Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Average Accuracy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Molecular-Beam Chopper and Four-Channel Amplifier

Molecular-beam chopper phase controller and timing interface is subsystem of four-stage, differentially pumped, modulated molecular-beam/mass spectrometer. Subsystem maintains accurate phase control and timing for repetitive signal averaging over several hours of operation. Chopper phase controller/ timing interface and four-channel programable time-multiplexed amplifier provide substantial improvements in attainable signal-to-noise ratio, detection limit, and accuracy of molecular-beam/mass-spectrometer system.

Adams, B. R.↗
NASA NTRS1985

A review of satellite altimeter measurement of sea surface wind speed - With a proposed new algorithm

The scheduled February 1985 launch of a radar altimeter aboard the U.S. Navy satellite Geosat has motivated an in-depth investigation of wind speed retrieval from satellite altimeters. The accuracy of sea surface wind speed estimated by the Seasat altimeter is examined by comparison with wind speed estimated by the Seasat scatterometer. The intercomparison is based on globally distributed spatial and temporal averages of the estimated wind speed. It is shown that there are systematic differences between altimeter and scatterometer wind speed estimates. These differences are traced to errors in the Seasat altimeter geophysical data record wind speed algorithm. A new algorithm is proposed which yields consistent estimates from the two satellite sensors. Using this new algorithm, the rms difference between spatial and temporal averages of the two wind speed estimates is less than 1 m/s, and their correlation is greater than 0.9.

Chelton, D. B.↗
NASA NTRS1992

A compressible Navier-Stokes solver with two-equation and Reynolds stress turbulence closure models

This report outlines the development of a general purpose aerodynamic solver for compressible turbulent flows. Turbulent closure is achieved using either two equation or Reynolds stress transportation equations. The applicable equation set consists of Favre-averaged conservation equations for the mass, momentum and total energy, and transport equations for the turbulent stresses and turbulent dissipation rate. In order to develop a scheme with good shock capturing capabilities, good accuracy and general geometric capabilities, a multi-block cell centered finite volume approach is used. Viscous fluxes are discretized using a finite volume representation of a central difference operator and the source terms are treated as an integral over the control volume. The methodology is validated by testing the algorithm on both two and three dimensional flows. Both the two equation and Reynolds stress models are used on a two dimensional 10 degree compression ramp at Mach 3, and the two equation model is used on the three dimensional flow over a cone at angle of attack at Mach 3.5. With the development of this algorithm, it is now possible to compute complex, compressible high speed flow fields using both two equation and Reynolds stress turbulent closure models, with the capability of eventually evaluating their predictive performance.

Navier-Stoke solver↗
NASA NTRS1992

Edge technique - Theory and application to the lidar measurement of atmospheric wind

The paper describes the theory of the edge technique, a powerful method for the detection and measurement of small frequency shifts. It can be employed with a lidar to obtain range-resolved measurements of wind with high accuracy and high vertical resolution. The technique can be applied to measure wind with a lidar by using either the aerosol or molecular backscattered signal. Simulations for a ground-based lidar at 1.06 micron using reasonable instrumental parameters show an accuracy of the vector components of the wind which is better than 0.5 m/s from the ground to an altitude of 20 km for a 100-m vertical resolution and a 100-shot average.

