Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CALORIMETRY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

Kinetics of a transient silicide during the reaction of Ni thin film with (100)Si

In situ measurements of the kinetics of the transient {theta}-Ni{sub 2}Si phase formation have been obtained by x-ray diffraction and differential scanning calorimetry. A possible mechanism for the transient phase is proposed. It allows to simulate the growth and the consumption of the {theta}-Ni{sub 2}Si during the growth of the {delta}-Ni{sub 2}Si silicide.

36 MATERIALS SCIENCE↗

The effect of cooling rates on the apparent fragility of Zr-based bulk metallic glasses

We investigate the behavior of the kinetic fragility parameter D* as different cooling rates are applied to samples of the Zr{sub 57}Cu{sub 15.4}Ni{sub 12.6}Al{sub 10}Nb{sub 5} and Zr{sub 58.5}Cu{sub 15.6}Ni{sub 12.8}Al{sub 10.3}Nb{sub 2.8} bulk metallic glass formers. The glassy samples are heated into the supercooled liquid region using differential scanning calorimetry (DSC) and cooled back into the glassy state with sets of different cooling rates, q{sub C}. The shifts in the glass transition are measured by determining the onset glass transition temperature, T{sub g}{sup onset}, as well as the limiting fictive temperature, T{sub f}{sup '}, upon reheating with a set of heating rates, q{sub H}. We then model the data by assuming a Vogel-Fulcher-Tammann-type behavior in the structural relaxation time, {tau}, and observe an apparent increase in the kinetic fragility parameter for slower cooling rates. These results show that fragilities calculated from DSC scans, where q{sub H}=q{sub C} are in good agreement with those from equilibrium viscosity data recently obtained by three-point beam-bending.

36 MATERIALS SCIENCE↗

Thermo-mechanical and electrical properties of epoxy composites containing ceramic nanofillers

Epoxy nanocomposites with ceramic nanoparticles, i.e. Al{sub 2}O{sub 3}, Tio{sub 2} and SiO{sub 2}, were prepared by combined dispersion techniques, namely mechanical mixing and sonication. The influence of fillers addition on thermal, mechanical and dielectric properties have been investigated by means of Differential Scanning Calorimetry (DSC), Dynamic-mechanical analysis (DMA) and dielectric spectroscopy to measure the dielectric permittivity, tan delta and volume resistivity. Morphological investigations by Scanning Electron Microscopy (SEM) has been also performed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Kinetic Study of Crystallization Process in Fe{sub 32}Ni{sub 36}Cr{sub 14}P{sub 12}B{sub 6} Metallic Glass

Kinetics of crystallization process in a Fe-based metallic glass 2826A (Fe{sub 32}Ni{sub 36}Cr{sub 14}P{sub 12}B{sub 6}) has been studied with the help of differential scanning calorimetry(DSC). It is found that the 2826A metallic glass exhibits two overlapping crystallization peaks. The activation energy for crystallization (E) and the Avrami exponent (n) for the two crystallization peaks have been obtained using the Kolmogorov-Jhonson-Mehl-Avrami (KJMA) equation. The so-obtained values of E and n have been utilized to derive normalized heat flow curves. It has been observed that the theoretical heat flow curves obtained using KJMA equation show large deviations from the experimental curves for the first peak whereas the curves are in very close agreement for the second peak. This suggests that kinetics of crystallization process during the first peak cannot be described correctly in KJMA formalism.

36 MATERIALS SCIENCE↗

High Temperature Decomposition of Almandine and Pyrope in Reducing Atmosphere

Thermal decomposition of two garnets of near end-member composition--almandine (Fe{sub 2.85}Mg{sub 0.15})(Al{sub 1.99})Si{sub 2.99}O{sub 12} and pyrope (Mg{sub 2.22}Fe{sub 0.47}Ca{sub 0.33})(Cr{sub 0.11}Fe{sub 0.06}Al{sub 1.81})Si{sub 2.98}O{sub 12}--has been carried out in reducing atmosphere (forming gas: 10% of H{sub 2} in N{sub 2}). High-temperature behavior of both samples was monitored using simultaneous thermogravimetry and differential scanning calorimetry. The decomposition of almandine and pyrope turned out to proceed at slightly different temperatures above 1000 degree sign C. Therefore, two series of samples were prepared based on the results of thermal analysis: almandine heated up to 950 deg. C, 1070 deg. C and 1200 deg. C, and pyrope heated up to 1000 deg. C, 1100 deg. C, 1125 deg. C and 1200 deg. C. The identification of the decomposition products was performed by X-ray powder diffraction and Moessbauer spectroscopy. The common feature of the decomposition of both garnets is the presence of metallic iron and spinel phase, while the other products include fayalite, cristobalite, and cordierite for almandine; and enstatite and anorthite for pyrope. The formation of this last component was enabled due to Ca content in pyrope.

