Results for “High pressure instruments” — Page 52

NASA NTRS1995

Hypersonic aerodynamics test facility using the external propulsion accelerator

The use of the External propulsion Accelerator (EPA) for launching models of hypersonic aerodynamic configurations into an instrumented ballistic range is discussed. The aerodynamic model is encased inside an axisymmetric projectile designed to be accelerated to high speed in the EPA. Accelerator lengths required to achieve hypersonic speeds are estimated to vary from 10 meters for Mach 7, 40 meters for Mach 10, 150 meters for Mach 15, and 700 meters for Mach 30, assuming a limit of 50,000 g's acceleration. For a model span of 10 cm to 25 cm, the launch tube diameters are 40 cm and 100 cm, respectively. Using this EPA launcher will enable exact simulation of hypersonic flight in ground facilities where both the gas composition and pressure can be controlled in the ballistic range.

Rom, J.↗

NASA NTRSDate not supplied

Bluntness and Supersaturation Effects on the Second Mode Instability in Mach 10 Flow

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 31-Inch Mach 10 Tunnel to investigate the impact of nosetip radius and freestream supersaturation on the development of the second mode instability. The model was instrumented with surface-mounted Kulite® and PCB® pressure transducers and thermocouples. Power spectral density plots demonstrate the anticipated trends of the second mode instability weakening and shifting to lower frequencies with increased bluntness. Heat transfer measurements suggest laminar flow over the bulk of the model for most testing conditions, with evidence of transition by the cone base for the sharpest nosetip (R = 0.15 mm) at the higher unit Reynolds numbers. The dynamic surface pressure and heat transfer measurements show that reducing the temperature of the freestream to a supersaturated state has a significant stabilizing effect on the model boundary layer. The surface measurements are observed to be highly dependent on the level of clustering in the freestream. Significant changes in surface pressure spectra due to total temperature reduction are first noted below T0= 948 K, while more substantial fluctuation reductions are found below T0= 810 K.

Hypersonics↗

NASA NTRSDate not supplied

Computational and Physics-Based Modeling for the Development of in-Space Welding Technology

Welding will be an enabling technology for in-space assembly and manufacturing (ISAM) and in-space repair operations in support of the growing Space Economy. Prospective use cases of welding include metal repair on long-duration lunar surface missions and assembly of large structures that exceed dimensions of the currently available launch vehicle envelopes such as space arrays, tall lunar transmission towers, or even large transit vehicles powered by nuclear propulsion. There is a brief history of beam welding for in-space use. Soviet and NASA astronauts performed electron beam welds (EBW) in space in the late-1960s through mid-1980s and several parabolic flights of laser beam welding (LBW) were undertaken in the USA and Canada in the early-1990s. Work has since stagnated until the recent boom of the in-space economy has demonstrated need for continued development of EBW and LBW processes, which are desirable for their compactness, low mass, low power consumption, and high wall plug efficiency. No space-based manufacturing laboratory capable of demonstrating, developing, and applying welding processes exists, and costs are high to develop and fly individual space-based trials. This drives the current approach to develop welding technology with computational and physics-based models in tandem with earth-based experiments. Several approaches are taken to complement and drive the selection of instrumentation for planned parabolic and suborbital flights. First, a thermal model of Skylab EBW experiments is established and compared to empirical data. Next, the model is used to show variation between Earth-based and in-space weld structure and properties through exploration of key variables that define the Low earth orbit and lunar surface space environments, namely temperature (40 – 400 K), pressure (10-10 to 104 Pa), and gravity (10-6 g to 1 g). Finally, physical processes associated with heat and mass transport during welding are evaluated through several case studies across the above variable ranges demonstrating need for further research.

in-space welding↗

DOE OSTI2022

Validation of Printed Strain Gauges at Moderate Temperatures (up to 300°C)

Strain gauges in material test reactors serve to generate critical mechanical property data for qualifying the performance of reactor components. Resistance based strain gauge technologies are both well established and commercially available; however, they present limitations in terms of reactor experiment conditions, especially in areas where physical space is a challenge. In this work, an additively manufactured capacitance-based strain gauge was printed on a stainless-steel specimen and tested at up to the prototypic pressurized-water reactor operating temperature of 300°C. In addition, a high-temperature resistive strain gauge (RSG) was used to better understand how the RSGs operate, and to provide baseline measurements for comparison against the printed strain gauges. Future development of printed strain gauges will focus on expanding their temperature limits to 500°C and enabling applications currently beyond the capabilities of commercial RSGs.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Measuring aerosol collection efficiency for the Bladewerx “New Speclon TM 5” and the older “Speclon TM 5” filter

