Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXPLOSIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Experimental investigation on the energy deposition and morphology of the electrical explosion of copper wire in vacuum

This paper presents the experimental results of the electrical explosion of copper wires in vacuum using negative nanosecond-pulsed current with magnitude of 1–2 kA. The 20 μm-diameter copper wires with different lengths are exploded with three different current rates. A laser probe is applied to construct the shadowgraphy and interferometry diagnostics to investigate the distribution and morphology of the exploding product. The interference phase shift is reconstructed from the interferogram, by which the atomic density distribution is calculated. Experimental results show that there exist two voltage breakdown modes depending on the amount of the specific energy deposition. For the strong-shunting mode, shunting breakdown occurs, leading to the short-circuit-like current waveform. For the weak-shunting mode with less specific energy deposition, the plasma generated during the voltage breakdown is not enough to form a conductive plasma channel, resulting in overdamped declining current waveform. The influence of the wire length and current rate on the characteristics of the exploding wires is also analyzed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2016

Ag-ZnO nanostructure for ANTA explosive molecule detection

Ag/ZnO nanostructure for surface enhanced Raman scattering application in the detection of ANTA explosive molecule is demonstrated. A highly rough ZnO microstructure was achieved by rapid thermal annealing of metallic Zn film. Different thickness Ag nanostructures are decorated over these ZnO microstructures by ion beam sputtering technique. Surface enhanced Raman spectroscopic studies carried out over Ag/ZnO substrates have shown three orders higher enhancement compared to bare Ag nanostructure deposited on the same substrate. The reasons behind such huge enhancement are discussed based on the morphology of the sample.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2016

Laser-initiated explosive electron emission from flat germanium crystals

Flat Sb-doped germanium (100) crystals were investigated in the triode configuration under pulsed tunable laser illumination (pulse duration t{sub laser} = 3.5 ns and photon energy hν = 0.54–5.90 eV) and under DC voltages <10{sup 4} V. Large bunch charges up to ∼1 μC were extracted from the cathodes for laser pulses >1 MW/cm{sup 2} corresponding to a high quantum efficiency up to 3.3% and cathode currents up to 417 A. This laser-induced explosive electron emission (EEE) from Ge was characterized by its voltage-, laser power- and hν-sensitivity. The analysis of the macroscopic surface damage caused by the EEE is included as well. Moreover, we have carried out first direct measurements of electron energy distributions produced during the EEE from the Ge samples. The measured electron spectra hint for electron excitations to the vacuum level of the bulk and emission from the plasma plume with an average kinetic energy of ∼0.8 eV.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2017

Characterization of detonation soot produced during steady and overdriven conditions for three high explosive formulations

The detonation of high explosives (HE) produces a dense fluid of molecular gases and solid carbon. The solid detonation carbon contains various carbon allotropes such as detonation nanodiamonds, onion-like carbon, graphite and amorphous carbon, with the formation of the different forms dependent upon pressure, temperature and the environmental conditions of the detonation. We have collected solid carbon residues from controlled detonations of three HE formulations (Composition B-3, PBX 9501, and PBX 9502). Soot was collected from experiments designed to produce both steady and overdriven conditions, and from detonations in both an ambient (air) atmosphere and in an inert Ar atmosphere. Differences in solid carbon residues were quantified using X-ray photoelectron spectroscopy and carbon isotope measurements. Environmental conditions, HE formulation, and peak pressures influenced the amount of and isotopic composition of the carbon in the soot. Detonations in an Ar atmosphere produced greater amounts of carbon soot with lower δ 13 C values than those in ambient air. Therefore, solid carbon residues continued to evolve after detonation due to excess oxygen in the ambient air detonations. As well, higher peak pressures in overdriven conditions produced less carbon soot with, in general, higher δ 13 C values. Consequently, while overdriven conditions only produced peak pressures for a limited duration, it was enough to influence the composition of the solid carbon residues.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Temperature of shocked plastic bonded explosive PBX 9502 measured with spontaneous Stokes/anti-Stokes Raman

Raman spectra and velocimetry of shocked PBX 9502 (plastic bonded explosive composed of 95% triaminotrinitrobenzene (TATB) and 5% 3M Company Kel F-800 polymer binder) are reported with the Stokes/anti-Stokes ratio used to determine temperature after the shock reflects from a lithium fluoride window. Final pressures up to 14.5 GPa were tested, but the pressure induced absorption of TATB caused the Raman signal to decrease exponentially with pressure. The reflected shock temperature could be determined to 7 GPa, with an average increase of 14.9 K/GPa. Suggestions to adapt the technique to permit thermometry at higher temperatures are discussed, as are comparisons to a recently proposed equation of state for PBX 9502.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Reactive flow modeling of the polymer bonded explosive LX-17 double shock experiments

