Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLOW MODELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Unsteady flowfield simulation of ducted prop-fan configurations

A technique for the simulation of unsteady flows in and around complex rotating machinery is presented. Additional domain decomposition mechanisms are introduced which extend the range of applicability of software developed for the time-accurate simulation of rotating machinery flowfields. The flow models uses the unsteady 3D Euler equations, discretized as a finite-volume method, utilizing a high-resolution approximate Riemann solver for cell interface flux definitions. Multiblock domain decomposition is used to partition the field radially, axially, as well as circumferentially into an ordered arrangement of blocks which exhibit varying degrees of similarity. A general high-order numerical scheme is applied to satisfy the geometric conservation law. Two configurations are presented - ducted single rotation prop-fan and a rotor-deswirl vane combination which form a single stage fan. Comparisons are made to other numerical solutions for these geometries and to available experimental data.

Janus, J. M.↗
NASA NTRS1992

Pressure oscillation in the leakage annulus between a shrouded impeller and its housing due to impeller-discharge-pressure disturbances

The perturbed flow in the leakage path between a shrouded-pump impeller and its housing is analyzed using experiences with the Space Shuttle Main Engine (SSME), high pressure fuel turbopump (HPFTP) wearing-ring seals. Analysis is based on a bulk-flow model which consists of the path-momentum, circumferential momentum, and continuity equations. The pressure oscillations in the leakage annulus are driven by a circumferential variation of the impeller discharge pressure. It is shown that the occurrence and nature of the pressure oscillations depend on the tangential-velocity ratio of the fluid entering the seal, the order of the Fourier coefficient, the closeness of the precessional frequency of the rotating pressure field to the first natural frequency of the fluid annulus, and the clearance of the wearing-ring seal. The results obtained may explain the internal melting observed on SSME HPFTP seal parts.

Childs, D. W.↗
NASA NTRS1993

A full-scale STOVL ejector experiment

The design and development of thrust augmenting short take-off and vertical landing (STOVL) ejectors has typically been an iterative process. In this investigation, static performance tests of a full-scale vertical lift ejector were performed at primary flow temperatures up to 1560 R (1100 F). Flow visualization (smoke generators, yarn tufts and paint dots) was used to assess inlet flowfield characteristics, especially around the primary nozzle and end plates. Performance calculations are presented for ambient temperatures close to 480 R (20 F) and 535 R (75 F) which simulate 'seasonal' aircraft operating conditions. Resulting thrust augmentation ratios are presented as functions of nozzle pressure ratio and temperature. Full-scale experimental tests such as this are expensive, and difficult to implement at engine exhaust temperatures. For this reason the utility of using similarity principles -- in particular, the Munk and Prim similarity principle for isentropic flow -- was explored. At different primary temperatures, exit pressure contours are compared for similarity. A nondimensional flow parameter is then shown to eliminate primary nozzle temperature dependence and verify similarity between the hot and cold flow experiments. Under the assumption that an appropriate similarity principle can be established, then properly chosen performance parameters should be similar for both hot flow and cold flow model tests.

Barankiewicz, Wendy S.↗
NASA NTRS1993

TARGET: Rapid Capture of Process Knowledge

TARGET (Task Analysis/Rule Generation Tool) represents a new breed of tool that blends graphical process flow modeling capabilities with the function of a top-down reporting facility. Since NASA personnel frequently perform tasks that are primarily procedural in nature, TARGET models mission or task procedures and generates hierarchical reports as part of the process capture and analysis effort. Historically, capturing knowledge has proven to be one of the greatest barriers to the development of intelligent systems. Current practice generally requires lengthy interactions between the expert whose knowledge is to be captured and the knowledge engineer whose responsibility is to acquire and represent the expert's knowledge in a useful form. Although much research has been devoted to the development of methodologies and computer software to aid in the capture and representation of some types of knowledge, procedural knowledge has received relatively little attention. In essence, TARGET is one of the first tools of its kind, commercial or institutional, that is designed to support this type of knowledge capture undertaking. This paper will describe the design and development of TARGET for the acquisition and representation of procedural knowledge. The strategies employed by TARGET to support use by knowledge engineers, subject matter experts, programmers and managers will be discussed. This discussion includes the method by which the tool employs its graphical user interface to generate a task hierarchy report. Next, the approach to generate production rules for incorporation in and development of a CLIPS based expert system will be elaborated. TARGET also permits experts to visually describe procedural tasks as a common medium for knowledge refinement by the expert community and knowledge engineer making knowledge consensus possible. The paper briefly touches on the verification and validation issues facing the CLIPS rule generation aspects of TARGET. A description of efforts to support TARGET's interoperability issues on PCs, Macintoshes and UNIX workstations concludes the paper.

