Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind potential”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Elimination of Potential Electrical Stress During EMC (CS01) Testing

This viewgraph presentation reviews possible ways to eliminate electrical stress during Electromagneticic Compatibility (EMC) testing. The presentation reviews tests that have had problems due to electrical stress. On December 5, 1995 Cassini Radar instrument failed a functional test in preparation for EMC conducted susceptibility (CSO 1 ) testing. The instrument power supply did not turn on as required, and failure occurred prior to injection of CS test stimulus. A investigation of the failure was conducted. A PSPICE simulation of Cassini Radar 30V line using the EMC test setup was performed; the result of the simulation was an oscillation on the 30V input of the power supply. In another case: on December 28, 1999 an oscillation occurred on the input power line of the SlRTF Infrared Array Camera (IRAC) while preparing to perform CSOI testing, Resulted in damage to flight hardware. Subsequent to failure, JPL provided GSFC history and corrective action from Cassini Radar CSOI test failure GSFC implemented the same corrective action as JPL, except that the value of the resistor connected across the isolation transformer primary winding is 2.5 ohms instead of 50 ohms. Three recommendations are made: (1) Make EMC test community aware of the problem and potential solutions by presenting papers at major environmental test conferences (2) Include warnings and safeguards in EMC test requirements and procedures (3) Try to convince EMC test equipment suppliers to design a CSOl test fixture similar to fixture shown in the diagram

Cassini radar↗
NASA NTRS2009

Wind Turbine Acoustics

Wind turbine generators, ranging in size from a few kilowatts to several megawatts, are producing electricity both singly and in wind power stations that encompass hundreds of machines. Many installations are in uninhabited areas far from established residences, and therefore there are no apparent environmental impacts in terms of noise. There is, however, the potential for situations in which the radiated noise can be heard by residents of adjacent neighborhoods, particularly those neighborhoods with low ambient noise levels. A widely publicized incident of this nature occurred with the operation of the experimental Mod-1 2-MW wind turbine, which is described in detail elsewhere. Pioneering studies which were conducted at the Mod-1 site on the causes and remedies of noise from wind turbines form the foundation of much of the technology described in this chapter.

Hubbard, Harvey H.↗
NASA NTRSDate not supplied

Additively Manufactured Wind Tunnel Balances for Propulsive Force Measurement

Propulsive forces and moments during powered descent are not understood well enough to design an entry, decent, and landing vehicle with high confidence using solely computational fluid dynamics modelling (CFD). Therefore, wind tunnel testing is required to quantify uncertainties in computational modeling and simulation. Wind tunnel balances are structural, high-precision, multi-axis force transducers that provide direct measurement of these aerodynamic forces and moments, however their complex designs make them costly and time consuming to produce and approaches used to manufacture them have not changed significantly since the 1960s. This work demonstrates that additive manufacturing (AM) can be used to manufacture wind tunnel balances with significantly reduced fabrication time and expense. Moreover, the design flexibility afforded by the additive manufacturing process has the potential to enable new capabilities with respect to measuring propulsion forces during entry, decent, and landing testing. Here we present two novel balance designs enabled by AM. One will provide direct measurement of aerodynamic interference forces and moments on powered descent models (retropropulsion forces) to support CFD validation and further development of Mars human landing vehicle concepts. The second design will be used to characterize a reaction control system during entry descent and landing testing over a wide Mach number range.

Wind tunnel balance↗
NASA NTRS1989

Lifting-body option for a Space Station rescue vehicle

With the proposed development of the Space Station Freedom, the need for an assured crew return capability (ACRC) has been identified. During the past 2 years within NASA, there has been an ongoing activity to establish the design requirements for such a vehicle and to identify candidate vehicle concepts that can satisfy these requirements. From this activity, three primary design reference missions and four candidate vehicle concepts have been identified. In support of this activity, the emphasis at Langley has been to assess the potential application of a lifting-body concept derived from work on the HL-10 and X-24 programs in the late sixties. A vehicle systems analysis has been completed including wind-tunnel tests, aerodynamic heating predictions, six-degree-of-freedom entry simulations, and a global landing opportunities assessment. This report summarizes the results of work at Langley over the past 2 years to define the candidate lifting-body ACRC vehicle and provides insight into potential benefits of the higher cross range of this concept in accomplishing the Space Station rescue mission.