Korb, C. L.↗
NASA NTRS1998

The Role of Computational Fluid Dynamics at Marshall Space Flight Center

The Marshall Space Flight Center (MSFC) is the Center of Excellence for Space Propulsion Technology within NASA. One of MSFC's goals is to lower the cost of access to space. MSFC's Fluid Dynamics Division, a part of the Structures and Dynamics Lab, assists in accomplishing this goal. This division is divided into two branches: experimental and analytical, whose work is complimentary and integrated. In the analysis branch, the emphasis is to apply, rather than develop computational fluid dynamics (CFD), to reduce the cost of design and development of: (1) pump and turbine feedlines and feed manifolds; (2) all primary and secondary flow paths in pumps; (3) all primary and secondary flow paths in turbines; (4) combustion chambers; (5) rocket engine nozzles and plumes; and (6) launch vehicles ascent. The broad range of applications imposes unique constraints on the software. The use of CFD in evaluating rocket engine hardware, specifically, is of value due to several reasons: (1) Rocket engine hardware is extremely expensive to build and test; (2) high engineering and development cost is due to limited production; (3) the cost of one engine test is greater than the average yearly hardware and software cost; (4) CFD represents a relatively small investment relative to the impact it has on the engine development; and (5) computing costs are continuously decreasing. In terms of accuracy the predictable error is more useful than the inconsistent accuracy. The achievable accuracy varies from application to application. The lack of accuracy is often caused by improper analyses: such as improperly applied or located boundary conditions, or attempting steady analysis of unsteady flows. This report is in viewgraph format.

Garcia, Roberto↗
NASA NTRS2004

Improving the Representation of Land in Climate Models by Application of EOS Observations

The PI's IDS current and previous investigation has focused on the applications of the land data toward the improvement of climate models. The previous IDS research identified the key factors limiting the accuracy of climate models to be the representation of albedos, land cover, fraction of landscape covered by vegetation, roughness lengths, surface skin temperature and canopy properties such as leaf area index (LAI) and average stomatal conductance. Therefore, we assembled a team uniquely situated to focus on these key variables and incorporate the remotely sensed measures of these variables into the next generation of climate models.

Source record↗
NASA NTRSDate not supplied

TPSAS-NF1676L-29139-DND

The Arctic has been warming at a rate outpacing globally-averaged warming by 2-3 times, a phenomenon known as "Arctic Amplification" (AA). AA is evident in observations of Arctic surface temperature over the last century as well as in model predictions. The accuracy of model predictions is crucial to determine our response to climate change, as Arctic changes have consequences for the atmospheric circulation, sea level rise, and the carbon cycle. Unfortunately, models show a wide range of possible futures and intermodel spread in projections of Arctic temperature is larger than for any other region: a 2°C global temperature increase- the limit set by the Paris Climate Agreement- would lead to an Arctic temperature change between 3-7°C according to Coupled Model Intercomparison 5 (CMIP5) models. This intermodel spread represents a key deficiency in the understanding of Arctic feedback processes and how changes in various physical parameters (e.g. sea ice cover, clouds, heat transport and surface fluxes) affect the temperature response. Using a process-oriented decomposition of the simulate Arctic surface energy budget, we attribute the largest contribution to the CMIP5 intermodel spead in projected Arctic warming to the Barents-Kara Sea region. Our results reveal that the increasing seasonal fluxing of ocean heat content is a significant part of the intermodel spread in AA and relates strongly to change in surface turbulent fluxes. Our results indicate that if we are to significantly reduce the intermodel spread in projected AA we must focus on understanding the behavior and physical processes that drive surface energy flows in the B-K sea region.

Patrick Taylor↗
NASA NTRS1994

Extreme ultraviolet spectrum of a solar active region from SERTS

We present wavelengths and absolute intensities for 243 emission lines from a single active region observed by the Solar Extreme Ultraviolet (EUV) Rocket Telescope and Spectrograph (SERTS) on 1989 May 5. For this catalog, the imaged spectra have been spatially averaged over a field of view 7 sec x 276 sec cutting through the center of AR5464 at S18 W45. Wavelength coverage is 170-450 A with a spectral resolution approaching 10,000. Most of the line positions are determined to 5 mA or better, representing the highest accuracy yet obtained for solar wavelengths throughout this spectral interval. The relative photometric calibration of the instrument is good to +/- 20% over its first-order range, and has been placed onto an absolute scale that should be correct to within a factor less than 2. Where known, identifications, atomic transitions and formation temperatures are also given. The identified lines arise from temperatures that cover the range log T greater than or equal to 4.7 and less than or equal to 6.8, providing information about the Sun's corona and upper transition region. Upper limits to the intensity of any emission line not included here can be estimated from the measured instrumental sensitivity. This averaged EUV spectrum should prove useful as a source of accurate wavelengths and intensities for emission characteristic of the high-temperature plasma associated with a solar active region and small subflare.

