Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diffusion rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Ultrapure materials - Containerless evaporation and the roles of diffusion and Marangoni convection

Contamination from containers is a major problem in preparing ultrapure refractory materials. Space with its zero gravity and its high vacuum offers an opportunity for containerless purification of these materials. The evaporation of impurities from a melt will involve many complex chemical equilibria. Thermodynamic calculations have been modified to describe these equilibria when impurities in the melt evaporate into vacuum. The contributions of diffusion and Marangoni convection to mass transfer rates in the bulk liquid have been estimated. Calculations for the evaporative purification of molten alumina are given.

Dragoo, A. L.↗

The atmospheres of Titan and the Galilean satellites

The stability of various atmospheres on Titan and the Galilean satellites is examined relative to escape. One method consists of the comparison of exospheric temperature and a blow-off temperature defined for the various constituents. Another method consists of the evaluation of outflow based on a polytropic model. Hydrogen, methane, nitrogen, and neon atmospheres are examined. It is found that the Jovian satellites require heavier gases if they are to have any but very tenuous atmospheres, since all constituents examined are unstable. Nitrogen is stable on Titan, but methane and neon are marginally stable. Hydrogen is extremely unstable as a major constituent. As a minor constituent it is rapidly lost from Titan's thermosphere and must be replenished by outgassing or dissociation of a hydrogen compound, if the presently observed hydrogen content on Titan is not a transient occurrence. The rate of loss may be limited by diffusion, but could be augmented by vertical convection.

Gross, S. H.↗

Solidification (crystal growth) in the presence of gravitational forces

The surface tension behavior of doped and undoped InSb melts was investigated as well as their temperature and composition dependence. Surface tension in InSb melts was determined using the sessile-drop technique covering the temperature range from 530 C to 880 C. A linear regression of the data obtained shows that the temperature dependence of sigma is 392- (T-530) x (7000) plus or minus 10 dyne/cm. The d sigma/d Tau for intrinsics InSb is less than that previously reported. On the basis of the surface tension data obtained, it is concluded that surface tension induced convective flow velocities in InSb under reduced gravity conditions range from zero to at most 1 cm/sec. Accordingly, no interference with dopant segregation can be expected during growth in space because the momentum boundary layer (at the crystal melt interface) associated with any Marangoni-type convective flows would, at the given growth rate, be significantly larger than the predicted diffusion boundary layer thickness.

Gatos, H. C.↗

Proton-induced noise in digicons

The Space Telescope, which carries four Digicons, will pass several times per day through a low-altitude portion of the radiation belt called the South Atlantic Anomaly. This is expected to create interference in what is otherwise anticipated to be a noise-free device. Two essential components of the Digicon, the semiconductor diode array and the UV transmitting window, generate noise when subjected to medium-energy proton radiation, a primary component of the belt. These trapped protons, having energies ranging from 2 to 400 Mev and fluences at the Digicon up to 4,000 P+/sec-sq cm, pass through both the window and the diode array, depositing energy in each. In order to evaluate the effect of these protons, engineering test models of Digicon tubes to be flown on the High Resolution Spectrograph were irradiated with low-flux monoenergetic proton beams at the University of Maryland cyclotron. Electron-hole pairs produced by the protons passing through the diodes or the surrounding bulk caused a background count rate. This is the result of holes diffusing over a distance of many diode spacings, causing counts to be triggered simultaneously in the output circuits of several adjacent diodes. Pulse-height spectra of these proton-induced counts indicate that most of the bulk-related counts overlap the single photoelectron peak. A geometrical model will be presented of the charge collection characteristics of the diode array that accounts for most of the observed effects.

Smith, L. C.↗

On the tearing mode in quasi-neutral sheets

The paper examines the stability of the tearing mode in a quasi-neutral sheet which contains electron pitch angle scattering wave turbulence (or collisions). It is found that the pitch angle scattering dissipation destabilizes the tearing mode and that the tearing growth rate is proportional to the pitch angle diffusion coefficient. The results are discussed with reference to theories of the plasma sheet.