36 MATERIALS SCIENCE↗

Investigation of anti-Relaxation coatings for alkali-metal vapor cells using surface science techniques

Many technologies based on cells containing alkali-metal atomic vapor benefit from the use of antirelaxation surface coatings in order to preserve atomic spin polarization. In particular, paraffin has been used for this purpose for several decades and has been demonstrated to allow an atom to experience up to 10?000 collisions with the walls of its container without depolarizing, but the details of its operation remain poorly understood. We apply modern surface and bulk techniques to the study of paraffin coatings in order to characterize the properties that enable the effective preservation of alkali spin polarization. These methods include Fourier transform infrared spectroscopy, differential scanning calorimetry, atomic force microscopy, near-edge x-ray absorption fine structure spectroscopy, and x-ray photoelectron spectroscopy. We also compare the light-induced atomic desorption yields of several different paraffin materials. Experimental results include the determination that crystallinity of the coating material is unnecessary, and the detection of C=C double bonds present within a particular class of effective paraffin coatings. Further study should lead to the development of more robust paraffin antirelaxation coatings, as well as the design and synthesis of new classes of coating materials.

36 MATERIALS SCIENCE↗

Multilayered Al/CuO thermite formation by reactive magnetron sputtering: Nano versus micro

Multilayered Al/CuO thermite was deposited by a dc reactive magnetron sputtering method. Pure Al and Cu targets were used in argon-oxygen gas mixture plasma and with an oxygen partial pressure of 0.13 Pa. The process was designed to produce low stress (<50 MPa) multilayered nanoenergetic material, each layer being in the range of tens nanometer to one micron. The reaction temperature and heat of reaction were measured using differential scanning calorimetry and thermal analysis to compare nanostructured layered materials to microstructured materials. For the nanostructured multilayers, all the energy is released before the Al melting point. In the case of the microstructured samples at least 2/3 of the energy is released at higher temperatures, between 1036 and 1356 K.

36 MATERIALS SCIENCE↗

Structural, thermal, optical, and photoacoustic study of nanocrystalline Bi{sub 2}Te{sub 3} produced by mechanical alloying

Nanocrystalline Bi{sub 2}Te{sub 3} was produced by mechanical alloying and its properties were investigated by differential scanning calorimetry (DSC) x-ray diffraction (XRD), Raman spectroscopy (RS), and photoacoustic spectroscopy (PAS). Combining the XRD and RS results, the volume fraction of the interfacial component in as-milled and annealed samples was estimated. The PAS results suggest that the contribution of the interfacial component to the thermal diffusivity of nanostructured Bi{sub 2}Te{sub 3} is very significant.

36 MATERIALS SCIENCE↗

Probing Martensitic Transition in Nitinol Wire: A Comparison of X-ray Diffraction and Other Techniques

Martensitic to austenite transformation in Nitinol wire can be measured by a number of techniques such as XRD (X-Ray Diffraction), DSC (Differential Scanning Calorimetry), BFR (Bend and Free Recovery) and Vickers indentation recovery. A comparison of results from these varied characterisation techniques is reported here to obtain a greater understanding of the thermal-elastic-structural changes associated with martensitic transformation. The transformation temperatures measured by DSC were found to correspond well with the structural and mechanical information obtained from XRD, BFR and Vickers indent recovery methods. Indent recovery is a relatively new and accurate method of monitoring stress induced martensitic transformations in NiTi and is one of only a few methods of stress inducing martensitic transformation in large scale samples. It is especially useful for NiTi in the as-cast billet form, where tensile testing is impossible. BFR is uniquely popular in the NiTi wire manufacturing sector and is recognised as the most accurate method of measuring the transformation temperature. Here the material is stressed to a representative in-service stress level during the test. No other test uses the shape memory effect for measuring the transformation temperature of NiTi. The results show that the DSC thermogram and XRD diffractogram have a peak overlap which is a common occurrence in NiTi that has been extensively processed. The XRD method further explains the observations in the DSC thermogram and in combination they confirm the transformation temperature.

36 MATERIALS SCIENCE↗

Structure and mechanical properties of Al-3Fe rapidly solidified alloy

The Al based Al-3 wt%Fe alloy was prepared by conventionally casting (ingot) and further processed the melt-spinning technique and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) together with energy dispersive spectroscopy (EDS), differential scanning calorimetry (DSC) and the Vickers microhardness tester. The rapidly solidified (RS) binary alloys were composed of supersaturated {alpha}-Al solid solution and finely dispersed intermetallic phases. Experimental results showed that the mechanical properties of RS alloys were enhanced, which can be attributed to significant changes in the microstructure. The dependence of microhardness H{sub V} on the solidification rate (V) was analysed. These results showed that with the increasing values of V, the values of H{sub V} increased.

