Results for “Boundary Layer Stability” — Page 52

NASA NTRS1990

Numerical simulation of transition in a rotating disk flow

An investigation of the laminar-turbulence transition process in a three-dimensional boundary layer on a rotating disk is initiated. Preliminary results from a direct numerical simulation using spectral collocation method are presented. The simulation results in the linear regime is tested against linear stability theory. Saturation of the primary disturbance energy suggests the importance of modal interaction in initiating transition.

Balachandar, S.↗

NASA NTRS1993

Effect of micron-sized roughness on transition in swept-wing flows

Boundary-layer transition-to-turbulence studies are conducted in the Arizona State University Unsteady Wind Tunnel on a 45-degree swept airfoil. The pressure gradient is designed so that the initial stability characteristics are purely crossflow-dominated. Flow visualization and hot-wire measurements show that the development of the crossflow vortices is influenced by roughness near the attachment-line. Comparisons of transition location are made between a painted surface, a machine-polished surface, and a hand-polished surface. Then, isolated 6 micron roughness elements are placed near the attachment line on the airfoil surface under conditions of the final polish (0.25 micron rms). These elements amplify a centered stationary crossflow vortex and its neighbors, resulting in localized early transition. The diameter, height, and location of these roughness elements are varied in a systematic manner. Spanwise hot-wire measurements are taken behind the roughness element to document the enhanced vortices. These scans are made at several different chord locations to examine vortex growth.

Radeztsky, Ronald H., Jr.↗

NASA NTRS2019

Dynamic Analysis of the STARC-ABL Propulsion System

In the pursuit of Electrified Aircraft Propulsion (EAP), much of the attention is on the development of hybrid electric concept vehicles and their propulsion systems from a steady state performance perspective. While it is steady-state performance that largely determines the efficiency of civil air transports, engine operability and transient performance define constraints for the steady state design that impact efficiency and system viability. Neglecting dynamics and control technologies can result in an over-designed, sub optimal propulsion system or a concept that is not feasible. Thus, dynamic system studies were conducted on the propulsion system of the conceptual aircraft design known as the Single-aisle Turboelectric AiRCraft with Aft Boundary Layer propulsor (STARC-ABL). This paper describes the development of a controller to verify the baseline concept's feasibility from an operability perspective. Further, studies were conducted to identify excessive stability margin in the baseline design that could be traded for potential benefits in efficiency through an engine re design. This study revealed the potential to reduce the high pressure compressor (HPC) stall margin by 3%. Finally, a study was conducted to investigate the potential benefit of adding energy storage to the STARC-ABL concept that further improves operability and enables more gains in engine efficiency and performance. The energy storage provided an additional 0.5% stall margin can be removed from the HPC.

STARC-ABL↗

NASA NTRS2019

Dynamic Analysis of the STARC-ABL Propulsion System

In the pursuit of Electrified Aircraft Propulsion (EAP), much of the attention is on the development of hybrid electric concept vehicles and their propulsion systems from a steady state performance perspective. While it is steady-state performance that largely determines the efficiency of civil air transports, engine operability and transient performance define constraints for the steady state design that impact efficiency and system viability. Neglecting dynamics and control technologies can result in an over-designed, sub optimal propulsion system or a concept that is not feasible. Thus, dynamic system studies were conducted on the propulsion system of the conceptual aircraft design known as the Single-aisle Turboelectric AiRCraft with Aft Boundary Layer propulsor (STARC-ABL). This paper describes the development of a controller to verify the baseline concept's feasibility from an operability perspective. Further, studies were conducted to identify excessive stability margin in the baseline design that could be traded for potential benefits in efficiency through an engine re design. This study revealed the potential to reduce the high pressure compressor (HPC) stall margin by 3%. Finally, a study was conducted to investigate the potential benefit of adding energy storage to the STARC-ABL concept that further improves operability and enables more gains in engine efficiency and performance. The energy storage provided an additional 0.5% stall margin can be removed from the HPC.

