an organic PCM and a polymer. Methods are provided to convert the PCM compounds into various form-stable PCMs. A method of coating the PCMs is included to provide PCMs with substantially no paraffin seepage and with ignition resistance properties.

Abhari, Ramin↗

Resolution Limits of Near IR and IR Thermography Applied to Imaging Thermal Heterogeneities in Nuclear Fuel Surrogate Materials

ABSTRACT The main goal of the project is: To develop an IR thermographic method to monitor fuel pellet cracking inside the hostile environment of the nuclear core. This method will use a high temperature and radiation resistant fiber optic bundle to monitor the fuel pellet inside the core and transmit the information outside to an IR camera. This method will give a visual cue (using IR video) as to when the crack started to form and how it progresses. To achieve this goal, we identified the following as major milestones of the project: 1. Perform 1D modeling of temperature and blackbody radiation intensity across a crack. 2. Image a crack on a fuel cell surrogate using an IR camera with free-space optics and high power laser setup. 3. Simulate cracking in the surrogate sample through inductive heating method, and demonstrate imaging crack formation using the free-space optics setup. 4. Determine parameters for a suitable fiber optic bundle compatible with the IR camera based on the results from the free-space optics experiments. 5. Demonstrate imaging using fiber bundle and integrate viewing system with nuclear core at INL. This report focuses on Goals 1-3. We have successfully achieved Goals 1-3 and are making steady progress towards achieving Goals 4-9. Goals 2 and 4 are very similar and require 2 basic parts: the imaging system and the method to crack the fuel surrogate to replicate the fuel pellet cracking in the nuclear reactor core. The following sections describe the 1D modeling of temperature and blackbody radiation intensity across a crack (Goal 1), procedure to create crack on fuel surrogates and results (Goals 2 and 3), and the IR imaging system and results (Goal 2).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-irradiation Examinations of Accident Tolerant Fuel Candidates with Iron-alloy Cladding

A collaborative effort of the Advanced Fuels Campaign together with industry consortia is focused on the development of enhanced Accident Tolerant Fuels (ATF) for Light Water Reactors (LWRs). The scoping studies, referred to as ATF 1 irradiations, are being performed in the Advanced Test Reactor of Idaho National Laboratory using drop-in style irradiations. The Post Irradiation Examinations (PIEs) of ATF-1 began in 2017 and continued in 2019. This report describes the results of examinations on ATF-1 irradiations designed to test the performance of iron-based cladding. Two rodlets with commercial iron-based cladding and UO2 pellets have been irradiated to low burnup (i.e., < 20 GWd/tHM). The first rodlet had an Alloy33® cladding, while the other had a Kanthal APMT® cladding. The performed PIEs were focused on the determination of fuel microstructure, evaluation of fuel cladding interaction and irradiation-induced variations of cladding mechanical properties. For both rodlets, no significant changes in the cladding hardness were measured, and the cladding hoop strain remained limited. Gamma tomography revealed no Cs axial migration as expected for LWR fuel, but significant cesium radial migration, which was induced by thermal migration consequent to high irradiation temperatures compared to standard LWR irradiation temperatures. Microstructure analyses revealed formation of secondary phases along the pellet rim of samples from both rodlets. No wastage or extensive chemical interaction between the fuel and the internal wall of the cladding was observed, suggesting that the secondary phases accumulated at the pellet rim might be due to formation of Cs-U-O compounds. However, further advanced PIEs are necessary to confirm this hypothesis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

In-Pile Loss of Coolant Accident Testing at TREAT

Several hot-cell based LOCA test apparatuses still exist in various institutions across the world. These facilities typically surround rods with infrared electrical heaters to simulate LOCA conditions on the cladding. Despite its utility for cladding-focused testing, the furnace-based external heating method creates an inverted temperature gradient in fuel pellets compared to a true LOCA where radioisotope decay heat generates internal heat. Capturing the correct temperature gradient is essential in simulating the thermomechanical stress in fuel pellets, and hence a crucial design parameter investigating FFRD during a postulated LOCA. This thermomechanical stress state, for which the evolution of fuel pellet centerline and cladding temperatures is a good figure of merit, was the primary parameter investigated during conception of the LOCA-SERTTA device.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Method of manufacturing a reinforced nuclear fuel cladding using an intermediate thermal deposition layer

A method is described that includes the steps of making a thin walled Zr alloy tube, loading nuclear fuel pellets into the tube, compressing the tube onto the fuel pellets to substantially reduce free space around the fuel pellets, positioning end plugs at each of two ends of the tube, filling the tube with a heat transferring gas, and coating the compressed tube with a corrosion resistant material using a thermal deposition process, such as cold spray, before inserting the tube into a pre-formed SiC composite cover having at least one closed end.