36 MATERIALS SCIENCE↗

Large-Area Fast-Timing Systems In STAR

The STAR experiment at RHIC concentrates on the tracking of charged hadrons via ionization, and the detection of electrons and photons via calorimetry, in a wide and azimuthally complete acceptance. STAR's ability to directly identify charged hadrons was initially limited to low momenta. This has been addressed via the construction of a large-area Time-of-Flight (TOF) system based on small Multigap Resistive Plate Chambers (MRPCs). The installation of the STAR TOF system was completed last fall. The full system is ran well in the recent RHIC Run 10. The operation of the system, and its performance for particle identification, during RHIC Runs 9 and 10 will be described. STAR's ability to identify muons is also extremely limited. Another large-area TOF system based on much larger MRPCs is envisioned. This system will be located outside the STAR magnet and is called the Muon Telescope Detector (MTD). Several different prototype MTD systems were operated in Runs 7 through 10, and a patch of near-final MTD detectors is under construction for use in the upcoming Run 11. The performance of the MTD prototype detectors, and the design of the Run 11 installation and the full system, will be described.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Heat Capacity And Structural Relaxation In Se{sub 80-x}Te{sub 20}Ag{sub x}(x = 3 and 9) Glassy Alloys

This paper reports the effects of annealing time and temperature on the thermodynamics of enthalpy relaxation of Se{sub 80-x}Te{sub 20}Ag{sub x} (x = 3,9) glasses. Differential Scanning Calorimetry (DSC) method is optimized for the measurement of enthalpy relaxation in the vicinity of glass transition. The recovery of excess enthalpy ({Delta}H{sub excess}) has been calculated from the knowledge of excess specific heat ({Delta}C{sub p}). It is found that excess enthalpy released ({Delta}H{sub excess}) increase with increase in annealing time (t{sub a}). From the knowledge of excess specific heat ({Delta}C{sub p}) and {Delta}H{sub excess}, it has been found that sub-T{sub g} annealing of glass leads to decrease in enthalpy of the system and thereby taking it to the more equilibrium state.

36 MATERIALS SCIENCE↗

Thermal studies of Se{sub 85-x}Te{sub 15}In{sub x} (x = 3,6,9,12) glasses

Bulk glasses of compositions Se{sub 85-x}Te{sub 15}In{sub x} (x = 3,6,9,12) are prepared by melt quenching technique and Differential scanning calorimetry (DSC) is employed to study the thermal stability, crystallization mechanism as well as specific heat of these glasses. It is found that the addition of indium increases the glass transition temperature. From the heating rate dependence of the glass transition temperature the activation energy of glass transition is determined using Kissinger's equation for non-isothermal crystallization of materials. An attempt has been made to explain the variation in the value of T{sub c}, T{sub p} and {Delta}C{sub p} for the composition Se{sub 73}Te{sub 15}In{sub 12} using rigidity percolation threshold (RPT). From the values of (T{sub c}-T{sub g}) the stable glass system is determined.

36 MATERIALS SCIENCE↗

Influence of Al/CuO reactive multilayer films additives on exploding foil initiator

An investigation on the influence of Al/CuO reactive multilayer films (RMFs) additives on exploding foil initiator was performed in this paper. Cu film and Cu/Al/CuO RMFs were produced by using standard microsystem technology and RF magnetron sputtering technology, respectively. Scanning electron microscopy characterization revealed the distinct layer structure of the as-deposited Al/CuO RMFs. Differential scanning calorimetry was employed to ascertain the amount of heat released in the thermite reaction between Al films and CuO films, which was found to be 2024 J/g. Electrical explosion tests showed that 600 V was the most matching voltage for our set of apparatus. The explosion process of two types of films was observed by high speed camera and revealed that compared with Cu film, an extra distinct combustion phenomenon was detected with large numbers of product particles fiercely ejected to a distance of about six millimeters for Cu/Al/CuO RMFs. By using the atomic emission spectroscopy double line technique, the reaction temperature was determined to be about 6000-7000 K and 8000-9000 K for Cu film and Cu/Al/CuO RMFs, respectively. The piezoelectricity of polyvinylidene fluoride film was employed to measure the average velocity of the slapper accelerated by the explosion of the films. The average velocities of the slappers were calculated to be 381 m/s and 326 m/s for Cu film and Cu/Al/CuO RMFs, respectively, and some probable reasons were discussed with a few suggestions put forward for further work.

