Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Conditional distributions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Ice Caps and Ice Belts: The Effects of Obliquity on Ice−Albedo Feedback

Planetary obliquity determines the meridional distribution of the annual mean insolation. For obliquity exceeding 55°, the weakest insolation occurs at the equator. Stable partial snow and ice cover on such a planet would be in the form of a belt about the equator rather than polar caps. An analytical model of planetary climate is used to investigate the stability of ice caps and ice belts over the widest possible range of parameters. The model is a non-dimensional diffusive Energy Balance Model, representing insolation, heat transport, and ice−albedo feedback on a spherical planet. A complete analytical solution for any obliquity is given and validated against numerical solutions of a seasonal model in the “deep-water” regime of weak seasonal ice line migration. Multiple equilibria and unstable transitions between climate states (ice-free, Snowball, or ice cap/belt) are found over wide swaths of parameter space, including a “Large Ice-Belt Instability” and “Small Ice-Belt Instability” at high obliquity. The Snowball catastrophe is avoided at weak radiative forcing in two different scenarios: weak albedo feedback and inefficient heat transport (favoring stable partial ice cover), or efficient transport at high obliquity (favoring ice-free conditions). From speculative assumptions about distributions of planetary parameters, three-fourths to four-fifths of all planets with stable partial ice cover should be in the form of Earth-like polar caps.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1979

Experimental shock metamorphism of mono- and polycrystalline olivine - A comparative study

The paper reports on a series of controlled shock recovery experiments which have been performed on over 40 samples including monocrystalline, polycrystalline, dunite, and porous particulate olivine-bearing targets. Results of the mineralogical and petrological analyses of these samples are used to establish a general and comparative diagnosis of shock effects generated in various olivine-bearing materials. Finally, some experiments are conducted under different ambient pO2 conditions so that information on the distribution of observed impact features is derived as a function not only of peak pressure and texture of the target sample, but also of specific environmental conditions.

Bauer, J. F.↗
NASA NTRS1994

Testing the gravitational instability hypothesis?

We challenge a widely accepted assumption of observational cosmology: that successful reconstruction of observed galaxy density fields from measured galaxy velocity fields (or vice versa), using the methods of gravitational instability theory, implies that the observed large-scale structures and large-scale flows were produced by the action of gravity. This assumption is false, in that there exist nongravitational theories that pass the reconstruction tests and gravitational theories with certain forms of biased galaxy formation that fail them. Gravitational instability theory predicts specific correlations between large-scale velocity and mass density fields, but the same correlations arise in any model where (a) structures in the galaxy distribution grow from homogeneous initial conditions in a way that satisfies the continuity equation, and (b) the present-day velocity field is irrotational and proportional to the time-averaged velocity field. We demonstrate these assertions using analytical arguments and N-body simulations. If large-scale structure is formed by gravitational instability, then the ratio of the galaxy density contrast to the divergence of the velocity field yields an estimate of the density parameter Omega (or, more generally, an estimate of beta identically equal to Omega(exp 0.6)/b, where b is an assumed constant of proportionality between galaxy and mass density fluctuations. In nongravitational scenarios, the values of Omega or beta estimated in this way may fail to represent the true cosmological values. However, even if nongravitational forces initiate and shape the growth of structure, gravitationally induced accelerations can dominate the velocity field at late times, long after the action of any nongravitational impulses. The estimated beta approaches the true value in such cases, and in our numerical simulations the estimated beta values are reasonably accurate for both gravitational and nongravitational models. Reconstruction tests that show correlations between galaxy density and velocity fields can rule out some physically interesting models of large-scale structure. In particular, successful reconstructions constrain the nature of any bias between the galaxy and mass distributions, since processes that modulate the efficiency of galaxy formation on large scales in a way that violates the continuity equation also produce a mismatch between the observed galaxy density and the density inferred from the peculiar velocity field. We obtain successful reconstructions for a gravitational model with peaks biasing, but we also show examples of gravitational and nongravitational models that fail reconstruction tests because of more complicated modulations of galaxy formation.

Babul, Arif↗
NASA NTRS1974

High latitude ionospheric winds related to solar-interplanetary conditions

Two recent results imply that the distribution of winds in the polar ionosphere should change as a function of the direction of the interplanetary magnetic field. From the motions of chemically released ion and neutral clouds, it is apparent that neutral winds in the high latitude ionosphere are driven principally by ion drag forces. OGO-6 electric field measurements have demonstrated that there are definite relationships between the time latitude distribution of ionospheric plasma convection and interplanetary magnetic field parameters, and also that the distribution is most sensitive to the azimuthal angle of the interplanetary field. The lower altitude, meteorological effects of these externally driven ionospheric winds are not known. However, observations of infrasonic waves following sudden ionization enhancements indicate the existence of momentum transfer.

