Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material degradation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Performance of Vehicle Fuel System Elastomers and Plastics with Test Fuels Representing Gasoline Blended with 10% Ethanol (E10) and 16% Isobutanol (iBu16)

The compatibilities of fuel system elastomers and plastics were evaluated for test fuels containing 16 vol.% isobutanol (iBu16) and 10 vol.% ethanol (E10). Elastomers included two fluorocarbons, four acrylonitrile butadiene rubbers (NBRs), and one type of fluorosilicone, neoprene, and epichlorohydrin/ethylene oxide. Plastic materials included four nylon grades, three polyamides, polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), ethylene tetrafluoroethylene (ETFE), polyphenylene sulfide (PPS), high-density polyethylene (HDPE), polybutylene terephthalate (PBT), polyoxymethylene (POM), flexible polyvinylchloride (PVC), polyetherimide (PEI), polyetheretherketone (PEEK), and a phenol formaldehyde reinforced with glass fiber (GFPF). For each polymer material, the volume, mass, and hardness were measured before and after drying. Dynamic mechanical analysis (DMA) measurements were also performed on the dried specimens.For the elastomer materials the measured properties were similar for both fuels. The fluorocarbons and fluorosilicone swelled the least (~20%), while more moderate (20-45%) expansion occurred for the two NBR hose grades and (ECO). HNBR, neoprene, and silicone exhibited high swelling and softening, which likely precludes their use in many fuel systems. For the plastic materials, the observed swell was low; Nylon 11 swelled around 15%, but otherwise, their measured swell was <10%. Many of the plastics also showed sensitivity to alcohol type, as the E10 test fuel often imparted appreciably higher swell than iBu16. In general, the plastic materials showed good compatibility with the iBu16 and E10 test fuels. Here, the sole exception was the PVC material, which was structurally degraded from exposure to either fuel type. Compositional analysis showed high fuel retention in Nylon 12 and PVC. PVC also experienced a significant reduction in plasticizer compounds following exposure, which resulted in embrittlement and an increase in the glass-to-rubber transition temperature.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1972

Prebiotic phosphorylation of thymidine at 65 C in simulated desert conditions.

The phosphorylation of thymidine is described for a variety of conditions at 65 C to demonstrate that the reaction could readily take place in deserts at the present time. This might be used as an indication that urea-phosphate mixtures could have been important as phosphorylating agents on the primitive earth. Reaction products were identified by comparing their chromatographic and electrophoretic mobilities with those of authentic materials and by enzymatic degradation. The results show that good yields of nucleotides are obtained when nucleosides are heated with urea-phospate mixtures at 65 C. Reactions proceed more rapidly at moderate humidities than in a stream of dry nitrogen. Occasional wetting results in even faster and more extensive reactions. There was no reaction for a mixture of urea and trimetaphosphate.

Bishop, M. J.↗
NASA NTRS1972

NERVA turbopump bearing retainer fabrication on nonmetallic retainer

The need for a low-wear, lightweight, high strength bearing retainer material with a radiation degradation threshold of 10 to the 9th power rads (C) prompted development of nonmetallic reinforced polymers of the following types: (1) polybenzimidazole, (2) polyimide, and (3) polyquinoxaline. Retainers were machined from tubular laminates (billets), including reinforcement by either glass or graphite fabric or filament. Fabrication of billets involves hot preimpregnation of the reinforcement fabric or filament with polymer followed by wrapping this prepreg over a heated mandrel to form a tube with the required thickness and length.