Hook, W. Ray↗
NASA NTRS1992

Atmospheric wind sensing with a 1 and 2 micron coherent lidar

The majority of coherent lidar remote sensing performed to date has utilized carbon dioxide gas laser technology at wavelengths of 9 to 11 microns. However, the use of rapidly developing solid state laser technology and the shorter wavelengths offers many potential advantages. These advantages include low mass, small size, long shelf and operating lifetimes, the absence of consumables, and in many cases, increased atmospheric transmission. The shorter wavelengths of solid state lasers allow velocity measurements having better range resolution for equivalent wind velocity resolution. Coherent Technologies, Inc. has developed a 1.06 and 2.1 micron coherent lidar system for remote wind field measurements. This system is described, and some performance data are given.

Huffaker, R. Milton↗
NASA NTRS1987

Procedures for Computing Transonic Flows for Control of Adaptive Wind Tunnels

Numerical methods are developed for control of three dimensional adaptive test sections. The physical properties of the design problem occurring in the external field computation are analyzed, and a design procedure suited for solution of the problem is worked out. To do this, the desired wall shape is determined by stepwise modification of an initial contour. The necessary changes in geometry are determined with the aid of a panel procedure, or, with incident flow near the sonic range, with a transonic small perturbation (TSP) procedure. The designed wall shape, together with the wall deflections set during the tunnel run, are the input to a newly derived one-step formula which immediately yields the adapted wall contour. This is particularly important since the classical iterative adaptation scheme is shown to converge poorly for 3D flows. Experimental results obtained in the adaptive test section with eight flexible walls are presented to demonstrate the potential of the procedure. Finally, a method is described to minimize wall interference in 3D flows by adapting only the top and bottom wind tunnel walls.

Rebstock, Rainer↗
NASA NTRS1989

The abundances of elements and isotopes in the solar wind

Solar wind abundances have now been measured for eleven elements and the isotopes of the noble gases. Aside from solar wind protons and alpha particles, which have been studied extensively since the 1960's, information for heavier elements is limited. Nevertheless, two effects stand out. First is the enrichment of abundances of elements with low first ionization potential (FIP), most likely the combined result of an atom-ion separation process in the upper chromosphere, and a marginal coupling of low-charge-state heavy ions to protons and alphas during the acceleration of the solar wind. Second, there is variability in the solar wind composition over a whole range of time scales. Recent measurements carried out in the earth's magnetosheath during times that included high-speed coronal-hole-associated flows indicate a significantly lower overabundance of low FIP elements. Given the fact that the He/H ratio is remarkably constant in the coronal hole solar wind, this result suggests that both enrichment and variability are reduced in such flows.

Gloeckler, George↗
NASA NTRS1986

A new design concept for indraft wind-tunnel inlets with application to the National Full-Scale Aerodynamics Complex

The present inlet design concept for an indraft wind tunnel, which is especially suited to applications for which a specific test section flwo quality is required with minimum inlet size, employs a cascade or 'vaneset' to control flow at the inlet plane, so that test section total pressure variation is minimized. Potential flow panel methods, together with empirical pressure loss predictions, are used to predict inlet cascade performance. This concept has been used to develop an alternative inlet design for the 80 x 120-ft wind tunnel at NASA Ames Research Center. Experimental results show that a short length/diameter ratio wind tunnel inlet furnishing atmospheric wind isolation and uniform test section flow can be designed.

Ross, J. C.↗
NASA NTRS1986

A new design concept for indraft wind-tunnel inlets with application to the national full-scale aerodynamic complex

The present inlet design concept for an indraft wind tunnel, which is especially suited to applications for which a specific test section flow quality is required with minimum inlet size, employs a cascade or vaneset to control flow at the inlet plane, so that test section total pressure variation is minimized. Potential flow panel methods, together with empirical pressure loss predictions, are used to predict inlet cascade performance. This concept has been used to develop an alternative inlet design for the 80 x 120-ft wind tunnel at NASA Ames Research Center. Experimental results show that a short length/diameter ratio wind tunnel inlet furnishing atmospheric wind isolation and uniform test section flow can be designed.

Ross, James C.↗
NASA NTRS1974

Transonic single-mode flutter and buffet of a low aspect ratio wing having a subsonic airfoil shape

Transonic flutter and buffet results obtained from wind-tunnel tests of a low aspect ratio semispan wing model are presented. The tests were conducted to investigate potential transonic aeroelastic problems of vehicles having subsonic airfoil sections. The model employed NACA 00XX-64 airfoil sections in the streamwise direction and had a 14 deg leading edge sweep angle. Aspect ratio, and average thickness were 4.0, 0.35, and 8 percent, respectively. The model was tested at Mach numbers from 0.6 to 0.95 at angles of attack from 0 deg to 15 deg. Two zero lift flutter conditions were found that involved essentially single normal mode vibrations. With boundary layer trips on the model, flutter occurred in a narrow Mach number range centered at about Mach 0.90. The frequency and motion of this flutter were like that of the first normal mode vibration. With the trips removed flutter occurred at a slightly high Mach number but in a mode strongly resembling that of the second normal mode.

