SEARCH · Engineering Papers

Results for “CONTACT RESISTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Sputtered W-N diffusion barriers

The thermal stability of reactively sputtered tungsten-nitrogen alloy thin films is investigated for the application as diffusion barriers in silicon contact metallizations. The composition of W-N barriers is varied over a wide range including pure W. Aluminum, gold, and silver are used as low resistivity overlayers. Metallurgical interactions at temperatures ranging from 500 to 900 C are studied. Incorporating nitrogen into tungsten advantageously stabilizes all three systems. The overall failure takes place rapidly above critical temperatures that depend on both the metal overlayer and the microstructure of the barrier. In some cases, W-N alloys can effectively prevent interdiffusion at temperatures as high as 800 C for 30 min.

Kattelus, H. P.↗

NASA NTRS1986

Investigation of high efficiency silicon MINP solar cells

This paper includes results of both theoretical and experimental studies of silicon metal insulator n/p cells. Performance calculations are described which give expected efficiencies as a function of base resistivity. Fabrication and characterization of cells are discussed, and detailed analyses of current loss mechanisms are presented. Using 0.2-ohm cm FZ material and Mg tunneling contacts, AM 1 efficiencies in the range of 16.5-17 percent have been achieved.

Olsen, L. C.↗

NASA NTRS1989

The lubrication force between two viscous drops

The present determination of the hydrodynamic force resisting the relative motion of two unequal drops moving in Stokes flow conditions along their line of centers assumes that the drops are in near-contact, and possess sufficiently high interfacial tension to remain spherical. Depending on the ratio of drop viscosity to that of the continuous phase, as well as on the ratio of the distance between drops to their reduced radius, three possible flow situations arise: these correspond to nearly-rigid drops, drops with partially mobile interfaces, and drops with fully mobile interfaces.

Davis, Robert H.↗

NASA NTRS1992

SiC device development for high temperature sensor applications

Progress made in the processing and characterization of 3C-SiC for high temperature sensor applications is reviewed. Piezoresistance properties of silicon carbide and the temperature coefficient of resistivity of n-type beta-SiC are presented. In addition, photoelectrical etching and dopant selective etch-stops in SiC and high temperature Ohmic contacts for n-type beta-SiC sensors are discussed.

Shor, J. S.↗

NASA NTRS1995

Single crystal silicon filaments fabricated in SOI: A potential IR source for a microfabricated photometric CO2 sensor

The objective of this project was to design, fabricate, and test single crystal silicon filaments as potential black body IR sources for a spectrophotometric CO2 sensing microsystem. The design and fabrication of the silicon-on-insulator (SOI) filaments are summarized and figures showing the composite layout of the filament die (which contains four filaments of different lengths -- 500 microns, 1 mm, 1.5 mm and 2 mm -- and equal widths of 15 microns) are presented. The composite includes four mask layers: (1) silicon - defines the filament dimensions and contact pads; (2) release pit - defines the oxide removed from under the filament and hence, the length of the released filament; (3) Pyrex pit - defines the pit etched in the Pyrex cap (not used); and (4) metal - defines a metal pattern on the contact pads or used as a contact hole etch. I/V characteristics testing of the fabricated SOI filaments is described along with the nitride-coating procedures carried out to prevent oxidation and resistance instability.

Tu, Juliana↗

NASA NTRS2005

Carbon nanotube Schottky diodes using Ti-Schottky and Pt-ohmic contacts for high frequency applications

We have demonstrated Schottky diodes using semiconducting single-walled nanotubes (s-SWNTs) with titanium Schottky and platinum Ohmic contacts for high-frequency applications. The diodes are fabricated using angled evaporation of dissimilar metal contacts over an s-SWNT. The devices demonstrate rectifying behavior with large reverse bias breakdown voltages of greater than 15 V. To decrease the series resistance, multiple SWNTs are grown in parallel in a single device, and the metallic tubes are burnt-out selectively. At low biases these diodes showed ideality factors in the range of 1.5 to 1.9. Modeling of these diodes as direct detectors at room temperature at 2.5 terahertz (THz) frequency indicates noise equivalent powers (NEP) potentially comparable to that of the state-of-the-art gallium arsenide solid-state Schottky diodes, in the range of 10-13 W(square root)xHz.

semiconducting↗

DOE OSTI2021

Valuation of Surface Coatings in High-Energy Density Lithium-ion Battery Cathode Materials

Artificial barriers, usually with either electrochemically active or inactive coating materials, are deployed on cathode material surfaces to mitigate detrimental side reactions by suppressing direct contact of cathode and electrolyte called surface coatings. These surface coatings are commonly known to increase the wettability of liquid electrolyte and reduce the interfacial charge transfer resistance. An important caveat is the selection of appropriate coating material with appropriate thickness for achieving enhanced electrochemical performance. As modern battery materials are increasingly developed with some type of surface coating, a careful and thorough examination of their role in mitigating the cycle life issues of cathode materials is paramount. Here, this comprehensive review article extensively covers the selection criteria of coating materials based on their chemical and physical properties and electrochemical functionalities. Additionally, the article discusses the concept of critical coating thickness and methods of achieving homogeneous coating architectures that deliver desired performance benefits. Furthermore, this comprehensive article summarizes the recent advancements, effectiveness, necessity of cathode surface coatings and identifies the key aspect of structure-property correlation between coating type/thickness and lithium-ion diffusion through coating layers as the linchpin that validates surface coating approaches especially for high capacity nickel-rich cathodes.