Ortiz, C. J.↗
NASA NTRS1993

Return flux contamination of an outgassing spacecraft in low earth orbit

The recontamination of a spacecraft surface directly exposed to the ram flux is investigated. It is assumed that the surface has been contaminated by a rocket plume contact and that, subsequent to the exposure, the contaminated surface is placed in the ram flux. A BGK-simulation was compared to both a Direct Simulation Monte Carlo (DSMC) and a Full Flow Monte Carlo (FFMC) using sensitivity analysis. Results indicate that the BGK-based simulation underpredicted the return flux contamination as compared to both the DSMC and FFMC techniques. Results from the full flow model suggest that the BGK model is inadequate to represent this physical problem.

Justiz, Charles R.↗
NASA NTRS1993

Soot agglomeration in isolated, free droplet combustion

Under the conditions of an isolated, free droplet experiment, hollow, carbonaceous structures, called soot spheres, were observed to form during the atmospheric pressure, low Reynolds number combustion of 1-methylnaphthalene. These structures which are agglomerates composed of smaller spheroidal units result from both thermophoretic effects induced by the envelope flame surrounding each drop and aerodynamic effects caused by changes in the relative gas/drop velocities. A chemically reacting flow model was used to analyze the process of sootshell formation during microgravity droplet combustion. The time-dependent temperature and gas property field surrounding the droplet was determined, and the soot cloud location for microgravity combustion of n-heptane droplets was predicted. Experiments showed that the sooting propensity of n-alkane fuel droplets can be varied through diluent substitution, oxygen-index variations, and ambient pressure reductions.

Choi, M. Y.↗
NASA NTRS1993

Computational analysis of methods for reduction of induced drag

The purpose of this effort was to perform a computational flow analysis of a design concept centered around induced drag reduction and tip-vortex energy recovery. The flow model solves the unsteady three-dimensional Euler equations, discretized as a finite-volume method, utilizing a high-resolution approximate Riemann solver for cell interface flux definitions. The numerical scheme is an approximately-factored block LU implicit Newton iterative-refinement method. Multiblock domain decomposition is used to partition the field into an ordered arrangement of blocks. Three configurations are analyzed: a baseline fuselage-wing, a fuselage-wing-nacelle, and a fuselage-wing-nacelle-propfan. Aerodynamic force coefficients, propfan performance coefficients, and flowfield maps are used to qualitatively access design efficacy. Where appropriate, comparisons are made with available experimental data.

Janus, J. M.↗
NASA NTRS1992

Current status of computational methods for transonic unsteady aerodynamics and aeroelastic applications

The current status of computational methods for unsteady aerodynamics and aeroelasticity is reviewed. The key features of challenging aeroelastic applications are discussed in terms of the flowfield state: low-angle high speed flows and high-angle vortex-dominated flows. The critical role played by viscous effects in determining aeroelastic stability for conditions of incipient flow separation is stressed. The need for a variety of flow modeling tools, from linear formulations to implementations of the Navier-Stokes equations, is emphasized. Estimates of computer run times for flutter calculations using several computational methods are given. Application of these methods for unsteady aerodynamic and transonic flutter calculations for airfoils, wings, and configurations are summarized. Finally, recommendations are made concerning future research directions.

Edwards, J. W.↗
NASA NTRS1993

Double shock pairs in the solar wind

A numerical study of the evolution of a velocity enhancement disturbance in the solar wind is presented in terms of a 1D isentropic MHD flow model. It is shown that the disturbance steepens and evolves into a double shock pair while propagating outward away from the sun. The double shock pair consists of a reverse fast shock, a reverse slow shock, a forward slow shock, and a forward fast shock in order of distance away from the sun. The formation time of the double shock pair is nearly inversely proportional to the average velocity gradient of the disturbance. When the double shock pair is fully developed, the strength of the fast shocks is essentially determined by the disturbance amplitude, while the slow shocks behave differently. Their strength increases first with the disturbance amplitude but starts to decrease once the disturbance amplitude exceeds a certain value.