Thomas, Roger J.↗
DOE OSTI2024

Comparison of Machine Learning-Based Predictive Models of the Nutrient Loads Delivered from the Mississippi/Atchafalaya River Basin to the Gulf of Mexico

Predicting nutrient loads is essential to understanding and managing one of the environmental issues faced by the northern Gulf of Mexico hypoxic zone, which poses a severe threat to the Gulf’s healthy ecosystem and economy. The development of hypoxia in the Gulf of Mexico is strongly associated with the eutrophication process initiated by excessive nutrient loads. Due to the complexities in the excessive nutrient loads to the Gulf of Mexico, it is challenging to understand and predict the underlying temporal variation of nutrient loads. The study was aimed at identifying an optimal predictive machine learning model to capture and predict nonlinear behavior of the nutrient loads delivered from the Mississippi/Atchafalaya River Basin (MARB) to the Gulf of Mexico. For this purpose, monthly nutrient loads (N and P) in tons were collected from US Geological Survey (USGS) monitoring station 07373420 from 1980 to 2020. Machine learning models—including autoregressive integrated moving average (ARIMA), gaussian process regression (GPR), single-layer multilayer perceptron (MLP), and a long short-term memory (LSTM) with the single hidden layer—were developed to predict the monthly nutrient loads, and model performances were evaluated by standard assessment metrics—Root Mean Square Error (RMSE) and Correlation Coefficient (R). The residuals of predictive models were examined by the Durbin–Watson statistic. The results showed that MLP and LSTM persistently achieved better accuracy in predicting monthly TN and TP loads compared to GPR and ARIMA. In addition, GPR models achieved slightly better test RMSE score than ARIMA models while their correlation coefficients are much lower than ARIMA models. Moreover, MLP performed slightly better than LSTM in predicting monthly TP loads while LSTM slightly outperformed for TN loads. Furthermore, it was found that the optimizer and number of inputs didn’t show effects on the LSTM performance while they exhibited impacts on MLP outcomes. This study explores the capability of machine learning models to accurately predict nonlinearly fluctuating nutrient loads delivered to the Gulf of Mexico. Further efforts focus on improving the accuracy of forecasting using hybrid models which combine several machine learning models with superior predictive performance for nutrient fluxes throughout the MARB.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Clear-sky detection for PV degradation analysis using multiple regression

A method is presented to detect clear-sky periods for plane-of-array irradiance time-averaged data that is based on the algorithm originally described by Reno and Hansen. Here we show this new method improves the state-of-the-art by providing accurate detection at longer data averaging intervals. Moreover, our new method detects clear periods in plane-of-array data, which is novel. The new method is developed by applying a Design of Experiment approach to optimize the parameters used in the Reno method, and Monte Carlo simulations are used to understand the robustness of the found parameters. Clear-sky detection accuracy is compared among four methods: the Reno method, the default clear-sky filter in RdTools, the Ellis method, and the method outlined in this work, using a hand-labeled two-year data set of 1-min plane-of-array irradiance for a fixed tilt system. The RdTools clear-sky filter is marred by excessive false positives. The other methods all perform well at 1-min data intervals; the method developed here provides more accurate detection at longer data averaging intervals. We show that the parameters are directly linked to the data frequency in the hope that these input variables may not have to be optimized for every data frequency and location. However, only a single fixed system in one location was carefully examined. Finally, we illustrate how accurate determination of clear-sky conditions helps to eliminate data noise and bias in the assessment of long-term performance of PV plants.

