Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electron cooling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Mechanical Pumped Cooling Loop for Spacecraft Thermal Control

The Mars Pathfinder (MPF) spacecraft, scheduled for a December '96 launch to Mars, uses a mechanically pumped loop to transfer dissipated heat from the insulated lander electronics to an external radiator. This paper discusses the tradeoffs performed before choosing a mechanically pumped loop as the thermal control system for MPF. It describes the analysis, design, and predicted performance of this system. The various development tests performed are discussed along with the current status of this cooling system. Finally, some thoughts on the development of mechanically pumped loops for future spacecraft are presented.

Mars↗
DOE OSTI2022

Transmission electron microscopy study of a high burnup U-10Zr metallic fuel

To support the development of U-10 wt.% Zr (U-10Zr) metallic fuel for Gen IV sodium-cooled fast reactors, we analysed a solid, Na-bonded, U-10Zr (by weight percent) fuel cross section that was irradiated to a burnup of ~ 12.4 % at.% at the Fast Flux Test Facility (FFTF). Advanced characterization techniques, including site specific sample preparation by focused ion beam (FIB) and phase/chemical determination by transmission electron microscopy (TEM), were used to reveal the constituent redistribution of Zr, characterize the fuel phases and the secondary phases (such as solid fission products) present at the end of life. It is shown that the fuel pin cross section is divided into three major concentric zones: a Zr-rich central region, a Zr-lean intermediate region, and a Zr intermediate peripherical region. The phase characterization revealed that the irradiation environment enhanced the development and stabilization of phases not predicted by the standard equilibrium U-Zr phase diagrams. Comparing the current results with the ones from previous studies, it is reaffirmed that the irradiation temperature and the time spent in the reactor, rather than the fuel burnup, are the two factors that most influence the formation of redistribution zones and their extension along the fuel cross section. Various solid fission products precipitated inside the fission gas pores, such as lanthanides, ZrRu, BaTe, CsI, and Ba and Sr oxides. Here, this study provides unprecedented nanoscale understandings in the U-10Zr fuel system that may benefit fuel performance modelling and advanced fuel development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Do Impulsive Solar-Energetic-Electron (SEE) Events Drive High-Voltage Charging Events on the Nightside of the Moon?

When the Earth’s moon is in the supersonic solar wind, the darkside of the Moon and the lunar plasma wake can be very dangerous charging environments. In the absence of photoelectron emission (dark) and in the absence of cool plasma (wake), the emission or collection of charge to reduce electrical potentials is difficult. Unique extreme charging events may occur during impulsive solar-energetic-electron (SEE) events when the lunar wake is dominated by relativistic electrons, with the potential to charge and differentially charge objects on and above the lunar surface to very-high negative electrical potentials. In this report the geometry of the magnetic connections from the Sun to the lunar nightside are explored; these magnetic connections are the pathways for SEEs from the Sun. Rudimentary charging calculations for objects in the relativistic-electron environment of the lunar wake are performed. To enable these charging calculations, secondary-electron yields for impacts by relativistic electrons are derived. Needed lunar electrical-grounding precautions for SEE events are discussed. Calls are made 1) for future dynamic simulations of the plasma wake in the presence of time-varying SEE-event relativistic electrons and time-varying solar-wind magnetic-field orientations and 2) for future charging calculations in the relativistic-electron wake environment and on the darkside lunar surface.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1993

X ray opacity in cluster cooling flows

We have calculated the emergent x-ray properties for a set of spherically symmetric, steady-state cluster cooling flow models including the effects of radiative transfer. Opacity due to resonant x-ray lines, photoelectric absorption, and electron scattering have been included in these calculations, and homogeneous and inhomogeneous gas distributions were considered. The effects of photoionization opacity are small for both types of models. In contrast, resonant line optical depths can be quite high in both homogeneous and inhomogeneous models. The presence of turbulence in the gas can significantly lower the line opacity. We find that integrated x-ray spectra for the flow cooling now are only slightly affected by radiative transfer effects. However x-ray line surface brightness profiles can be dramatically affected by radiative transfer. Line profiles are also strongly affected by transfer effects. The combined effects of opacity and inflow cause many of the lines in optically thick models to be asymmetrical.

