SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Sensitive method, identifying effective damping mechanisms, involves comparing experimentally determined ratio of first to second mode magnification factors related to common point on beam. Cluster size has little effect on frequencies of elements, magnification factor decreases with cluster size, and viscous and stress damping are dominant damping mechanisms.
A semi-empirical scheme for the prediction of transonic pressure distribution on the surface of V/STOL inlets at high incidence angles has been developed. The investigation is intended to improve the boundary layer calculation and separation prediction by including the effects of shock wave-boundary layer interaction into the Lewis Inlet Viscous Computer Program. Wind-tunnel results and theoretical pressure calculation for critical cases are used in constructing the transonic pressure distribution. The program, which describes the development of the boundary layer and predicts the possible flow separation, can handle the cases of inlets at high incidence angles where local supersonic region may occur in the flow.
Progress towards successful modelling of unsteady flows past two-dimensional oscillating airfoils is examined. Linearized, thin airfoil theory is reviewed with special regard to the vortex shedding which occurs when either the body or the flow fluctuates. A sinusoidally oscillating flat-plate airfoil is considered in terms of noncirculatory components, including boundary conditions and bound and wake vortices, respectively. Applications of linear theory to vertical airfoil oscillations and to oscillating control surfaces are described, and oscillating airfoils in subsonic and supersonic flows are investigated. Perturbations in linear solutions are explored for the occurrence of second-order effects, and trailing edge and wake effects. The effects of unsteady transonic flows are broken into nearly inviscid and strongly viscous cases, and analyses of dynamic stall and stall flutter are presented.
Numerical solutions of the interacting laminar boundary layer equations are presented for two symmetric airfoils at zero incidence: the NACA 0012 and the NACA 66 sub 3-108 airfoils. The potential flow was computed using Carlson's code, and viscous interaction was treated following a Hilbert integral scheme due to Veldman. Effects of various grid parameters are studied, and pressure and skin friction distributions are compared at several Reynolds numbers. For the NACA 0012 airfoil, Reynolds number is varied from a value just below separation (R sub N = 3000) to a value for which extensive separation occurs (R sub N = 100,000). For the 66 sub 3-018 airfoil, results are given at intermediate values (R sub N - 10,000 and 40,000). The method fails to converge for greater values of Reynolds number, corresponding to the development of very thin well separated shear layers where transition to turbulence would occur naturally.
A numerical investigation of heat and mass transfer in a dissociated laminar boundary layer of air on an isothermal flat plate is carried out for different degrees of cooling of the wall. A finite-difference chemical model is used to study elementary reactions involving NO2 and N2O. The analysis is based on equations of continuity, momentum, energy, conservation and state for the two-dimensional viscous flow of a reacting multicomponent mixtures. Attention is given to the effects of both catalyticity and noncatalyticity of the wall.
A 3-D Navier-Stokes code has been developed for analysis of turbomachinery blade rows and other internal flows. The Navier-Stokes equations are written in a Cartesian coordinate system rotating about the x-axis, and then mapped to a general body-fitted coordinate system. Streamwise viscous terms are neglected using the thin-layer assumption, and turbulence effects are modeled using the Baldwin-Lomax turbulence model. The equations are discretized using finite differences on stacked C-type grids and are solved using a multistage Runge-Kutta algorithm with a spatially-varying time step and implicit residual smoothing. Calculations have been made of a horseshoe vortex formed in front of a flat plate with a round leading edge standing in a turbulent endwall boundary layer. Comparisons are made with experimental data taken by Eckerle and Langston for a circular cylinder under similar conditions. Computer and measured results are compared in terms of endwall flow visualization pictures and total pressure loss contours and vector plots on the symmetry plane. Calculated details of the primary vortex show excellent agreement with the experimental data. The calculations also show a small secondary vortex not seen experimentally.
A 3-D Navier-Stokes code has been developed for analysis of turbomachinery blade rows and other internal flows. The Navier-Stokes equations are written in a Cartesian coordinate system rotating about the x-axis, and then mapped to a general body-fitted coordinate system. Streamwise viscous terms are neglected using the thin-layer assumption, and turbulence effects are modeled using the Baldwin-Lomax turbulence model. The equations are discretized using finite differences on stacked C-type grids and are solved using a multistage Runge-Kutta algorithm with a spatially-varying time step and implicit residual smoothing. Calculations have been made of a horseshoe vortex formed in front of a flat plate with a round leading edge standing in a turbulent endwall boundary layer. Comparisons are made with experimental data taken by Eckerle and Langston for a circular cylinder under similar conditions. Computer and measured results are compared in terms of endwall flow visualization pictures and total pressure loss contours and vector plots on the symmetry plane. Calculated details of the primary vortex show excellent agreement with the experimental data. The calculations also show a small secondary vortex not seen experimentally.