36 MATERIALS SCIENCE↗

Tore Supra LH transmitter upgrade, a new RF driver for the power spectrum

New real time tools have been developed for testing new 700kW/3.7GHz/CW klystrons and for the operations on very long plasma shots. After the commissioning of the 18 series tubes on the high power test bed facility, the installation of the first 8 klystrons in the Tore Supra transmitter and the adjustment tests on load, this upgrade work has been materialized during the last 2010 campaign by a successful operation on the Full Active Multijunction (FAM) C3 antenna, with new performances: 3.5MW/40s on plasma. The RF output power control in amplitude and phase has been improved for a better control of the wave spectrum launched into the plasma. The new klystrons have no modulating anode and the high cathode voltage must be adjusted with the RF input power in order to optimize the RF output power with a minimization of the thermal power losses in the collector. A new phase correction, depending on the 3 RF output power ranges used, has been introduced. The improvements made in 2009 and 2010 on the generic phase loop and the procedures used during the real time tests of the RF transfer functions in amplitude and phase are detailed below. All RF measurements systems, RF safety systems and the RF calibration procedures have been revised in order to have the best consistency, reproducibility and with a measurement error against the calorimetry measurement lower than 10%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermodynamic, Raman and electrical switching studies on Si{sub 15}Te{sub 85-x}Ag{sub x} (4 {<=} x {<=} 20) glasses

We have investigated thermal properties of bulk Si{sub 15}Te{sub 85-x}Ag{sub x} (4 {<=} x {<=} 20) glasses in detail, through alternating differential scanning calorimetry experiments. The composition dependence of thermal parameters reveal the signatures of rigidity percolation and chemical threshold at compositions x = 12 and x = 19, respectively. The stability and glass forming ability of these glasses have also been determined using the data obtained from different thermodynamic quantities and it is found that the Si{sub 15}Te{sub 85-x}Ag{sub x} glasses in the region 12 {<=} x {<=} 17 are more stable when compared to other glasses of the same series. Further, the blueshift observed in Raman spectroscopy investigations, in the composition range 12 {<=} x {<=} 13, support the occurrence of stiffness threshold in this composition range. All Si{sub 15}Te{sub 85-x}Ag{sub x} (4 {<=} x {<=} 20) glasses are found to exhibit memory type switching (for sample thickness 0.25 mm) in the input current range 3-9 mA. The effect of rigidity percolation and chemical thresholds on switching voltages are observed at x = 12 and 19, respectively.

36 MATERIALS SCIENCE↗

The effect of 100 MeV oxygen ion on electrical and optical properties of nonlinear optical l-alanine sodium nitrate single crystals

Single crystals of nonlinear optical (NLO) L-alanine Sodium Nitrate (LASN) were grown by slow evaporation method. The grown crystals were irradiated by 100 MeV oxygen ions with the cumulative doses of 1Mrad, 6 Mrad and 10 Mrad. The dielectric properties, differential scanning calorimetry (DSC) and second harmonic generation (SHG) of the crystals were studied before and after irradiation. The dielectric constant was found to increase after irradiation. The DSC reveals that the melting point remains unaffected due to irradiation. The SHG efficiency of LASN was found to decrease with increase in radiation dose.

36 MATERIALS SCIENCE↗

Glycine phases formed from frozen aqueous solutions: Revisited

Glycine phases formed when aqueous solutions were frozen and subsequently heated under different conditions were studied by Raman scattering, x-ray diffraction, and differential scanning calorimetry (DSC) techniques. Crystallization of ice I{sub h} was observed in all the cases. On cooling at the rates of 0.5 K/min and 5 K/min, glassy glycine was formed as an intermediate phase which lived about 1 min or less only, and then transformed into {beta}-polymorph of glycine. Quench cooling of glycine solutions (15% w/w) in liquid nitrogen resulted in the formation of a mixture of crystalline water ice I{sub h} and a glassy glycine, which could be preserved at cryogenic temperatures (80 K) for an indefinitely long time. This mixture remained also quite stable for some time after heating above the cryogenic temperature. Subsequent heating under various conditions resulted in the transformation of the glycine glass into an unknown crystalline phase (glycine 'X-phase') at 209-216 K, which at 218-226 K transformed into {beta}-polymorph of glycine. The 'X-phase' was characterized by Raman spectroscopy; it could be obtained in noticeable amounts using a special preparation technique and tentatively characterized by x-ray powder diffraction (P2, a= 6.648 A, b= 25.867 A, c= 5.610 A, {beta}= 113.12 Masculine-Ordinal-Indicator ); the formation of 'X-phase' from the glycine glassy phase and its transformation into {beta}-polymorph were followed by DSC. Raman scattering technique with its power for unambiguous identification of the crystalline and glassy polymorphs without limitation on the crystallite size helped us to follow the phase transformations during quenching, heating, and annealing. The experimental findings are considered in relation to the problem of control of glycine polymorphism on crystallization.

36 MATERIALS SCIENCE↗