Wise, Michael W.↗
DOE OSTI2022

Using θ' interfaces as templates for planar L1 2 precipitation in AlCuMnZr alloys

Controlled Mn and Zr additions to Al-Cu alloys have allowed for the improved retention of mechanical properties after extended 350°C exposures by stabilizing the main strengthening θ' (Al 2 Cu) phase. Ultimately, θ'/L1 2 (Al 3 Zr) co-precipitate formation stabilizes θ' most effectively; however, Zr diffuses sluggishly and has low solubility in aluminum castings. Increasing the Zr segregation rate would allow for faster and more effective θ'/L1 2 co-precipitation. It is demonstrated that the Zr segregation rate is faster when the Zr matrix content is higher. A much higher Zr matrix content was achieved by rapid cooling during additive manufacturing (AM) that produces θ'/L1 2 co-precipitation faster, which is shown by scanning transmission electron microscopy and atom probe tomography experiments. It was also found that Zr continuously segregates to θ' interfaces up to the most aggressive heat treatment studied such that planar L1 2 precipitates remain after the metastable θ' dissolves. In this manner, we demonstrate that θ' coherent interfaces serve as perfect templates to form stable planar L1 2 precipitates that can provide strength at higher temperatures than traditional θ' strengthened AlCu alloys. This work introduces an alloy design strategy that uses metastable precipitates to quickly nucleate and grow co-precipitates with a desired geometry that contain slow diffusing elements. These ideas can be applied to engineer more heat resistant alloys by taking advantage of high solute matrix contents enabled by rapid cooling during additive manufacturing.

36 MATERIALS SCIENCE↗
NASA NTRS1997

(abstract) Mars Pathfinder Active Thermal Control System: Ground and Flight Performance of a Mechanically Pumped Cooling Loop

A key element of the Mars Pathfinder thermal control system is the Heat Rejection System (HRS). The HRS of Mars Pathfinder is designed to actively control the temperatures of the various parts of the spacecraft.This is achieved by mechanically circulating single-phase Freon 11 liquid through the lander and cruise electronics box heat exchangers and transferring the heat to an external radiator on the cruise stage. This is the first time in spacecraft history that a mechanically pumped cooling loop has been used on a long duration spacecraft mission. Many lessons have been learned during the testing and ground and flight operation of the HRS. This paper will present the performance of the mechanically pumped cooling loop during the ground and flight operations. Based on the lessons learned from this experience, recommendations on the design and operation of the pumped cooling loops for future space missions will be made.

Mars↗
DOE OSTI2023

Simulation of shell pellet injection strategies for ITER-scale tokamaks

Dispersive shell pellet (DSP) injection is considered as an alternative to shattered pellet injection as a disruption mitigation system for ITER, and strategies for penetration of a shell pellet into ITER are modeled with the 3D MHD code NIMROD. Because the high plasma temperatures lead to rapid ablation of the shell, delivery of the dispersive payload to the core of ITER will be very challenging. Two strategies to increase payload delivery depth are modeled: first, multiple staggered pellets are simulated in DIII-D, to assess the ability for one DSP to "piggy-back" on another to reach deeper into the core; second, DSP injection after pre-dilution-cooling with deuterium is simulated in ITER, in order to reduce the plasma temperature before shell pellet arrival. The DIII-D simulations show that a second, slower pellet can penetrate much deeper once the release of the first payload strongly cools the mid-radius region. When the pellets are staggered, deeper penetration of the second pellet leads to higher radiation fraction and larger runaway electron loss fraction, consistent with single pellet results. However, simultaneously released pellets at mid-radius that do not trigger a large n=1 mode produce an even higher radiation fraction. The ITER simulations show that an inside-out TQ can be produced with a payload release just inside of the q=2 surface, which is achieved at a speed of 800 m/s after pre-dilution cooling. Although stochastization of the core leads to a complete thermal quench, the edge flux surfaces are surprisingly robust in the ITER simulations, regardless of payload release location. As a result, runaway electron losses would not be expected.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Transport and optical properties of the chiral semiconductor Ag 3 AuSe 2

Previous band structure calculations predicted Ag 3 AuSe 2 to be a semiconductor with a band gap of approximately 1 eV. Here, we report single crystal growth of Ag 3 AuSe 2 and its transport and optical properties. Single crystals of Ag 3 AuSe 2 were synthesized by slow-cooling from the melt, and grain sizes were confirmed to be greater than 2 mm using electron backscatter diffraction. Optical and transport measurements reveal that Ag 3 AuSe 2 is a highly resistive semiconductor with a band gap and activation energy around 0.3 eV. Our first-principles calculations show that the experimentally determined band gap lies between the predicted band gaps from GGA and hybrid functionals. We predict band inversion to be possible by applying tensile strain. The sensitivity of the gap to Ag/Au ordering, chemical substitution, and heat treatment merit further investigation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Study of the water dynamics near hydrophilic, nanostructured CuO surfaces by quasielastic and inelastic neutron scattering