STARC-ABL↗

NASA NTRS2019

Dynamic Analysis of the STARC-ABL Propulsion System

In the pursuit of Electrified Aircraft Propulsion (EAP), much of the attention is on the development of hybrid electric concept vehicles and their propulsion systems from a steady state performance perspective. While it is steady-state performance that largely determines the efficiency of civil air transports, engine operability and transient performance define constraints for the steady state design that impact efficiency and system viability. Neglecting dynamics and control technologies can result in an over-designed, sub optimal propulsion system or a concept that is not feasible. Thus, dynamic system studies were conducted on the propulsion system of the conceptual aircraft design known as the Single-aisle Turboelectric AiRCraft with Aft Boundary Layer propulsor (STARC-ABL). This paper describes the development of a controller to verify the baseline concept's feasibility from an operability perspective. Further, studies were conducted to identify excessive stability margin in the baseline design that could be traded for potential benefits in efficiency through an engine re design. This study revealed the potential to reduce the high pressure compressor (HPC) stall margin by 3%. Finally, a study was conducted to investigate the potential benefit of adding energy storage to the STARC-ABL concept that further improves operability and enables more gains in engine efficiency and performance. The energy storage provided an additional 0.5% stall margin can be removed from the HPC.

dynamic systems analysis↗

DOE OSTI2025

Characterization of Flashback and Flame-Holding in a Jet-In-Crossflow Mixing Configuration with Methane-Hydrogen Fuel Blends

An approach that combines experimental and numerical analyses has been implemented to characterize the fundamentals of flashback events and flame-holding phenomena during high-hydrogen combustion in a jet-in-crossflow (JICF) configuration. Such flame dynamics are visualized experimentally using nanosecond (ns)-based hydroxyl planar laser-induced fluorescence (OH-PLIF) and chemiluminescence (CL) diagnostics techniques. The JICF burner has an optically accessible pre-mixing tube allowing the optical diagnostics. The testing was conducted for varied pre-mixer velocities (V) and equivalence ratio (ϕ) for 90%-100% (H2, by mole) H2/CH4 reactant mixtures at atmospheric temperature and pressure conditions. Two distinct flashbacks were identified – conventional rich flashback and lean flashback, recorded while increasing ϕ and decreasing ϕ, respectively. The cause of lean flashback was attributed to lower flux ratio which bends the jet sharply, closer toward the injection plane. The flashback was found to occur along the boundary layer, assisted by the inner wall of the pre-mixer tube. The mean OH-PLIF images characterized the flame-holding behavior where the flame was found to be stabilized on the leeward side only or on both windward and leeward sides as a lifted flame near the fuel port.

flame holding↗

DOE OSTI2025

Experimental Measurements of Soot and Soot Precursors of Sustainable Aviation Fuels

Sustainable Aviation Fuels (SAFs) are promising for decarbonizing the challenging-to-electrify aerospace sector and reducing yearly greenhouse gas emissions by thousands of tons. Developing predictive detailed chemical kinetic models for SAF (and traditional) fuel mixtures necessitates a robust experimental database to elucidate the intricate pyrolysis and oxidation chemistry of SAF fuel blend components. Two critical components of SAF surrogate mixtures are iso-dodecane isomers and trans-decalin. This report characterizes the structure of three slightly sooting, laminar, non-premixed, nitrogen-diluted Planar Mixing Layer Flames (PMLFs) fueled by either pure ethylene, ethylene doped with 1500ppm of either 2,2,4,6,6-pentamethyl-heptane or trans-decalin. The flames have the same stoichiometric mixture fraction and total mole fraction of fuels in the fuel stream (X F,F = X C2H4,F + X Dopant,F = 0.26), resulting in approximately the same maximum temperature (T max ≈ 1800 K) to highlight the effect of doping on soot and its gaseous precursors. The PMLF is unconfined and established between adjacent planar jets of the fuel and oxidizer streams surrounded by annular shielding nitrogen. The flow is stabilized by exhausting the hot buoyant flame products through a slot in a downstream plate onto which the cold flow impinges. Importantly, any horizontal cross-section of the PMLF has a self-similar thermochemical structure of a reactive boundary layer that grows at increasing Height Above the Burner (HAB). Therefore, the horizontal cross-sections of a PMLF can be modeled as a One-Dimensional Counterflow Flame (1D-CF) with very low strain rates which are unachievable in traditional CFs and yield a structure that is several millimeters thick. In brief, the PMLF is ideal for performing spatially resolved measurements with minimal effects of the sampling-induced perturbations, to develop and validate detailed chemical kinetic models on time scales of a few tens of milliseconds that are relevant in aviation applications. The horizontal profiles of C0-C18 gaseous species at HAB = 50 mm and soot volume fraction at 25 and 50 mm are measured using capillary sampling followed by GC-MS analyses and Laser Induced Emission Spectroscopy (LIES), respectively. Additionally, the Elastic Laser Light Scattering (E-LLS) coefficient is measured at HAB = 50 mm and 25 mm to determine the strain rates of the 1D-CFs equivalent to the characterized PMLF horizontal cross sections and the profile of the E-LLS equivalent diameter of soot. The comparison of the results in the base PMLF fueled only by ethylene with those in either doped PMLF in which 1500 ppm of ethylene are replaced with 2,2,4,6,6-pentamethyl-heptane or trans-decalin, reveals that the doping increases the mole fraction of several Polycyclic Aromatic Hydrocarbons (PAHs) at both HABs by a factor of approximately 2.5, and the soot volume fraction at both HABs by factors of ~1.5 for 2,2,4,6,6-pentamethyl-heptane and ~1.25 for trans-decalin doping, respectively. Conversely, doping causes a near doubling of the soot equivalent diameter only at HAB = 50 mm, without significant effects at 25 mm. The experimental results partially validate the tested state-of-the-art detailed chemical kinetic model and also point toward the further improvement of its predictive capabilities.

