Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Insights into the Transformation-Induced Plasticity (TRIP) Effect in Ti-Free Grade 300 Maraging Steel Manufactured by Laser Powder Bed Fusion (LPBF)

The near-net fabrication capabilities of laser powder-bed fusion (LPBF) offer the potential to manufacture tools with complex cooling channels that can improve the production efficiency of the tools with reduced greenhouse gas emissions. High strength, toughness, and wear resistance are some of the key properties required by the tooling industries to qualify tools. While strength can be increased through appropriate heat treatments, the increase in strength comes with an associated ductility loss. Here, we show that the non-equilibrium conditions inherent to LPBF can suppress the transformation-induced plasticity effect to room temperature in a Ti-free version of grade 300 maraging steel (G300MS), which is commonly not observed at room temperature in G300MS manufactured using conventional methods. The presence of retained austenite along with Ni-rich regions was found to increase the kinetics for austenite reversion during aging, thereby enabling the transformation of austenite into ε martensite during tensile deformation at room temperature, in turn increasing the strength with minimal ductility loss.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Physical Regime Sensitivity

Abstract This work presents a novel sensitivity approach that quantifies sensitivity to regimes of a model’s state variables rather than constitutive model parameters. This Physical Regime Sensitivity (PRS) determines which regimes of a model’s independent variables have the biggest influence on an experiment or application. PRS analysis is demonstrated on a strength model used in the simulation of a copper Taylor cylinder. In a series of simulations, the strength model was perturbed sequentially in local regimes of plastic strain, plastic strain rate, temperature and pressure, and then the prediction of cylinder shape was compared to unperturbed calculations. Results show, for example, that the deformed length of the cylinder was most sensitive to strength at a strain rate of 1.0 × 10 4 /sec., but the deformed footprint radius was most sensitive to strength at a strain rate of about 4.0 × 10 4 /sec. Compared to current histogram approaches, PRS can be used to design or interpret integrated experiments by identifying not just which regimes are accessed somewhere in the experiment but the causality question of which regimes actually affect the measured data. PRS should allow one to focus experimental and modeling efforts where they are most needed and to better interpret experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The effect of microstructure on the dynamic shock response of 1045 steel

Herein, the effect of microstructure on the shock response of 1045 steel is investigated via plate impact experiments and postmortem characterization. Three unique microstructures are explored: ferrite-pearlite, martensite, and ferrite with spheroidal cementite (i.e. spheroidized). Two spall recovery experiments, at approximate peak pressures of 3.2 and 3.5 GPa, are conducted to assess the Hugoniot elastic limit (HEL), spall strength, and damage morphology of the various microstructures. The ferrite-pearlite and martensite microstructures exhibit continuous yielding at both quasi-static and dynamic rates, while the spheroidized condition displays discontinuous yielding. Discontinuous yielding of the spheroidized microstructure is attributed to a combined low initial dislocation density coupled with a low dislocation nucleation rate. The spall strength of ferrite-pearlite is consistently lower than the spheroidized microstructure, attributed to elongated cementite that is more susceptible to cracking than more spherical cementite precipitates. Despite a high density of boundaries, martensite exhibits the highest spall strength. A large percentage of the boundaries within the martensite microstructure are found to be low energy (i.e. Σ3 or low angle), and are thus less susceptible to spall damage. Overall, the high spall strength of martensite is likely linked to traditional strengthening mechanisms that limit dislocation motion.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Material extrusion with integrated compression molding of NdFeB/SmFeN nylon bonded magnets using small- and large-scale pellet-based 3D-printers