14 SOLAR ENERGY↗
DOE OSTI2021

Early season prediction of within-field crop yield variability by assimilating CubeSat data into a crop model

Accurate early season predictions of crop yield at the within-field scale can be used to address a range of crop production, management, and precision agricultural challenges. While the remote sensing of within-field insights has been a research goal for many years, it is only recently that observations with the required spatio-temporal resolutions, together with efficient assimilation methods to integrate these into modeling frameworks, have become available to advance yield prediction efforts. Here we explore a yield prediction approach that combines daily high-resolution CubeSat imagery with the APSIM crop model. The approach employs APSIM to train a linear regression that relates simulated yield to simulated leaf area index (LAI). That relationship is then used to identify the optimal regression date at which the LAI provides the best prediction of yield: in this case, approximately 14 weeks prior to harvest. Instead of applying the regression on satellite imagery that is coincident, or closest to, the regression date, our method implements a particle filter that integrates CubeSat-based LAI into APSIM to provide end-of-season high-resolution (3 m) yield maps weeks before the optimal regression date. The approach is demonstrated on a rainfed maize field located in Nebraska, USA, where suitable collections of both imagery and in-situ data were available for assessment. The procedure does not require in-field data to calibrate the regression model, with results showing that even with a single assimilation step, it is possible to provide yield estimates with good accuracy up to 21 days before the optimal regression date. Yield spatial variability was reproduced reasonably well, with a strong correlation to independently collected measurements (R 2 = 0.73 and rRMSE = 12%). When the field averaged yield was compared, our approach reduced yield prediction error from 1 Mg/ha (control case based on a calibrated APSIM model), to 0.5 Mg/ha (using satellite imagery alone), and then to 0.2 Mg/ha (results with assimilation up to three weeks prior to the optimal regression date). Such a capacity to provide spatially explicit yield predictions early in the season has considerable potential to enhance digital agricultural goals and improve end-of-season yield predictions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

On the measurement of shape: With applications to lunar regolith

With the renewed commitment from NASA and other commercial entities for a presence on the Moon, the importance of understanding the characteristics of lunar regolith and how to utilize it have become the target of increasing scrutiny. Much of what is known about lunar regolith was collected during and immediately after the Apollo program, however, analytical techniques and instrumentation have advanced in leaps and bounds in the subsequent decades. Specifically, dynamic image analysis systems have advanced to the point that millions of particles can have morphological characteristics automatically determined in relatively short time frames. Particle morphological data was collected on several lunar samples and a pair of widely used regolith simulants to ascertain the accuracy of these simulants and to explore statistical analysis methods of these large datasets. It is found that these morphology datasets can vary widely depending on the particle size of the particles, and simple averaging of the data skews the results heavily towards the numerically abundant size ranges, the fines. Different reporting methods are suggested to ameliorate these problems. When applied to the lunar regolith, the particles are noted to be less morphologically complex than initially suspected. Compared to the lunar material, the simulants are found to contain some more morphological variability and angular grains. Such difference is likely due to the wildly different comminution processes that these different powder systems are subjected to.

2D shape↗
DOE OSTI2023

Evaluation of electron lifetime for Te inclusions free CdZnTe

Te secondary phase defects are known as major obstacle for improving charge carriers transport properties of CdTe compounds material. The enhanced detector performance was reported for Te inclusions free CZT detector implemented through two-step annealing (i.e., first in Cd and second in Te). Here, we applied the time-of-flight (TOF) technique to measure the electron lifetime in as-grown and two-step annealed CZT material. TOF has several advantages over Hecht equation fitting such as independence of the electric field distribution, direct measurement of carrier lifetime, and high accuracy for high mobility-lifetime product CZT material. The detector performance improved drastically for the two-step annealed CZT detector except which containing inordinate number and size of prismatic punching defects. The average electron lifetime increased more than 10 times after successful two-step annealing.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Global fire modelling and control attributions based on the ensemble machine learning and satellite observations