10 SYNTHETIC FUELS↗

NASA NTRS2005

Linear Stability Analysis of Gravitational Effects on a Low-Density Gas Jet Injected into a High-Density Medium

The objective of this study was to determine the effects of buoyancy on the absolute instability of low-density gas jets injected into high-density gas mediums. Most of the existing analyses of low-density gas jets injected into a high-density ambient have been carried out neglecting effects of gravity. In order to investigate the influence of gravity on the near-injector development of the flow, a spatio-temporal stability analysis of a low-density round jet injected into a high-density ambient gas was performed. The flow was assumed to be isothermal and locally parallel; viscous and diffusive effects were ignored. The variables were represented as the sum of the mean value and a normal-mode small disturbance. An ordinary differential equation governing the amplitude of the pressure disturbance was derived. The velocity and density profiles in the shear layer, and the Froude number (signifying the effects of gravity) were the three important parameters in this equation. Together with the boundary conditions, an eigenvalue problem was formulated. Assuming that the velocity and density profiles in the shear layer to be represented by hyperbolic tangent functions, the eigenvalue problem was solved for various values of Froude number. The Briggs-Bers criterion was combined with the spatio-temporal stability analysis to determine the nature of the absolute instability of the jet whether absolutely or convectively unstable. The roles of the density ratio, Froude number, Schmidt number, and the lateral shift between the density and velocity profiles on the absolute instability of the jet were determined. Comparisons of the results with previous experimental studies show good agreement when the effects of these variables are combined together. Thus, the combination of these variables determines how absolutely unstable the jet will be.

Lawson, Anthony L.↗

NASA NTRS1974

Studies of heat source driven natural convection

Natural convection energy transport in a horizontal layer of internally heated fluid with a zero heat flux lower boundary, and an isothermal upper boundary, has been studied. Quantitative information on the time-mean temperature distribution and the fluctuating component of temperature about the mean temperature in steady turbulent convection are obtained from a small thermocouple inserted into the layer through the upper bounding plate. Data are also presented on the development of temperature at several vertical positions when the layer is subject to both a sudden increase and to a sudden decrease in power input. For changes of power input from zero to a value corresponding to a Rayleigh number much greater than the critical linear stability theory value, a slight hysteresis in temperature profiles near the upper boundary is observed between the heat-up and cool-down modes.

Kulacki, F. A.↗

DOE OSTI2024

Implementation and Validation of a Generalized Actuator Disk Parameterization for Wind Turbine Simulations Within the FastEddy Model

ABSTRACT Fast and accurate large‐eddy simulation (LES) of the atmospheric boundary layer plays a crucial role in advancing wind energy research. Long‐duration wind farm studies at turbine‐resolving scales have become increasingly important to understand the intricate interactions between large wind farms and the atmospheric boundary layer. However, the prohibitive computational cost of these turbulence‐ and turbine‐resolving simulations has precluded such modeling to be exercised on a regular basis. To that end, we implement and validate the generalized actuator disk (GAD) model in the computationally efficient, graphics processing unit (GPU)–resident, LES model FastEddy. We perform single‐turbine simulations under three atmospheric stabilities (neutral, unstable, and stable) and compare them against observations from the Scaled Wind Farm Technology (SWiFT) facility and other LES codes from the recent Wakebench turbine wake model benchmark. Our idealized LES results agree well with observed wake velocity deficit and downstream recovery across stability regimes. Turbine response in terms of rotational speed, generated power, torque, and thrust coefficient are well predicted across stability regimes and are consistent with the LES results from the benchmark. The FastEddy simulations are found to be at least two orders of magnitude more efficient than the traditional CPU‐based LES models, opening the door for realistic LES simulations of full wind plants as a viable standard practice.