High-density bonded rare-earth magnets are manufactured using pellet-fed additive manufacturing (AM)/material extrusion and an integrated additive manufacturing-compression molding (AM-CM) process. Neodymium iron boron – samarium iron nitride in polyamide 12 (NdFeB-SmFeN/PA12) of 93 % weight fraction (65 % volume fraction) are used for the study. The mechanical properties (tensile strength and modulus), magnetic properties (maximum energy density, coercivity, remanence) are reported. Manufacturing parameters such as layer height, barrel temperatures, screw speed and gantry feed rate are optimized to obtain the highest possible density of the magnets using a small-scale desktop material extrusion printer. Large scale integrated additive manufacturing-compression molding (AM-CM) is then utilized to increase the density of the magnets by reducing porosity defects common in the material extrusion process. The density of as-printed magnets was 5.2 g/cm 3 with a BH max value of 124.14 kJ/m 3 , tensile strength of 20 MPa and a modulus of 2 GPa. AM-CM increased the density of the compound by 5.5 % (5.49 g/cm 3 ). The reduction in porosity was confirmed using X-ray tomography (XCT). Improvement in mechanical strength of the material was also observed, with an increase in tensile strength of 25 % (25.09 MPa) and increase in tensile modulus of 275 % (5.49 GPa). Scanning electron microscopy showed increased particle-matrix adhesion with the integrated AM-CM process.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additively manufactured Al-Ce-Ni-Mn alloy with improved elevated-temperature fatigue resistance

Here, the high cycle fatigue behavior of an additively manufactured (AM) Al-10.5Ce-3.1Ni-1.2Mn wt% alloy was evaluated at 350 °C. The measured fatigue strength of 50 MPa at this temperature is comparable to the most fatigue resistant wrought Al alloys (2618-T6 and 7079-T6) at 315 °C. Refinement of pore populations through advanced AM processing in the examined alloy led to oxide inclusions becoming dominant fatigue crack initiation sites. The distribution of microstructural features that determine crack initiation was measured by X-ray computed tomography and served as input to make fatigue strength model predictions with various methodologies. A Monte-Carlo based approach that was previously applied to predict the fatigue strength of cast aluminum alloys through pore size distributions yielded accurate predictions for the fatigue strength of this AM alloy. Given the tunability of defect distributions in AM alloys, the sensitivity of the Al-Ce-Ni-Mn alloy fatigue behavior to defect distributions and outstanding elevated-temperature fatigue resistance of this alloy; the results together suggest the possibility of a new generation of fatigue-resistant alloys produced by the additive manufacturing route.

36 MATERIALS SCIENCE↗
DOE OSTI2023

3D Printed eutectic aluminum alloy has facility for site-specific properties

Additive manufacturing (AM) has the ability to print structures with site-specific properties. Existing AM approaches for site-specific properties are, however, based on complex processing-microstructure relationships in conventional alloys that were not designed for this purpose. Here, in this work, we report a straightforward approach for achieving site-specific properties that takes advantage of eutectic solidification characteristics. We demonstrate that the yield strength of a eutectic Al-Cu-Ce-Zr alloy can be tuned by varying the laser scan speed in concert with hatch spacing in laser powder bed fusion AM. A faster speed increases solidification rate resulting in finer eutectic spacing and higher strength. The hatch spacing is reduced at faster speeds to ensure overlap between melt pools which become smaller with increasing scan speed. The yield strength and its anisotropy relative to build direction are further tunable with a heat treatment. The scan speed-eutectic spacing-strength relationship is successfully applied to print a complex pattern of site-specific hardness in the alloy. The generalized principle of using AM for a eutectic alloy to create site-specific properties and anisotropy in properties is demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modelling dislocation-graphene interactions in a BCC Fe matrix by molecular dynamics simulations and gradient plasticity theory

