Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “tailoring”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

High strain rate deformation of aged TRIP Ti-10V-2Fe-3Al (wt.%) examined by in-situ synchrotron X-ray diffraction

Transformation Induced Plasticity (TRIP) is a promising avenue for tailoring the work hardening response of metastable $β$ titanium (Ti) alloys. Here we show that aged TRIP Ti-10V-2Fe-3Al (wt.%) maintains higher elongations and flow stresses as strain rate increases, if phase stability and microstructural characteristics are tuned. Low temperature aging influences the matrix $β$ phase stability by $ω$ phase precipitation, which affords a promising way to impact the TRIP effect and obtain desirable mechanical properties, ranging from high damping capacity to good strength/ductility combinations. Although TRIP is active during quasi-static and dynamic testing up to 2000 s –1 , increasing aging time and/or strain rate reduces the overall propensity for the TRIP effect and extent of transformation, which occurs rapidly just at the onset of yielding. Importantly, TRIP with $ω$ phase precipitation provides interesting alloying, microstructure, and property design strategies for engineering applications like lightweight protective structures, where high strains and the need for energy absorption are encountered.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Theory-guided design of duplex-phase multi-principal-element alloys

Density-functional theory (DFT) is used to identify phase-equilibria in multi-principal-element and high-entropy alloys (MPEAs/HEAs), including duplex-phase and eutectic microstructures. Here, a combination of composition-dependent formation energy and electronic-structure-based ordering parameters were used to identify a transition from FCC to BCC favoring mixtures, and these predictions experimentally validated in the Al-Co-Cr-Cu-Fe-Ni system. A sharp crossover in lattice structure and dual-phase stability as a function of composition were predicted via DFT and validated experimentally. The impact of solidification kinetics and thermodynamic stability was explored experimentally using a range of techniques, from slow (castings) to rapid (laser remelting), which showed a decoupling of phase fraction from thermal history, i.e., phase fraction was found to be solidification rate-independent, enabling tuning of a multi-modal cell and grain size ranging from nanoscale through macroscale. Strength and ductility tradeoffs for select processing parameters were investigated via uniaxial tension and small-punch testing on specimens manufactured via powder-based additive manufacturing (directed-energy deposition). This work establishes a pathway for design and optimization of next-generation multiphase superalloys via tailoring of structural and chemical ordering in concentrated solid solutions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Alloying Effects on the Transport Properties of Refractory High-entropy Alloys

Additive Manufacturing (AM) has opened new frontiers for the design of refractory high-entropy alloys (HEAs) for high-temperature applications. The thermal conductivity of the AM feedstock is among the most important thermo-physical properties that control the melting and solidification process. Despite its significance, there remains a notable gap in both computational and experimental research concerning the thermal conductivity of HEAs. Here, we use density functional theory (DFT) to systematically investigate the alloying effects on the transport properties of Ti-Cr-Mo-W-V-Nb-Ta RHEAs, including electrical and thermal conductivities and Seebeck coefficient. The relaxation time of charge carriers is a key underlying parameter determining thermal conductivity that is exceedingly challenging to predict from first principles alone, and we thus follow the approach by Mukherjee, Satsangi, and Singh [Chem Mater 32, 6507 (2022)] to optimize the relaxation time for RHEAs. Here we validated thermal conductivity predictions on elemental solids, binary and ternary alloys, and RHEAs and compared them against thermodynamic (CALPHAD) predictions and our experiments with good correlations. To understand observed trends in thermal conductivity, we assessed the phase stability, electronic structure, phonon, and intrinsic- and tensile strength of down-selected RHEAs. Our electronic structure and phonon results connect well with the observed compositional trends for thermal transport in RHEAs. Our DFT assessment and CALPHAD predictions provide a unique design guide for RHEAs with tailored thermal conductivity, a critical consideration for AM and thermal-management applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Driving rapid atomic order in MnAl via low-magnitude magnetic field annealing

