Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXPERIMENTAL REACTORS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Post Irradiation Examination of Pressurized Water Reactor Stainless Steel Internal Components

Internal structural components of pressurized water reactors (PWR), such as baffle former bolts, are subjected to significant neutron irradiation and mechanical stresses at elevated temperatures during plant operation. Over the long operation of the power plant, these conditions lead to potential degradation and reduced load-carrying capacity of these bolts. To understand property degradation more fully, to confirm the results of experimental irradiation programs, and to predict operational lifetime performance of structural materials in internal components, post irradiation examination of harvested materials from operating nuclear reactors is required. In this work, two high fluence 316 stainless steel baffle former bolts were retrieved from a commercial Westinghouse two-loop downflow type PWR and then sectioned for analysis via mechanical testing and microstructural characterization. The irradiation damage fluctuated along the bolt length with damage levels from 15 to 41 displacements per atom with the bolt head receiving approximately twice the neutron damage levels as that of the bolt thread section. Mechanical testing evaluations showed extensive irradiation hardening and a sharp decrease in fracture toughness in all parts of the bolt, though with limited variation along the bolt length. Microstructural characterization using analytical scanning transmission electron microscopy and atom probe tomography showed significant radiation induced precipitation, segregation, and dislocation loop and cavity formation. However, unlike the mechanical behavior, there was considerable variation along the bolt length but opposite of what may be expected, with more precipitation and cavity formation in the bolt thread where the neutron radiation dose is less than in the bolt head where the neutron radiation dose is higher. The cause of this variation is likely due to gradients in temperature, neutron energy spectra, and gamma irradiation.

Lach, Tim↗
DOE OSTI2025

IER 516 - Zirconium Test Assembly (ZTA) Preliminary Experimental Design [Slides]

Zirconium present in large quantities in criticality safety applications such as fuel manufacturing and processing facilities, and in commercial thermal nuclear reactors. ICSBEP lacks benchmarks optimized for zirconium sensitivity to validate zirconium evaluations. Evaluators lack isotopic differential nuclear data in regions of high importance to fission systems.

K-PSO 2.0↗
DOE OSTI2025

Benchmark Exercise Report for Experimental Study of Bubble Scrubbing in Water Coolant Pool

Mechanistic assessments of radionuclide release during postulated accidents are expected to be included in advanced reactor license applications. The mechanistic source term (MST) provides an opportunity for vendors to realistically evaluate the radiological consequences of an incident, and may aid in justifying reduced emergency planning zones and plant sites. However, the development of MSTs for advanced nuclear reactors is challenging because there are numerous phenomena that can affect the transport and retention of radionuclides. As part of a trial MST assessment for a metal-fueled, pool-type sodium cooled fast reactor (SFR), led by Argonne National Laboratory, a simplified radionuclide transport code (SRT code) was developed, which includes models to estimate the quantity of fission product aerosols scrubbed in the sodium pool during postulated accident scenarios. In a pool-type SFR, when fission products are released into the coolant pool due to failure of fuel pins, most of the radionuclides are scrubbed by the coolant pool, but some have the potential to migrate to the cover gas region through entrainment within gas bubbles. The SRT code contains a model that evaluates this scrubbing behavior and calculates the fraction of fission product aerosols that reach the cover gas. Due to a lack of available validation data for sodium pool scrubbing, the U.S. Department of Energy funded an experiment at the University of Wisconsin-Madison to measure aerosol scrubbing by injecting air bubbles containing aerosol into a coolant pool. Prior to performing an experiment with liquid sodium, a water loop experiment was performed. Their experiment evaluated the effect of changing the aerosol size, aerosol density, aerosol concentration, bubble size, and pool depth on the aerosol scrubbing efficiency of the pool. In this benchmark experiment, the base tests were conducted by repeated tests of isolated bubbles. Afterwards, more prototypic tests with bubble swarms were performed to evaluate the interactions between the bubbles. The bubble swarm test was able to confirm that a larger amount of aerosol scrubbing occurred than the single bubble test. It was also confirmed that as the bubble size, aerosol density, and pool height increase, the extent of pool scrubbing also increases and does not change with the aerosol concentration. In addition, since the degree of scrubbing is the lowest at aerosol sizes between 0.01 and 1 μm, that is, the largest amount of aerosol is emitted, it was confirmed that the analysis of this size in MST is the most important. This benchmark experiment informs the direction of future sodium experiments.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