17 WIND ENERGY↗

NASA NTRS1980

Experimental investigation of a 0.15 scale model of a conformal variable-ramp inlet for the F-16 airplane

A 0.15 scale model of a proposed conformal variable-ramp inlet for the Multirole Fighter was tested from Mach 0.8 to 2.2 at a wide range of angles of attack and sideslip. Inlet ramp angle was varied to optimize ramp angle as a function of engine airflow, Mach number, angle of attack, and angle of sideslip. Several inlet configuration options were investigated to study their effects on inlet operation and to establish the final flight configuration. These variations were cowl sidewall cutback, cowl lip bluntness, boundary layer bleed, and first-ramp leading edge shape. Diagnostic and engine face instrumentation were used to evaluate inlet operation at various inlet stations and at the inlet/engine interface. Pressure recovery and stability of the inlet were satisfactory for the proposed application. On the basis of an engine stability audit of the worst-case instantaneous distortion patterns, no inlet/engine compatibility problems are expected for normal operations.

Hawkins, J. E.↗

NASA NTRS1975

Static longitudinal aerodynamic characteristics of a model with a modified 17 percent thick supercritical wing

The static longitudinal stability characteristics of a 0.09 scale model of an airplane with a modified 17 percent thick supercritical wing were investigated. Modifications were made to the wing to reduce a gradual buildup of boundary layer shock loss preceding drag divergence (drag creep) noted in an earlier investigation. The longitudinal aerodynamic characteristics were determined over a Mach number range from 0.30 to 0.76 at angles of attack that generally provided a lift coefficient range from 0 to buffet onset. Results indicate that the modifications to the airfoil essentially eliminated the drag creep associated with the airfoil that occurs between the critical Mach number and the drag divergence Mach number.

Ferris, J. C.↗

NASA NTRS1989

Bandwidth-limited robust nonlinear sliding control of pointing and tracking maneuvers

It is shown how multiaxial spacecraft tracking and pointing maneuvers with known control bandwidth and given tracking error bounds can be implemented by variable-structure control in the presence of uncertain vehicle and target dynamics. It is shown how to select a nonlinear sliding surface relating attitude and rate variables, as well as a Lyapunov function in the surface variables that absorbs multiplicative model undertainties, thereby simplifying the computation of control corrections. It is then shown how a boundary layer envelope can be designed, within which the components of the surface error dynamics can be modeled as the outputs of designer-selected decoupled low-pass filters. Closed-loop stability conditions accounting for the coupling between the attitude error dynamics and the surface error dynamics are then obtained.

Dwyer, Thomas A. W., III↗

NASA NTRS1987

Effects of acoustic sources

An experiment was conducted to determine the effect of acoustics on the laminar flow on the side of a nacelle. A flight test was designed to meet this goal and a brief review of the purpose is given. A nacelle with a significant length of laminar flow was mounted on the wing of NASA OV-1. Two noise sources are also mounted on the wing: one in the center body of the nacelle; the second in a wing mounted pod outboard of the nacelle. These two noise sources allow for a limited study of the effect of source direction in addition to control of the acoustic level and frequency. To determine the range of Tollmien-Schlichting frequencies, a stability analysis using the pressure coefficient distribution along the side of the nacelle was performed. Then by applying these frequencies and varying the acoustic level, a study of the receptivity of the boundary layer to the acoustic signal, as determined by the shortening of the length of laminar flow, was conducted. Results are briefly discussed.

Schoenster, James A.↗

NASA NTRS1990

Measurement of crossflow vortices, attachment-line flow, and transition using microthin hot films

A flow diagnostic experiment was conducted on a 45-deg swept-wing model using surface-mounted, multielement, microthin, hot-film sensors. The cross-flow vortex spacing, the attachment-line flow characteristics, and the transition region were all determined using an advanced data acquisition and instrumentation system. In addition to the frequencies of traveling waves predicted by linear stability theory, amplified disturbances at much higher frequencies were observed. Simultaneous measurements from sensors located at a number of chord and span locations highlighted the strong three-dimensionality of the boundary-layer flow in the presence of cross-flow vortices. The state of the attachment-line boundary layer was determined using a multielement sensor wrapped around the wing leading edge. The transition region flow characteristics were also identified.