We report graphene nanosheets (GNS) can enhance the strength and ductility of metal-based composites as they can obstruct the propagation of dislocations. The present article employs Molecular Dynamics (MD) simulations to investigate dislocation-GNS interaction mechanisms and possible influencing factors, including the number of GNS layers, the thickness of the metallic amorphous layer and the C - C bond strength. The results indicated that the shear strength of the metal/GNS interface and the bending stiffness of GNS determined the ability of GNS to block dislocation transmission. A physically based phenomenological parameter that can capture such dislocation-GNS interactions is the mechanical interface energy that has been put forth within gradient plasticity. By fitting the theoretical expressions to the simulation data, it was possible to obtain estimates for the mechanical interface energy for the GNS. It was found that increasing the GNS layers and adding an amorphous layer resulted in a strengthening in the stress–strain response and increased the value of this interfacial parameter. This indicates that the mechanical interfacial energy can be a unified measure for capturing and tuning the strength of various interfaces such as grain boundaries, GNS, amorphous-crystalline interface and bimetal interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Osteocytic oxygen sensing: Distinct impacts of VHL and HIF-2alpha on bone integrity

Skeletal fracture resistance emerges from multiple components of bone structure like microarchitecture, matrix mineralization, and organization. These characteristics are engendered via mechanisms like the hypoxia-inducible factors (HIF) pathway, involving two paralogs, HIF-1α and HIF-2α. Under normoxia, HIF-α is targeted for degradation via von-Hippel Lindau (VHL); hypoxia enables HIF-α stabilization and induction of target genes. We previously showed that osteocytic Vhl deletion or expression of degradation-resistant HIF-2α cDR female mice each produced high bone mass, whereas degradation-resistant osteocytic HIF-1α produced no overt phenotype. We report within that Vhl cKO increased bone strength, while HIF-2α cDR displayed markedly reduced bone strength below Cre-negative controls. This suggests that VHL and HIF-2α drive distinct responses that promote disparate effects on bone strength. Both Vhl deletion or HIF-2α accumulation generated two discrete bone morphologies: an outer lamellar cortex and a woven, poorly mineralized endocortex that imparted dramatically different functional outcomes. Our studies reveal novel influence of osteocytic HIF-2α signaling on collagen matrix organization, mineralization, and bone strength.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Mechanical behavior of carbonated MgO-based Engineered Cementitious Composite (ECC) after high temperatures exposure

Carbonated MgO-based Engineered Cementitious Composite (ECC) has ultrahigh tensile ductility and tight crack width control behavior. However, the expectation of improved fire-resistant has not been confirmed. This study explored the alterations to mechanical and microstructure characteristics of this material after exposure to temperatures up to 500 °C. Material mass loss, compressive strength, tensile strength, strain capacity, and matrix fracture toughness were measured. Scanning electron microscopy, mercury intrusion porosimetry, thermogravimetric analysis, and X-ray diffraction were used to probe the degradation of the cement matrix and fibers. The effect of elevated temperature on carbonated MgO-based ECC was further assessed via examination of the micromechanical behavior of the fiber-matrix. The objective of this research was to assess the performance of carbonated MgO-based ECC exposed to fire hazards. The tensile ductility of carbonated MgO-based ECC was found to be enhanced when exposed to ~100 °C as compared with those at room temperature ~20 °C. Further increase in exposure temperature, however, posed a negative impact on the composite compressive strength, ultimate tensile strength, and ability to control crack width. Here the results provide a useful database for further investigations into carbonated MgO-based ECC for fire safety enhancement.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Interlayer reinforcement of 3D printed concrete by the in-process deposition of U-nails

Highlights: • An in-process interlayer reinforcement approach for 3D concrete printing was proposed through the concurrent deposition of U-nails. • Significant strength and toughness improvement was achieved for U-nail reinforced 3D-printed concrete. • The bridge linking effect and dowel action of U-nails were analysed. • Response surface method were utilised to quantify the effects of U-nails on the interlayer bonding behaviour. 3D concrete printing has tremendous potential for construction manufacturing; however, weak interface bonding between adjacent layers remains a well-known issue that affects the mechanical properties of printed structures. The layers introduce anisotropy and reduce the capacity to resist tensile and shear loads. Reinforcements, inserted perpendicular to the printed layers to traverse the interfaces, can improve these limitations, but the insertion of reinforcements is difficult to achieve in practice, and there are few published studies exploring appropriate methods. This study presents a promising approach using U-shaped nails inserted into concrete during the printing process. The bridging effect and dowel action of the applied U-nails are visualised and analysed to elucidate the toughness improvement. The ultimate tensile strength and shear strength of 3D printed concrete are significantly increased by 145.0% and 220.0%, respectively. U-nails with a filament thickness of 2–2.5 mm are recommended to yield optimal improvement in the interlayer strength.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A microstructural investigation of a Na2SO4 activated cement-slag blend