The flow field in the Purdue Research Centrifugal Compressor is studied using a laser two-focus (L2F) velocimeter. L2F data are obtained which quantify: (1) the compressor inlet flow field; (2) the steady-state velocity field in the impeller blade passages; and (3) the flow field in the radial diffuser. The L2F data are compared with both laser Doppler velocimetry (LDV) data and predictions from three-dimensional inviscid and viscous flow models. In addition, a model is developed to calculate the effect on the measurement volume geometry of refraction by curved windows. Finally, the advantages and disadvantages of using the L2F for turbomachinery measurements is discussed in terms of measurement accuracy, ease of use, including sample time per correlated event and the ability to make measurements in regions of high noise due to stray radiation from wall reflections.
The Van Leer flux splitting is known to produce excessive numerical dissipation for Navier-Stokes calculations. Researchers attempt to remedy this deficiency by introducing a higher order polynomial expansion (HOPE) for the mass flux. In addition to Van Leer's splitting, a term is introduced so that the mass diffusion error vanishes at M equals 0. Several splittings for pressure are proposed and examined. The effectiveness of the HOPE scheme is illustrated for 1-D hypersonic conical viscous flow and 2-D supersonic shock-wave boundary layer interactions. Also, the authors give the weakness of the scheme and suggest areas for further investigation.
The success of NASA's Aeroassisted Flight Experiment project depends on the suitable placement of instrumentation on the vehicle surface and the ability of the vehicle to fly the maximum science payload. The initial aerodynamic data base was established using wind tunnel data and CFD analyses, where the influence of real-gas effects precluded the use of ground-facility data. More recently, a viscous thermochemical nonequilibrium flow analysis about the complete vehicle, including the wake, has updated the vehicle aerodynamic data base.
The Van Leer flux splitting is known to produce excessive numerical dissipation for Navier-Stokes calculations. Researchers attempt to remedy this deficiency by introducing a higher order polynomial expansion (HOPE) for the mass flux. In addition to Van Leer's splitting, a term is introduced so that the mass diffusion error vanishes at M = 0. Several splittings for pressure are proposed and examined. The effectiveness of the HOPE scheme is illustrated for 1-D hypersonic conical viscous flow and 2-D supersonic shock-wave boundary layer interactions.
The period of support of this Cooperative Agreement was from April 15, 1990 to October 31, 1992, with a no-cost extension to October 31, 1993 to complete some unfinished tasks. Within this period, research associate Dr. Kai-Hsiung Kao has made tremendous contributions to this project and has produced an impressive amount of publications. At the early stage of the research, he spent some time on the extension of his doctoral thesis in a subject closely related to the present project. His major research effort was devoted to the investigation of stability of a viscous flow between two differentially rotating cylinders, with an emphasis on the effects of compressibility and heat transfer. Actually, the research topics were not restricted to those described by the title of this Agreement, as reflected in some of the more recent publications.
The design process for developing the natural flow wing design on the HSR arrow wing configuration utilized several design tools and analysis methods. Initial fuselage/wing designs were generated with inviscid analysis and optimization methods in conjunction with the natural flow wing design philosophy. A number of designs were generated, satisfying different system constraints. Of the three natural flow wing designs developed, the NFWAc2 configuration is the design which satisfies the constraints utilized by McDonnell Douglas Aerospace (MDA) in developing a series of optimized configurations; a wind tunnel model of the MDA designed OPT5 configuration was constructed and tested. The present paper is concerned with the viscous analysis and inverse design of the arrow wing configurations, including the effects of the installed diverters/nacelles. Analyses were conducted with OVERFLOW, a Navier-Stokes flow solver for overset grids. Inverse designs were conducted with OVERDISC, which couples OVERFLOW with the CDISC inverse design method. An initial system of overset grids was generated for the OPT5 configuration with installed diverters/nacelles. An automated regridding process was then developed to use the OPT5 component grids to create grids for the natural flow wing designs. The inverse design process was initiated using the NFWAc2 configuration as a starting point, eventually culminating in the NFWAc4 design-for which a wind tunnel model was constructed. Due to the time constraints on the design effort, initial analyses and designs were conducted with a fairly coarse grid; subsequent analyses have been conducted on a refined system of grids. Comparisons of the computational results to experiment are provided at the end of this paper.
