Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Mixture design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Driving of combustor oscillations by gaseous propellant injectors

Measurements of reactive admittances that describe the capabilities of the combustion processes associated with coaxial gaseous fuel injectors to amplify combustor oscillations are presented. These admittances are needed in (1) stability analyses of rocket motors and gas turbine combustors; (2) for the evaluation of 'driving' capabilities of injectors; and (3) for checking the applicability of a theoretical model. The modified standing-wave technique was used to determine the admittances of the combustion processes in coaxial injectors utilizing air-acetylene mixtures. The measurements indicated that (1) coaxial injectors can sustain combustion instabilities over wide frequency ranges; (2) the maximum driving capability of an injector decreases with an increased equivalence ratio; (3) the frequency at which maximum driving is observed decreases with the increased equivalence ratio; and (4) the characteristic combustion time of an injector design decreases with increased frequency.

Janardan, B. A.↗
NASA NTRS2013

Vaporization and Zonal Mixing in Performance Modeling of Advanced LOX-Methane Rockets

Initial modeling of LOX-Methane reaction control (RCE) 100 lbf thrusters and larger, 5500 lbf thrusters with the TDK/VIPER code has shown good agreement with sea-level and altitude test data. However, the vaporization and zonal mixing upstream of the compressible flow stage of the models leveraged empirical trends to match the sea-level data. This was necessary in part because the codes are designed primarily to handle the compressible part of the flow (i.e. contraction through expansion) and in part because there was limited data on the thrusters themselves on which to base a rigorous model. A more rigorous model has been developed which includes detailed vaporization trends based on element type and geometry, radial variations in mixture ratio within each of the "zones" associated with elements and not just between zones of different element types, and, to the extent possible, updated kinetic rates. The Spray Combustion Analysis Program (SCAP) was leveraged to support assumptions in the vaporization trends. Data of both thrusters is revisited and the model maintains a good predictive capability while addressing some of the major limitations of the previous version.

Williams, George J., Jr.↗
NASA NTRSDate not supplied

Selection, Production, and Properties of Regolith Polymer Composites for Lunar Construction

NASA’s Artemis Program seeks to establish a long-term presence on the Moon to enable scientific exploration and expand the cis-lunar economy by utilizing lunar resources through public-private and international partnerships. Over the next decades, a lunar spaceport will need to be established to provide the services and facilities that are necessary to achieve this goal. Robotic construction technologies using in-situ materials must be developed to build up enabling infrastructure such as launch/landing pads, blast protection, power/communications infrastructure, improved roads, improved operational surfaces, and radiation protection shelters. Kennedy Space Center’s Granular Mechanics and Regolith Operations laboratory at Swamp Works has partnered with SpaceFactory and LERA Consulting Structural Engineers to develop the architectural and structural design of an unpressurized lunar shelter. The shelter, called Lunar Infrastructure Asset (LINA), is designed to support 2.3 m of regolith overburden to protect astronauts and surface assets from radiation, meteoroid impact, thermal gradients/cycling, and to withstand moonquakes. LINA’s structural design criteria and the resulting structure design are detailed in separate papers. A Fused Filament Fabrication (FFF) construction process using regolith polymer composites has been developed and is detailed in a separate publication. This paper presents material formulations and selection rationale for each of the composite components that were examined. Formulations include 70:30, 80:20, and 85:15 wt.% mixture ratios of lunar mare simulant Black Point-1 (BP-1): Polylactic Acid (PLA), 80:20 Lunar Highlands Simulant-1 (LHS-1): PLA and an 80:20 BP-1: PLA formulation with a flow enhancer additive. Test samples were printed in simulated lunar dirty thermal vacuum conditions (-190 °C, 10-3 torr). A series of tests were performed on each formulation to characterize the achieved mixture ratio, mechanical strength properties, off-gassing products during vacuum printing, and porosity and density of printed products. The LHS-1: PLA formulation yielded an advantageous combination of properties and was used in a final test that additively constructed a sub-scaled LINA on regolith simulant in dirty vacuum conditions. The materials and construction process presented in this paper are considered to be at Technology Readiness Level (TRL) 5 with additional testing necessary to characterize long term lunar environmental exposure effects.

lunar infrastructure↗
NASA NTRS2014

A Design of Experiments Investigation of Offset Streams for Supersonic Jet Noise Reduction