Hu, Y. Q.↗
NASA NTRS1992

The magnetic field in the heliosheath

The interplanetary magnetic field (IMF) behaves in a reasonably well-understood manner between the Sun and the heliospheric termination shock. At the shock, the azimuthal field is amplified by a factor of four (for a strong shock) and undergoes secular amplification in the heliosheath until the flow is fully turned into the downstream direction and has reached its asymptotic state in the distant heliotail. This amplification may lead to important MHD effects that can cause the shock to be closer to the Sun than otherwise expected. Here we further examine whether there are important MHD effects in the heliosheath. We do this by calculating the kinematic compression of the magnetic field in the heliosheath using an analytic incompressible flow model of the dynamics downstream of the shock. We conclude that it is likely that MHD effects are important in the heliosheath in a narrow cone about the upstream direction.

Suess, S. T.↗
NASA NTRS1993

Periodicity and chaos from switched flow systems - Contrasting examples of discretely controlled continuous systems

We analyze two examples of the discrete control of a continuous variable system. These examples exhibit what may be regarded as the two extremes of complexity of the closed-loop behavior: one is eventually periodic, the other is chaotic. Our examples are derived from sampled deterministic flow models. These are of interest in their own right but have also been used as models for certain aspects of manufacturing systems. In each case, we give a precise characterization of the closed-loop behavior.

Chase, Christopher↗
NASA NTRS1992

Constraints on electron acceleration in the Crab nebula

Using the radio through hard X-ray images of the Crab nebula to derive the spatial dependence of the electron spectrum and the magnetic field distribution from MHD flow models, we have rederived the high-energy spectrum of inverse Compton scattered gamma rays. We find agreement with the observed spectrum at TeV energies, but it is clear that the inverse Compton flux does not contribute significantly to the unpulsed nebular emission observed by COS-B from 50 to 500 MeV, which is consistent with a smooth continuation of the spectrum in hard X-rays. The emission at these energies must therefore be due to synchrotron radiation by electrons of at least PeV energies. It appears that the emission in the high-energy gamma-ray range, sensitive to the highest energy electrons in the nebula, can put interesting constraints on the acceleration mechanism.

Harding, A. K.↗
NASA NTRS1993

Development of hypersonic engine seals - Flow effects of preload and engine pressures

A new type of engine seal is being developed to meet the needs of advanced hypersonic engines. A seal braided of emerging high temperature ceramic fibers comprised of a sheath-core construction has been selected for study based on its low leakage rates. Flexible, low-leakage, high-temperature seals are required to seal the movable engine panels of advanced ramjet-scramjet engines either preventing potentially dangerous leakage into backside engine cavities or limiting the purge coolant flow rates through the seals. To predict the leakage through these flexible, porous seal structures as a function of preload and engine pressures, new analytical flow models are required. An empirical leakage resistance/preload model is proposed to characterize the observed decrease in leakage with increasing preload. Empirically determined compression modulus and preload factor are used to correlate experimental leakage data for a wide range of seal architectures. Good agreement between measured and predicted values are observed over a range of engine pressures and seal preload.

Cai, Zhong↗
NASA NTRS1993

Feedback control for unsteady flow and its application to the stochastic Burgers equation

The study applies mathematical methods of control theory to the problem of control of fluid flow with the long-range objective of developing effective methods for the control of turbulent flows. Model problems are employed through the formalism and language of control theory to present the procedure of how to cast the problem of controlling turbulence into a problem in optimal control theory. Methods of calculus of variations through the adjoint state and gradient algorithms are used to present a suboptimal control and feedback procedure for stationary and time-dependent problems. Two types of controls are investigated: distributed and boundary controls. Several cases of both controls are numerically simulated to investigate the performances of the control algorithm. Most cases considered show significant reductions of the costs to be minimized. The dependence of the control algorithm on the time-descretization method is discussed.