The reactivity and early strength of cement:slag binders is usefully enhanced by the addition of sodium sulfate though the underlying mechanisms of the relationship between the enhanced hydration reactions and the structural aspects of the strength behavior remain unclear. In this study, microstructural development in the presence of Na{sub 2}SO{sub 4} was investigated utilizing mercury intrusion porosimetry (MIP), NMR relaxometry, and XRD. Increased rates of early strength development and decreased rates of late strength development due to the presence of added Na{sub 2}SO{sub 4} were linked to effects on capillary porosity refinement. While degree of hydration at later age was shown to have been lower in the presence of Na{sub 2}SO{sub 4}, and may have been responsible for the higher capillary porosity, a clear alteration in the pathway of microstructural development had occurred with inhibition to hydration of the slag component due to earlier microstructural development proposed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Novel processing route for design and manufacturing of metal toughened nanoceramics: Al–Al 2 O 3 nanocermets

Monolithic alumina is a highly brittle ceramic with a very low fracture toughness, making it an unreliable material for mechanical and structural applications. Ceramic-metal composites (cermets) are the subject of intensive interest to obtain materials which can address the intrinsic brittleness of ceramics without compromising their high strength and light weight. In the present investigation, aluminium-alumina (Al–Al 2 O 3 ) nanocermets were developed. The nanocermets possessed the toughness of Al phase and the strength of reinforced nano Al 2 O 3 particles. Here, the nanocermets green bodies were prepared such that upon sintering each adjacent Al 2 O 3 grain was conformally coated with a continuous Al film. Mechanical milling via a combination of cryo-milling and ball-milling was used to prepare Al–Al 2 O 3 nano-powder mixture. Spark plasma sintering was used to consolidate the green nanocermets. Results show that specimens prepared from 35 h milled powders exhibited superior mechanical properties as compared to other nanocermets, with an improvement in microhardness, elastic modulus, compressive strength, and flexural strength by 88%, 78%, 69% and 40% with respect to sintered pure Al. The indentation toughness of 35 h milled nanocermet showed an increment of 12.5% with respect to sintered pure Al 2 O 3 . Characterization techniques such as XRD, SEM, HR-TEM, X-ray tomography were employed to investigate the phase evolution and structural morphology, while FEM simulations were performed for understanding the crack propagation mechanisms in nanocermets.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A better understanding of the mechanics of borehole breakout utilizing a finite strain gradient-enhanced micropolar continuum model

Borehole breakout denotes the failure in rock mass subjected to drilling, caused by stress concentrations exceeding the material strength. Depending on the material properties, the preexisting in situ stress state, and the borehole dimensions, different types of borehole breakout, such as spiral-shaped breakout or v-shaped breakout, are distinguished in the literature. In the present work, we address the influence of the material properties on the predicted borehole breakout mode in a comprehensive finite element study. To this end, herein we employ a gradient-enhanced micropolar damage-plasticity model based on the Mohr–Coulomb strength criterion, formulated in the finite strain regime, which is calibrated based on experimental results from plane strain compression tests on Red Wildmoor sandstone. In the numerical study, the influence of the in situ stress state, the material friction angle, plastic dilation, post peak residual strength, and the inherent material length scale parameters are investigated. Thereby, we demonstrate that depending on the material parameters, substantially different failure modes, characterized by strongly localized shear bands or diffuse failure zones, are predicted. It is shown that in particular the brittleness of the material in the post peak regime has a major influence on the predicted breakout type. Moreover, a statistical validation of the results is obtained by considering different random field distributions of the initial material strength.