Coroniti, F. V.↗

Eddy diffusion coefficient for the atmosphere of Venus from radio scintillation measurements

Estimates are obtained of the vertical mass eddy diffusion coefficient of the Venus atmosphere in the region of turbulence near 60 km on the basis of radio scintillations observed during radio occultation by the atmosphere. The structure constant estimated from Pioneer Venus orbit 18 entrance radio occultation measurements is used, under the assumption that the turbulence is generated by wind-shear, to derive a value of 40,000 sq cm/sec for the vertical mass eddy diffusion coefficient, together with an energy dissipation rate of 20 sq cm/sec and a temperature fluctuation dissipation rate of 0.001 K-squared/sec. Results are noted to fall within the range measured for the earth's troposphere, however, indicate that small-scale turbulence is probably the dominant mechanism for vertical transport near the tropopause in the Venus atmosphere.

Woo, R.↗

Modelling of photodegradation in solar cell modules of substrate and superstrate design made with ethylene-vinyl acetate as pottant material

A computer model which simulates, in principle, the chemical changes in the photooxidation of hydrocarbons using as input data a set of elementary reactions, corresponding kinetic rate data and appropriate initial conditions was developed. The Model was refined and exploited to examine more closely the photooxidation and photostabilization of a hydrocarbon polymer. The results lead to the following observations. (1) The time to failure, tau sub f (chosen as the level of 5% C-H bond oxidation which is within the range anticipated for marked change in mechanical properties) varies as the inverse square root of the light intensity. However, tau sub f is almost unaffected by both the photoinitiator type and concentration. (2) The time to failure decreases with the rate of abstraction of C-H by peroxy radicals but increases with the rate of bimolecular radical termination controlled by diffusion. (3) Of the various stabilization mechanisms considered, the trapping of peroxy radicals is distinctly the most effective, although the concommitant decomposition of hydroperoxide is also desirable.

Somersall, A. C.↗

The effects of stimulated star formation on the evolution of the galaxy. III - The chemical evolution of nonlinear systems

The evolution of models for star formation in galaxies with disk and halo components is discussed. Two phases for the halo (gas and stars) and three for the disk (including clouds) are used in these calculations. The star-formation history is followed using nonlinear phase-coupling models which completely determine the populations of the phases as a function of time. It is shown that for a wide range of parameters, including the effects of both spontaneous and stimulated star formation and mass exchange between the spatial components of the system, the observed chemical history of the galaxy can easily be obtained. The most sensitive parameter in the detailed metallicity and star-formation history for the system is the rate of return of gas to the diffuse phase upon stellar death.

Shore, Steven N.↗

Theory of Influence of a Low-Volatility, Soluble Impurity on Spherically-Symmetric Combustion of Fuel Droplets

Analyses are given for the evolution of liquid-phase mass fraction profiles and temperature during combustion of fuel droplets composed of binary miscible mixtures of low-volatility and high-volatility constituents, with small initial mass fractions of the low-volatility material, or slow introduction of low-volatility material into the liquid phase by absorption from the gas phase. The gas phase is assumed to remain quasi-steady and the liquid temperature spatially uniform. The ratio of the liquid-phase diffusion coefficient to the initial burning-rate constant is treated as a small parameter. Asymptotic analyses in this parameter are developed, and the conservation equations are integrated numerically in obtaining descriptions of the combustion history. It is shown that at the surface of the droplet a boundary layer arises in which the mass fraction of the low-volatility component increases with time. The results are used to explain qualitatively some observed conditions of flame contraction and liquid disruption in droplet combustion.

Shaw, B. D.↗

Membrane Bioreactor With Pressure Cycle

Improved class of multilayer membrane bioreactors uses convention forced by differences in pressure to overcome some of diffusional limitations of prior bioreactors. In reactor of new class, flow of nutrient solution reduces adverse gradients of concentration, keeps cells supplied with fresh nutrient, and sweeps away products faster than diffusion alone. As result, overall yield and rate of reaction increased. Pressures in sweeping gas and nutrient alternated to force nutrient liquid into and out of biocatalyst layer through hyrophilic membrane.