Choi, Haecheon↗
NASA NTRS1990

Integrated Aerodynamic and Control System Design of Oblique Wing Aircraft

An efficient high speed aircraft design must achieve a high lift to drag ratio at transonic and supersonic speeds. In 1952 Dr. R. T. Jones proved that for any flight Mach number minimum drag at a fixed lift is achieved by an elliptic wing planform with an appropriate oblique sweep angle. Since then, wind tunnel tests and numerical flow models have confirmed that the compressibility drag of oblique wing aircraft is lower than similar symmetrical sweep designs. At oblique sweep angles above thirty degrees the highly asymmetric planform gives rise to aerodynamic and inertia couplings which affect stability and degrade the aircraft's handling qualities. In the case of the NASA-Rockwell Oblique Wing Research Aircraft, attempts to improve the handling qualities by implementing a stability augmentation system have produced unsatisfactory results because of an inherent lack of controllability in the proposed design. The present work focuses on improving the handling qualities of oblique wing aircraft by including aerodynamic configuration parameters as variables in the control system synthesis to provide additional degrees of freedom with which to further decouple the aircraft's response. Handling qualities are measured using a quadratic cost function identical to that considered in optimal control problems, but the controller architecture is not restricted to full state feedback. An optimization procedure is used to simultaneously solve for the aircraft configuration and control gains which maximize a handling qualities measure, while meeting imposed constraints on trim. In some designs wing flexibility is also modeled and reduced order controllers are implemented. Oblique wing aircraft synthesized by this integrated design method show significant improvement in handling qualities when compared to the originally proposed closed loop aircraft. The integrated design synthesis method is then extended to show how handling qualities may be traded for other types of mission performance (drag, weight, etc.). Examples are presented which show how performance can be maximized while maintaining a desired level of handling quality.

Morris, Stephen James↗
NASA NTRS1993

The rheology and composition of cryovolcanic flows on icy satellites

The rheologic properties of terrestrial lavas have been related to morphologic features of their flows, such as levees, banked surfaces, multilobate structures, and compressible folds. These features also have been used to determine rheologies and constrain the compositions of extraterrestrial flows. However, with rare exceptions, such features are not resolvable in Voyager images of the satellites of outer planets. Often only flow length and edge thickness of cryovolcanic flows can be measured reasonably accurately from Voyager images. The semiempirical lava-flow model presented here is a renewed effort to extract useful information from such measurements.

Kargel, Jeffrey S.↗
NASA NTRS1993

Development of hypersonic engine seals: Flow effects of preload and engine pressures

A new type of engine seal is being developed to meet the needs of advanced hypersonic engines. A seal braided of emerging high temperature ceramic fibers comprised of a sheath-core construction was selected for study based on its low leakage rates. Flexible, low-leakage, high temperature seals are required to seal the movable engine panels of advanced ramjet-scramjet engines either preventing potentially dangerous leakage into backside engine cavities or limiting the purge coolant flow rates through the seals. To predict the leakage through these flexible, porous seal structures as a function of preload and engine pressures, new analytical flow models are required. An empirical leakage resistance/preload model is proposed to characterize the observed decrease in leakage with increasing preload. Empirically determined compression modulus and preload factor are used to correlate experimental leakage data for a wide range of seal architectures. Good agreement between measured and predicted values are observed over a range of engine pressures and seal preloads.

Cai, Zhong↗
NASA NTRS1994

Safety concerns for first entry operations of orbiting spacecraft

The Space Station Freedom crew will face operational problems unique to the spacecraft environment due to the absence of convection currents and the confined atmosphere within the habitable modules. Airborne contaminants from the materials offgassing or contingency incidents like thermodegradation may accumulate until they reach hazardous concentrations. Flow modeling and experiences from previous space flight missions confirm that caution must be exercised during first-entry operations. A review of the first-entry procedures performed during the Skylab Program will be presented to highlight the necessity for carefully planned operations. Many of the environmental conditions that can be expected on the Space Station are analogous to those which exist in confined storage or work spaces in the industrial setting. Experience with closed-loop environmental operations (e.g., atmospheric control of submarines) have also demonstrated that the buildup of trace contaminant gases could result in conditions that lead to mission termination or loss of crew. Consequently, some first-entry issues for the Station can be addressed by comparing them to familiar techniques developed on Earth. The instruments of the Environmental Health System (EHS) will provide the necessary monitoring capability to protect crew health and safety during the planned first-entry procedures of the MTC phase of the SSF Program. The authors of this paper will describe those procedures and will cite an example of the consequences when proper first-entry procedures are not followed.

Wilson, Steven H.↗