Bladewerx TM LLC (Rio Rancho, NM) manufactures instrumentation, neutron shielding and activation foils for the radiation protection industry. Specializing in portable alpha/beta air monitors and sample counters, Bladewerx is the source of Speclon TM PTFE filter media that they recommend for high-resolution alpha spectroscopy. Los Alamos National Laboratory (LANL) utilizes Speclon TM filter material in CAM (Continuous Air Monitor) samplers for workplace air monitoring. The LANL Aerosol Engineering Facility received air filter material from Bladewerx, referred to as “New Speclon 5” in this document, in order to distinguish from filter material that was previously received (referred to as “Speclon 5” in this document). In this document, the aerosol collection efficiency and airflow resistance (pressure drop) were measured for the New Speclon 5 filter material.

61 RADIATION PROTECTION AND DOSIMETRY↗

NASA NTRS1980

Design of a high precision microwave reflector

Development of a high accuracy spherical microwave reflector to support contour RMS and pointing requirements for a new series of space instruments is reported. The reflector system is composed of precision machined aluminum tile reflectors supported from a eutectic coated graphite epoxy structure by flexures. Several basic technologies have been integrated into a manufacturing process that accommodates fabrication techniques of both optical and composite constraints. The optical figure and its change due to thermal gradient was measured in a thermal vacuum environment with a Ronchi system. The radiometer system is in support of the Microwave Limb Sounder, an experiment to measure emissions from earth's atmospheric limb thus obtaining wind, temperature, pressure and chemical composition measurements.

Noller, E. W.↗

NASA NTRS2014

Comparison of Martian Surface Radiation Predictions to the Measurements of Mars Science Laboratory Radiation Assessment Detector (MSL/RAD)

For the analysis of radiation risks to astronauts and planning exploratory space missions, detailed knowledge of particle spectra is an important factor. Detailed measurements of the energetic particle radiation environment on the surface of Mars have been made by the Mars Science Laboratory Radiation Assessment Detector (MSL-RAD) on the Curiosity rover since August 2012, and particle fluxes for a wide range of ion species (up to several hundred MeV/u) and high energy neutrons (8 - 1000 MeV) have been available for the first 200 sols. Although the data obtained on the surface of Mars for 200 sols are limited in the narrow energy spectra, the simulation results using the Badhwar-O'Neill galactic cosmic ray (GCR) environment model and the high-charge and energy transport (HZETRN) code are compared to the data. For the nuclear interactions of primary GCR through Mars atmosphere and Curiosity rover, the quantum multiple scattering theory of nuclear fragmentation (QMSFRG) is used, which includes direct knockout, evaporation and nuclear coalescence. Daily atmospheric pressure measurements at Gale Crater by the MSL Rover Environmental Monitoring Station are implemented into transport calculations for describing the daily column depth of atmosphere. Particles impinging on top of the Martian atmosphere reach the RAD after traversing varying depths of atmosphere that depend on the slant angles, and the model accounts for shielding of the RAD by the rest of the instrument. Calculations of stopping particle spectra are in good agreement with the RAD measurements for the first 200 sols by accounting changing heliospheric conditions and atmospheric pressure. Detailed comparisons between model predictions and spectral data of various particle types provide the validation of radiation transport models, and thus increase the accuracy of the predictions of future radiation environments on Mars. These contributions lend support to the understanding of radiation health risks to astronauts for the planning of various mission scenarios.