Lahoda, Edward J.↗

AREVA enhanced accident tolerant fuel program - Current results and future plans

The purpose of this paper is to provide a brief overview of the enhanced accident tolerant fuel (EATF) concepts investigated by the AREVA team in Phase 1 to support the U.S Department of Energy Enhanced Accident Tolerant Fuel program and concerning light water reactors. The main goal of the 'fuel pellets with additive' concept is to improve the economics, performance and operational flexibility of fuel in light water reactors while featuring improved safety performance under normal and off-normal conditions. Within this concept 2 nuclear fuels were explored: Cr{sub 2}O{sub 3} doped UO{sub 2} pellet and composite UO{sub 2} pellets. The second concept is the coating of zirconium cladding whose main goal is to reduce cladding oxidation and hydrogen generation during accident conditions. The coating materials were chosen to be compatible with the specific deposition process, to provide robustness in the nuclear environment and have a relatively small neutron cross section. Three coatings were explored: chromium coated claddings, electrophoretic deposition of coating, and MAX phase coatings. MAX phases are a family of the layered compounds with a general formula M{sub n+1}AX{sub n} with n = 1, 2, or 3, where M is a transition metal, A is an A-group element, and X is either C or N. Another improvement to the fuel cladding that was considered is to replace the zirconium cladding altogether with an alternative cladding material which can substantially improve reactor response during postulated accident conditions. Two concepts were investigated: molybdenum claddings and SiC/SiC composite cladding.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Proven Uranium Recovery Solutions for the Nuclear Fuel Manufacturing Market - 16060

During the Nuclear Fuel Manufacturing process a number of by-products and residues are generated from various sources. In recent years, Westinghouse has characterised and processed around 50,000 drums of residue comprising of numerous different types generated over 60 years from the manufacture of numerous types of fuel for greater than 50 reactors. These include, AGR, Magnox (uranium metal fuel), PWR, fast reactors and various test reactors. Different organisations have different definitions and names for each of these categories but essentially they fall into one of the following categories: Clean Scrap (U{sub 3}O{sub 8}, UO{sub 2}, UO{sub 3}, UF{sub 4}, powders, pellets), Dirty Scrap (U{sub 3}O{sub 8}, UO{sub 2}, UO{sub 3}, UF{sub 4}, powders, pellets), Gd Contaminated Scrap (U{sub 3}O{sub 8}, UO{sub 2}, powders, pellets), Ash, Sludge, Combustible / soft residues (e.g. ventilation filters, gloves, plastic bags), Contaminated metals (including contaminated scrap zirconium tubes), Materials arising from decommissioning. Routes have been developed across the industry for a number of the categories listed above, however in numerous examples, routes have not been established and materials have been stored creating a significant legacy. Westinghouse understands the issues regarding legacy uranic material and the financial and regulatory impact of storage. Interim storage of materials may seem like a low cost option in the short term; however ongoing costs for facilities, manpower and equipment, without a permanent and final solution can result in significant lifetime material management costs. Recovery of uranium and sending materials for safe disposal of enriched uranium residues is not easy because of the criticality risk both during processing and at a disposal site. Therefore quantities of materials than can be sent via permitted disposal routes are very limited The development of regulations often means that finding solutions is becoming more difficult. It is believed that timely resolution is ultimately the most cost effective solution. In addition, the intrinsic value of recycling this material is also high and in some cases can mitigate the cost of processing. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Post-Transient Examination Results of RIA Commissioning Teats at the Transient Reactor Test Facility

Six reactivity-initiated-accident (RIA) commissioning tests have been performed at Idaho National Laboratory’s (INL) Transient Reactor Test Facility. Five of these tests were performed using fresh fuel rodlets, and the sixth test was performed using a previously irradiated rodlet from the ATF-2 irradiation experiment. These experiments demonstrate the ability to perform RIA testing including the ability to perform experiments using previously irradiated materials. Post-transient examinations revealed pellet cladding interactions and cladding ballooning depending on the initial boundary conditions of the test. Increased thickness of both zirconium oxide and alpha-zirconium were found in the cladding with tests performed at higher levels of total energy deposition. No oxide or alpha-zirconium was found in the test with the greatest amount of ballooning, which was also the test with the highest initial rod internal pressure. The highest energy deposition test (1110 J/g) resulted in failure of the rodlet. Fragmentation of the fuel pellets occurred in this test with the size of the fragments decreasing inversely to the pellet radius.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Dietary cadmium and benzo(a)pyrene increased intestinal metallothionein expression in the fish Fundulus heteroclitus