Efthymiou, George S.↗

Reliability of degrading dynamic systems subject to dynamic random loads

Reliability was determined for two degrading dynamic systems subject to random load processes. Damage is caused by loss of components for Daniels systems and crack extension for plates with cracks. The analysis accounted for the coupling between response and current damage state of the system. It is based on mean crossing rates of conditional processes and properties of diffusion models. Simple systems are used to illustrate proposed methods for estimating reliability.

Grigoriu, Mircea↗

Interactions between flames on parallel solid surfaces

The interactions between flames spreading over parallel solid sheets of paper are being studied in normal gravity and in microgravity. This geometry is of practical importance since in most heterogeneous combustion systems, the condensed phase is non-continuous and spatially distributed. This spatial distribution can strongly affect burning and/or spread rate. This is due to radiant and diffusive interactions between the surface and the flames above the surfaces. Tests were conducted over a variety of pressures and separation distances to expose the influence of the parallel sheets on oxidizer transport and on radiative feedback.

Urban, David L.↗

Mass Flux of ZnSe by Physical Vapor Transport

Mass fluxes of ZnSe by physical vapor transport (PVT) were measured in the temperature range of 1050 to 1160 C using an in-situ dynamic technique. The starting materials were either baked out or distilled under vacuum to obtain near-congruently subliming compositions. Using an optical absorption technique Zn and Se, were found to be the dominant vapor species. Partial pressures of Zn and Se, over the starting materials at temperatures between 960 and 1140 C were obtained by measuring the optical densities of the vapor phase at the wavelengths of 2138, 3405, 3508, 3613, and 3792 A. The amount and composition of the residual gas inside the experimental ampoules were measured after the run using a total pressure gauge. For the first time, the experimentally determined partial pressures of Zn and Se, and the amount and composition of the residual gas were used in a one-dimensional diffusion limited analysis of the mass transport rates for a PVT system. Reasonable agreement between the experimental and theoretical results was observed.

Sha, Yi-Gao↗

Investigation of Sooting in Microgravity Droplet Combustion: Fuel-Dependent Effects

Kumagai and coworkers first performed microgravity droplet combustion experiments [Kumagai, 1957]. The primary goal of these early experiments were to validate simple 'd(sup 2)-law models [Spalding, 1954, Godsave, 1954] Inherent in the 'd(sup 2) -law' formulation and in the scope of the experimental observation is the neglect of sooting behavior. In fact, the influence of sooting has not received much attention until more recent works [Choi et al., 1990; Jackson et al., 1991; Jackson and Avedisian, 1994; Choi and Lee, 1996; Jackson and Avedisian, 1996; Lee et al., 1998]:. Choi and Lee measured soot volume fraction for microgravity droplet flames using full-field light extinction and subsequent tomographic inversion [Choi and Lee, 1996]. In this investigation, soot concentrations were measured for heptane droplets and it was reported that soot concentrations were considerably higher in microgravity compared to the normal gravity flame. It was reasoned that the absence of buoyancy and the effects of thermophoresis resulted in the higher soot concentrations. Lee et al. [1998] performed soot measurement experiments by varying the initial droplet diameter and found marked influence of sooting on the droplet burning behavior. There is growing sentiment that sooting in droplet combustion must no longer be neglected and that "perhaps one of the most important outstanding contributions of (micro)g droplet combustion is the observation that in the absence of asymmetrical forced and natural convection, a soot shell is formed between the droplet surface and the flame, exerting an influence on the droplet combustion response far greater than previously recognized." [Law and Faeth, 1994]. One of the methods that we are exploring to control the degree of sooting in microgravity is to use different fuels. The effect of fuel structure on sooting propensity has been investigated for over-ventilated concentric coflowing buoyant diffusion flames. (Glassman, 1996]. In these investigations, the fuel flowrate was increased until smoke was observed to escape from the "luminous visible flame" [Glassman, 1996]. A total of 29 fuels were used in order to characterize relative sooting propensity. The sooting propensity of a particular fuel was assessed by comparing the flowrates for soot emission from the tip of the flame. It was reported that the sooting tendency for diffusion flames increased for fuels with higher rates of pyrolysis. Randolph and Law [1986 and not 1994] also examined the effect of fuel structure on droplet sooting behavior. In their experiments the droplets were separated from the bulk gas stream and quenched with nitrogen prior to gravimetric measurements. A variety of fuels were studied, namely aromatics, phenyl-alkanes and alkanes. The results were in qualitative agreement with the work of Glassman [1986]. Vander Wal et al. [1994] performed relative soot concentration measurements using laser-induced incandescence for heptane and decane fuel droplets burning under normal-gravity conditions. It was found that soot volume fractions for decane was more than a factor of two larger than that for heptane. Although the normal-gravity investigations have provided some important insights regarding the influence of fuel structure on the sooting behavior of droplet flames, results cannot be easily extrapolated for microgravity studies since increased residence times and thermophoretic effects must be considered in greater detail. Several studies have compared sooting behavior of different fuel droplets burning under microgravity conditions [Card and Choi, 1990; Jackson et al., 1991; Jackson and Avedisian, 1994], however, detailed quantitative results were not provided. In all of these previous studies, the degree of sooting was only visually assessed from an incandescent backlighted image of the soot containing region. Such techniques can provide misleading results regarding sooting behavior [Choi, 1996].

