Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “simplified analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Study of the single body yawed-wing aircraft concept

Areas relating to the development and improvement of the single-fuselage, yawed-wing transonic transport concept were investigated. These included: (1) developing an alternate configuration with a simplified engine installation;(2) determining a structural design speed placard that would allow the engine-airframe match for optimum airplane performance; and (3) conducting an aeroelastic stability and control analysis of the yawed-wing configuration with a flexible wing. A two-engine, single-fuselage, yawed-wing configuration was developed that achieved the Mach 1.2 design mission at 5560 km (3000 nmi) and payload of 18,140 kg (40,000 lb) with a gross weight of 217,700 kg (480,000 lb). This airplane was slightly heavier than the aft-integrated four-engine configuration that had been developed in a previous study. A modified structural design speed placard, which was determined, resulted in a 6% to 8% reduction in the gross weight of the yawed-wing configurations. The dynamic stability characteristics of the single-fuselage yawed-wing configuration were found to be very dependent on the magnitude of the pitch/roll coupling, the static longitudinal stability, and the dihedral effect.

Kulfan, R. M.↗
NASA NTRS1974

Advanced acoustic cavity technology

A series of rocket motor firings was performed in a modified linear aerospike thrust chamber with the H2/O2 propellant combination to allow determination of the physical properties of the combustion gases in acoustic cavities located in the chamber side walls. A preliminary analytical study was first conducted to define theoretically both the appropriate cavity dimensions and the combustion gas flow field adjacent to the cavity openings. During the subsequent motor firings, cavity gas temperature profiles were measured and gas samples were withdrawn from the bottom of the cavities for compositional analysis by measurement of pressure/temperature variation and gas chromatography. Data were obtained with both radially and axially oriented cavities and with and without hydrogen bleed flow through the cavities. A simplified procedure was developed for predicting gas cavity and acoustic velocity for use in acoustic cavity design analyses.

Hines, W. S.↗
NASA NTRS1974

A relativistic analysis of clock synchronization

The relativistic conversion between coordinate time and atomic time is reformulated to allow simpler time calculations relating analysis in solar-system barycentric coordinates (using coordinate time) with earth-fixed observations (measuring earth-bound proper time or atomic time.) After an interpretation of terms, this simplified formulation, which has a rate accuracy of about 10 to the minus 15th power, is used to explain the conventions required in the synchronization of a world wide clock network and to analyze two synchronization techniques-portable clocks and radio interferometry. Finally, pertinent experiment tests of relativity are briefly discussed in terms of the reformulated time conversion.

Thomas, J. B.↗
NASA NTRS1975

Study of growth of single crystal ribbon in space

The technical feasibility is studied of growing single-crystal silicon ribbon in the space environment. Procedures are described for calculating the electromagnetic fields produced in a silicon ribbon by an rf shaping coil. The forces on the ribbon and the degree of shaping to be expected are determined. The expected steady-state temperature distribution in the ribbon is calculated in the one-dimensional approximation. Calculations on simplified models indicate, that lack of flatness of the shaped ribbon and excessive heating of the melt by the eddy currents induced by the shaping fields may pose problems. An analysis of the relative effects of various kinds of forces other than electromagnetic showed that in the space environment capillarity forces would dominate, and that the shape of the melt is thus principally determined by the shape of any solids with which it comes in contact. This suggests that ribbon may be produced simply by drawing between parallel wires. A concept is developed for a process of off-angle growth, in which the ribbon is pulled at an angle to the solidification front. Such a process promises to offer increased growth rate, better homogeneity, and thinner ribbon.

Wood, V. E.↗
NASA NTRS1992

Vortex breakdown incipience: Theoretical considerations

The sensitivity of the onset and the location of vortex breakdowns in concentrated vortex cores, and the pronounced tendency of the breakdowns to migrate upstream have been characteristic observations of experimental investigations; they have also been features of numerical simulations and led to questions about the validity of these simulations. This behavior seems to be inconsistent with the strong time-like axial evolution of the flow, as expressed explicitly, for example, by the quasi-cylindrical approximate equations for this flow. An order-of-magnitude analysis of the equations of motion near breakdown leads to a modified set of governing equations, analysis of which demonstrates that the interplay between radial inertial, pressure, and viscous forces gives an elliptic character to these concentrated swirling flows. Analytical, asymptotic, and numerical solutions of a simplified non-linear equation are presented; these qualitatively exhibit the features of vortex onset and location noted above.