Application of a mild (60 mT), uniform magnetic field during short-term thermal treatment of kinetically retained, atomically disordered (paramagnetic) ε-MnAl was found to deliver a significant ~50 % increase in the formation of L1 0 atomically ordered (ferromagnetic) τ-MnAl product phase, compared to that produced by conventional (i.e., zero-field) annealing under identical thermal conditions. The magnetic field, applied in a passive closed-circuit configuration during annealing, induced significant changes in the structural, magnetic, and phase evolution of the material. Computational results based on electronic structure calculations demonstrate that the effective magnetic susceptibility of τ-MnAl is sensitive to the orientation, rather than the magnitude, of an applied magnetic field in the vicinity of the Curie temperature. The uniaxial magnetocrystalline anisotropy of the L1 0 structure is proposed to act as a filter for selective propagation of the population of τ-MnAl variants that are favorably aligned with the applied field. In this manner, crystallographic “gridlock” is alleviated that would otherwise arise from the coexistence of multiple, energetically equivalent τ-phase variants within the parent ε-phase matrix. These results confirm that static, low-magnitude magnetic field annealing is able to accelerate L1 0 atomic ordering in the MnAl system and likely can exert similar influences in relevant magnetic systems, facilitating efficient tailoring of structure-sensitive magnetic properties for the manufacture of magnetic materials.

36 MATERIALS SCIENCE↗
DOE OSTI2026

High temperature stabilization of ultrafine grain tungsten alloys through synergistic compositional complexities

Thermally-stabilized fine-grained microstructures in tungsten provide a pathway to harnessing enhanced properties such as a reduced ductile-to-brittle transition temperature and improved strength while mitigating the adverse effects of grain growth and recrystallization. Here, in this study, we employ a material design strategy that relies on grain boundary segregation in the nanocrystalline state driven by alloy thermodynamics balanced with impurity scavenging through in situ formation of kinetically-stabilizing metal carbides. A W-Ti-Cr alloy is designed through lattice Monte Carlo methods and subsequently synthesized in a single-phase nanocrystalline state, which upon annealing, evolves into an ultrafine grained microstructure containing chromium grain boundary segregation collectively with a dispersed TiX (X=C,O) phase through the reaction of titanium with carbon and oxygen impurities. In situ synchrotron X-ray diffraction experiments demonstrate that increased Ti promotes stabilization across a larger temperature range but with diminishing returns above 10 at.% Ti. Long-term stability was confirmed through the retention of the ultrafine grained microstructure for a total of 8 days (192 h) at 1300 °C without grain/carbide growth and/or recrystallization. Our results demonstrate that, through strategic tailoring of composition and microstructure, one can harness the benefits of both thermodynamic and kinetic stabilization mechanisms, opening pathways for future alloy formulations that expand the window of stability.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multiscale mechanical design of the lightweight, stiff, and damage-tolerant cuttlebone: A computational study

Cuttlebone, the endoskeleton of cuttlefish, offers an intriguing biological structural model for designing low-density cellular ceramics with high stiffness and damage tolerance. Cuttlebone is highly porous (porosity ~93%) and lightweight (density less than 20% of seawater), constructed mainly by brittle aragonite (95 wt%), but capable of sustaining hydrostatic water pressures over 20 atmospheres and exhibits energy absorption capability under compression comparable to many metallic foams (~4.4 kJ/kg). Here, in this work, we computationally investigate how such remarkable mechanical efficiency is enabled by the multiscale structure of cuttlebone. Using the common cuttlefish, Sepia Officinalis, as a model system, we first conducted high-resolution synchrotron micro-computed tomography (µ-CT) and quantified the cuttlebone's multiscale geometry, including the 3D asymmetric shape of individual walls, the wall assembly patterns, and the long-range structural gradient of walls across the entire cuttlebone (ca. 38 chambers). The acquired 3D structural information enables systematic finite-element simulations, which further reveal the multiscale mechanical design of cuttlebone: at the wall level, wall asymmetry provides optimized energy absorption while maintaining high structural stiffness; at the chamber level, variation of walls (number, pattern, and waviness amplitude) contributes to progressive damage; at the entire skeletal level, the gradient of chamber heights tailors the local mechanical anisotropy of the cuttlebone for reduced stress concentration. Our results provide integrated insights into understanding the cuttlebone's multiscale mechanical design and provide useful knowledge for the designs of lightweight cellular ceramics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A novel additive manufacturing compression overmolding process for hybrid metal polymer composite structures