Overdriven double shock experiments provide a measurement of the properties of the reaction product states of the 1-3-5-triamino-2-4-6trinitrobenzene-based explosive LX-17. These experiments used two flyer materials mounted on the end of a projectile to send an initial shock through the LX-17, followed by a second shock of a higher magnitude into the detonation products. The experimental results are compared to 2D reactive flow modeling. A reactive flow model that describes only the kinetics of the LX-17 decomposition fails to accurately reproduce the decay of the first shock or the curvature or strength of the second shock. A new model is proposed in which the carbon condensate produced in the reaction zone is controlled by a kinetic rate. This allows the carbon condensate to be initially out of chemical equilibrium with the product gas. Finally, this new model reproduces the initial detonation peak and decay and matches the curvature of the second shock; however, it still over-predicts the strength of the second shock.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Novel PBX formulations containing thermally-expandable microspheres for on-demand control of explosive behavior

In this work, we present the formulation and analysis of inert Plastic-Bonded eXplosive (PBX)-surrogates loaded with thermally expandable microspheres (TEMs). TEMs consist of a thermoplastic acrylonitrile shell (10-50 µm diameter) encapsulating an inert low boiling hydrocarbon. Upon heating, the TEMs expand as the shell softens while the hydrocarbon gasifies, increasing the internal pressure and expanding the particle by as much as 120 vol%. We hypothesize that TEM expansion within a PBX will introduce tunable changes in local density and porosity, and ultimately the shock sensitivity. This paper focuses on microstructural analysis of surrogate PBX-TEM formulations, both before and after thermally- induced TEM expansion. The formulations were analyzed by scanning electron microscopy (SEM), ultra-small angle neutron scattering (USANS), and X-ray Computed Tomography (x-ray CT) under various thermal conditions. Evidence suggests that TEM expansion within a PBX is a viable method to impart microstructural changes that are predicted to have a measurable, on-demand effect on the initiation sensitivity. Future work includes development of PBX-TEM formulations with HMX and shock initiation experiments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Kinetics of Carbon Condensation in Detonation of High Explosives: First-Order Phase Transition Theory Perspective

We report the kinetics of carbon condensation, or carbon clustering, in detonation of carbon-rich high explosives is modeled by solving a system of rate equations for concentrations of carbon particles. Unlike previous efforts, the rate equations account not only for the aggregation of particles but also for their fragmentation in a thermodynamically consistent manner. Numerical simulations are performed, yielding the distribution of particle concentrations as a function of time. In addition to that, analytical expressions are obtained for all the distinct steps and regimes of the condensation kinetics, which facilitates the analysis of the numerical results and allows one to study the sensitivity of the kinetic behavior to the variation of system parameters. The latter is important because the numerical values of many parameters are not reliably known at present. The theory of the kinetics of first-order phase transitions is found adequate to describe the general kinetic trends of carbon condensation, as described by the rate equations. Such physical phenomena and processes as the coagulation, nucleation, growth, and Ostwald ripening are observed, and their dependence on various system parameters is studied and reported. It is believed that the present work will become useful when analyzing the present and future results for the kinetics of carbon condensation, obtained from experiments or atomistic simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Flash x-ray radiography analysis of detonation wave propagation in additive-manufactured high explosives

Recent research has demonstrated that additive manufacturing (AM) can be used to produce directionally sensitive high explosives (HEs), but detonation wave propagation in AM HEs with variable internal structure has not been studied. In this work, samples were printed using a 73 wt. % octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine-based HE ink. Flash x-ray radiography imaging was used to observe density changes in two imaging planes of each sample during detonation, and high-speed imaging was used to calculate the detonation velocity at the HE surface. The detonation front initially appears to fail in internal channel regions of the HE, but late reactions occurred in two samples, which increased the material bulk density by 2.8%, possibly due to shock convergence phenomena. The calculated detonation wave pressure similarly increased, but the accuracy of the results is uncertain because of the deviation of the low bulk density printed samples from the cast charge principal isentrope. Here, this work demonstrates that structure can be effectively utilized to guide detonation wave propagation through HE charges.

3D printing↗
DOE OSTI2023

Validation of a detonation product equation of state for an insensitive high explosive via slab geometry expansion tests