Erickson, L. L.↗
NASA NTRS1976

Magnetic suspension techniques for large scale aerodynamic testing

The potential utility of magnetic suspension techniques is discussed in the context of current efforts towards realistic aerodynamic simulation in wind tunnels. Design parameters are defined and problems of constructing large size facilities identified. A three stage strategy towards realizing a truly large scale magnetic suspension and balance with full research capability is outlined. Stage one, consisting of building and testing a prototype superconductor coil system to establish the feasibility of the concept has been completed successfully and its principal results are briefly described. This proven feasibility of using superconductors for magnetic suspensions, together with the successful demonstration of the cryogenic wind tunnel concept, appear to have opened the way to clean tunnel, high-Re aerodynamic testing. Results of a comparative analysis of scaling of several coil technologies for a specific magnetic suspension configuration, from the prototype size to a size compatible with the projected high Reynolds number cryogenic wind tunnel facility, are discussed in some detail.

Zapata, R. N.↗
NASA NTRS1979

Safety considerations in the design and operation of large wind turbines

The engineering and safety techniques used to assure the reliable and safe operation of large wind turbine generators utilizing the Mod 2 Wind Turbine System Program as an example is described. The techniques involve a careful definition of the wind turbine's natural and operating environments, use of proven structural design criteria and analysis techniques, an evaluation of potential failure modes and hazards, and use of a fail safe and redundant component engineering philosophy. The role of an effective quality assurance program, tailored to specific hardware criticality, and the checkout and validation program developed to assure system integrity are described.

Reilly, D. H.↗
NASA NTRS1979

An energy and potential enstrophy conserving scheme for the shallow water equations

A three-dimensional finite difference scheme for the solution of the shallow water momentum equations which accounts for the conservation of potential enstrophy in the flow of a homogeneous incompressible shallow atmosphere over steep topography as well as for total energy conservation is presented. The scheme is derived to be consistent with a reasonable scheme for potential vorticity advection in a long-term integration for a general flow with divergent mass flux. Numerical comparisons of the characteristics of the present potential enstrophy-conserving scheme with those of a scheme that conserves potential enstrophy only for purely horizontal nondivergent flow are presented which demonstrate the reduction of computational noise in the wind field with the enstrophy-conserving scheme and its convergence even in relatively coarse grids.

Arakawa, A.↗
NASA NTRS1982

Surface flow visualization using indicators

Surface flow visualization using indicators in the cryogenic wind tunnel which requires a fresh look at materials and procedures to accommodate the new test conditions is described. Potential liquid and gaseous indicators are identified. The particular materials illustrate the various requirements an indicator must fulfill. The indicator must respond properly to the flow phenomenon of interest and must be observable. Boundary layer transition is the most important phenomenon for which flow visualization indicators may be employed. The visibility of a particular indicator depends on utilizing various optical or chemical reactions. Gaseous indicators are more difficult to utilize, but because of their diversity may present unusual and useful opportunities. Factors to be considered in selecting an indicator include handling safety, toxicity, potential for contamination of the tunnel, and cost.

Crowder, J. P.↗
NASA NTRS1986

On the potential use of radar-derived information in operational numerical weather prediction

Estimates of requirements likely to be levied on a new observing system for mesoscale meteonology are given. Potential observing systems for mesoscale numerical weather prediction are discussed. Thermodynamic profiler radiometers, infrared radiometer atmospheric sounders, Doppler radar wind profilers and surveillance radar, and moisture profilers are among the instruments described.