Metal polymer composites combining low density, high strength composites with highly ductile and tough metals have gained traction over the last few decades as lightweight and high-performance materials for industrial applications. However, the mechanical properties are limited by the interfacial bonding strength between metals and polymers achieved through adhesives, welding, and surface treatment processes. In this paper, a novel manufacturing process combining additive manufacturing and compression molding to obtain hybrid metal polymer composites with enhanced mechanical properties is presented. Additive manufacturing enabled deposition of polymeric material with fibers in a predetermined pattern to form tailored charge or preform for compression molding. Here, a grade 300 maraging steel triangular lattice is first fabricated using AddUp FormUp350 laser powder bed system and compression overmolded with additively manufactured long carbon fiber-reinforced polyamide-6,6 (40% wt. CF/PA66) preform. The fabricated hybrid metal polymer composites showed high stiffness and tensile strength. The stiffness and failure characteristics determined from the uniaxial tensile tests were correlated to a finite element model within 20% deviation. Fractographic analyses was performed using microscopy to investigate failure mechanisms of the hybrid structures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure-sensitive mechanical behavior of an additively manufactured psuedoelastic shape memory alloy

The additive manufacturing of shape memory alloys into complex geometries enables fabrication of advanced functional systems across a variety of fields and domains. This work presents results focused on the mechanical behavior of additively manufactured shape memory pseudoelastic NiTi. The deformation induced solid state phase transformation from austenite to martensite allows this system to accommodate large recoverable strains. This deformation behavior is fundamentally driven by crystal-scale transformation physics. Laser powder bed fusion processing reveals that the resulting microstructure, both grain morphology and crystallographic texture, is strongly dependent on the manufacturing processing history. Exhaustive mechanical testing demonstrates that these microstructural factors strongly impact both tensile and cyclic stress–strain behavior. Cyclic dissipative behavior, however, is similar across all tested microstructures following an initial transient period. Remarkably, analysis of spatial strain fields during tensile loading reveals two distinctly different localization “modes”. The first is initiation of localized deformation bands which continuously propagate through the tensile bar during loading. In the second mode localization is observed but lacks propagation; instead additional localization cites nucleate during subsequent loading. The latter phenomena is suspected to be driven by grain-scale deformation physics as the localized band morphologies coincide with grain morphologies. These phenomena strongly impact the resulting aggregate stress–strain behavior. Hence, manufacturers and designers of psuedoelastic functional components must at the very least consider the potential variability in properties when considering additive manufacturing processing. More ideally the process–structure–property relations can be used to further tailor and optimize final functional performance.

Additive manufacturing↗
DOE OSTI2020

An additive manufacturing design approach to achieving high strength and ductility in traditionally brittle alloys via laser powder bed fusion

Additive Manufacturing (AM) presents unprecedented opportunities to enable design freedom in parts that are unachievable via conventional manufacturing. However, AM-processed components generally lack the necessary performance metrics for widespread commercial adoption. We present a novel AM processing and design approach using removable heat sink artifacts to tailor the mechanical properties of traditionally low strength and low ductility alloys. The design approach is demonstrated with the Fe-50 at.% Co alloy, as a model material of interest for electromagnetic applications. AM-processed components exhibited unprecedented performance, with a 300 % increase in strength and an order-of-magnitude improvement in ductility relative to conventional wrought material. These results are discussed in the context of product performance, production yield, and manufacturing implications toward enabling the design and processing of high-performance, next-generation components, and alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High Speed In-situ X-ray Imaging of 3D Freeze Printing of Aerogels

3D freeze printing (3DFP) combines drop-on-demand (DOD) inkjet printing with freeze casting to fabricate lightweight and multifunctional aerogels with customized geometries. Freeze casting is an efficient and easily implemented method capable of fabricating porous, sponge-like structures for many different applications. This process enables tailoring the microstructure of the final product (i.e., pore morphology, alignment, average size distribution, etc.) by controlling the fabrication conditions and freezing kinetics. Furthermore, its combination with DOD printing provides the capability of engineering the macrostructure without relying on a mold as reported for 3D freeze-printed aerogels made from graphene, silver nanowires, and other nanocomposites. In this paper, we performed in-situ X-ray imaging to understand the inside process dynamics in 3DFP using a commercially available colloidal silica ink. We investigated the 3DFP process with the following hierarchy: first, single droplets; then, uniform lines obtained from coalescence of droplets; and finally, three consecutive lines deposited layer by layer. With the help of X-ray imaging, the importance of the balance between material deposition and freezing rates was shown in-situ by the observation inside of the freeze front following the tip of the printed line. The effects of the substrate temperature on the elimination of undesired interfacial boundaries were also shown by the observed ice crystals penetrating from lower to upper layer.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mica filled polyetherketoneketones for material extrusion 3D printing