Accinelli, J. B.↗
NASA NTRS1980

Silicon web process development

A barrier crucible design which consistently maintains melt stability over long periods of time was successfully tested and used in long growth runs. The pellet feeder for melt replenishment was operated continuously for growth runs of up to 17 hours. The liquid level sensor comprising a laser/sensor system was operated, performed well, and meets the requirements for maintaining liquid level height during growth and melt replenishment. An automated feedback loop connecting the feed mechanism and the liquid level sensing system was designed and constructed and operated successfully for 3.5 hours demonstrating the feasibility of semi-automated dendritic web growth. The sensitivity of the cost of sheet, to variations in capital equipment cost and recycling dendrites was calculated and it was shown that these factors have relatively little impact on sheet cost. Dendrites from web which had gone all the way through the solar cell fabrication process, when melted and grown into web, produce crystals which show no degradation in cell efficiency. Material quality remains high and cells made from web grown at the start, during, and the end of a run from a replenished melt show comparable efficiencies.

Duncan, C. S.↗
NASA NTRS1982

Environmental isolation task

The failure-analysis process was organized into a more specific set of long-term degradation steps so that material property change can be differentiated from module damage and module failure. Increasing module performance and life are discussed. A polymeric aging computer model is discussed. Early detection of polymer surface reactions due to aging is reported.

Coulbert, C. D.↗
NASA NTRS1983

Test program to demonstrate the stability of hydrazine in propellant tanks

A 24-month coupon test program to evaluate the decomposition of propellant tanks is reported. The propellant fuel evaluated was monopropellant-grade hydrazine (N2H4), which is normally a colorless, fuming, corrosive, strongly reducing liquid. The degree of hydrazine decomposition was determined by means of chemical analyses of the liquid and evolved gases at the end of the test program. The experimental rates of hydrazine decomposition were determined to be within acceptable limits. The propellant tank materials and material combinations were not degraded by a 2-year exposure to hydrazine propellant. This was verified using change-of-weight determinations and microscopic examination of the specimen surface before and after exposure, and by posttest chemical analyses of hydrazine liquid for residual metal content.

Moran, C. M.↗
NASA NTRS1984

Determination of the stiffness reduction of (0,90, + or - N 45) graphite/epoxy laminates under cyclic loading

A series of tests has been performed to determine the effect of fatigue loading on the stiffness degradation of graphite/epoxy composite materials. Specimens were tested in tension-tension fatigue at a loading frequency of 10 Hz and a stress ratio of 0.1, for a wide range of stress levels. During this investigation, both static and dynamic stiffnesses were continually monitored for the range of stress levels tested, and the results are presented in tabular and graphical form.

Jones, D. L.↗
NASA NTRS1986

Production of pulsed atomic oxygen beams via laser vaporization methods

The generation of energetic pulsed atomic oxygen beams by laser-driven evaporation of cryogenically frozen ozone/oxygen films and thin indium-tin oxide (ITO) films is reported. Mass spectroscopy is used in the mass and energy characterization of beams from the ozone/oxygen films, and a peak flux of 3 x 10 to the 20th/sq m per sec at 10 eV is found. Analysis of the time-of-flight data suggests that several processes contribute to the formation of the oxygen beam. Results show the absence of metastable states such as the 2p(3)3s(1)(5S) level of atomic oxygen blown-off from the ITO films. The present process has application to the study of the oxygen degradation problem of LEO materials.

Brinza, David E.↗
NASA NTRS1989

Advances in thin-film solar cells for lightweight space photovoltaic power

The development of photovoltaic arrays beyond the next generation is discussed with attention given to the potentials of thin-film polycrystalline and amorphous cells. Of particular importance is the efficiency (the fraction of incident solar energy converted to electricity) and specific power (power to weight ratio). It is found that the radiation tolerance of thin-film materials is far greater than that of single crystal materials. CuInSe2 shows no degradation when exposed to 1-MeV electrons.

Landis, Geoffrey A.↗
NASA NTRS1991

Magellan - Initial analysis of Venus surface modification

Images of the Venus surface provided by the Magellan mission make it possible to see the fine-scale features diagnostic of weathering, erosion, and deposition. These include ejecta deposits extending up to 1000 km to the west of several impact craters, windblown deposits, features containing both obstacles and a source of particulate material, and evidence for degradation by atmosphere-surface interactions and mass movements. Initial Magellan observations pertaining to the nature, rate, and history of surficial processes are analyzed. Emphasis is placed on radar imaging, but results from radiometry and altimetry observations are also discussed.