Mcpherson, R. D.↗
NASA NTRS1988

Net current measurements and secondary electron emission characteristics of the Voyager plasma science experiment and their impact on data interpretation

The Voyager Plasma Science (PLS) instrument is capable of returning integral (DC) current measurements, similar in some respects to measurements made with a Langmuir probe or a retarding potential analyzer, although there are significant differences. The integral measurements were made during a calibration sequence in the solar wind, during Cruise Science Maneuvers, and within the magnetospheres of Jupiter and Saturn by Voyager 1. After the failure of the PLS experiment following the Saturn encounter, that instrument was placed in the DC return mode returning possibly usable data from early 1981 through early 1985. The DC return measurements are difficult to interpret and are above threshold values only for relatively large fluxes; the determination of the measured current level is dependent on the operating temperature of the preamplifiers which further complicates the interpretation. Nevertheless, these measurements can be used to determine the efficiency of the suppressor grid at preventing the loss of secondary electrons off the collector plate. Some DC return measurements have been invaluable in aiding in the interpretation of some electron plasma measurements not previously understood. It is found that electron spectra can be significantly modified by the presence of second generation secondary electrons produced by either first generation secondaries or photoelectrons on the support ring of the negative high voltage modulator grid within the instrument housing.

Mcnutt, Ralph L., Jr.↗
NASA NTRS1998

The Hadean, Through a Glass Telescopically: Observations of Young Solar Analogs

Investigations into the Earth's surface environment during the Hadean eon (prior to 3.8 Ga) are hampered by the paucity of the geological and geochemical record and the relative inaccessibility of better-preserved surfaces with possibly similar early histories (i.e., Mars). One approach is to observe nearby, young solar-mass stars as analogs to the Hadean Sun and its environment. A catalog of 38 G and early K stars within 25 pc was constructed based on main-sequence status, bolometric luminosity, lack of known stellar companions within 800 AU, and coronal X-ray luminosities commensurate with the higher activity of solar-mass stars <0.8 b.y. old. Spectroscopic data support the assignment of ages of 0.2 - 0.8 Ga for most of these stars. Observations of these objects will provide insight into external forces that influenced Hadean atmosphere, ocean, and surface evolution (and potential ecosystems), including solar luminosity evolution, the flux and spectrum of solar ultraviolet radiation, the intensity of the solar wind, and the intensity and duration of a late period of heavy bombardment. The standard model of solar evolution predicts a luminosity of 0.75 solar luminosity at the end of the Hadean, implying a terrestrial surface temperature inconsistent with the presence of liquid water and motivating atmospheric greenhouse models. An alternative model fo solar evolution that invokes mass loss, constructed to explain solar Li depletion, attenuates or reverses this luminosity evolution of the atmospheres of Earth and the other terrestrial planets. This model can be tested by Li abundance measurements. The continuum emission from stellar wind plasma during significant mass loss may be detectable at millimeter and radio wavelengths. The Earth (and Moon) experienced a period of intense bombardment prior to 3.8 Ga, long after accretion was completed in the inner solar system and possibly associated with the clearing of residual planetesimals in the outer solar system. Such a bombardment may have contributed volatiles and organics to the surface, but also have limited the appearacne of a biosphere. While planetary systems around solar systems cannot be detected directly with present technology, the thermal emission from the interplanetary dust generated during a similar heavy bombardment period can be. Midinfrared observations of a large uniform sample of solar analogs are used to constrain the frequency and duration of such events.

Gaidos, E. J.↗
NASA NTRS2003

First Results of the Expedition to the Highest Lake on Earth: Studying a Martian Paleolake in Bolivia and the Survival Strategies Developed by Living Organisms

Between October 16th and November 9th 2002, the first NASA Ames DDF Licancabur multidisciplinary expedition initiated the investigation of the biology and environment for life in the highest lake on Earth located at the summit of the Licancabur volcano (6017 m/20,056 ft) at the boundary of Chile and Bolivia. The low oxygen, low atmospheric pressure, high-UV radiation, average temperature, volcano-tectonic and hydrothermal environment make the site a close analog to Martian paleolakes 3.5 billion years ago. The overall goal of the project is to understand through a series of high altitude scientific expeditions what strategies life is using to defend itself against killer-level UV radiation and environmental extreme conditions at this altitude. Several other lakes are located at 4300 m at the foot of the Licancabur volcano (hereafter named laguna Blanca and Laguna Verde). They were also investigated using identical experiments and methods as for the summit lake in order to compare the results and better understand the evolution of survival strategies at transitioning elevations. The lagunas are geothermally heated and many springs provide water at various temperatures. Sources of heat are also suspected for the summit lake as its surface water temperature was measured during the successful ascent at +6 C in a -9 C ambient crater environment (with a wind chill factor of -25 C with a wind blowing almost constantly). Results of this project are expected to provide critical keys to help searching and identifying potential sites for life (extant/extinct) on Mars and developing instruments, experiments and technologies for future missions.

Cabrol, N. A.↗