An experimental investigation into the noise characteristics of a dual-stream jet with four airfoils inserted in the fan nozzle was conducted. The intent of the airfoils was to deflect the fan stream relative to the core stream and, therefore, impact the development of the secondary potential core and noise radiated in the peak jet-noise direction. The experiments used a full-factorial Design of Experiments (DoE) approach to identify parameters and parameter interactions impacting noise radiation at two azimuthal microphone array locations, one of which represented a sideline viewing angle. The parameters studied included airfoil angle-of-attack, airfoil azimuthal location within the fan nozzle, and airfoil axial location relative to the fan-nozzle trailing edge. Jet conditions included subsonic and supersonic fan-stream Mach numbers. Heated jets conditions were simulated with a mixture of helium and air to replicate the exhaust velocity and density of the hot jets. The introduction of the airfoils was shown to impact noise radiated at polar angles in peak-jet noise direction and to have no impact on noise radiated at small and broadside polar angles and to have no impact on broadband-shock-associated noise. The DoE analysis showed the main effects impacting noise radiation at sideline-azimuthal-viewing angles included airfoil azimuthal angle for the airfoils on the lower side of the jet near the sideline array and airfoil trailing edge distance (with airfoils located at the nozzle trailing edge produced the lowest sound pressure levels). For an array located directly beneath the jet (and on the side of the jet from which the fan stream was deflected), the main effects impacting noise radiation included airfoil angle-of-attack and airfoil azimuthal angle for the airfoils located on the observation side of the jet as well and trailing edge distance. Interaction terms between multiple configuration parameters were shown to have significant impact on the radiated noise. The models were shown to adequately describe the sound-pressure levels obtained for a configuration in the center of the design space indicating the models can be used to navigate the design space.

Jet Noise↗
DOE OSTI2022

Mechanistic study of chemical looping reactions between solid carbon fuels and CuO

Copper (Cu) based chemical-looping combustion (CLC) is a promising process that utilizes solid carbon fuel such as coal and biomass. Understanding the reaction kinetics in this process can facilitate the industrial design of CLC units. Here, in this work, molecular dynamics (MD) simulations were performed to investigate the reaction kinetics of n-butane and two simplified solid carbon fuels (lignite and anthracite) with/without copper oxide (CuO) nanoparticle. In addition, experiments were conducted on the thermal characteristics, flammability, and flame speeds of CuO and solid carbon mixtures. For n-butane, oxidation on the CuO surface is the primary reaction since the activation energy of the surface reaction is much lower than that of oxygen (O 2 ) combustion (9.2 vs. 53.3 kcal/mol). On the other hand, for lignite, there is a smaller difference in the activation energy of O 2 combustion and surface reaction (23.04 vs. 6.34 kcal/mol). We hypothesize that some solid carbon fuels can have different reaction kinetics dependent upon temperature. This is proven by the case of a simplified anthracite coal: an Arrhenius plot shows that this solid carbon fuel has two different reaction kinetic regimes and the critical temperature for the change in kinetics is related to the oxygen uncoupling of the CuO nanoparticle. Like the modeling simulations, a change in activation energy is observed in the experimental results, where desorption of molecular oxygen from CuO becomes important.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Nonlinear models for coupling the effects of stimulated Raman scattering to inertial confinement fusion codes

Laser plasma instabilities (LPI) reduce driver-target coupling, alter implosion symmetry, and therefore can fundamentally limit fusion performance in inertial confinement fusion (ICF). Developing a predictive modeling capability for LPI effects can critically advance the success of the field. We perform vector particle-in-cell simulations of multi-speckled laser beams undergoing stimulated Raman scattering (SRS) at various densities and intensities relevant to mainly indirectly driven and a subset of parameter space for directly driven ICF systems, focusing on the regimes with intensities above the onset of electron trapping. Based on the wavenumber of the SRS daughter electron plasma wave, we identify several regions with underpinning SRS saturation physics: the electron-trapping dominated region with intermediate kλD values, the strong Landau damping region at larger kλD values, and the region where the Langmuir decay instability arises at lower kλD values. We develop a nonlinear SRS reflectivity model that features the base trapping-dominated scaling of (kλD)−4 and its modifications. Electron trapping deforms the initialized electron distribution functions, and we have developed a new δf-Gaussian-mixture algorithm for an accurate characterization of the trapped hot electron population. With this SRS hot electron description, we construct a nonlinear energy deposition model and a hot electron source model—based on a modified Manley–Rowe relation—suitable for including SRS effects as a sub-grid module in a high-fidelity ICF design code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Machine learning-accelerated discovery of iron cobalt phosphides as rare-earth-free magnets