We have used quasielastic and inelastic neutron scattering to investigate the structure, dynamics, and phase transitions of water interacting with superhydrophilic CuO surfaces that not only possess a strong affinity for water but also a “grass-like” topography that is rough on both micro- and nanoscales. Here, we report quasielastic neutron scattering (QENS) measurements on two samples differing in water content at five temperatures below 280 K. The QENS spectra show water undergoing two different types of diffusive motion near the CuO surfaces: a “slow” translational diffusion occurring on a nanosecond time scale and a faster rotational motion. Further from the surfaces, there is “fast” translational diffusion comparable in rate to that of bulk supercooled water and the rotational motion occurring in the interfacial water. Analysis of the QENS spectra supports wetting of water to the CuO blades as seen in electron microscopy images. In addition, we observe an anomalous temperature dependence of the QENS spectra on cooling from 270 to 230 K with features consistent with a liquid–liquid phase transition. We suggest that the solvent-like properties of the coexisting bulk-like water in our CuO samples are a significant factor in determining the temperature dependence of the interfacial water’s dynamics. Our results are compared with those obtained from two well-studied substrate classes: (1) silicas that contain ordered cylindrical nanopores but have weaker hydrophilicity and (2) nanoparticles of other transition-metal oxides, such as TiO 2 , which share the strong hydrophilicity of our samples but lack their porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tungsten control in long pulse operation: feedback from WEST to ITER

The full W environment that is now foreseen for ITER puts strong emphasis on experimental results obtained in present devices in similar conditions. In this context, the WEST tokamak is well equipped to bring key contributions to the preparation of ITER operation, thanks to its capability to perform long pulses in dominant electron heating, torque-free scheme based on RF systems, and its ITER-grade actively cooled divertor. Recent results of interest cover the understanding of tungsten contamination and the evaluation of conditioning methods, the feedback on the current ramp-up phase, and the ageing of the ITER divertor components in L-mode attached condition. Further, new directions are being explored, in particular low divertor temperature operation that should be the normal operating regime of ITER. We also report on tungsten peaking physics, and the role of light impurity content.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1975

Hot ion plasma production in HIP-1 using water-cooled hollow cathodes

A steady-state ExB plasma was formed by applying a strong radially inward dc electric field near the mirror throats. Most of the results were for hydrogen, but deuterium and helium plasmas were also studied. Three water-cooled hollow cathodes were operated in the hot-ion plasma mode with the following results: (1) thermally emitting cathodes were not required to achieve the hot-ion mode; (2) steady-state operation (several minutes) was attained; (3) input powers greater than 40 kW were achieved; (4) cathode outside diameters were increased from 1.2 cm (uncooled) to 4.4 cm (water-cooled); (5) steady-state hydrogen plasma with ion temperatures from 185 to 770 eV and electron temperatures from 5 to 21 eV were produced. Scaling relations were empirically obtained for discharge current, ion temperature, electron temperature, and relative ion density as a function of hydrogen gas feed rate, magnetic field, and cathode voltage. Neutrons were produced from deuterium plasma, but it was not established whether thay came from the plasma volume or from the electrode surfaces.

Reinmann, J. J.↗
NASA NTRS1975

Hot ion plasma production in HIP-1 using water-cooled hollow cathodes

The paper reports on hot-ion plasma experiments conducted in a magnetic mirror facility. A steady-state E x B plasma was formed by applying a strong radially inward dc electric field near the mirror throats. Most of the results were for hydrogen, but deuterium and helium plasmas were also studied. Three water-cooled hollow cathodes were operated in the hot-ion plasma mode with the following results: (1) thermally emitting cathodes were not required to achieve the hot-ion mode; (2) steady-state operation (several minutes) was attained; (3) input powers greater than 40 kW were achieved; (4) cathode outside diameters were increased from 1.2 cm (uncooled) to 4.4 cm (water-cooled); (5) steady-state hydrogen plasmas with ion temperatures from 185 to 770 eV and electron temperatures from 5 to 21 eV were produced. Scaling relations were empirically obtained for discharge current, ion temperature, electron temperature, and relative ion density as a function of hydrogen gas feed rate, magnetic field, and cathode voltage.