The CWS Experiments – An Experimental Study of the Effects of Chlorine on Thermal Neutron Absorption

The Chlorine Worth Study (CWS) experiments consist of layers of Zero Power Physics Reactor plates moderated by high density polyethylene, polyvinyl chloride, and chlorinated polyvinyl chloride with the goal to produce a thermal critical experiment. A thick high density polyethylene reflector surrounds the experiments. Aluminum fuel trays and frames were used to conduct the intrinsic heat generation of the plutonium plates away from the core and out to the top plate and the platen, both acting as heat sinks. The goal of the CWS experiments was to provide benchmark critical experiments that were sensitive to chlorine and matched the sensitivity of criticality safety applications for aqueous chloride operations at PF-4 at Los Alamos National Laboratory. The specific aqueous chloride PF-4 applications were solutions of 30 g/L plutonium, 300 g/L plutonium, and 600 g/L plutonium. The CWS experiments were designed using prototype methods developed by the ARCHIMEDES and EUCLID projects at Los Alamos National Laboratory. The CWS experiments were performed in December of 2021 at the National Criticality Experiments Research Center at the Nevada Nuclear Security Site on the Planet critical assembly. It is intended that the CWS experiments will be evaluated and submitted to the ICSBEP in the future as criticality safety benchmarks.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Air-Cooled RCCS CFD Modeling Validation 2025

Slide deck for the Advanced Reactor Technologies Gas Cooled Reactor (ART-GCR) program review. The slides show the progress on the air-cooled reactor cavity cooling system (RCCS) CFD validation work. The validation of the air-cooled RCCS is performed using the experimental facility at the University of Wisconsin-Madison. The slide deck provides a progress update on this year's achievements. The natural convection tests under uniform power are modeled and compared with the experimental results. The results show good agreement with the experimental results. A sensitivity study on the RANS turbulence models is performed. Additionally, the contribution of radiative and convective heat transfer within the heated cavity is calculated and compared to forced convection setups.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

A separations and purification process for improving yields and meeting fuel contaminant specifications for high-octane gasoline produced from dimethyl-ether over a Cu/BEA catalyst

In this work, we have been developing a three-step conversion of biomass-derived syngas to methanol to dimethyl-ether (DME) to non-aromatic hydrocarbons for use as high-octane gasoline and sustainable aviation fuel. This process produces branched alkanes from DME using a Cu/BEA catalyst and is a promising alternative to other syngas conversion processes such as Fischer-Tropsch to linear alkanes and traditional ZSM-5 catalyzed methanol to aromatic gasoline. In this short article we describe some advances in our understanding related to separations and purification via the use of more detailed experimental speciation in an updated process model involving multiple phase equilibrium-based separation steps. Primary modeled reactor outlet constituents (and weight %) are: C3 and lighter hydrocarbon gases (11.1%), C4s (54.5%), H 2 (1.2%), CO 2 (2.9%), water (5.0%), unreacted DME (16.5%), methanol (2.3%), and C5+ hydrocarbons (6.4%). DME (the primary reactant) and H 2 recycle and reuse are important for the overall process efficiency, and the recycle of C4s is important to increase the C5+ yield via reactivation and homologation. Thus H 2 , C4s, and DME are targeted for recycle, while methanol and water need to be removed from the product to conform with fuel specifications. Model predictions from Aspen Plus using the NRTL-RK property method indicate a fuel composition with C5+ content of 97.1 wt%, with minor constituents: 2.4 wt% C4s, 0.3 wt% methanol, 0.1 wt% DME, 0.03 wt% water, and 0.01 wt% C3s. These ranges of minor components conform with fuel quality requirements, and the modeled product is amenable for unconstrained blending to boost gasoline octane ratings.