Kim, Myung-Hee Y.↗

NASA NTRSDate not supplied

Predicting SLS Launch Environment using a Novel Multiphase Formulation

Powerful acoustic waves generated during ignition of launch vehicles may be dangerous to the vehicle, its payload, or the surrounding structures. The water-based Ignition Overpressure and Sound Suppression (IOP/SS) system at Kennedy Space Center’s (KSC) Launch Complex 39B (LC-39B) will be used to protect the Space Launch System (SLS) from the acoustic vibrations generated during launch. The IOP/SS system uses enormous amounts of water to dampen and attenuate these sound waves. To better understand the launch environment risks and to study the effectiveness of the IOP/SS system it is desirable to have time-accurate unsteady simulations of the vehicle ignition with water-based sound suppression. This paper presents results obtained with a novel, high-order accurate, and robust numerical method designed for simulating compressible multiphase flows. A positivity-preserving finite difference scheme is utilized which is formally high-order accurate and also provably robust. Robustness is critical due to the extreme nature of the flow which exhibits highly nonlinear shock and rarefaction waves interacting with liquid-gas interfaces with density ratios of the order of 1000:1. Furthermore, the high-order accuracy (and the high resolution property) is desirable for predicting wave phenomena like IOP waves since the signal can be resolved accurately and propagated long distances with fewer grid points. This finite-difference method was developed using NASA’s Launch, Ascent, and Vehicle Aerodynamics (LAVA) Cartesian immersed boundary framework. We present a validation case by applying our solver to the SLS Scale Model Acoustic Test (SMAT). The SLS SMAT is a well-instrumented 5% scale model test meant to represent the SLS at NASA KSC’s LC-39B pad. Scale IOP tests were performed with and without the sound suppression water and included many sensors which recorded the pressure waves produced during ignition. For this validation case we conduct two simulations, likewise with and without sound suppression water, and compare the SLS SMAT pressure sensor signals with our numerical signals at identical locations. Following this validation case we present a study of the SLS launch environment to examine engineering safety concerns about the mobile launch pad. Engineers at KSC redesigned the main flame deflector at LC-39B anticipating the increased loads from the SLS and to repair damage from prior Shuttle missions. This deflector redesign made use of surface pressure and temperature data from LAVA full-scale SLS simulations without the sound suppression system. The engineers were questioning the possibility of increased pressure loads on the underside of the mobile launcher due to the water in the flame trench. Based on the results established in our simulations of the SLS SMAT, we performed updated calculations for SLS at LC-39B with and without water systems active to assess the readiness of the launch pad for Artemis I launch. Our results show that the IOP/SS system is effective at reducing the overpressure signal and overall sound pressure levels felt by the vehicle and additionally that the pressure loads experienced by the mobile launcher (ML) during engine startup is not increased by the presence of water.

EGS↗

NASA NTRSDate not supplied

A Dynamic PCA and Machine Learning Tool for Automated Identification of Solar Wind Disturbances Impacting Earth’s Magnetosphere

Earth’s magnetosphere is continuously impacted by solar wind and interplanetary magnetic field (IMF) disturbances, such as shocks, discontinuities, magnetic clouds and more. Understanding how such disturbances propagate from the Sun and what is their impact on the different magnetospheric domains is key to understanding and forecasting energy transfer from the solar wind to Earth. The large number of overlapping solar wind and magnetospheric missions carrying magnetometers and the recent advances in communications and data storage technologies have enabled an unprecedented quantity of high-fidelity magnetic field data captured by in-situ spacecraft to be available at the click of a button. However, this massive quantity of available data can prove unwieldy for researchers, limiting the identification of interesting phenomena and disturbances to a relatively small percentage of the total dataset. Several techniques have been previously developed for automated identification of specific types of magnetic anomalies, but these methods are typically mission-specific and can be difficult to generalize. We present initial results for a generic method of automated anomaly detection in magnetic field measurements based on dimensionality reduction and unsupervised clustering via machine learning. The benefit of our technique is its high degree of generalizability and flexibility which make it a most useful data survey tool for a wide range of magnetic field datasets. This method can also be applied simultaneously to other observed time-series properties like plasma density, pressure, and velocity for more accurate event identification. Additionally, the application of this method to data captured by multiple spacecraft enables the simultaneous identification of disturbances and the determination of their propagation characteristics. Initial evaluation of this technique has been performed using data from Magnetospheric MultiScale (MMS) and THEMIS-ARTEMIS missions, providing a testbed scenario for the future Heliophysics Environmental and Radiation Measurement Experiment Suite (HERMES) platform instruments that will measure solar wind and IMF properties from lunar orbit onboard the Gateway station.