25 ENERGY STORAGE↗

NASA NTRS1974

Low-high junction theory applied to solar cells

Recent use of alloying techniques for rear contact formation has yielded a new kind of silicon solar cell, the back surface field (BSF) cell, with abnormally high open-circuit voltage and improved radiation resistance. Several analytical models for open-circuit voltage based on the reverse saturation current are formulated to explain these observations. The zero surface recombination velocity (SRV) case of the conventional cell model, the drift field model, and the low-high junction (LHJ) model can predict the experimental trends. The LHJ model applies the theory of the low-high junction and is considered to reflect a more realistic view of cell fabrication. This model can predict the experimental trends observed for BSF cells.

Godlewski, M. P.↗

NASA NTRS1978

Electroexplosive device

An electroexplosive device is presented which employs a header having contact pins hermetically sealed with glass passing through from a connector end of the header to a cavity filled with a shunt layer of a new nonlinear resistive composition and a heat-sink layer of a new dielectric composition having good thermal conductivity and capacity. The nonlinear resistive layer and the heat-sink layer are prepared from materials by mixing with a low temperature polymerizing resin. The resin is dissolved in a suitable solvent and later evaporated. The resultant solid composite is ground into a powder, press formed into the header and cured (polymerized) at about 250 to 300 F.

Menichelli, V. J.↗

NASA NTRS1982

Metal Sandwith Panel With Biaxially Corrugated Core

Biaxially-corrugated sandwich core, formed by concurrent diffusion bonding and superplastic deformation, makes a proposed sandwich panel unusually strong and stiff. New panel should be useful where light-weight panel that resists bending is needed. Panel would have internal core consisting of multitude of hollow, truncated pyramids. Four layers of panel would be diffusion-binded at all contacting areas.

Ko, W. L.↗

NASA NTRS1985

Split-cross-bridge resistor for testing for proper fabrication of integrated circuits

An electrical testing structure and method is described whereby a test structure is fabricated on a large scale integrated circuit wafer along with the circuit components and has a van der Pauw cross resistor in conjunction with a bridge resistor and a split bridge resistor, the latter having two channels each a line width wide, corresponding to the line width of the wafer circuit components, and with the two channels separated by a space equal to the line spacing of the wafer circuit components. The testing structure has associated voltage and current contact pads arranged in a two by four array for conveniently passing currents through the test structure and measuring voltages at appropriate points to calculate the sheet resistance, line width, line spacing, and line pitch of the circuit components on the wafer electrically.

Buehler, M. G.↗

NASA NTRS1994

Non-linear numerical analysis of the Iosipescu specimen for composite materials

A nonlinear elastic finite element analysis is presented of the Iosipescu shear specimen tested in the modified Wyoming fixture for unidirectional graphite/epoxy composites. It is shown that the nonlinear effects due to specimen-to-fixture contact interactions and specimen geometry on the overall shear response are negligible. It is proposed that the tangential shear modulus should be used to characterize the shear resistance of composite materials with highly nonlinear shear response. The correction factors, which are needed to compensate for the nonuniformity of the shear stress or strain distribution in the specimen test section for shear modulus measurement, have to be defined carefully. Strain contours in the nonlinear response ranges are presented and the initiation of failure in the notch regions is investigated.

Ho, Henjen↗

NASA NTRS1999

Transduction-like gene transfer in the methanogen Methanococcus voltae

Strain PS of Methanococcus voltae (a methanogenic, anaerobic archaebacterium) was shown to generate spontaneously 4.4-kbp chromosomal DNA fragments that are fully protected from DNase and that, upon contact with a cell, transform it genetically. This activity, here called VTA (voltae transfer agent), affects all markers tested: three different auxotrophies (histidine, purine, and cobalamin) and resistance to BES (2-bromoethanesulfonate, an inhibitor of methanogenesis). VTA was most effectively prepared by culture filtration. This process disrupted a fraction of the M. voltae cells (which have only an S-layer covering their cytoplasmic membrane). VTA was rapidly inactivated upon storage. VTA particles were present in cultures at concentrations of approximately two per cell. Gene transfer activity varied from a minimum of 2 x 10(-5) (BES resistance) to a maximum of 10(-3) (histidine independence) per donor cell. Very little VTA was found free in culture supernatants. The phenomenon is functionally similar to generalized transduction, but there is no evidence, for the time being, of intrinsically viral (i.e., containing a complete viral genome) particles. Consideration of VTA DNA size makes the existence of such viral particles unlikely. If they exist, they must be relatively few in number;perhaps they differ from VTA particles in size and other properties and thus escaped detection. Digestion of VTA DNA with the AluI restriction enzyme suggests that it is a random sample of the bacterial DNA, except for a 0.9-kbp sequence which is amplified relative to the rest of the bacterial chromosome. A VTA-sized DNA fraction was demonstrated in a few other isolates of M. voltae.