Contemporary fire dynamics is one of the most complex and least understood land surface phenomena. Global fire controls related to climate, vegetation, and anthropogenic activity are usually intertwined, and difficult to disentangle in a quantitative way. Here, we leveraged an ensemble of five machine learning (ML) models and multiple satellite-based observations to conduct global fire modeling for three fire metrics (burned area, fire number, and fire size), and quantified driving mechanisms underlying annual fire changes in a spatially resolved manner for the period 2003–2019. Ensemble learning is a meta-approach that combines multiple ML predictions to improve accuracy, robustness, and generalization performance. We found that the optimized ensemble ML well reproduced annual dynamics of global burned area (R 2 = 0.90, P < 0.001), total fire numbers (R 2 = 0.86, P < 0.001), and averaged fire size (R 2 = 0.70, P < 0.001). Additionally, the ensemble ML captured key spatial patterns of multi-year mean magnitudes, annual variabilities, anomalies, and trends for different fire metrics. Our ML-based fire attributions further highlighted the dominant role of enhanced anthropogenic activity in reducing global burned area (–1.9 Mha/yr, P < 0.01), followed by climate control (–1.3 Mha/yr, P < 0.01) and insignificant positive vegetation control (0.4 Mha/yr, P = 0.60). Spatially, climate dominated a much larger burned area (53.7%) than human (23.4%) or vegetation control (22.9%); however, the counteracting effects from regional wetting and drying trends weakened the net climate impacts on global burned area. The fire number and fire size exhibited similar spatial control patterns with burned area; globally, however, fire number tended to be more affected by climate while fire size more influenced by human activities. Overall, our study confirmed the feasibility and efficiency of ensemble ML in global fire modeling and subsequent control attributions, providing a better understanding of contemporary fire regimes and contributing to robust fire projections in a changing environment.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Isotopic analysis of Nd nanoparticles using single particle MC-ICP-MS: A comparative study with single particle-ICP-TOF-MS

Single particle - inductively coupled plasma - mass spectrometry (SP-ICP-MS) is a powerful technique for characterization of the elemental and isotopic composition of individual particles. In this work, the capabilities of the newest generation of MC-ICP-MS with acquisition rates down to 50 ms were evaluated for single particle analysis, with a focus on isotopic precision achievable on a single-particle level. Nd (NdVO 4 ) nanoparticles (~120 nm in diameter) were used as case study and were first characterized in terms of mass (respective size) and particle number concentration by SP-ICP-TOF-MS and then by SP-MC-ICP-MS for isotopic precision. For the isotopic ratio measurements, the MC-ICP-MS performance was compared to the ICP-TOF-MS and it was found that the isotope ratio precision was increased (R 2 between 0.98 and 0.99) compared to ICP-TOF-MS (R 2 between 0.88 and 0.97). The accuracy attained on a single particle level, was compared to bulk digestion followed by MC-ICP-MS analysis, and the SP-MC-ICP-MS technique was able to determine the particle population average to be <4 %, percent relative differences for the 142 Nd/ 144 Nd, 143 Nd/ 144 Nd, 145 Nd/ 144 Nd, 146 Nd/ 144 Nd, and 148 Nd/ 144 Nd ratios The detection limit for the SP-MC-ICP-MS approach was also assessed. Here, when utilizing an all Faraday-cup based detection scheme the determined LOD for the measurements was 0.2fg for Nd, per particle. Based on these results, the newest generation of MC-ICP-MS has demonstrated its utility for performing SP measurement, particularly when high precision isotopic determination is warranted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Optimized Quantum Program Execution Ordering to Mitigate Errors in Simulations of Quantum Systems

Simulating the time evolution of a physical system at quantum mechanical levels of detail - known as Hamiltonian Simulation (HS) - is an important and interesting problem across physics and chemistry. For this task, algorithms that run on quantum computers are known to be exponentially faster than classical algorithms; in fact, this application motivated Feynman to propose the construction of quantum computers. Nonetheless, there are challenges in reaching this performance potential. Prior work has focused on compiling circuits (quantum programs) for HS with the goal of maximizing either accuracy or gate cancellation. Our work proposes a compilation strategy that simultaneously advances both goals. At a high level, we use classical optimizations such as graph coloring and travelling salesperson to order the execution of quantum programs. Specifically, we group together mutually commuting terms in the Hamiltonian (a matrix characterizing the quantum mechanical system) to improve the accuracy of the simulation. We then rearrange the terms within each group to maximize gate cancellation in the final quantum circuit. Furthermore, these optimizations work together to improve HS performance and result in an average 40% reduction in circuit depth. This work advances the frontier of HS which in turn can advance physical and chemical modeling in both basic and applied sciences.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Data associated with “Different methods of estimating riverbed sediment grain size diverge at the basin scale ” (v2)