Miguel Martinez-Ledesma↗

NASA NTRSDate not supplied

A Dynamic PCA and Machine Learning Tool for Automated Identification of Solar Wind Disturbances Impacting Earth’s Magnetosphere

Earth’s magnetosphere is continuously impacted by solar wind and interplanetary magnetic field (IMF) disturbances, such as shocks, discontinuities, magnetic clouds and more. Understanding how such disturbances propagate from the Sun and what is their impact on the different magnetospheric domains is key to understanding and forecasting energy transfer from the solar wind to Earth. The large number of overlapping solar wind and magnetospheric missions carrying magnetometers and the recent advances in communications and data storage technologies have enabled an unprecedented quantity of high-fidelity magnetic field data captured by in-situ spacecraft to be available at the click of a button. However, this massive quantity of available data can prove unwieldy for researchers, limiting the identification of interesting phenomena and disturbances to a relatively small percentage of the total dataset. Several techniques have been previously developed for automated identification of specific types of magnetic anomalies, but these methods are typically mission-specific and can be difficult to generalize. We present initial results for a generic method of automated anomaly detection in magnetic field measurements based on dimensionality reduction and unsupervised clustering via machine learning. The benefit of our technique is its high degree of generalizability and flexibility which make it a most useful data survey tool for a wide range of magnetic field datasets. This method can also be applied simultaneously to other observed time-series properties like plasma density, pressure, and velocity for more accurate event identification. Additionally, the application of this method to data captured by multiple spacecraft enables the simultaneous identification of disturbances and the determination of their propagation characteristics. Initial evaluation of this technique has been performed using data from Magnetospheric MultiScale (MMS) and THEMIS-ARTEMIS missions, providing a testbed scenario for the future Heliophysics Environmental and Radiation Measurement Experiment Suite (HERMES) platform instruments that will measure solar wind and IMF properties from lunar orbit onboard the Gateway station.

Miguel Martinez-Ledesma↗

DOE OSTI2020

Comparing Cetane Number Measurement Methods

Cetane number is one of the most important fuel performance metrics for mixing controlled compression-ignition “diesel” engines, quantifying a fuel’s propensity for autoignition when injected into end-of-compression-type temperature and pressure conditions. The historical default and referee method on a Cooperative Fuel Research (CFR) engine configured with indirect fuel injection and variable compression ratio is cetane number (CN) rating. A subject fuel is evaluated against primary reference fuel blends, with heptamethylnonane defining a low-reactivity endpoint of CN = 15 and hexadecane defining a high-reactivity endpoint of CN = 100. While the CN scale covers the range from zero (0) to 100, typical testing is in the range of 30 to 65 CN. Alternatively, several constant-volume combustion chamber (CVCC)-based cetane rating devices have been developed to rate fuels with an equivalent derived cetane number (DCN) or indicated cetane number (ICN). These devices measure ignition delay for fuel injected into a fixed volume of high-temperature and high-pressure air to simulate end-of-compression-type conditions. In this study, a range of novel fuel compounds are evaluated across three CVCC methods: the Ignition Quality Tester (IQT), Fuel Ignition Tester (FIT), and Advanced Fuel Ignition Delay Analyzer (AFIDA). Resulting DCNs and ICNs are compared for fuels within the normal diesel fuel range of reactivity, as well as very high (~100) and very low DCNs/ICNs (~5). Distinct differences between results from various devices are discussed. This is important to consider because some new, high-efficiency advanced compression-ignition (CI) engine combustion strategies operate with more kinetically controlled distributed combustion as opposed to mixing controlled diffusion flames. These advanced combustion strategies may benefit from new fuel chemistries, but current rating methods of CN, DCN, and ICN may not fully describe their performance. In addition, recent evidence suggests ignition delay in modern on-road diesel engines with high-pressure common rail fuel injection systems may no longer directly correlate to traditional CN fuel ratings. Simulated end-of-compression conditions are compared for CN, DCN, and ICN and discussed in the context of modern diesel engines to provide additional insight. Results highlight the potential need for revised and/or multiple fuel test conditions to measure fuel performance for advanced CI strategies.