Berger, Stanley A.↗
NASA NTRS1993

View factors for perpendicular and parallel rectangular plates

Simplified expressions (in comparison to currently used expressions, such as one developed by Howell, 1982) are developed for computing the view factors for rectangular perpendicular and parallel plates in the analysis of radiant exchanges between surfaces separated by a radiatively transparent medium. It is shown that the reported expressions for rectangular perpendicular and parallel plates with varying position and size having parallel boundaries satisfy the properties of the view factors.

Ehlert, J. R.↗
NASA NTRS1993

Preliminary analysis and design optimization of the short spacer truss of Space Station Freedom

The analysis, dynamic simulation, and design optimization of the short spacer truss of the Space Station Freedom are presented in this report. The short spacer truss will be positioned between the integrated equipment assembly (IEA) and another truss, called the long spacer truss, in the Space Station Freedom. During its launch in the Space Shuttle, the truss will be subjected to considerable in-span distributed inertia loads due to shuttle accelerations. The short spacer truss, therefore, has been modeled as a space frame to account for flexural response. Several parameters have been assumed, since the design specifications are in the process of development; hence the results presented should be considered preliminary. However, the automated analysis and design capabilities that have been developed can readily be used to generate an optimum design of the short spacer truss once the actual specifications have been determined. This report includes static and dynamic analyses of the short spacer truss, which have been obtained with the linear elastic code LE-HOST (in these analyses, LE-HOST data files have been automated to facilitate their future use for different design specifications of the short spacer truss); the dynamic animation of the short spacer truss, which has been carried out by using the results of the dynamic analysis and a post-processing feature of the modeling code PATRAN; and the optimum-weight design of the spacer truss, which was obtained under prescribed stress, displacement, and frequency constraints by using the design code COMETBOARDS. Examination of the analysis and design results revealed that the design could be improved if the configuration of the short spacer truss were modified to a certain extent. A modified configuration, which may simplify fabrication, has been suggested. The performance of this configuration has been evaluated and was found to be satisfactory under both static and dynamic conditions.

Gendy, A. S.↗
NASA NTRS1993

Using the USCCS for sub microsecond spacecraft clock calibration

The Return Data Delay technique which requires knowledge of spacecraft range is commonly used for correlating a spacecraft clock against a ground time standard when millisecond accuracy is required. An analysis is presented that allows using the user spacecraft clock calibration system (USCCS) to correlate a spacecraft clock to better than one microsecond accuracy. The basic USCCS algorithm has been simplified and it is shown to result in about one microsecond accuracy without requiring orbital information. By considering the relative motion of the user satellite, the TDRS and the earth station about the center of the earth, a correction of almost two orders of magnitude can be made. Such accuracy is required for scientific investigations that require correlating coincident radiation or particle detection with a remote laboratory.

Sank, Victor J.↗
NASA NTRS1983

Transient responses of phosphoric acid fuel cell power plant system

An analytical and computerized study of the steady state and transient response of a phosphoric acid fuel cell (PAFC) system was completed. Parametric studies and sensitivity analyses of the PAFC system's operation were accomplished. Four non-linear dynamic models of the fuel cell stack, reformer, shift converters, and heat exchangers were developed based on nonhomogeneous non-linear partial differential equations, which include the material, component, energy balance, and electrochemical kinetic features. Due to a lack of experimental data for the dynamic response of the components only the steady state results were compared with data from other sources, indicating reasonably good agreement. A steady state simulation of the entire system was developed using, nonlinear ordinary differential equations. The finite difference method and trial-and-error procedures were used to obtain a solution. Using the model, a PAFC system, that was developed under NASA Grant, NCC3-17, was improved through the optimization of the heat exchanger network. Three types of cooling configurations for cell plates were evaluated to obtain the best current density and temperature distributions. The steady state solutions were used as the initial conditions in the dynamic model. The transient response of a simplified PAFC system, which included all of the major components, subjected to a load change was obtained. Due to the length of the computation time for the transient response calculations, analysis on a real-time computer was not possible. A simulation of the real-time calculations was developed on a batch type computer. The transient response characteristics are needed for the optimization of the design and control of the whole PAFC system. All of the models, procedures and simulations were programmed in Fortran and run on IBM 370 computers at Cleveland State University and the NASA Lewis Research Center.