Slab expansion (SLABEX) tests are conducted to validate a process for calibrating the detonation products equation of state (EOS) of a high explosive (HE). The SLABEX tests use rectangular slabs of PBX 9502, a polymer-bonded HE formulation consisting of 95 wt.% 1,3,5-triamino-2,4,6-trinitrobenzene bound with Kel F-800, a co-polymer of chlorotrifluoroethylene and vinylidene-fluoride. Three PBX 9502 slab thicknesses are examined, each confined symmetrically by two rectangular copper (Cu) plates approximately one-tenth the thickness of the HE slab. For the duration of each experiment, the detonation flow along the central axis of the PBX 9502 slab remains two-dimensional. The lateral flow velocity component of the outer surfaces of the expanding Cu plates is measured, along with the steady axial detonation speed along the central axis of the SLABEX. Hydrodynamic simulations of the Cu plate expansion in the SLABEX geometry, driven by the energy stored in the detonation products by the detonation combustion event, are conducted using a Jones–Wilkins–Lee EOS for the detonation products. This EOS form was recently parameterized for PBX 9502 in the cylinder expansion test geometry using a newly developed calibration technique [Voelkel et al., Combust. Flame 246, 112373 (2022)]. Good agreement between the experiment and prediction is found in each SLABEX test, demonstrating that the detonation product EOS calibration technique produces EOSs that are predictive when applied to other geometries.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2023

Uncertainty quantification for high explosive reactant and product equations of state

Equations of state (EOSs) are typically represented as physics-informed models with tunable parameters that are adjusted to replicate calibration data as closely as possible. Uncertainty quantification (UQ) allows for the development of an ensemble of EOS parameters that are consistent with the calibration data instead of a single EOS. In this work, we perform UQ for the reactant and product EOSs for a variety of high explosives (HEs). In doing so, we demonstrate a strategy for dealing with heterogeneous (both experimental and calculated) data. We also use a statistical distance metric to quantify the differences between the various HEs using the UQ results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Modification of Richtmyer–Meshkov instabilities via layered explosive charge design

In this numerical study, we investigate the effects of layered high explosive (HE) charge design on Richtmyer–Meshkov instability (RMI) in metal plates with sinusoidal surface features. The detonation wave from the HE induces a shock in the metal target that subsequently interacts with the surface features; this results in vortex formation and ultimately RMI. Here, we seek to modify RMI by altering the detonation wave characteristics. The modification is investigated in a twofold manner: first, by varying the initial design of the unconfined surface of the target and second, by varying the charge design and composition. Within a limited scope of this design space, a wide variety of behaviors related to RMI growth are observed. Mechanistic actions, including exaggerated front curvature, behind these modifications are proposed. Charge designs, which modify RMI the most for a select target design, are then presented.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2024

Measuring thermal profiles in high explosives using neural networks

We present a new method for calculating the temperature profile of high explosive (HE) material using a Convolutional Neural Network (CNN). To train/test the CNN, we have developed a hybrid experiment/simulation method for collecting acoustic and temperature data. We experimentally heat cylindrical containers of HE material until detonation/deflagration, where we continuously measure the acoustic bursts through the HE using multiple acoustic transducers lined around the exterior container circumference. However, measuring the temperature profile in the HE in an experiment would require inserting a large number of thermal probes, which would disrupt the heating process. Thus, we use two thermal probes, one at the HE center and one at the wall. We then use numerical simulation of the heating process to calculate the temperature distribution and correct the simulated temperatures based on the experimental center and wall temperatures. We calculate temperature errors on the order of 15 °C, which is ∼12% of the range of temperatures in the experiment. We also investigate how the algorithm’s accuracy is affected by the number of acoustic receivers used to collect each measurement and the resolution of the temperature prediction. This work provides a means of assessing the safety status of HE material, which cannot be achieved using existing temperature measurement methods. In addition, it has implications for a range of other applications where internal temperature profile measurements would provide critical information. These applications include detecting chemical reactions, observing thermodynamic processes such as combustion, monitoring metal or plastic casting, determining the energy density in thermal storage capsules, and identifying abnormal battery operations.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Grid resolution requirement of chemical explosive mode analysis for large eddy simulations of premixed turbulent combustion

Full Article Figures & data References Citations Metrics Reprints & Permissions Read this article Abstract The grid resolution requirement for trustworthy Chemical Explosive Mode Analysis (CEMA) in Large Eddy Simulation (LES) of premixed turbulent combustion is proposed. Explicit filtering, to emulate the effect of the LES filter, is applied to one-dimensional laminar flame and three-dimensional planar turbulent flames across a wide range of Karlovitz numbers (5 - 239). The identification of the flame front by CEMA is found relatively insensitive to the cell size (Δ), while the combustion mode identification shows more significant sensitivity. Specifically, increasing Δ falsely enhances the auto-ignition and local extinction modes and suppresses the diffusion-assisted mode. Limited dependence of the CEMA performance on the turbulent combustion regime (Karlovitz number) is observed. A simple grid size criterion for reliable CEMA mode identification in LES is proposed as Δ ≲ δ L /2; The criterion can be relaxed to Δ ≲ δ L in the laminar flame limit. Furthermore, theoretical analysis is conducted on an idealised chemistry-diffusion system. The effects of the filtering process and turbulence on the local combustion mode are demonstrated, which is consistent with the numerical observations. Further, by incorporating turbulent combustion models in CEMA, potential improvement in identifying local combustion modes can be expected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Type Ia supernova rate measurements to redshift 2.5 from CANDELS: Searching for prompt explosions in the early universe