Polyetherketoneketone (PEKK) has superior physical properties to most available thermoplastics compatible with material extrusion-based 3D printing, including analogs in the polyaryletherketone (PAEK) family. To date, the performance of fused filament fabrication (FFF) compatible PEKK has been detailed primarily as a function of varying the isomer ratios composing the co-polymer structure. The strategy to form blends or composites with PEKK for FFF is attractive for further tailoring of performance in application, yet has received limited attention. Here, we report the integration of three grades of mica platelets into PEKK at 10% and 30% mass loadings to generate an array of filament feedstocks that were then used to print objects with a simple FFF machine. The effects of mica coating chemistry and surface treatment on the compatibility with PEKK and resulting properties are described. Mica fillers at both loadings have only subtle influence on the FFF relevant melt rheological properties inherent to PEKK. Pigment micas at high loadings can lower the melting temperature of PEKK (up to 19 ºC) without shifting its glass transition temperature and inhibit much of the undesirable crystallization occurring during processing with unfilled PEKK. The printed composites were effectively cold crystallized post-printing, affording crystalline fractions up to 90% relative to unfilled PEKK with increased dimensional stabilities. All micas, when used as fillers in low and high relative PEKK crystallinities, significantly increased the tensile modulus (as high as 126% or to 7.31 GPa) of parts in correlation to the loading. Furthermore, the underlying microstructural features of a printed composite were compared to unfilled PEKK by use of a high-resolution helical micro-computed tomography instrument. Practically, pigment micas can confer a wide range of rich colors to 3D-printed PEKK.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Structural stability of thin overhanging walls during material extrusion additive manufacturing of thermoset-based ink

Recent developments have enabled material extrusion additive manufacturing of thermoset-based composite inks on the large scale. In addition, printing out-of-plane components is of broad interest to the polymer material extrusion community. Here, we address some of the challenges associated with both large-scale and out-of-plane thermoset material extrusion additive manufacturing by studying the height at which thin overhanging walls collapse. Walls at a range of overhang angles were printed until they collapsed. An optical camera captured the profile of each wall throughout the print, allowing the collapse height to be identified and the geometric fidelity to the programmed angle to be evaluated. Using previously measured rheological properties, predictive models were generated to approximate the collapse height and profile of the deflected walls. First, an analytical model was created to predict the height at which the walls would yield. The analytical model assumes the walls exhibit a perfectly linear profile; however, experiments proved this assumption to be false. Therefore, a finite element simulation was developed to account for the elastic deflection that occurs during printing. The finite element simulation predicts both the yield height and the deflected profile after the deposition of each layer. For the properties of the thermoset ink used here, the yield height predicted by the analytical model and finite element simulation are virtually identical. These predictions match experimental data reasonably well, but minor errors are observed. Accounting for the fully plastic moment appears to explain the small mismatch between experimental data and predictions. Additionally, the finite element simulation provides an excellent prediction of the deflected profile before the wall begins to collapse. Finally, by demonstrating that the collapse height and deflected profile of thin overhanging walls can be predicted, this work illustrates how the soft viscoelastic properties of thermoset-based composite inks limit the scale of a key feature required to print some nonplanar components. It also provides a basis to tailor in-process curing systems to suppress deflection and collapse of thin overhanging walls.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive manufacturing enabled synergetic strengthening of bimodal reinforcing particles for aluminum matrix composites