58 GEOSCIENCES↗
DOE OSTI2021

Enhancing functionalities in carbon fiber composites by titanium dioxide nanoparticles

Carbon fiber composite's high specific strength makes it incredibly useful for structural applications. However, their low strain-to-failure can be problematic in structural applications that can potentially see high strain conditions or high fatigue cycles resulting in sudden, catastrophic failure. This is further complicated by damage manifesting within the composite thus not showing damage indicators on the surface. Therefore, monitoring the structural integrity and strain history of the composite in application by itself—while maintaining positive composite performance—is vital to ensure safe operation. In this study, a homogeneous dispersion of TiO 2 nanoparticles on carbon fiber is demonstrated to generate a piezoresistive carbon fiber polymer matrix composite with enhanced self-sensing capabilities. The nanoparticle-embedded composites also exhibited superior strength and damping potential compared to the nanoparticle-free composites. The apparent interlaminar shear strength increased by up to 15% and the damping loss factor increased by an average of 150% while the piezoresistive sensitivity increased by up to 180% with the addition of a small weight fraction of nanoparticles to the fiber surface. These results demonstrate an approach to simultaneously improve the sensing capabilities, damping behavior and mechanical strength of carbon fiber composites by simply adding nanoparticles in the fiber sizing using a commercially scalable deposition method.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-situ effect in cross-ply laminates under various loading conditions analyzed with hybrid macro/micro-scale computational models

In this article, multi-scale finite element analyses based on three-dimensional (3D) hybrid macro/micro-scale computational models subjected to various loading conditions are carried out to examine the in-situ effect imposed by the neighboring plies on the failure initiation and propagation of cross-ply laminates. A detailed comparative study on crack suppression mechanisms due to the effect of embedded laminar thickness and adjacent ply orientation is presented. Furthermore, we compare the results of in-situ transverse failure strain and strength between the computational models and analytical predictions. Good agreements are generally observed, indicating the constructed computational models are highly accurate to quantify the in-situ effect. Subsequently, empirical formulas for calculating the in-situ strengths as a function of embedded ply thickness and different ply angle between embedded and adjacent plies are developed, during which several material parameters are obtained using a reverse fitting method. Finally, a new set of failure criteria for σ 22 -τ 12 , σ 22 -τ 23 , and σ 11 -τ 12 accounting for the in-situ strengths are proposed to predict laminated composites failure under multi-axial stress states. This study demonstrates an effective and efficient computational technique towards the accurate prediction of the failure behaviors and strengths of cross-ply laminates by including the in-situ effects.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Off-spec fly ash-based lightweight aggregate properties and their influence on the fresh, mechanical, and hydration properties of lightweight concrete: A comparative study

An off-spec fly ash-based spherical lightweight aggregate (LWA), designated as Spherical Porous Reactive Aggregate (SPoRA), was manufactured through a lab pilot-scale production and its engineering properties, including specific gravity, dry rodded unit weight, water absorption, mechanical performance, and pore structure, were evaluated. Using SPoRA, lightweight concrete (LWC) samples were made and their fresh, mechanical, and hydration properties were assessed and compared with LWC samples made using two commercial LWA available in the US market. The results indicated that fine and coarse SPoRA had 72 h water absorption capacities of 16.4 % and 20.9 %, respectively, which were higher than that of the two commercial LWAs. Higher saturated surface dry specific gravity of SPoRA compared to commercial LWAs led to a higher fresh density for the corresponding LWC. Using X-ray computed tomography, large spherical type pores were observed in SPoRA similar to those in the commercial slate-based LWA. Additionally, the pore size distribution of SPoRA, characterized by a dynamic vapor sorption analyzer, indicated that more than 97 % of the pores had diameters greater than 50 nm. SPoRA’s average bulk crushing strength was 6.8 MPa which was smaller than commercial LWA and was potentially attributed to the differences in manufacturing processes. Nonetheless, SPoRA LWC with 28 days compressive strength of 29 MPa passed the ASTM C330 requirement and had a comparable strength with LWC prepared with the commercial LWAs indicating lesser importance for the LWA strength. SPoRA LWC had a flowability of 5 % compared to LWC prepared with commercial LWAs having flowability of 18 %. This observation was potentially related to the fluxing agent used in the SPoRA production. SPoRA had a 70 % degree of hydration at 12 days which was comparable with that of LWC prepared with commercial LWA.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The Path towards Plasma Facing Components: A Review of State-of-the-art in W-Based Refractory High-Entropy Alloys