Methanococcus/genetics/growth & development/metabo↗

NASA NTRS2009

Capillary Corner Flows With Partial and Nonwetting Fluids

Capillary flow in containers or conduits with interior corners are common place in nature and industry. The majority of investigations addressing such flows solve the problem numerically in terms of a friction factor for flows along corners with contact angles below the Concus-Finn critical wetting condition for the particular conduit geometry of interest. This research effort provides missing numerical data for the flow resistance function F(sub i) for partially and nonwetting systems above the Concus-Finn condition. In such cases the fluid spontaneously de-wets the interior corner and often retracts into corner-bound drops. A banded numerical coefficient is desirable for further analysis and is achieved by careful selection of length scales x(sub s) and y(sub s) to nondimensionalize the problem. The optimal scaling is found to be identical to the wetting scaling, namely x(sub s) = H and y(sub s) = Htan (alpha), where H is the height from the corner to the free surface and a is the corner half-angle. Employing this scaling produces a relatively weakly varying flow resistance F(sub i) and for subsequent analyses is treated as a constant. Example solutions to steady and transient flow problems are provided that illustrate applications of this result.

Bolleddula, D. A.↗

DOE OSTI2019

Impact of Water Ingress on Molybdenum Thin Films and Its Effect on Cu(In,Ga)Se 2 Solar Cells

Solar cell degradation can occur through many pathways and at the different stages of the fabrication process, notably because of the water condensation. In the case of Cu(In,Ga)Se 2 (CIGS) solar cells, the impact of water ingress on Mo back contact can be substantial for not only the film itself but also the device performance and reliability. Microstructural modification, change in film morphology, loss in reflectance, and increased resistivity because of the moisture ingress were observed via X-ray diffraction, transmission electron microscopy, spectroscopic ellipsometry, and four-point probe measurements, respectively. Secondary ion mass spectrometry measurements revealed drastic changes in the alkali (Na, K) profiles in both the CIGS and Mo layers, likely because of the modification of their diffusion coefficient through Mo. This, in turn, negatively impacts the solar cell efficiency by decreasing both fill factor and open-circuit voltage. Additional experiments, modifying the substrate and utilizing a NaF postdeposition treatment, highlight the mechanisms of degradation as being due to both a modification of the Mo/CIGS interface and the lack of alkali diffusion after water ingress.

14 SOLAR ENERGY↗

DOE OSTI2021

An Electrochemically Activated Nanofilm for Sustainable Mg Anode with Fast Charge Transfer Kinetics

Highly reversible Mg plating/stripping is key for rechargeable Mg batteries and has typically been successfully demonstrated using transient electrochemical techniques such as cyclic voltammetry measurements. Furthermore, little effort has been invested in studying the stability of the electrode/electrolyte interface over an extended time. We report here the development of an in situ generated surface film for Mg anodes based on electrodeposited bismuth (E_Bi). This film improves the interfacial stability of Mg in contact with the electrolyte, particularly over an extended time, and possesses fast charge-transfer kinetics (<30 Ω∙cm 2 ) and low non-time-sensitive interfacial film resistance (ca. 5 Ω∙cm 2 ) for active Mg species.

25 ENERGY STORAGE↗

DOE OSTI2023

Chemically Stable Styrenic Electrospun Membranes with Tailorable Surface Chemistry

Membranes with tailorable surface chemistry have applications in a wide range of industries. Synthesizing membranes from poly(chloromethyl styrene) directly incorporates an alkyl halide surface-bound initiator which can be used to install functional groups via SN2 chemistry or graft polymerization techniques. In this work, poly(chloromethyl styrene) membranes were synthesized through electrospinning. After fabrication, membranes were crosslinked with a diamine, and the chemical resistance of the membranes was evaluated by exposure to 10 M nitric acid, ethanol, or tetrahydrofuran for 24 h. The resulting membranes had diameters on the order of 2–5 microns, porosities of >80%, and permeance on the order of 10,000 L/m2/h/bar. Crosslinking the membranes generally increased the chemical stability. The degree of crosslinking was approximated using elemental analysis for nitrogen and ranged from 0.5 to 0.9 N%. The poly(chloromethyl styrene) membrane with the highest degree of crosslinking did not dissolve in THF after 24 h and retained its high permeance after solvent exposure. The presented chemically resistant membranes can serve as a platform technology due to their versatile surface chemistry and can be used in membrane manufacturing techniques that require the membrane to be contacted with organic solvents or monomers. They can also serve as a platform for separations that are performed in strong acids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1984

Low-Thermal-Resistance Baseplate Mounting

Low-thermal-resistance mounting achieved by preloading baseplate to slight convexity with screws threaded through beam. As mounting bolts around edge of base-place tightened, baseplate and cold plate contact first in center, with region of intimate contact spreading outward as bolts tightened.

Perreault, W. T.↗