09 BIOMASS FUELS↗
DOE OSTI2026

A robust alloy design (RAD) strategy for next-generation (IV) nuclear fission reactors

Next-generation nuclear reactors demand structural materials capable of withstanding extreme conditions, including high temperatures, intense neutron flux, and corrosive environments. Multi-Principal Element Alloys (MPEAs) have emerged as promising candidates due to their exceptional radiation tolerance, thermal stability, and compositional flexibility. This study introduces a versatile and customizable Robust Alloy Design (RAD) strategy for systematically designing MPEAs for GEN-IV reactor fuel cladding. The RAD framework integrates nuclear-relevant selection criteria, empirical parameter assessments, and high-throughput CALPHAD simulations to efficiently narrow compositional space and identify stable alloys. A unified RAD score developed for the first time, combines key performance metrics, including fuel-clad chemical interaction (FCCI), neutron absorption cross-section (NAC), valence electron configuration (VEC), and melting point factor (MPF), into a flexible ranking system adaptable to reactor-specific priorities. Among 724 candidates, V555(5Al–5Cr–5Fe–85V) emerged as the top alloy, validated experimentally with a homogeneous single-phase BCC microstructure and superior mechanical properties (nano-indentation: 3.389 ± 0.258 GPa; Vickers hardness: 240 ± 6.7 HV), significantly outperforming Zircaloy-4 and V-4Cr-4Ti. Importantly, the RAD strategy is not limited to nuclear applications; its customizable weighting system enables scalability to other extreme environments. This adaptability positions RAD strategy as a versatile tool for advanced materials design across multiple industries.

Alloy design↗
DOE OSTI2023

Physical and technical basis of Materials Plasma Exposure eXperiment from modeling and Proto-MPEX results *

Abstract The Materials Plasma Exposure eXperiment (MPEX) is a steady-state linear plasma device that will address plasma-material interaction (PMI) science and enable testing of fusion reactor-relevant divertor plasma-facing materials. The MPEX source concept consists of a helicon plasma source to generate the plasma, electron cyclotron heating (ECH) for electron heating, and ion cyclotron heating (ICH) for ion heating. The MPEX source plasma is then transported axially to the PMI material target region to test material samples in fusion reactor-relevant divertor conditions. This paper will summarize the physical and technical basis of MPEX. The paper will first define the MPEX parameters and scenarios at the target relevant to PMI science for various fusion reactor-relevant divertor conditions and show plasma transport modeling results to set the MPEX source parameters. Recent experimental and modeling results from Proto-MPEX, a short-pulse experiment to develop the plasma production, heating, and transport physics for MPEX, will be shown. From these results, it will be shown that MPEX can reach its desired scenarios. The MPEX physical and technical basis will also determine important functional requirements for magnetic field, radiofrequency (RF) power, RF frequency, and neutral pressure in the helicon, ECH, ICH, and PMI regions that are required to achieve the desired MPEX scenarios. The necessity for key in-vessel components such as skimmers, limiters, and microwave absorbers will also be highlighted.

Lau, C. (ORCID:0000000285765867)↗
DOE OSTI2024

J-TEXT achievements in turbulence and transport in support of future device/reactor

Following the reconstruction of the TEXT tokamak at Huazhong University of Science and Technology in China, renamed as J-TEXT, a plethora of experimental and theoretical investigations has been conducted to elucidate the intricacies of turbulent transport within the tokamak configuration. These endeavors encompass not only the J-TEXT device's experimental advancements but also delve into critical issues pertinent to the optimization of future fusion devices and reactors. Here, the research includes topics on the suppression of turbulence, flow drive and damping, density limit, non-local transport, intrinsic toroidal flow, turbulence and flow with magnetic islands, turbulent transport in the stochastic layer, and turbulence and zonal flow with energetic particles or helium ash. Several important achievements have been made in the last few years, which will be further elaborated upon in this comprehensive review.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Proposal for a Fusion Prototype Neutron Source at the Los Alamos Neutron Science Center