This data package is associated with the publication “Different methods of estimating riverbed sediment grain size diverge at the basin scale” published in Frontiers in Earth Science (Regier et al., 2025). The distribution of sediment grain size in streams and rivers is often quantified by the median grain size (d50), a key metric for understanding and predicting hydrologic and biogeochemical function of streams and rivers. Manual methods to measure d50 are time-consuming and ignore larger grains, while model-based methods to estimate d50 often over-generalize basin characteristics, and therefore cannot accurately represent site-scale heterogeneity. Here, we apply a machine learning-enabled photogrammetry methodology (You Only Look Once, or YOLO) for estimating d50 for grains > 2 mm based on images collected from streams and rivers throughout the Yakima River Basin (YRB). To understand how such methods may help bridge the gaps in resolution and accuracy between manual and catchment characteristics model-based d50 estimates, we compared YOLO d50 values to manual and model-based estimates across the YRB. We found distinct differences among methods for d50 averages and variability, and relationships between d50 estimates and basin characteristics. Source images can be found at https://data.ess-dive.lbl.gov/view/doi:10.15485/1892052. This data package was originally published in May 2023. It was updated August 2025 (v2; new and modified files). File and folder names were not revised to indicate changes. See the change history section in the readme for more details. In addition to the readme, this data package also includes a file-level metadata (FLMD) file that describes each file and a data dictionary (DD) that describes all column/row headers and variable definitions. This dataset is comprised of one main data folder containing (1) file-level metadata; (2) data dictionary; (3) readme; (4) and subfolders containing data, figures, and scripts. The data folder contains datasets used for the analyses in the manuscript in image, text-delimited or geospatially-referenced formats. The figures folder contains the figures from the manuscript in different formats. The scripts folder contains all of the scripts used to complete the analyses in the manuscript. All files are .csv, .rds, .dbf, .prj, .shp, .shx, .jpg, .png, .R, .Rproj, or .pdf. We acknowledge the Yakama Nation as owners and caretakers of the lands where we collected some of these data. We thank the Confederated Tribes and Bands of the Yakama Nation Tribal Council and Yakama Nation Fisheries for working with us to facilitate sample collection and optimization of data usage according to their values and worldview.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Evaluation of a quasi-steady-state approximation of the cloud droplet growth equation (QDGE) scheme for aerosol activation in global models using multiple aircraft data over both continental and marine environments

This research introduces a numerically efficient aerosol activation scheme and evaluates it by using stratus and stratocumulus cloud data sampled during multiple aircraft campaigns in Canada, Chile, Brazil, and China. The scheme employs a quasi-steady-state approximation of the cloud droplet growth equation (QDGE) to efficiently simulate aerosol activation, the vertical profile of supersaturation, and the activated cloud droplet number concentration (CDNC) near the cloud base. The calculated maximum supersaturation values using the QDGE scheme were compared with multiple parcel model simulations under various aerosol and environmental conditions. The differences are all below 0.18 %, indicating good performance and accuracy of the QDGE scheme. We evaluated the QDGE scheme by specifying observed environmental thermodynamic variables and aerosol information from 31 cloud cases as input and comparing the simulated CDNC with cloud observations. The average of mean relative error ($\overline{MRE}$) of the simulated CDNC for cloud cases in each campaign ranges from 17.30 % in Brazil to 25.90 % in China, indicating that the QDGE scheme successfully reproduces observed variations in CDNC over a wide range of different meteorological conditions and aerosol regimes. Additionally, we carried out an error analysis by calculating the maximum information coefficient (MIC) between the MRE and input variables for the individual campaigns and all cloud cases. MIC values were then sorted by aerosol properties, pollution level, environmental humidity, and dynamic condition according to their relative importance to MRE. Based on the error analysis, we found that the magnitude of MRE is more relevant to the specification of input aerosol pollution level in marine regions and aerosol hygroscopicity in continental regions than to other variables in the simulation.

54 ENVIRONMENTAL SCIENCES↗