Here, the discovery of rare-earth-free permanent magnets has been a goal of scientists for decades. The absence of rare-earth elements will alleviate a pressing concern about the availability of rare-earth elements used in permanent magnets. These magnets are crucial for applications such as wind turbines, electric cars, and memory devices. Rare-earth magnets are special owing to a large magnetic anisotropy energy (K 1 ). In contrast, iron cobalt phosphides hold promise since doping P into cubic FeCo can induce anisotropy, leading to a large coercivity, without introducing rare-earth elements. We present a comprehensive search over the Fe-Co-P ternary space for magnets, utilizing recently developed adaptive machine learning feedback to efficiently screen over 850 000 structures. We focus on machine learning acceleration as a paradigm for materials design. Further adaptive genetic algorithm searches and first-principles calculations aid in the identification of 16 new structures below the known convex hull. Five of them possess high magnetic polarization (J s > 1 T). The structures with desirable magnetic properties center on (Fe,Co) 2⁢ P. This supports conventional wisdom, which focuses on the mixture of the two known end compounds: Fe 2 ⁢P and Co 2 ⁢P. Our work provides guidance for synthesis. We find Fe 7 ⁢CoP 4 shows the most promise (J s = 1.03T and K 1 = 0.83MJ/m 3 ).

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive-Mixing Fuel Injection (AMFI): A device for robust control and improved performance of high-efficiency LTGC engines

Low-temperature gasoline combustion (LTGC) engines can provide high efficiencies with very low NOx and particulate emissions. Despite these major advantages, methods for controlling LTGC combustion timing, achieving robust autoignition, and good low-load performance have challenged the development of practical LTGC engines. A key reason is that the ideal reactivity of the fuel varies with operating conditions, with low-reactivity fuels working well at high loads and higher-reactivity fuels working better at low loads. This article introduces a new technique called Additive Mixing Fuel Injection (AMFI) that adjusts the reactivity of the gasoline to obtain good performance over the operating map. Moreover, AMFI can provide robust combustion-timing control because it precisely meters very small amounts (0.01–0.6 mm 3 ) of an ignition-enhancing additive into the fuel each engine cycle. The additive used was 2-ethylhexyl nitrate (EHN), a common, inexpensive diesel-fuel ignition improver, but other additives could be used. Because additive amounts are so small, a 2-gal reservoir would be sufficient for medium-duty applications with refilling only at service intervals of about 8000 mi. The AMFI system has been installed on a single-cylinder LTGC research engine and demonstrated to provide robust combustion-timing control over wide ranges of combustion phasing, fueling rate, intake boost, engine speed, and intake temperature. AMFI also increases the fuel’s reactivity sufficiently to greatly reduce or eliminate the need for charge heating, simplifying engine design and significantly increasing thermal efficiency and the maximum load at low-boost conditions. The nitrogen in the EHN produced a modest increase in NOx, but it was mitigated by lower intake temperatures, and NOx emissions remained very low. Finally, the additive increases the sensitivity of autoignition reactions to variations in the local fuel/air mixture within the charge. This allows the use of controlled fuel stratification for improved LTGC-engine performance, and its potential to improve low-load operation was demonstrated.