47 OTHER INSTRUMENTATION↗

NASA NTRS2011

Low-Outgassing Photogrammetry Targets for Use in Outer Space

A short document discusses an investigation of materials for photogrammetry targets for highly sensitive optical scientific instruments to be operated in outer space and in an outer-space-environment- simulating thermal vacuum chamber on Earth. A key consideration in the selection of photogrammetry-target materials for vacuum environments is the need to prevent contamination that could degrade the optical responses of the instruments. Therefore, in addition to the high levels and uniformity of reflectivity required of photogrammetry-target materials suitable for use in air, the materials sought must exhibit minimal outgassing. Commercially available photogrammetry targets were found to outgas excessively under the thermal and vacuum conditions of interest; this finding prompted the investigators to consider optically equivalent or superior, lower-outgassing alternative target materials. The document lists several materials found to satisfy the requirements, but does not state explicitly whether the materials can be used individually or must be combined in the proper sequence into layered target structures. The materials in question are an aluminized polyimide tape, an acrylic pressure- sensitive adhesive, a 500-A-thick layer of vapor-deposited aluminum, and spherical barium titanate glass beads having various diameters from 20 to 63 microns..

Gross, Jason N.↗

NASA NTRS1996

Grant Proposal for the Continuation of the Voyager Interstellar Mission: LECP Investigation

This proposal documents the plans of the Low Energy Charged Particle (LECP) investigation team for participation in NASA's Voyager Interstellar Mission (VIM) as the Voyager 1 and 2 spacecraft explore the outer reaches of the heliosphere and search for the termination shock and the heliopause. The proposal covers the four year period from 1 January 1997 to 31 December 2000. The LECP instruments on Voyager 1 and 2 measure in situ intensities of charged particles with energies from about 30 keV to 100 MeV for ions, and about 20 keV to greater than 10 MeV for electrons. The instruments provide detailed spectral, angular, and compositional information about the particles. Composition is available for greater than 200 keV/nuc using multi-parameter measurements. Angular information is obtained by a mechanically scanned platform that rotates at various commanded rates. Measurements of low energy ion and electron intensities versus time and spatial location within the heliosphere contain an abundance of information regarding various transport and acceleration processes on both local (approx. 1 hr, approx. 0.01 AU) and global (approx. 11 yrs, approx. 100 AU) scales. The LECP instruments provide unique observations of such dynamical processes, and we anticipate that it will return critical information regarding the boundaries of the heliosphere. Several recent and exciting discoveries based on LECP measurements emphasize the important role that low energy charged particle distributions play in physical processes in the interplanetary medium. Yet, at the same time, these discoveries also underscore the fact that our understanding of processes in the outer heliosphere is, in most cases, incomplete, and in others, only rudimentary at best. Among the discoveries referred to above are the following: (1) Shocks: Examination of greater than 30 keV ion intensities have revealed: (a) a total absence of acceleration beyond only -100-200 keV at a strong transient shock in May 1991 at 35 AU, despite an enhanced level of seed particles; (b) a large transient shock in September 1991 of global scale, with intensities of shock-accelerated ions greater than or equal to 30 keV to approx. 30 MeV showing complex, highly energy-dependent spatial evolution, and small-scale (approx. few gyroradii), often anisotropic, micro-structures; (c) recurrent intensity increases in greater than or equal to 30 keV to -few MeV ions, with structures that, in some cases, show no correlation with the associated corotating shock. (2) Superthermal ion pressure: A global merged interaction region with a leading shock, downstream of which the superthermal ion (greater than or equal to 30 keV to approx. 4 MeV) pressure is comparable to that of the thermal plasma, and the total particle pressure yields a plasma beta of order unity. (3) Pickup ions: Measurements of the C/O ratio within transient structures at 35-45 AU showing the first clear evidence that transient shocks can pre-accelerate interstellar pickup ions from approx. 1 keV/nuc to at least 1 MeV/nuc. (4) Seed particles: Injection of ions for acceleration to high energies at the termination shock is unlikely to be a problem, since interplanetary transient and recurrent shocks are continually accelerating ions, of solar wind or interstellar origin, to highly superthermal energies. (5) Precursor electrons: Ambient solar electrons (greater than or equal to few tens of keV) that exist in the outer heliosphere ca form a broad precursor, several days wide, that is upstream of the termination shock and potentially observable a few months prior to the shock crossing. (6) Solar wind velocity at Voyager 1: We can use LECP ion data to obtain the solar wind velocity at Voyager 1, enabling us to provide critical measurement of the plasma flow as we approach and encounter the termination shock and other regions (necessary due to the partial failure of the Voyager 1 PLS experiment). The work of the LECP investigator team during the VIM will include: (1) Continuing operations with regard to the receipt, processing, verification, cataloging, display, and distribution of the data from the LECP instruments on Voyager 1 and 2, (2) Monitoring the health and performance of the LECP instruments, and evaluating and characterizing the response of the LECP instruments to various energetic particle and plasma environments, (3) Participating in, and supporting Voyager Project planning exercises and other coordinated activities relevant to exploration of the outer heliosphere, (4) Developing analysis techniques and operational procedures suitable for searching for and characterizing the boundaries and unique regions of the outher heliosphere, (5) Continuing the preparation of data sets appropriate for submission to the National Space Sciences Data Center (NSSDC) and, where appropriate, the Planetary Data System (PDS), (6) Maintaining direct Web access to online LECP data through the JHU/APL Voyager LECP home page, (7) Performing scientific evaluations of the Voyager 1 and 2 LECP data sets in conjunction with other data sets and other investigators, with particular focus on the outer regions of the heliosphere, and (8) Publishing the results of these evaluations in the scientific literature and presenting the results in scientific conferences.