This study evaluates a target station at the Los Alamos Neutron Science Center dedicated to the mission of irradiating structural materials in an environment that is nearly prototypic of the radiation environment experienced by the first wall of a magnetically-confined fusion reactor burning D-T fuel. Such a station could be located in the existing Area A experimental hall and be driven by an 800-MeV, 1-MW proton beam delivered by the LANSCE accelerator. A neutronics assessment of a target concept shows it satisfies all of the key parameter guidelines stated in the Summary Report on the Fusion Prototypic Neutron Source Workshop.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

USHPRR MP-1 Irradiation Test: Assessment of Edge Pitting and Bond Line Corrosion in Vendor Produced Fuel Plates

This report summarizes an effort to identify the source of anomalous localized edge pitting and bond line corrosive attack of experimental mini fuel plates manufactured at the commercial fuel vendor BWXT and tested in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) as part of the Miniplate 1 (MP-1) irradiation test. The MP-1 test was conducted by the US High Performance Research Reactor Project (USHPRR) and overseen by the Fuel Qualification Pillar (FQ). The test involved evaluation of a mix of 62 “vendor” fuel plates fabricated at BWXT and 12 “laboratory” fuel plates fabricated at Idaho National Laboratory using commercial-scale and labscale fabrication processes respectively. The MP-1 test was the first in a series of tests to generate data to support qualification of a new plate-type low-enriched uranium (LEU) U-10Mo monolithic fuel system. The major objective of the MP-1 experiment was to test, for the first time, miniplates fabricated by a commercial fuel vendor over the range of irradiation conditions relevant to conversion of NRC regulated High Performance Research Reactors (HPRRs) from high-enriched uranium to LEU. The focus of the efforts described in this report are the vendor fuel plates to inform changes in the fabrication process prior to fabrication of the next miniplate experiment MP2.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Updating and Refining BISON TRISO Assessment

Several advanced reactor concepts consider tristructural isotropic (TRISO) fuel in their designs. To support the advanced reactor industry, the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program within the U.S. Department of Energy (DOE) is developing modeling and simulation capabilities within the BISON fuel performance code. Assessment of these capabilities against available experi- mental data, such as the Advanced Gas Reactor (AGR) program, is essential in instilling confidence in the code predictions. Associated uncertainties in model inadequacy, experimental measurements, and manufacturing are also of importance. This report discusses the updating and standardization of the existing assessment suite in BISON for TRISO fuel performance analysis. The cases considered the AGR-1, AGR-2, and AGR-3/4 experimental programs. The report also includes a preliminary investigation into the sources of model inadequacy associated with silver (Ag) release fractions using the AGR-2 Compact 2-1-2 as a case study. The results indicate that uncertainties in the operating temperatures supplied to the model and the form of those temperature conditions (spatially averaged versus spatially resolved) both affect Ag release predictions. This suggests that previously observed model inadequacy can be attributed to both physical models and the operating conditions supplied to them. These findings will be leveraged to guide development of assessment cases for additional experiments and refinement of physical models for behaviors that potentially influence Ag release, such as palladium penetration.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1975

Flame stability in combusting turbulent jets

A simplified theoretical model for turbulent methane/air flames from a subscale power plant burner is developed and applied to predict the stability of flames as a function of (1) ambient atmosphere temperature and composition, (2) initial preheat temperature, and (3) percentage of external product gas recirculation. The flame model equates the rate at which mass is supplied per unit volume to the rate it is chemically reacted per unit volume using a one-step reaction and a perfectly stirred reactor (PSR). The model contains a free parameter which is evaluated by comparing the theoretical results to experimental results available in the literature. The stability results show that premixed, turbulent flames are stable over a wide equivalence ratio range if the ambient gas is air; however, if combustion products are entrained, the stability is sharply reduced.