Dec, John E.↗
NASA NTRS1992

Advanced Raman water vapor lidar

Water vapor and aerosols are important atmospheric constituents. Knowledge of the structure of water vapor is important in understanding convective development, atmospheric stability, the interaction of the atmosphere with the surface, and energy feedback mechanisms and how they relate to global warming calculations. The Raman Lidar group at the NASA Goddard Space Flight Center (GSFC) developed an advanced Raman Lidar for use in measuring water vapor and aerosols in the earth's atmosphere. Drawing on the experience gained through the development and use of our previous Nd:YAG based system, we have developed a completely new lidar system which uses a XeF excimer laser and a large scanning mirror. The additional power of the excimer and the considerably improved optical throughput of the system have resulted in approximately a factor of 25 improvement in system performance for nighttime measurements. Every component of the current system has new design concepts incorporated. The lidar system consists of two mobile trailers; the first (13m x 2.4m) houses the lidar instrument, the other (9.75m x 2.4m) is for system control, realtime data display, and analysis. The laser transmitter is a Lambda Physik LPX 240 iCC operating at 400 Hz with a XeF gas mixture (351 nm). The telescope is a .75m horizontally mounted Dall-Kirkham system which is bore sited with a .8m x 1.1m elliptical flat which has a full 180 degree scan capability - horizon to horizon within a plane perpendicular to the long axis of the trailer. The telescope and scan mirror assembly are mounted on a 3.65m x .9m optical table which deploys out the rear of the trailer through the use of a motor driven slide rail system. The Raman returns from water vapor (403 nm), nitrogen (383 nm) and oxygen (372 nm) are measured in addition to the direct Rayleigh/Mie backscatter (351). The signal from each of these is split at about a 5/95 ratio between two photomultiplier detectors. The 5 percent detector is used for measurements below about 4.0 km, while the 95 percent detector provides the information above this level.

Whiteman, David N.↗
NASA NTRS1994

Optimization of Orifice Geometry for Cross-Flow Mixing in a Cylindrical Duct

Mixing of gaseous jets in a cross-flow has significant applications in engineering, one example of which is the dilution zone of a gas turbine combustor. Despite years of study, the design of jet injection in combustors is largely based on practical experience. A series of experiments was undertaken to delineate the optimal mixer orifice geometry. A cross-flow to core-flow momentum-flux ratio of 40 and a mass flow ratio of 2.5 were selected as representative of an advanced design. An experimental test matrix was designed around three variables: the number of orifices, the orifice aspect ratio (long-to-short dimension), and the orifice angle. A regression analysis was performed on the data to arrive at an interpolating equation that predicted the mixing performance of orifice geometry combinations within the range of the test matrix parameters. Results indicate that mixture uniformity is a non-linear function of the number of orifices, the orifice aspect ratio, and the orifice angle. Optimum mixing occurs when the asymptotic mean jet trajectories are in the range of 0.35 less than r/R less than 0.5 (where r = 0 is at the mixer wall) at z/R = 1.0. At the optimum number of orifices, the difference between shallow-angled slots with large aspect ratios and round holes is minimal and either approach will lead to good mixing performance. At the optimum number of orifices, it appears possible to have two local optimums where one corresponds to an aspect ratio of 1.0 and the other to a high aspect ratio.

Sowa, W. A.↗
NASA NTRS2012

Experimental Modeling of Sterilization Effects for Atmospheric Entry Heating on Microorganisms

The objective of this research was to design, build, and test an experimental apparatus for studying the parameters of atmospheric entry heating, and the inactivation of temperature-resistant bacterial spores. The apparatus is capable of controlled, rapid heating of sample coupons to temperatures of 200 to 350 C and above. The vacuum chamber permits operation under vacuum or special atmospheric gas mixtures.

Schubert, Wayne W.↗
NASA NTRS2013

Piezoelectrically Initiated Pyrotechnic Igniter

This innovation consists of a pyrotechnic initiator and piezoelectric initiation system. The device will be capable of being initiated mechanically; resisting initiation by EMF, RF, and EMI (electromagnetic field, radio frequency, and electromagnetic interference, respectively); and initiating in water environments and space environments. Current devices of this nature are initiated by the mechanical action of a firing pin against a primer. Primers historically are prone to failure. These failures are commonly known as misfires or hang-fires. In many cases, the primer shows the dent where the firing pin struck the primer, but the primer failed to fire. In devices such as "T" handles, which are commonly used to initiate the blowout of canopies, loss of function of the device may result in loss of crew. In devices such as flares or smoke generators, failure can result in failure to spot a downed pilot. The piezoelectrically initiated ignition system consists of a pyrotechnic device that plugs into a mechanical system (activator), which on activation, generates a high-voltage spark. The activator, when released, will strike a stack of electrically linked piezo crystals, generating a high-voltage, low-amperage current that is then conducted to the pyro-initiator. Within the initiator, an electrode releases a spark that passes through a pyrotechnic first-fire mixture, causing it to combust. The combustion of the first-fire initiates a primary pyrotechnic or explosive powder. If used in a "T" handle, the primary would ramp the speed of burn up to the speed of sound, generating a shock wave that would cause a high explosive to go "high order." In a flare or smoke generator, the secondary would produce the heat necessary to ignite the pyrotechnic mixture. The piezo activator subsystem is redundant in that a second stack of crystals would be struck at the same time with the same activation force, doubling the probability of a first strike spark generation. If the first activation fails to ignite, the device is capable of multiple attempts. Another unique aspect is in the design of the pyrotechnic device. There is an electrode that aids the generation of a directed spark and the use of a conductive matrix to support the first-fire material so that the spark will penetrate to the second electrode.