Using a high-temperature optically based displacement measurement system, a foil air bearing's stiffness and damping characteristics were experimentally determined. Results were obtained over a range of modified Sommerfeld Number from 1.5E6 to 1.5E7, and at temperatures from 25 to 538 C. An Experimental procedure was developed comparing the error in two curve fitting functions to reveal different modes of physical behavior throughout the operating domain. The maximum change in dimensionless stiffness was 3.0E-2 to 6.5E-2 over the Sommerfeld Number range tested. Stiffness decreased with temperature by as much as a factor of two from 25 to 538 C. Dimensionless damping was a stronger function of Sommerfeld Number ranging from 20 to 300. The temperature effect on damping being more qualitative, showed the damping mechanism shifted from viscous type damping to frictional type as temperature increased.
Boundary layer ingestion is an aeropropulsive concept associated with a propulsion airframe integration technique that integrates viscous aerodynamics into a propulsion system to achieve more efficient flight. The effectiveness of this concept is heavily dependent on how much of the boundary layer is being ingested into the propulsor. Scaling this concept for transonic wind tunnel testing is often plagued with blockage issues and requires a modification to the model dimensions such as fuselage length and diameter and wingspan. To simulate the boundary layer for these modified models requires a manipulation of the boundary layer height to achieve the appropriate ratio of boundary layer to propulsor inlet diameter or height. This paper will focus on 15 different transonic boundary layer manipulators to achieve varying turbulent boundary layer heights for a representative single-aisle transport utilizing Boundary Layer Ingestion.
The paper examines the effect of viscosity in the release adiabat measurements on minerals. The current inversion of pressure-particle velocity data for release from a high-pressure shock state to a pressure-density path usually depends critically upon the assumption that the release process is isentropic. It has been shown that the effective viscosity for geological materials below stresses of 150 GPa must be at least 1000 kg/m/s so that viscous work in the shock state remains small compared to mechanical work recovered upon adiabatic rarefaction. The magnitude of the shear stress in the shock state in minerals and viscosities of engineering materials shocked to pressures below 150 GPa show effective viscosities of about 1000 kg/m/s or less indicating that the conditions for isentropic release of materials from shock states are achieved and that the Riemann integral can be applied to obtain pressure-density states along the release adiabats of minerals.
The least-squares finite element method (LSFEM) based on the velocity-pressure-vorticity formulation is applied to large-scale/three-dimensional steady incompressible Navier-Stokes problems. This method can accommodate equal-order interpolations and results in symmetric, positive definite algebraic system which can be solved effectively by simple iterative methods. The first-order velocity-Bernoulli function-vorticity formulation for incompressible viscous flows is also tested. For three-dimensional cases, an additional compatibility equation, i.e., the divergence of the vorticity vector should be zero, is included to make the first-order system elliptic. The simple substitution of the Newton's method is employed to linearize the partial differential equations, the LSFEM is used to obtain discretized equations, and the system of algebraic equations is solved using the Jacobi preconditioned conjugate gradient method which avoids formation of either element or global matrices (matrix-free) to achieve high efficiency. To show the validity of this scheme for large-scale computation, we give numerical results for 2D driven cavity problem at Re = 10000 with 408 x 400 bilinear elements. The flow in a 3D cavity is calculated at Re = 100, 400, and 1,000 with 50 x 50 x 50 trilinear elements. The Taylor-Goertler-like vortices are observed for Re = 1,000.
The effective elongational viscosity for an oriented fiber assembly of discontinuous fibers suspended in a viscous matrix fluid is developed for a fiber array with variable overlap length of both symmetric and asymmetric geometries. Further, the relation is developed for a power-law matrix fluid with finite yield stress. The developed relations for a Newtonian fluid reveal that the influence of overlap length upon elongational viscosity may be expressed as a polynomial of second order. The results for symmetric and asymmetric geometries are shown to be equivalent. Finally, for the power-law fluid the influence of fiber aspect ratio on elongational viscosity was shown to be of order m + 1, where m is greater than 0 and less than 1, as compared to 2 for the Newtonian fluid, while the effective yield stress was found to be proportional to the fiber aspect ratio and volume fraction.