An additive manufactured TiB 2 /Al-Cu-Mg-Ni composite with a minor amount of Sc was fabricated by laser powder bed fusion (LPBF). The composite shows a yield strength of ~370 MPa, almost doubling the strength of its wrought matrix counterpart, and an elongation of ~7 %. The superior mechanical properties are attributed to a unique micro-nano hierarchical microstructure, consisting of nanoscale and microscale TiB 2 particles dispersed in a matrix of fine aluminum grains (3 µm) together with intragranular intermetallic nanoparticles and nano-cellular networks (cell size 30 nm). The formation of the TiB 2 nanoparticles is the consequence of partial dissolution of the TiB 2 particulates and the enrichment of Sc in the newly formed nanoparticles. Remarkable strengthening effects are achieved by the bimodal TiB 2 particles, intermetallic nanoparticles and intragranular nano-cellular networks. Finally, this study provides new insights into the role of additive manufacturing in tailoring the microstructure of particulate reinforced metal matrix composites (MMCs) with advanced properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

New insights into the mechanism of ultrasonic atomization for the production of metal powders in additive manufacturing

Ultrasonic atomization is one of the promising technologies for producing metal powders for additive manufacturing, where precise control of particle size and morphology is essential. In this study, we coupled an ultrasonic transducer with a carbon fiber plate and atomized liquid droplets and films under different vibration amplitudes. Water, glycerol, and pure aluminum melt were used to study the atomization mechanism and the resulting droplet/powder characteristics, respectively. High-speed optical and ultrafast synchrotron X-ray imaging were used to study in situ the ultrasonic atomization dynamics, including pulsation and clustering of cavities inside the liquid layer/films, development of capillary waves, and formation of liquid droplets. For the first time, we observed and captured the occurrence of cavitation during the atomization of resting drops, films and impact droplets. The inertial cavitation events interfered with the capillary waves across the interphase boundary, puncturing and breaking the boundary to produce atomized mist. The in situ observation revealed the intricate dynamics of ultrasonic atomization and underscored the pivotal role of cavitation events throughout the entire atomization process. We also conducted experiments on ultrasonic atomization of liquid aluminum, producing particles of perfectly spherical shape. The particle size tended to decrease with reduced vibration amplitude Our work has demonstrated the important processing strategies on how to tailor the particle size while ensuring consistent particle shape and morphology, which is the key processing capability for producing high quality powders for additive manufacturing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

PowderJet: Spherical metal powder production via multi-orifice droplet-on-demand metal jetting

Leading metal additive manufacturing techniques, such as laser powder bed fusion and directed energy deposition, rely on high-quality spherical metal powders. However, traditional powder production methods like gas atomization face limitations, including low in-spec yield, asphericity, and internal porosity. We introduce PowderJet, a powder production platform that uses electromagnetic pulses to eject liquid metal droplets from a multi-orifice nozzle. Unlike stochastic methods, PowderJet tightly controls powder size, distribution, and purity through a droplet-on-demand approach. We detail the system’s design, operation, and performance using a combined experimental and computational fluid dynamics (CFD) framework. Initial results with Al4008 and Cu110 alloys demonstrate successful production, yielding unsieved aluminum powder batches with a mean diameter of 200 µm and a narrow size distribution (15 µm standard deviation). The produced powders are highly spherical, achieving a roundness > 0.95. PowderJet operates with a small melt volume (3 mL) and supports continuous refilling, enabling production rates between 30 and 140 cm³/hr depending on jetting frequency, number of orifices and particle size. CFD simulations show that future systems could achieve rates exceeding 1000 cm³/hr for particle sizes as small as 40 µm. PowderJet’s high yield of in-spec powder makes it ideal for producing precious or hazardous materials that are inefficient to manufacture using conventional methods. This platform offers a scalable, precise, and efficient solution for producing high-quality powders tailored for advanced manufacturing applications.