Krimigis, Stamatios M.↗

NASA NTRS1986

The HD/H2 ratio in the atmosphere of Uranus

High resolution spectra of HD and H2 were brought together to derive the D/H ratio for Uranus. The deuterium concentration in the dominant molecular hydrogen phase is least susceptible to the effects of isotope fractionation in the planetary atmosphere, and the determination of relative abundances of HD and H2 is unambiguous due to nearness and relative weakness of the chosen spectral lines. The HD 5-0 R(0) and R(1) dipole lines and the H2 4-0 S(0), S(1), and S(2) quadrupole lines were obtained with a PEPSIOS instrument at the Palomar 5-meter telescope. The H2 spectra, which resolve the asymmetric line profiles resulting from pressure shifts in the deep stratified Uranus atmosphere, unambiguously define the line-of-sight hydrogen abundance for comparison with the HD spectra. The 5-0 band of HD was chosen to minimize interference from blended CH4 lines. However, weak interfering lines were found in the 5-0 bands from Uranus as well, and some uncertainties remain regarding the intrinsic line strengths in molecular hydrogen, complicating the analysis of the HD/H2 data. Nevertheless, it is established that the D/H ratio in the atmosphere of Uranus is smaller than the Jovian value, and is significantly smaller than recent theoretical predictions for Uranus based on estimates of isotope fractionation in the pre-planetary solar nebulae.

Trauger, J. T.↗

NASA NTRS2000

Analysis of the NASA White Sands Test Facility (WSTF) Test System for Friction-Ignition of Metallic Materials

Friction is a known ignition source for metals in oxygen-enriched atmospheres. The test system developed by the NASA White Sands Test Facility in response to ASTM G-94 has been used successfully to determine the relative ignition from friction of numerous metallic materials and metallic materials pairs. These results have been ranked in terms of a pressure-velocity product (PV) as measured under the prescribed test conditions. A high value of 4.1(exp 8) watts per square meter for Inconel MA 754 is used to imply resistance to friction ignition, whereas a low value of 1.04(exp 8) watts per square meter for stainless steel 304 is taken as indicating material susceptible to friction ignition. No attempt has been made to relate PV values to other material properties. This work reports the analysis of the WSTF friction-ignition test system for producing fundamental properties of metallic materials relating to ignition through friction. Three materials, aluminum, titanium, and nickel were tested in the WSTF frictional ignition instrument system under atmospheres of oxygen or nitrogen. Test conditions were modified to reach a steady state of operation, that is applied, the force was reduced and the rotational speed was reduced. Additional temperature measurements were made on the stator sample. The aluminum immediately galled on contact (reproducible) and the test was stopped. Titanium immediately ignited as a result of non-uniform contact of the stator and rotor. This was reproducible. A portion of the stator sampled burned, but the test continued. Temperature measurements on the stator were used to validate the mathematical model used for estimating the interface (stator/rotor) temperature. These interface temperature measurements and the associate thermal flux into the stator were used to distinguish material-phase transitions, chemical reaction, and mechanical work. The mechanical work was used to analyze surface asperities in the materials and to estimate a coefficient of fiction. The coefficient of fiction was analyzed in terms of material properties that is, hardness, Young's modulus and elasticity/plasticity of the material.