Manzello, Samuel L.↗

X-ray Spectra and Pulse Frequency Changes in SAX J2103.5+4545

The November 1999 outburst of the transient pulsar SAX J2103.5+4545 was monitored with the large area detectors of the Rossi X-Ray Timing Explorer until the pulsar faded after a year. The 358 s pulsar was spun up for 150 days, at which point the flux dropped quickly by a factor of approximately 7, the frequency saturated and, as the flux continued to decline, a weak spin-down began. The pulses remained strong during the decay and the spin-up/flux correlation can be fit to the Ghosh and Lamb derivations for the spin-up caused by accretion from a thin, pressure-dominated disk, for a distance approximately 3.2 kpc and a surface magnetic field approximately 1.2 x 10(exp 13) Gauss. During the bright spin-up part of the outburst, the flux was subject to strong orbital modulation, peaking approximately 3 days after periastron of the eccentric 12.68 day orbit, while during the faint part, there was little orbital modulation. The X-ray spectra were typical of accreting pulsars, describable by a cut-off power-law, with an emission line near the 6.4 keV of Kappa(sub alpha) fluorescence from cool iron. The equivalent width of this emission did not share the orbital modulation, but nearly doubled during the faint phase, despite little change in the column density. The outburst could have been caused by an episode of increased wind from a Be star, such that a small accretion disk is formed during each periastron passage. A change in the wind and disk structure apparently occurred after 5 months such that the accretion rate was no longer modulated or the diffusion time was longer. The distance estimate implies the X-ray luminosity observed was between 1 X 10(exp 36) ergs s(exp -1) and 6 x 10(exp 34) ergs s(exp -1), with a small but definite correlation of the intrinsic power-law spectral index.