Heppner, J. P.↗
DOE OSTI2025

Intrinsic Kinetics of Polyethylene Terephthalate Pyrolysis via Micropyrolysis and Multivariate Chromatographic Analysis

This study provides an in-depth investigation of the primary decomposition of polyethylene terephthalate (PET) via pyrolysis, employing an experimental-analytic workflow that integrates design of experiments (DoE), micropyrolysis coupled with comprehensive two-dimensional gas chromatography (GC×GC), and multivariate data analysis to verify intrinsic kinetic conditions and elucidate evolving product distributions for mapping key reaction pathways. Peaks that could not be identified using commercial spectral libraries were assigned using Mass Frontier simulations, enabling the identification of divinyl terephthalate, ethyl vinyl terephthalate, and 2-(benzoyloxy)ethyl vinyl terephthalate. A polar×polar (non-orthogonal) column set tailored for the detection of carboxylic acids enhanced the quantification of benzoic acid, 4-vinylbenzoic acid, 4-ethylbenzoic acid, and methylbenzoic acid by up to 6-fold relative to an orthogonal column combination (non-polar×mid-polar). Moreover, pyrolysis variables were systematically evaluated using a Box- Behnken design (BBD), encompassing pyrolysis temperature (500−600 °C), sample weight (50−150 μg), and carrier gas flow rate (100−300 mL min −1 ). Among these, pyrolysis temperature was the only statistically significant factor influencing product yields, ranging from 58.78 to 84.26 wt %. In contrast, neither the sample weight nor the carrier gas flow rate had a significant effect on product yields within the evaluated experimental space. At 600 °C, the major pyrolysis products were benzoic acid (up to 20.20 ± 1.46 wt %) and CO 2 (up to 21.28 ± 1.46 wt %), which can be produced through decarboxylation reactions. These findings underscore the critical importance of selecting appropriate analytical columns for the accurate quantification of heteroatomcontaining products such as carboxylic acids, which may otherwise be underestimated or undetected due to their reactivity with the stationary phase of non-polar and mid-polar columns, as well as other GC components. They also highlight the importance of selecting pyrolysis conditions for investigating the primary decomposition of PET under an isothermal kinetically limited regime.

aromatic compounds↗
DOE OSTI2025

Networked Microgrid Topology Reconfiguration to Promote Fairness in Proactive Load Shedding

Increasing occurrences of natural disasters and grid emergency events consistently challenge the safe and reliable operations of power systems. During such emergency situations, system operators may proactively shed load to mitigate risks. However, uncoordinated implementation of load shedding may disrupt electricity supply and even lead to cascading failures. Meanwhile, it is crucial to address potential biases affecting different customers when executing load shedding. This paper addresses the dynamic topology reconfiguration problem for networked microgrids with distributed energy resources under emergency conditions. Specifically, we propose a novel rolling-horizon optimization model that integrates fairness-aware constraints into the networked microgrid topology reconfiguration. Unlike existing approaches that focus solely on efficiency or apply fairness considerations in static settings, our method explicitly incorporates temporal fairness constraints to restrict repeated or excessive load curtailment for load blocks. Moreover, the fairness-aware constraints are specifically developed for the context of dynamic networked microgrid topology reconfiguration, and are designed to be convex or amenable to linear reformulations, which offers a more tractable alternative to traditional models with non-convex formulations. Numerical studies on a modified IEEE 13-bus system and a larger-sized SMART-DS networked microgrid system demonstrate the performance of the proposed algorithm towards more fairness-aware networked microgrid topology reconfiguration decision-making.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1983

Computation of viscous flows over airfoils, including separation, with a coupling approach

Viscous incompressible flows over single or multiple airfoils, with or without separation, were computed using an inviscid flow calculation, with modified boundary conditions, and by a method providing calculation and coupling for boundary layers and wakes, within conditions of strong viscous interaction. The inviscid flow is calculated with a method of singularities, the numerics of which were improved by using both source and vortex distributions over profiles, associated with regularity conditions for the fictitious flows inside of the airfoils. The viscous calculation estimates the difference between viscous flow and inviscid interacting flow, with a direct or inverse integral method, laminar or turbulent, with or without reverse flow. The numerical method for coupling determines iteratively the boundary conditions for the inviscid flow. For attached viscous layers regions, an underrelaxation is locally calculated to insure stability. For separated or separating regions, a special semi-inverse algorithm is used. Comparisons with experiments are presented.

Leballeur, J. C.↗
NASA NTRS1949

Application of Theodorsen's theory to propeller design

A theoretical analysis is presented for obtaining, by use of Theodorsen's propeller theory, the load distribution along a propeller radius to give the optimum propeller efficiency for any design condition. The efficiencies realized by designing for the optimum load distribution are given in graphs, and the optimum efficiency for any design condition may be read directly from the graph without any laborious calculations. Examples are included to illustrate the method of obtaining the optimum load distributions for both single-rotating and dual-rotating propellers.