Reinmann, J. J.↗
NASA NTRS1977

The plasma line revisited as an aeronomical diagnostic - Suprathermal electrons, solar EUV, electron-gas thermal balance

Spectra of plasma wave intensities in the ionosphere over Arecibo are calculated and compared with those from observations of the plasma line intensity. This approach involving directly observed quantities avoids the uncertainties that have plagued past comparisons with photoelectron theory. In addition, careful comparisons in physically relevant segments of the spectra show that any significant increase in the magnitude of the solar EUV flux would lead to a contradiction of the observed plasma wave intensities. Further, the comparisons indicate that resolution of the thermal electron-gas heat balance problem must be sought through better heat transfer rates (e.g., heating and cooling rates, etc.), rather than in the solar EUV. This approach utilizes more fully the potential of the plasma line experiment as a diagnostic tool for aeronomical studies, (e.g., photoelectrons, auroral secondaries, ionosphere-modification experiments, etc.).

Carlson, H. C., Jr.↗
NASA NTRS1980

Space shuttle main engine digital controller

The controller provides responsive control of engine thrust and mixture ratio through the digital computer in the controller, updating the instructions to the engine control elements 50 times per second (every 20 milliseconds). Additionally, precise engine performance is achieved through closed loop control, utilizing 16 bit computation, 10 bit input/output resolution, and self calibrating analog-to-digital conversion. Engine reliability is enhanced by a dual redundant control system that allows normal operation after the first failure and a fail-safe shutdown after a second failure. The digital computer is programmable, allowing modification of engine control equations and constants by change of the stored program (software). The controller is packaged in a sealed, pressurized chassis with cooling provided by convection heat transfer through pin fins as part of the main chassis. The electronics are distributed on functional modules having special provisions for thermal and vibrational protection.

Mitchell, W. T.↗
NASA NTRS1982

Bulk formation of a metallic glass - Pd40Ni40P20

Molten spheroids of Pd40Ni40P20, of up to 0.53-cm minor diameter, were slowly cooled (1.4 K/s) on a fused silica surface under 10 to the -6 torr vacuum to a form which was entirely glassy except for some superficial crystallinity comprising less than 0.5% of the volume. The occurrence of crystallization was eliminated by subjecting the specimens to surface etching followed by a succession of heating and cooling cycles. The absence of crystallization in bulk was confirmed by X-ray diffraction, transmission electron microscopy, and calorimetry. Using the last technique, the heat of crystallization of the glass was measured to be 5.3 + or - 0.3 kJ/g atom.

Drehman, A. J.↗
NASA NTRS1986

Interaction of the solar wind with interstellar neutral hydrogen - Three-fluid model

It is commonly assumed in models of the solar wind-interstellar neutral hydrogen interaction that the ionized interstellar particles are quickly assimilated into the solar wind proton population and 'become indistinguishable' from the original solar wind. This assumption leads to the prediction that the solar wind proton temperature should increase with radius in the outer heliosphere. This temperature increase has not been observed. It is pointed out that assimilation of the interstellar particles to the point of indistinguishability takes place on the very long Coulomb collision time scale, and is not expected to occur within the heliosphere. Results are presented of a three-fluid model of the solar wind which consists of comoving thermal populations of protons of solar origin, protons produced by ionization of interstellar hydrogen, and electrons. The steady-state results yield a solar wind with a 'core' proton distribution which cools adiabatically, and a 'halo' of interstellar pickup protons which is maintained near 10 to the 7th K by the energy input of continued ionization and pickup. Such a distribution will not be observed to manifest the temperature increase at large heliocentric distances which is predicted from a one-fluid analysis. Further time-dependent calculations show a strong correlation between the densities of the solar wind and the interstellar pickup protons. It is suggested that the interstellar pickup population may be observable by the Voyager plasma instruments in low resolution mode during periods of high solar wind density and low solar wind temperature.

Isenberg, P. A.↗
NASA NTRS1992

Global spectroscopy and imaging of atmospheric X-ray bremsstrahlung - Instrumentation and initial results from the PEM/AXIS instrument aboard the Upper Atmosphere Research Satellite

The Atmospheric X-ray Imaging Spectrometer (PEM/AXIS) aboard NASA's Upper Atmosphere Research Satellite provides continuous horizon to horizon images, both day and night, of the 3- to 100-keV X-ray flux emitted from the top of the atmosphere. AXIS achieves a spatial resolution to better than 100 km using a one-dimensional array of 16 passively cooled silicon detectors. The primary purpose of this instrument is to provide a global monitor of electron energy input to the upper atmosphere. We describe the design, development, and calibration of AXIS and provide an assessment of its excellent on-orbit performance. The unique capabilities of X-ray imaging spectrometers are demonstrated through an analysis of specific examples from October and November 1991. Important new developments for follow-on instruments also will be described.

Chenette, D. L.↗