Mangalam, S. M.↗

NASA NTRS1990

Transverse liquid fuel jet breakup, burning, and ignition

An analytical study of the breakup, burning, and ignition of liquid fuels injected transversely into a hot air stream is conducted. The non-reacting liquid jet breakup location is determined by the local sonic point criterion. Two models, one employing analysis of an elliptical jet cross-section and the other employing a two-dimensional blunt body to represent the transverse jet, were used for sonic point calculations. An auxiliary criterion based on surface tension stability is used as a separate means of determining the breakup location. For the reacting liquid jet problem, a diffusion flame supported by a one-step chemical reaction within the gaseous boundary layer is solved along the ellipse surface in subsonic cross flow. Typical flame structures and concentration profiles were calculated for various locations along the jet cross-section as a function of upstream Mach numbers. The integration reaction rate along the jet cross-section is used to predict ignition position, which is found to be situated near the stagnation point. While a multi-step reaction is needed to represent the ignition process more accurately, the present calculation does yield reasonable predictions concerning ignition along a curved surface.

Li, Hsi-Shang↗

NASA NTRS2011

Supersonic Mass Flux Measurements via Tunable Diode Laser Absorption and Non-Uniform Flow Modeling

Measurements of mass flux are obtained in a vitiated supersonic ground test facility using a sensor based on line-of-sight (LOS) diode laser absorption of water vapor. Mass flux is determined from the product of measured velocity and density. The relative Doppler shift of an absorption transition for beams directed upstream and downstream in the flow is used to measure velocity. Temperature is determined from the ratio of absorption signals of two transitions (lambda(sub 1)=1349 nm and lambda(sub 2)=1341.5 nm) and is coupled with a facility pressure measurement to obtain density. The sensor exploits wavelength-modulation spectroscopy with second-harmonic detection (WMS-2f) for large signal-to-noise ratios and normalization with the 1f signal for rejection of non-absorption related transmission fluctuations. The sensor line-of-sight is translated both vertically and horizontally across the test section for spatially-resolved measurements. Time-resolved measurements of mass flux are used to assess the stability of flow conditions produced by the facility. Measurements of mass flux are within 1.5% of the value obtained using a facility predictive code. The distortion of the WMS lineshape caused by boundary layers along the laser line-of-sight is examined and the subsequent effect on the measured velocity is discussed. A method for correcting measured velocities for flow non-uniformities is introduced and application of this correction brings measured velocities within 4 m/s of the predicted value in a 1630 m/s flow.

Chang, Leyen S.↗

NASA NTRS2019

Nonmodal Growth of TravelingWaves on Blunt Cones at Hypersonic Speeds

The existing database of transition measurements in hypersonic ground facilities has established that, as the nosetip bluntness is increased, the onset of boundary layer transition over a circular cone at zero angle of attack shifts downstream. However, this trend is reversed at sufficiently large values of the nose Reynolds number, so that the transition onset location eventually moves upstream with a further increase in nose-tip bluntness. Because modal amplification is too weak to initiate transition at moderate-to-large bluntness values, nonmodal growth has been investigated as the potential basis for a physics-based model for the frustum transition. The present analysis investigates the nonmodal growth of traveling disturbances initiated within the nose-tip vicinity that peak within the entropy layer. Results show that, with increasing nose bluntness, both planar and oblique traveling disturbances experience appreciable energy amplification up to successively higher frequencies. For moderately blunt cones, the initial nonmmodal growth is followed by a partial decay that is more than overcome by an eventual, modal growth as Mack-mode waves. For larger bluntness values, the Mack-mode waves are not amplified anywhere upstream of the experimentally measured transition location, but the traveling modes still undergo a significant amount of nonmodal growth. This finding does not provide a definitive link between optimal growth and the onset of transition, but it is qualitatively consistent with the experimental observations that frustum transition in the absence of sufficient Mack-mode amplification implies a double peak in disturbance amplification and the appearance of transitional events above the boundary-layer edge.

Hypersonic speed↗