Crigler, John L↗
NASA NTRS1974

Energy transfer in volume-reflecting heat shields

An approximate analysis of radiative transfer in highly scattering materials was developed based on the Kubelka-Munk differential equations--a set of two differential equations representing the spatial rate of change of radiative half-fluxes within the scattering media. These approximate solutions of the Kubelka-Munk equations together with analytic solutions for the steady state temperature distribution for two types of boundary conditions are given. These solutions show the influence of back surface reflectance, scattering power, incident radiative flux parameter and boundary conductive flux parameter on overall reflectance and temperature distributions. This radiation field analysis, adapted to spherical geometry, was applied to the evaluation of the thermal performance of teflon and fritted quartz as heat protection materials for entry into the atmosphere of Jupiter.

Weston, K. C.↗
NASA NTRS1994

Perpendicular electron heating by absorption of auroral kilometric radiation

We investigate the possibility of perpendicular heating of electrons and the generation of '90 deg -electron conics' by particle diffusion in velocity space due to wave-particle interaction with intense auroral kilometric radiation. This interaction is made possible by the downward shift in the R-X cutoff below the electron cyclotron frequency that occurs in the presence of warm plasma. We stimulate this condition and solve the diffusion equation using a finite difference algorithm. The results show strong perpendicular electron heating and indicate that the main characteristics of an electron conic distribution can be reproduced under these conditions.

Morgan, D. D.↗
DOE OSTI2022

Dynamics of deuterium retention and desorption from plasma-facing materials in fusion reactor-relevant conditions

Hydrogen isotopes retention and desorption during and after discharges in fusion devices are still not well understood due to the complex device conditions and limitations of in-situ diagnostics and measurements. Here, we simulated well-diagnosed recent experiments at the DIII-D facility to benchmark our ITMC-DYN integrated package of modeling deuterium diffusion, retention, and desorption during and after D discharge irradiation. Modeling results were compared with detail experimental data of D desorption fluxes for various irradiation conditions. We predicted the temporal evolution of free and trapped D distribution in tungsten (W) plasma-facing material (PFM). Effects of key parameters namely diffusion coefficient, recombination rate, trapping energies against different defect types, were examined in these simulations. Existing experimental data of these parameters in literature varies significantly which makes it harder to identify key mechanisms and physics responsible for hydrogen isotope retention and desorption. The purpose of this work is to accurately simulate recent well-diagnosed reactor experiments given the uncertainties in such parameters and identify mechanisms responsible for the retention and desorption. We implemented the best identified diffusion, recombination, and trapping parameters in ITMC-DYN package that integrate both various collisional and thermal processes. We predicted, for example, that sample cooling between discharges in DIII-D operations can significantly affect the spatial distribution of trapped D in W under reactor irradiation conditions. Correct prediction of desorption spectra from samples irradiated during 10 DIII-D discharges showed that up to 35% of D can be retained in high binding energy defects such as vacancy clusters or voids.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1996

Computational Methods for Frictional Contact With Applications to the Space Shuttle Orbiter Nose-Gear Tire

A computational procedure is presented for the solution of frictional contact problems for aircraft tires. A Space Shuttle nose-gear tire is modeled using a two-dimensional laminated anisotropic shell theory which includes the effects of variations in material and geometric parameters, transverse-shear deformation, and geometric nonlinearities. Contact conditions are incorporated into the formulation by using a perturbed Lagrangian approach with the fundamental unknowns consisting of the stress resultants, the generalized displacements, and the Lagrange multipliers associated with both contact and friction conditions. The contact-friction algorithm is based on a modified Coulomb friction law. A modified two-field, mixed-variational principle is used to obtain elemental arrays. This modification consists of augmenting the functional of that principle by two terms: the Lagrange multiplier vector associated with normal and tangential node contact-load intensities and a regularization term that is quadratic in the Lagrange multiplier vector. These capabilities and computational features are incorporated into an in-house computer code. Experimental measurements were taken to define the response of the Space Shuttle nose-gear tire to inflation-pressure loads and to inflation-pressure loads combined with normal static loads against a rigid flat plate. These experimental results describe the meridional growth of the tire cross section caused by inflation loading, the static load-deflection characteristics of the tire, the geometry of the tire footprint under static loading conditions, and the normal and tangential load-intensity distributions in the tire footprint for the various static vertical loading conditions. Numerical results were obtained for the Space Shuttle nose-gear tire subjected to inflation pressure loads and combined inflation pressure and contact loads against a rigid flat plate. The experimental measurements and the numerical results are compared.