To test the effect of dietary exposure to cadmium and benzo(a)pyrene on induction of metallothionein mRNA in the Fundulus heteroclitus, fish were individually fed a pelletized gel food containing cadmium, benzo(a)pyrene, or a combination of the two over a period of seven days, then analyzed for relative levels of metallothionein mRNA in the intestine, liver, and gill using real-time RT-qPCR. An initial experiment with only cadmium exposure showed an apparent 10-fold induction in the intestine, but no induction in liver or gill. Ingestion of contaminated pellets varied in individual fish, and because it was possible to monitor individual ingestion rates with our method, individual cadmium doses were estimated from the amount of ingested cadmium. When the levels of metallothionein mRNA were related to the dose to each fish, a linear dose-response relationship was observed for the intestine, but not the other organs, which showed no induction. In a second experiment, dose was controlled by placing the entire daily cadmium dose into a single contaminated pellet that was fed first (thereby, effectively controlling the effect of variable ingestion rates), and the interaction between cadmium and benzo(a)pyrene was also investigated. The intestine was again the primary organ for metallothionein induction by cadmium, with a 20-fold increase in metallothionein mRNA over control levels. When benzo(a)pyrene was administered together with cadmium, induction of metallothionein was potentiated by the presence of benzo(a)pyrene, with the main effect seen in the intestine, where already high levels of induction by cadmium alone increased by 1.74-fold when benzo(a)pyrene was present.

59 BASIC BIOLOGICAL SCIENCES↗

Time-Dependent Diffusion Coefficient of Fe in MgB{sub 2} Superconductors

The iron (Fe) diffusion in superconducting MgB{sub 2} bulk samples has been studied for sintering time durations of 15 min, 30 min, 1 h, 2 h, and 4 h at 900{sup ∘}C. Fe coating bulk polycrstalline superconducting MgB{sub 2} samples for Fe coating were prepared by pelletizing and used in the diffusion experiments with initial sintering at 800{sup ∘}C for 1 h. A thin layer of Fe was coated on MgB{sub 2} pellets by evaporation in vacuum. Effects of Fe diffusion on the structural, electrical, and superconducting properties of MgB{sub 2} have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), infrared spectroscopy (IR), energy-dispersive X-ray spectroscopy (EDS), and resistivity measurements. Fe diffused samples have slightly increased critical transition temperatures and have larger lattice parameter c values, in comparison with bare samples. Fe diffusion coefficients were calculated from depth profiles of c parameter and room temperature resistivity values. Depth profiles were obtained by successive removal of thin layers from Fe diffused surfaces of the samples. Our results have shown that the Fe diffusion coefficient decreases with increasing sintering time and resistivity measurements can be utilized for determination of diffusion coefficient.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Cr2O3 on the O-18 Tracer Incorporation in SOFC Materials

To gain insight into the Cr poisoning mechanism at the cathode side of solid oxide fuel cells (SOFCs) with stainless steel interconnects, we conducted an investigation of the impact of Cr2O3 overlayers on oxygen diffusion in various SOFC electrolyte and cathode materials. High density Gd0.10Ce0.90O2 (GDC), Y0.15Zr0.85O2 (YSZ) and La0.6Sr0.4Co0.2Fe0.8O2 (LSCF) sintered pellets were covered with 3 to 30 nm Cr - overlayers that were subsequently oxidized, forming Cr2O3. Standard 18O tracer diffusion experiments at 800°C were performed and TOFSIMS profiling revealed a Cr2O3 thickness-dependent oxygen uptake process. The oxygen ion diffusion coefficients were found to be unaffected by the Cr2O3 overlayers, which is predictable since they are a bulk property. The extracted surface exchange coefficients however varied with Cr2O3 overlayer thickness. Solid state reaction measurements of Cr2O3 with the three materials of interest, and electronic structure considerations concerning the surface exchange, led to the conclusion that the observed oxygen uptake hindrance for LSCF and the slight increase of the surface exchange coefficient for YSZ can be attributed to the electronic properties of Cr2O3. The rate limitation of the oxygen incorporation into the materials is therefore strongly dependent on the surface electronic properties. A critical thickness of Cr2O3 was determined where the transition from decreased cathode-performance to a Cr2O3-property-governed regime occurs.

30 DIRECT ENERGY CONVERSION↗