Atomization↗
DOE OSTI2026

Spaced out: An economic framework to explore the impacts of PV panel spacing on large-scale farming in Colorado

CONTEXT Agrivoltaic systems co-locate solar technologies with agricultural operations on an integrated plot of land and potentially provide benefits to both energy and agricultural systems. To date, large-scale (>5-MW) agrivoltaic projects in the United States have been limited to grazing and ecovoltaic applications, raising questions about the impact and scalability of agrivoltaic crop systems. Many agrivoltaic designs raise the height of the solar panels to accommodate agricultural practices while keeping energy density high. However, raising the panels results in increased photovoltaic (PV) development costs, which often are higher than the economic returns of crop production underneath the panels. This leads to unfavorable project economics and the need for other agrivoltaic solutions than raising panels. OBJECTIVE To explore other solutions, we perform an initial feasibility analysis for an agrivoltaic solution that can integrate with large-scale farming practices by increasing the row spacing in between panels. Increased PV row spacing is a low-cost approach for scaling agrivoltaics to accommodate crop production and this spacing can be tailored to required crop equipment for different regions. Increasing row spacing will reduce the power density (PV installed per acre), but in areas that are not land limited, these agrivoltaic designs could be economically feasible. Our analysis establishes a framework for a feasibility analysis for where and with what crops spaced out panel agrivoltaic solutions might be economical. METHODS Using a case study for large-scale agriculture crops in Colorado, we establish a framework for wide-row agrivoltaic economic feasibility analysis. We utilized the System Advisor Model to calculate technoeconomic metrics to compare different row spacing solutions and capture tradeoffs of these system designs. RESULTS AND CONCLUSIONS We find that, in some circumstances, wider row agrivoltaic solutions that allow for continued mechanized crop production can provide economic benefits over a traditional utility-scale PV system. For most crops examined in this analysis, roughly $\$$200/acre in agricultural profit justified spacing out the panels to at least 31.7 ft. to accommodate agrivoltaic configurations versus PV only configurations. Additionally, opportunities for increased agricultural revenue with agrivoltaic systems allow PV project economics to tolerate a larger range of CAPEX variability while remaining economically viable relative to the PV only configurations. SIGNIFICANCE This framework can be adapted for a wide variety of crops and regions and allows for examination of economically favorable sites for future agrivoltaic systems that utilize different configuration and expand opportunities for agrivoltaics.

14 SOLAR ENERGY↗
DOE OSTI2020

A new algae technical standards focus group: Summarizing and guiding the algae state of the art

The value proposition of algae technical metrics was the subject of a recent, industry-led, Focus Group interactive discussion. The interactive platform allowed for real time capturing and priority ranking of the topics that are deemed critical challenges for a future successful algae-based bioeconomy. This work ultimately sets the stage for providing guidance, methods, and standard reference materials tailored to respective algae industry segments for the cultivation, processing and marketing of high-quality and safe algae-based products. The group solicits input from the broader algae community on the value proposition and presents a case here to build a consensus around algae-specific metrics. The value proposition of technical standards to the industry is that guidance obtained through these collaborations builds producers' and consumers' trust that algae and algae-derived products are safe, reliable, and may allow for expanded market access, and increased competitiveness and international trade.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Lead tolerance and bioremoval by four strains of green algae from Nigerian fish ponds

Heavy metals from industry pose threats to human and environmental health. Microalgae are prime candidates to remove heavy metals from water and soil due to their metal-binding affinities, high growth rates, and contamination tolerance. Strain selection and composition of resulting contaminated biomass must be considered for downstream processing. In this study, we assessed the ability of four microalgae strains (Chlorophyceae) that were isolated from contaminated Nigerian fish ponds to take up dissolved lead at environmentally relevant concentrations (<0.05 mg L -1 – WHO standard). In a microplate assay, all strains grew in the presence of lead, tolerating concentrations up to 60 ppm, though the addition of dissolved lead affected the growth of the four strains. In a photobioreactor assay, all strains demonstrated the ability to take up dissolved lead, with removal efficiencies ranging from 86 to 93%. The concentrations of lead in contaminated biomass, removal efficiencies, and bioconcentration factors were greatest in one of the isolates Chlorella sp. MOW 12. Our results reinforce the fact that live microalgae have a greater biosorption capacity. Lead recovery from freeze-dried biomass using five different reagents showed that a 0.1 M hydrochloric acid solution was the most effective, with 83.4% recovery. We also showed that presence of lead in the culture medium resulted in an increase in the quantity of protein in the biomass. Elemental analysis of lead-bound biomass showed an increase in elements including boron and copper and a decrease in cobalt and sodium. Synergystic and antagonystic effect in uptake of other elements was strain specific, suggesting the possibility of tailored wastewater treatments depending on specific requirements.

59 BASIC BIOLOGICAL SCIENCES↗