Baykal, A.↗

Megawatt Electromagnetic Plasma Propulsion

The NASA Glenn Research Center program in megawatt level electric propulsion is centered on electromagnetic acceleration of quasi-neutral plasmas. Specific concepts currently being examined are the Magnetoplasmadynamic (MPD) thruster and the Pulsed Inductive Thruster (PIT). In the case of the MPD thruster, a multifaceted approach of experiments, computational modeling, and systems-level models of self field MPD thrusters is underway. The MPD thruster experimental research consists of a 1-10 MWe, 2 ms pulse-forming-network, a vacuum chamber with two 32 diffusion pumps, and voltage, current, mass flow rate, and thrust stand diagnostics. Current focus is on obtaining repeatable thrust measurements of a Princeton Benchmark type self field thruster operating at 0.5-1 gls of argon. Operation with hydrogen is the ultimate goal to realize the increased efficiency anticipated using the lighter gas. Computational modeling is done using the MACH2 MHD code, which can include real gas effects for propellants of interest to MPD operation. The MACH2 code has been benchmarked against other MPD thruster data, and has been used to create a point design for a 3000 second specific impulse (Isp) MPD thruster. This design is awaiting testing in the experimental facility. For the PIT, a computational investigation using MACH2 has been initiated, with experiments awaiting further funding. Although the calculated results have been found to be sensitive to the initial ionization assumptions, recent results have agreed well with experimental data. Finally, a systems level self-field MPD thruster model has been developed that allows for a mission planner or system designer to input Isp and power level into the model equations and obtain values for efficiency, mass flow rate, and input current and voltage. This model emphasizes algebraic simplicity to allow its incorporation into larger trajectory or system optimization codes. The systems level approach will be extended to the pulsed inductive thruster and other electrodeless thrusters at a future date.

Gilland, James↗

Quantitative Relationships between Photosynthetic, Nitrogen Fixing, and Fermentative H2 Metabolism in a Photosynthetic Microbial Mat

The ultimate potential of any microbial ecosystem to contribute chemically to its environment - and therefore, to impact planetary biogeochemistry or to generate recognizable biosignatures - depends not only on the individual metabolic capabilities of constituent organisms, but also on how those capabilities are expressed through interactions with neighboring organisms. This is particularly important for microbial mats, which compress an extremely broad range of metabolic potential into a small and dynamic system. H2 participates in many of these metabolic processes, including the major elemental cycling processes of photosynthesis, nitrogen fixation, sulfate reduction, and fermentation, and may therefore serve as a mediator of microbial interactions within the mat system. Collectively, the requirements of energy, electron transfer, and biomass element stoichiometry suggest quantitative relationships among the major element cycling processes, as regards H2 metabolism We determined experimentally the major contributions to 32 cycling in hypersaline microbial mats from Baja California, Mexico, and compared them to predicted relationships. Fermentation under dark, anoxic conditions is quantitatively the most important mechanism of H2 production, consistent with expectations for non-heterocystous mats such as those under study. Up to 16% of reducing equivalents fixed by photosynthesis during the day may be released by this mechanism. The direct contribution of nitrogen fixation to H2 production is small in comparison, but this process may indirectly stimulate substantial H2 generation, by requiring higher rates of fermentation. Sulfate reduction, aerobic consumption, diffusive and ebulitive loss, and possibly H2-based photoreduction of CO2 serve as the principal H2 sinks. Collectively, these processes interact to create an orders-of-magnitude daily variation in H2 concentrations and fluxes, and thereby in the oxidation-reduction potential that is imposed on microbial processes occuring within the mat matrix.

Hoehler, Tori M.↗

Ring Current Dynamic in the Presence of EMIC Waves

The effect of EMIC waves, generated by a positive ion temperature anisotropy on Earth s RC ions is one of the best known examples of wave-particle interaction in the magnetosphere and the most controversial mechanism of RC losses. Under certain conditions, relativistic electrons with energy 21 MeV can be removed from the outer RB by EMIC wave scattering during a magnetic storm much faster than by any other loss mechanisms. That is why the calculation of EMIC waves is a very critical part of the NASA LWS program. The new RC model that we have developed and present for the first time has several new features that we have combine together in a one single model: (a) several lower frequency cold plasma wave modes are taken into account; (b) wave tracing of these wave has been incorporated in the energy EMIC wave equation; (c) no assumptions regarding wave shape spectra have been made; (d) no assumptions regarding the shape of particle distribution have been made to calculate the growth rate; (e) pitch- angle, energy, and mix diffusions are taken into account together for the first time; (f) the exact loss-cone RC analytical solution has been found and coupled with bounce-averaged numerical solution of kinetic equation; (g) LHW are included as an additional factor that contributes to saturation process of EMIC waves; and (h) the hot ions were included in the real part of dielectric permittivity tensor. We compare our theoretical results with the different EMIC waves models as well as RC experimental data.

Khazanov, G. V.↗