Shoffstall, Michael S.↗

NASA NTRSDate not supplied

Trajectory Reconstruction of the Low-Earth Orbit Flight Test of an Inflatable Decelerator

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) project conducted a flight test of a 6m inflatable aeroshell. The LOFTID test article was a secondary payload on an Atlas V launcher that carried the Joint Polar Satellite System-2 (JPSS-2) as its primary payload. The vehicle launched on November 10th, 2022. After reaching orbit, the LOFTID test article inflated the aeroshell, separated from the upper stage on an entry trajectory, and entered the atmosphere to splash down in the Pacific Ocean under parachutes. The test concept of operations is shown in Figure 1. The test article was instrumented with a variety of sensors to be used for post-flight evaluation of vehicle performance. Data from one of the key sensors for trajectory reconstruction, the Inertial Measurement Unit (IMU), was not captured in the data recorder due to a malfunction. Data from the nose cone mounted Flush Air Data Sensing (FADS) system were successfully acquired. The layout of the FADS sensors and the measured pressures during atmospheric entry are shown in Figure 2. The FADS data were combined with a Newtonian flow pressure model [1, 2] to produce estimates of the atmospheric relative trajectory. A Mach number anchoring technique given in [2] was used to stabilize estimates in high speed flight conditions. Since no IMU data were available, a trajectory simulation was used to provide the Mach number time history. The resulting estimates of the atmospheric-relative trajectory are shown in Figures 3. Given the loss of the IMU data, alternate methods for trajectory reconstruction are being explored. One approach under investigation is the use of the on-board video recorder data to be analyzed to reconstruct attitude motion. This approach is currently under investigation and will be reported on in the final paper. The Newtonian flow pressure model for the FADS analysis will also be updated with a CFD-based pressure model.

Christopher D Karlgaard↗

NASA NTRSDate not supplied

Trajectory Reconstruction of the Low-Earth Orbit Flight Test of an Inflatable Decelerator

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) project conducted a flight test of a 6m inflatable aeroshell. The LOFTID test article was a secondary payload on an Atlas V launcher that carried the Joint Polar Satellite System-2 (JPSS-2) as its primary payload. The vehicle launched on November 10th, 2022. After reaching orbit, the LOFTID test article inflated the aeroshell, separated from the upper stage on an entry trajectory, and entered the atmosphere to splash down in the Pacific Ocean under parachutes. The test concept of operations is shown in Figure 1. The test article was instrumented with a variety of sensors to be used for post-flight evaluation of vehicle performance. Data from one of the key sensors for trajectory reconstruction, the Inertial Measurement Unit (IMU), was not captured in the data recorder due to a malfunction. Data from the nose cone mounted Flush Air Data Sensing (FADS) system were successfully acquired. The layout of the FADS sensors and the measured pressures during atmospheric entry are shown in Figure 2. The FADS data were combined with a Newtonian flow pressure model [1, 2] to produce estimates of the atmospheric relative trajectory. A Mach number anchoring technique given in [2] was used to stabilize estimates in high speed flight conditions. Since no IMU data were available, a trajectory simulation was used to provide the Mach number time history. The resulting estimates of the atmospheric-relative trajectory are shown in Figures 3. Given the loss of the IMU data, alternate methods for trajectory reconstruction are being explored. One approach under investigation is the use of the on-board video recorder data to be analyzed to reconstruct attitude motion. This approach is currently under investigation and will be reported on in the final paper. The Newtonian flow pressure model for the FADS analysis will also be updated with a CFD-based pressure model.

Christopher D. Karlgaard↗

DOE OSTI2021

SPEARS: A Database-Invariant Spectral modeling API

The Spectral Physics Environment for Advanced Remote Sensing (SPEARS) application programming interface (API) is a Python-based, line-by-line, local thermal equilibrium (LTE) spectral modeling code which is optimized for simultaneously synthesizing optical spectra from any combination of fundamental spectroscopic databases. In this article, we contribute two novel spectral modeling techniques to the scientific literature. First we describe how SPEARS integrates a physics-based collisional model for calculating pressure broadening in the absence of available broadening coefficients. With this collisional model implementation, a generalized approach to fundamental spectroscopic databases can be achieved across multiple databases. We also detail our adaptive grid mesh algorithm developed to make the code scalable for simulating large spectral bandwidths at high spectral fidelity using intuitive grid parameters. Here, we present comparisons to other modeling tools, experiments, and provide a discussion on the SPEARS user interface.

47 OTHER INSTRUMENTATION↗