Tanner, John A.↗
DOE OSTI2017

Evaluating the Performance Envelope of Axial Flow HEPA Filter Designs - 17466

Nuclear grade high efficiency particulate air (HEPA) filters are routinely employed as the final control element in confinement ventilation systems. Approximately 6000 nuclear grade HEPA filters are purchased each year for use in the Department of Energy National Nuclear Security Administration (DOE/NNSA) complex. The traditional HEPA filter utilizes a pleated filter medium of fibrous glass that has been produced in a manner analogous to manufacturing paper. Containment ventilation systems are designed to condition the air-stream (temperature, relative humidity, moisture, particle size distribution of aerosols, and aerosol concentration) to levels and conditions that fibrous glass HEPA filters can handle. Axial Flow filters can be purchased with physical separators or embossed medium to maintain proper pleat geometry. Separator-less designs use media embossed with a corrugation pattern to retain pleat geometry. At least some versions of the separator-less filter packs have demonstrated unexpected and rapid failure under slightly elevated temperature and humidity conditions. The effects of age on HEPA filter performance have been a concern for at least two decades. A combination of physical evaluation of aged filter media and a review of filter failure records resulted in Appendix C of the Nuclear Air Cleaning Handbook (NACH), Determination of HEPA Filter Life. Mississippi State University is conducting studies to more clearly identify the operating envelope of separator and separator-less designs of ASME AG-1 Section FC axial flow HEPA filters under a set of generic design basis conditions. A parallel study is also being conducted to evaluate the effects of age on fibrous glass HEPA filters. Activities described in this paper have been conducted under Institute for Clean Energy Technology (ICET's) NQA-1 nuclear quality assurance program approved by DOE-EM. Testing meets the requirements of EM Quality Assurance Program (QAP) EM-QA-001, Rev. 1, June 11, 2012 that includes the applicable requirements of NQA-1-2008/2009a and DOE Order 414.1D. (authors)

07 ISOTOPE AND RADIATION SOURCES↗
NASA NTRS1974

Use of potential flow theory to evaluate subsonic inlet data from a simulator-powered nacelle at cruise conditions

Incompressible potential flow theory corrected for compressibility effects, using the Lieblein-Stockman compressibility correction, was used to predict surface and flow field static pressures for a subsonic inlet at cruise conditions. The calculated internal and external surface static pressures were in good agreement with data at most conditions. The analysis was used to determine the capture stream-tube location and static-pressure distribution. Additive drag coefficients obtained from these results were consistently higher than those obtained using one-dimensional compressible flow theory. Increasing the distance between the inlet and boattail increased the cowl drag force. The effect of the boundary layer on internal and external surface static-pressure distributions was small at the design cruise condition. The analytical results may be used as an aid to data reduction and for predicting inlet mass flow, stagnation point location, and inlet additive drag.

Bober, L. J.↗
NASA NTRS1982

Comparison of transport equations based on Maxwellian and bi-Maxwellian distributions for anisotropic plasmas

A wide variety of plasma flow conditions is found in aeronomy and space plasma physics. Transport equations based on an isotropic Maxwellian vilecity distribution function can be used to describe plasma flows which contain 'small' temperature anisotropies. However, for plasma flows characterized by large temperature anisotropies, transport equations based on an anisotropic bi-Maxwellian (or two-temperature) velocity distribution function are expected to provide a much better description of the plasma transport properties. The present investigation is concerned with the extent to which transport equations based on both Maxwellian and bi-Maxwellian series expansions can describe plasma flows characterized by non-Maxwellian velocity distributions, giving particular attention to a modelling of the anisotropic character of the distribution function. The obtained results should provide clues as to the extent to which a given series expansion can account for the anisotropic character of a plasma.

Barakat, A. R.↗
NASA NTRS2006

Phased-Array Study of Dual-Flow Jet Noise: Effect of Nozzles and Mixers

A 16-microphone linear phased-array installed parallel to the jet axis and a 32-microphone azimuthal phased-array installed in the nozzle exit plane have been applied to identify the noise source distributions of nozzle exhaust systems with various internal mixers (lobed and axisymmetric) and nozzles (three different lengths). Measurements of velocity were also obtained using cross-stream stereo particle image velocimetry (PIV). Among the three nozzle lengths tested, the medium length nozzle was the quietest for all mixers at high frequency on the highest speed flow condition. Large differences in source strength distributions between nozzles and mixers occurred at or near the nozzle exit for this flow condition. The beamforming analyses from the azimuthal array for the 12-lobed mixer on the highest flow condition showed that the core flow and the lobe area were strong noise sources for the long and short nozzles. The 12 noisy spots associated with the lobe locations of the 12-lobed mixer with the long nozzle were very well detected for the frequencies 5 KHz and higher. Meanwhile, maps of the source strength of the axisymmetric splitter show that the outer shear layer was the most important noise source at most flow conditions. In general, there was a good correlation between the high turbulence regions from the PIV tests and the high noise source regions from the phased-array measurements.

Soo Lee, Sang↗