Arvidson, R. E.↗
NASA NTRS1992

Evaluation of selected thermal control coatings for long-life space structures

Graphite-reinforced resin matrix composites are being considered for spacecraft structural applications because of their light weight, high stiffness, and lower thermal expansion. Thin protective coatings with stable optical properties and the proper ratio of solar absorption (alpha sub s) to thermal emittance (epsilon) minimize orbital thermal extremes and protect these materials against space environment degradation. Sputtered coatings applied directly to graphite/epoxy composite surfaces and anodized coatings applied to thin aluminum foil were studied for use both as an atomic oxygen barrier and as thermal control coatings. Additional effort was made to develop nickel-based coatings which could be applied directly to composites. These coating systems were selected because their inherent tenacity made them potentially more reliable than commercial white paints for long-life space missions. Results indicate that anodized aluminum foil coatings are suitable for tubular and flat composite structures on large platforms in low Earth orbit. Anodized foil provides protection against some elements of the natural space environment (atomic oxygen, ultraviolet, and particulate radiation) and offers a broad range of tailored alpha sub s/epsilon. The foil is readily available and can be produced in large quantities, while the anodizing process is a routine commercial technique.

Teichman, Louis A.↗
NASA NTRS1992

The LDEF experience. Materials

An overview is provided of the LDEF (Long Duration Exposure Facility) mission and the preliminary findings, focusing on the materials related disciplines. These findings are based on observations of low-earth orbit environmental effects on materials made in space during LDEF retrieval and during LDEF tray deintegration, and on initial findings of laboratory analyses of LDEF materials. Included are effects of individual environmental parameters: atomic oxygen, ultraviolet radiation, meteoroid and debris impacts, thermal cycling, vacuum, and contamination, plus combined effects of these parameters. Materials considered include thermal control coatings and surface treatments, ceramics and glasses, metals, polymers, and polymer matrix composites. In general, preliminary LDEF data are remarkably consistent; LDEF will provide a benchmark for materials design data bases for satellites in low earth orbit. Some materials were identified to be encouragingly resistant to low earth orbit space environmental effects for 5.8 years; other space qualified materials displayed significant environmental degradation. Molecular contamination was widespread.

Stein, Bland A.↗
NASA NTRS1993

Long-duration orbital effects on optical coating materials

We flew specimens of eight different optical coating materials in low earth orbit as part of the Long Duration Exposure Facility manifest to determine their ability to withstand exposure to the residual atomic 0 and other environmental effects at those altitudes. We included samples of Al, Au, Ir, Os, Pt, Al + MgF2, Al + SiO(x), and chemical-vapor-deposited SiC, representing reflective optical applications from the vacuum ultraviolet through the visible portions of the spectrum. We found that the majority of the materials suffered sufficient reflectance degradation to warrant careful consideration in the design of future space-flight instrumentation.

Herzig, Howard↗
NASA NTRS1993

Superconducting Al-trilayer tunnel junctions for use as X-ray detectors

Photolithographic techniques have been developed to fabricate high-quality Al-Al oxide-Al superconducting tunnel junctions for use in X-ray detectors. These devices are designed to incorporate about 1-micron-thick superconducting X-ray absorbers for the detection of less than 10-keV single photons. In an effort to increase energy resolution, superconductor bandgap engineering with lateral and vertical trapping has been used to shorten quasi-particle tunneling times and diffusion lengths and to prevent quasi-particle diffusion away from the tunnel junction. Methods that have been developed for overcoming materials imcompatibility and device degradation upon thermal cycling are reported. The authors also report on the use of a nonrectangular tunnel junction geometry which reduces the magnetic field needed to suppress the Josephson current for stable biasing. Work in progress to measure the energy resolution of these X-ray detectors at 0.35 K is also discussed.