Nelson, H. F.↗
NASA NTRS1991

Particle orbits in a rotating liquid

The motion of small spherical particles under gravity, in a viscous fluid rotating uniformly about a horizontal axis, is investigated. Formulations and solutions are obtained for the particle orbit problem and the rotation rate optimization problem. It was found that the rotation rate which maximizes the fraction of the reactor cross-section area containing particles that will not spiral out to the wall in the experimental time (for heavy particles), or that have spiraled inward without hitting the wall (for light particles) is close to 1 rpm.

Roberts, Glyn O.↗
NASA NTRS1959

Two-Dimensional Diffusion Theory Analysis of Reactivity Effects of a Fuel-Plate-Removal Experiment

Two-dimensional two-group diffusion calculations were performed on the NASA reactor simulator in order to evaluate the reactivity effects of fuel plates removed successively from the center experimental fuel element of a seven- by three-element core loading at the Oak Ridge Bulk Shielding Facility. The reactivity calculations were performed by two methods: In the first, the slowing-down properties of the experimental fuel element were represented by its infinite media parameters; and, in the second, the finite size of the experimental fuel element was recognized, and the slowing-down properties of the surrounding core were attributed to this small region. The latter calculation method agreed very well with the experimented reactivity effects; the former method underestimated the experimental reactivity effects.

Gotsky, Edward R.↗
NASA NTRS2000

Simulation and Experimental Measurements of Inductively Coupled CF4 and CF4/Ar Plasmas

The recently developed code SEMS (semiconductor equipment modeling software)is applied to the simulation of CF4 and CF4/Ar inductively coupled plasmas (ICP). This work builds upon the earlier nitrogen, transformer coupled plasma (TCP) SEMS research by demonstrating its accuracy for more complex reactive mixtures, moving closer to the realization of a virtual plasma reactor. Attention is given to the etching of and/or formation of carbonaceous films on the quartz dielectric window and diagnostic aperatures. The simulations are validated through comparisons with experimental measurements using FTIR (Fourier Transform Infrared) and UV absorption spectroscopy for CFx and SiFx neutral radicals, QMS (quadrupole mass spectrometry) for the ions, and Langmuir probe measurements of electron number density and temperature in an ICP GEC reference cell.

Hash, D. B.↗
DOE OSTI2024

Complex Structure of Molten FLiBe (2 Li F – Be F 2 ) Examined by Experimental Neutron Scattering, X-Ray Scattering, and Deep-Neural-Network Based Molecular Dynamics

The use of molten salts as coolants, fuels, and tritium breeding blankets in the next generation of fission and fusion nuclear reactors benefits from furthering the characterization of the molecular structure of molten halide salts, paving the way to predictive capability of the chemical and thermophysical properties of molten salts. Due to its neutronic, chemical, and thermochemical properties, 2 Li F - Be F 2 is a candidate molten salt for several fusion- and fission-reactor designs. We performed neutron and x-ray total-scattering measurements to determine the atomic structure of liquid 2 Li F - Be F 2 . We also performed and neural-network molecular-dynamics simulations to predict the structure obtained by neutron- and x-ray-diffraction experiments. The use of machine learning provides improvements to the efficiency in predicting the structure at a longer length scales than is achievable with simulations at significantly lower computational expense while retaining near accuracy. We found that the NNMD simulations accurately predicted the Be F 4 2 − oligomer formations seen in the experimental first-structure-factor peak. Our combination of high-resolution measurements with large-scale molecular dynamics provided an avenue to explore and experimentally verify the intermediate-range ordering beyond the first-nearest neighbor that has posed too many experimental and computational challenges in previous works. With a deeper understanding of the salt structure and ion ordering, the evolution of salt chemistry over the lifetime of a reactor can be better predicted, which is crucial to the licensing and operation of advanced fission and fusion reactors that employ molten salts. To this end, this work will serve as a reference for future studies of salt structure and macroscopic properties with and without the addition of solutes. Published by the American Physical Society 2024

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