The Cosmic Assembly Near-infrared Deep Extragalactic Legacy Survey (CANDELS) was a multi-cycle treasury program on the Hubble Space Telescope (HST) that surveyed a total area of ∼0.25 deg{sup 2} with ∼900 HST orbits spread across five fields over three years. Within these survey images we discovered 65 supernovae (SNe) of all types, out to z ∼ 2.5. We classify ∼24 of these as Type Ia SNe (SNe Ia) based on host galaxy redshifts and SN photometry (supplemented by grism spectroscopy of six SNe). Here we present a measurement of the volumetric SN Ia rate as a function of redshift, reaching for the first time beyond z = 2 and putting new constraints on SN Ia progenitor models. Our highest redshift bin includes detections of SNe that exploded when the universe was only ∼3 Gyr old and near the peak of the cosmic star formation history. This gives the CANDELS high redshift sample unique leverage for evaluating the fraction of SNe Ia that explode promptly after formation (<500 Myr). Combining the CANDELS rates with all available SN Ia rate measurements in the literature we find that this prompt SN Ia fraction is f{sub P} = 0.53{sub stat0.10}{sup ±0.09}{sub sys0.26}{sup ±0.10}, consistent with a delay time distribution that follows a simple t {sup –1} power law for all times t > 40 Myr. However, mild tension is apparent between ground-based low-z surveys and space-based high-z surveys. In both CANDELS and the sister HST program CLASH (Cluster Lensing And Supernova Survey with Hubble), we find a low rate of SNe Ia at z > 1. This could be a hint that prompt progenitors are in fact relatively rare, accounting for only 20% of all SN Ia explosions—though further analysis and larger samples will be needed to examine that suggestion.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2013

Discovery of a new kind of explosive X-ray transient near M86

We present the discovery of a new type of explosive X-ray flash in Chandra images of the old elliptical galaxy M86. This unique event is characterized by the peak luminosity of 6 × 10{sup 42} erg s{sup –1} for the distance of M86, the presence of precursor events, the timescale between the precursors and the main event (∼4000 s), the absence of detectable hard X-ray and γ-ray emission, the total duration of the event, and the detection of a faint associated optical signal. The transient is located close to M86 in the Virgo cluster at the location where gas and stars are seen protruding from the galaxy probably due to an ongoing wet minor merger. We discuss the possible mechanisms for the transient and conclude that the X-ray flash could have been caused by the disruption of a compact white dwarf star by a ∼10{sup 4} M {sub ☉} black hole. Alternative scenarios such that of a foreground neutron star accreting an asteroid or the detection of an off-axis (short) γ-ray burst cannot be excluded at present.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2015

SPIRAL INSTABILITY CAN DRIVE THERMONUCLEAR EXPLOSIONS IN BINARY WHITE DWARF MERGERS

Thermonuclear, or Type Ia supernovae (SNe Ia), originate from the explosion of carbon–oxygen white dwarfs, and serve as standardizable cosmological candles. However, despite their importance, the nature of the progenitor systems that give rise to SNe Ia has not been hitherto elucidated. Observational evidence favors the double-degenerate channel in which merging white dwarf binaries lead to SNe Ia. Furthermore, significant discrepancies exist between observations and theory, and to date, there has been no self-consistent merger model that yields a SNe Ia. Here we show that a spiral mode instability in the accretion disk formed during a binary white dwarf merger leads to a detonation on a dynamical timescale. This mechanism sheds light on how white dwarf mergers may frequently yield SNe Ia.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

New constraints on the Al 25 ( p , γ ) reaction and its influence on the flux of cosmic γ rays from classical nova explosions

The astrophysical 25 Al(p,γ) 26 Si reaction represents one of the key remaining uncertainties in accurately modeling the abundance of radiogenic 26 Al ejected from classical novae. Specifically, the strengths of key proton-unbound resonances in 26 Si, that govern the rate of the 25 Al(p,γ) reaction under explosive astrophysical conditions, remain unsettled. Here, we present a detailed spectroscopy study of the 26 Si mirror nucleus 26 Mg. We have measured the lifetime of the 3 + , 6.125-MeV state in 26 Mg to be 19(3) fs and provide compelling evidence for the existence of a 1 – state in the T = 1, A = 26 system, indicating a previously unaccounted for ℓ = 1 resonance in the 25 Al(p,γ) reaction. Using the presently measured lifetime, together with the assumption that the likely 1 – state corresponds to a resonance in the 25 Al + p system at 435.7(53) keV, we find considerable differences in the 25 Al(p,γ) reaction rate compared to previous works. Furthermore, based on current nova models, we estimate that classical novae may be responsible for up to ≈ 15% of the observed galactic abundance of 26 Al.

20 ≤ A ≤ 38↗