Developing advanced materials for plasma-facing components (PFCs) in fusion reactors is a crucial aspect for achieving sustained energy production. Tungsten (W) - based refractory high-entropy alloys (RHEAs) have emerged as promising candidates due to their superior radiation tolerance and high-temperature strength. This review paper will focus on recent advancements in W-based RHEA research, particularly emphasizing the key role of modelling using machine learning (ML) in the stage of discovery by predicting properties for each composition and expediting the identification of optimal RHEA compositions with desired properties. Additionally, the application of additive manufacturing (AM) techniques for fabricating W-based RHEAs is explored, highlighting their advantages for rapid prototyping and multi-compositional sample production in a high throughput manner. The review critically evaluates the current understanding of mechanical properties relevant to PFC applications, including high-temperature strength and ductility. Furthermore, the radiation tolerance of W-based RHEAs under irradiated conditions is discussed. Finally, the validity of current AM-manufactured W-based RHEAs as PFC materials is assessed, and key challenges and opportunities for future research are identified. This review aims to provide a comprehensive overview of W-based RHEAs for fusion applications and their potential to guide the development and validation of advanced refractory high entropy alloys.

Hatler, Caleb [University of Wisconsin-Madison]↗
DOE OSTI2023

Tuning acidity in silica-overcoated oxides for hydroalkoxylation

Mixed oxides are ubiquitious solid acid catalysts for a number of transformations. Here, the chemistry of mixed oxide interfaces was experimentally probed by constructing model SiO 2 on MO x interfaces using a liquid-phase, stoichiometrically-controlled deposition of tetraethyl orthosilicate (TEOS). Catalytically active Brønsted sites were generated in four series of overcoated SiO 2 on metal oxide materials prepared by depositing TEOS onto Al 2 O 3 , anatase TiO 2 , Nb 2 O 5 , and ZrO 2 . Pyridine DRIFTS studies indicate that the acidity of deposited silanol groups was enhanced by interaction with the metal oxide surface, suggesting that pseudo-bridging silanol type structures were formed. Trimethylphosphine oxide (TMPO) 31 P NMR experiments showed that Brønsted acid strength varied in the overcoated materials, with increasing strength in the following order: SiO 2 /ZrO 2 < SiO 2 /TiO 2 < SiO 2 /Nb 2 O 5 < SiO 2 /Al 2 O 3 . This order correlated with the Lewis acidity and chemical hardness of the underlying metal oxides. The catalytic performance of the materials was evaluated in the liquid-phase hydroalkoxylation of dihydropyran with n-octanol, revealing that activity was highly dependent on SiO 2 loading, which impacted the density of acid sites, and scaled exponentially with Brønsted acid strength, determined by the core metal oxide identity. Brønsted acid strength appears to be the key driver of the materials’ activity, with the highest areal rate of 2.2 mmol / m 2 – h being measured over SiO 2 /Al 2 O 3 . Furthermore, this study shows that SiO 2 -overcoated materials are a systematically tunable class of catalysts that can be applied to acid catalyzed reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