Gaidis, M. C.↗
NASA NTRS1992

Multiple dataset water-quality analyses in the vicinity of an ocean wastewater plume

The White's Point ocean outfall is the method of disposal for approximately 374 million gallons of treated wastewater per day from Los Angeles County. The photosynthetic characteristics and particle distributions have well-defined properties that can be exploited to yield information on transport of the plume, mixing dynamics, and resuspension of bottom sediments during periods of bottom current velocity in excess of ca. 0.1 m/s. This plume of particles serves as a conservative tracer, which was studied using a number of sampling platforms and strategies, including underway sawtooth, or 'tow-yo' sampling, moored arrays of instruments, stationary profiling, and now for the first time with remotely-sensed multispectral color imagery. Research in this area previously focused on examination of the plume as it relates to the local current field and transport of particles, and on the resuspension of bottom sediments during periods of increased currents. In addition, Wu et al elucidated techniques for separating the particle signal into photosynthetic and nonphotosynthetic components, based on the beam attenuation to chlorophyll fluorescence ratio. High-frequency time series measurements of the current field and bio-optical characteristics at a site close to the waste diffusers were also collected. These are being analyzed for the spectral characteristics of the longer-timescale variability, in order to predict particle transport through simple meteorological measurements. With the advent of high spectral and spatial resolution imaging spectrometers such as AVIRIS, it is now possible to construct causal relationships between particle distributions and signature of the upwelled radiance from the surface. The availability of a constant and well-characterized source of material lends itself well to models which predict upwelled radiance from the surface. The availability of a constant and well-characterized source of material lends itself well to models which predict upwelled light as a function of particle distributions, photosynthetic pigments, colored dissolved organic material, and detrital and degradation products of photosynthesis. In addition, the spatial coverage provided by the tow-yo sampling device, combined with the profile measurements of the light field, should facilitate the best inverse modeling attempts possible thus far.

Hamilton, Michael↗
NASA NTRS2000

The Hubble Space Telescope Servicing Mission 3A Contamination Control Program

After nearly 10 years on-orbit, the Hubble Space Telescope (HST) external thermal control materials and paint have degraded due to exposure to the low Earth orbit environment. This presented a potentially large on-orbit contamination source (particles and/or debris). Contamination mitigation techniques were developed to augment existing on-orbit servicing contamination controls. They encompassed mission management, crew training, and crew aids and tools. These techniques were successfully employed during the HST Servicing Mission 3A, December 1999.

Hansen, Patricia A.↗
NASA NTRS1996

Comparison of aerobically-treated and untreated crop residue as a source of recycled nutrients in a recirculating hydroponic system

This study compared the growth of potato plants on nutrients recycled from inedible potato biomass. Plants were grown for 105 days in recirculating, thin-film hydroponic systems containing four separate nutrient solution treatments: (1) modified half-strength Hoagland's (control), 2) liquid effluent from a bioreactor containing inedible potato biomass, 3) filtered (0.2 micrometer) effluent, and 4) the water soluble fraction of inedible potato biomass (leachate). Approximately 50% of the total nutrient requirement in treatments 2-4 were provided (recycled) from the potato biomass. Leachate had an inhibitory effect on leaf conductance, photosynthetic rate, and growth (50% reduction in plant height and 60% reduction in tuber yield). Plants grown on bioreactor effluent (filtered or unfiltered) were similar to the control plants. These results indicated that rapidly degraded, water soluble organic material contained in the inedible biomass, i.e., material in leachate, brought about phytotoxicity in the hydroponic culture of potato. Recalcitrant, water soluble organic material accumulated in all nutrient recycling treatments (650% increase after 105 days), but no increase in rhizosphere microbial numbers was observed.

NASA Discipline Life Support Systems↗