Quince, Asia↗
DOE OSTI2024

Hydrogen Leak Modeling for Development of Smart Distributed Monitoring Under Unintended Releases

Hydrogen is a versatile and clean energy carrier that can be produced from various renewable sources such as wind, solar, and hydropower. Hydrogen has the potential to play a crucial role in decarbonizing industrial processes that are currently reliant on fossil fuels and provide long-duration and/or seasonal energy storage to enable electricity decarbonization. Hydrogen can also be used as a fuel for fuel cell vehicles, providing a zero-emission alternative to traditional internal combustion engines. DOE launched the Hydrogen Energy Earthshot (Hydrogen Shot) in June 2021 to reduce the cost of clean hydrogen by 80% to $1 per 1 kilogram in 1 decade ("1 1 1"). While promising, Hydrogen is highly-flammable, and in the presence of oxygen, it can form explosive mixtures. . Therefore, understanding leak scenarios is essential to evaluate and mitigate the safety risks associated with potential hydrogen leaks. An increased understanding of leak behavior, and having tools to model leaks, can help assess how hydrogen would disperse in different environments, influencing emergency response plans and safety measures, and identify potential issues with materials and design systems that can withstand the challenges posed by hydrogen. Recently, researchers have attempted to study hydrogen leaks for development of risk management strategies. However, the focus has been on closed or semi-closed spaces like storage rooms, vehicles, garages, and fueling stations - all promising locations for future hydrogen infrastructure. In this presentation, the modeling environment extends the span of research further by modeling hydrogen leak in an outdoor, open space. We will present the key challenges with modeling hydrogen leaks in an uncontrollable environment, how they were handled, and how modeling results informed sensor selection and placement. A Hydrogen research facility at the National Renewable Energy Laboratory (NREL) was used as a case study to model hydrogen leaks. In the future, Hydrogen wide area detection methodologies will be developed and tested at this site to monitor for unintended and operational hydrogen releases. The data generated from modeling will be used to develop a predictive model to detect hydrogen leak location based on concentration measured by sensors in this open space. Furthermore, the facility was also chosen because controlled hydrogen releases can be performed. A computational fluid dynamics (CFD) based modeling approach was taken to model hydrogen leak. The full-scale hydrogen facility was modeled with a large ambient domain. The electrolyzer at the facility can produce a controlled release rate of 27 kg-H2/hr. Site-specific atmospheric and weather condition data such as wind direction, wind speed at various altitudes, and temperature were used as inputs to the model. To capture the variability of weather conditions, a subset of the weather conditions experienced during daytime hours without precipitation over the course of three months was generated; using established data clustering techniques, a total of 100 condition sets were chosen. The results show statistical distributions and ranges of hydrogen concentrations at locations throughout the domain. These distributions are compared to experimental data from a constant mass flow, controlled hydrogen release at the facility. The stochastic wind conditions of the release make direct validation difficult, therefore, statistical comparison approaches were used. Wind conditions are found to significantly impact the release behavior, including direction and concentration. Sensor selection and placement is proposed for the facility and is now based on release behavior predicted for the facility given its weather patterns; this is much more informed than without the modeling results. The methodology and analysis procedure can be translated to other facilities using modified geometries and site-specific weather conditions. Hydrogen holds great promise as a renewable energy fuel, but ensuring safety in its production, storage, and use is paramount. Studying potential leak scenarios in an open space will help develop sensors to detect hydrogen on a large spectrum of concentration and eventually build a smart distributed monitoring system.

CFD↗
DOE OSTI2020

Solvent Selection for the Separation of Lignin-Derived Monomers Using the Conductor-like Screening Model for Real Solvents

The separation of desired monomers from a liquid-phase mixture of lignin depolymerization products is necessary to facilitate their upscaling and upgrading for industrial applications. One effective method to separate multiple liquid-phase products is countercurrent chromatography (CCC), which is a common liquid chromatography technique that separates target solutes based on differences in their partitioning in a biphasic solvent system. Effective CCC separation requires the selection of solvent compositions to tune solute partition coefficients. Here, to alleviate the experimental burden of selecting optimal solvent systems, we apply the conductor-like screening model for real solvents (COSMO-RS) method to compute partition coefficients of representative lignin monomers from four currently used depolymerization strategies in standard solvent systems. We further design new ternary and quaternary solvent systems that are predicted to further improve separation efficacy. On the basis of these predicted partition coefficients and empirical solvent selection criteria for CCC measurements, we suggest a range of solvent systems that would be suitable for the effective separation of aromatic lignin-derived products via CCC or similar liquid–liquid extraction methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Solvent absorption rate of perfluorosulphonic acid membranes towards understanding direct coating processes

Here we present a method for measurement of the rate of solvent absorption by perfluorosulfonic acid (PFSA) membranes using a force tensiometer. The method presented here can be used as a tool to understand solvent absorption and should provide a rationale for designing catalyst inks for direct coating processes since it is necessary to understand how the absorption rate – on a time scale of seconds to minutes – compares to the time scales of the coating process in order to minimize membrane swelling. This method allows for rapid screening of the absorption and swelling behavior of different solvents and mixtures. Using this method, the absorption of water/1-propanol mixtures were measured for three thicknesses of Nafion PFSA membrane – Nafion 1135, Nafion 115, and Nafion 117. We find that the absorption rate is dependent on the ratio of the solvents as well as the thickness of the membrane. The analysis indicates that the highest absorption rate occurs when the mass percentage of 1-propanol in the mixture is 50%, whereas the lowest rates are for pure water and 1-propanol. In addition, membrane distortion also occurs most quickly for the 50% 1-propanol mixture. Our results suggest that catalyst inks that are highly rich (=90%) in water or 1-propanol are likely best for direct coating as such formulations will minimize absorption and swelling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Linking water quality, fouling layer composition, and performance of reverse osmosis membranes

Fouling of polyamide membranes during reverse osmosis (RO) is a major challenge for adopting membrane technologies to treat highly contaminated waters, especially those containing organic foulants (e.g., natural organic matter (NOM), polysaccharides) and dominant cations (e.g., sodium, magnesium, calcium). Here, this work combines bench-scale membrane fouling experiments with detailed characterization of feedwater chemistry and fouling layer composition/morphology to reveal fundamental mechanisms of (in)organic fouling during RO. Divalent cations are shown to promote fouling by hydrophobic NOM containing aromatic and carboxyl groups, while NOM fouling in the presence of a monovalent cation, sodium, occurs by smaller fulvic acids containing larger fractions of carboxyl groups and other oxygen-rich moieties. Calcium-carboxyl bridging occurs in solution and near the membrane surface to induce NOM aggregation on nanometer length scales. In complex waters containing foulant mixtures, co-fouling by calcium-carboxyl bridging and CaCO 3 precipitation influence membrane performance at longer timeframes. However, the flux decline observed for the co-fouling mechanism was less significant than the sum of its parts, suggesting both synergistic and antagonistic fouling mechanisms should be considered in membrane design/operation. These results encourage the design of pretreatment processes to reduce concentrations of multivalent ions and hydrophobic NOM in RO feedwaters, and of membrane materials to limit attachment/deposition of aggregates to/on polyamide surfaces.

42 ENGINEERING↗
NASA NTRS1979

Phase 1 of the First Small Power System Experiment (engineering Experiment No. 1). Volume 3: Experimental System Descriptions

The design and development of a modular solar thermal power system for application in the 1 to 10 MWe range is described. The system consists of five subsystems: the collector, power conversion, energy transport, energy storage, and the plant control subsystem. The collector subsystem consists of concentrator, receiver, and tower assemblies. The energy transport subsystem uses a mixture of salts with a low melting temperature to transport thermal energy. A steam generator drives a steam Rankine cycle turbine which drives an electrical generator to produce electricity. Thermal and stress analysis tests are performed on each subsystem in order to determine the operational reliability, the minimum risk of failure, and the maintenance and repair characteristics.

Holl, R. J.↗