Lu, Cheng-Yi↗
NASA NTRS2005

The EOS AURA Tropospheric Emission Spectrometer (TES): Status of the Program

This slide presentation is a programmatic overview covering some of the highlights of the mission and serve as an introduction to the accompanying presentations at the workshop. It reviews the goals and the products of the TES experiment, a simplified chemistry of ozone in both the stratosphere and troposphere, a description of the instrument, and the TES operational modes. Included are graphs showing some of the results of TES analysis of the key constituents of the tropospheric chemistry and the inter-regional transport.

Fourier Transform Infrared (FTIR)↗
NASA NTRS2013

Implications of CO Bias for Ozone and Methane Lifetime in a CCM

A low bias in carbon monoxide compared to observations at high latitudes is a common feature of chemistry climate models. CO bias can both indicate and contribute to a bias in modeled OH and methane lifetime. This study examines possible causes of CO bias in the ACCMIP simulation of the GEOSCCM, and considers how attributing the CO bias to uncertainty in CO emissions versus biases in other constituents impacts the relationship between CO bias and methane lifetime. We use a simplified model of CO tagged by source with specified OH to quantify the sensitivity of the CO bias to changes in CO emissions or OH concentration, comparing the modeled CO to surface and MOPITT observations. The simplified model shows that decreasing OH in the northern hemisphere removes most of the global mean and inter-hemispheric bias in surface CO. We then use results from this analysis to explore how adjusting CO sources in the CCM impacts the concentrations of ozone, OH and methane. The CCM simulation also exhibits biases in ozone and water vapor compared to observations. We use a parameterized CO-OH-CH4 model that takes ozone and water vapor as inputs to the parameterization to examine whether correcting water and ozone biases can alter OH enough to remove the CO bias. Through this analysis, we aim to better quantify the relationship between CO bias and model biases in ozone concentrations and methane lifetime.

carbon monoxide↗
NASA NTRS1980

Stress intensity factors in two bonded elastic layers containing cracks perpendicular to and on the interface. Part 1: Analysis

The basic crack problem which is essential for the study of subcritical crack propagation and fracture of layered structural materials is considered. Because of the apparent analytical difficulties, the problem is idealized as one of plane strain or plane stress. An additional simplifying assumption is made by restricting the formulation of the problem to crack geometries and loading conditions which have a plane of symmetry perpendicular to the interface. The general problem is formulated in terms of a coupled system of four integral equations. For each relevant crack configuration of practical interest, the singular behavior of the solution near and at the ends and points of intersection of the cracks is investigated and the related characteristic equations are obtained. The edge crack terminating at and crossing the interface, the T-shaped crack consisting of a broken layer and a delamination crack, the cross-shaped crack which consists of a delamination crack intersecting a crack which is perpendicular to the interface, and a delamination crack initiating from a stress-free boundary of the bonded layers are some of the practical crack geometries considered.

Lu, M. C.↗
NASA NTRS1981

Extended operating range of the 30-cm ion thruster with simplified power processor requirements

A 30-cm-diameter Hg ion thruster similar in design to the J-series thruster was operated at fixed conditions with only five power supplies and was throttled over the baseline power range with six supplies. An analysis of the functional model power processor showed that the component mass and parts count would be reduced by about 14 and 35% respectively, and the electrical efficiency would be increased about 1.5% by replacing power supplies with relays. By introducing new circuit designs, additional reductions in the component mass and parts, as well as an increase in electrical efficiency would be expected. The impact on thruster performance of reducing the number of power supplies was to lower the propellant utilization efficiency about 1.0% and raise the electrical efficiency values from 0.2 to 1.3% over the throttle range.

Rawlin, V. K.↗
NASA NTRS2005

Two Dimensional Viscoelastic Stress Analysis of a Prototypical JIMO Turbine Wheel

The designers of the Jupiter Icy Moons Orbiter (JIMO) are investigating the potential of nuclear powered-electric propulsion technology to provide deep space propulsion. In one design scenario a closed-Brayton-cycle power converter is used to convert thermal energy from a nuclear reactor to electrical power for the spacecraft utilizing an inert gas as the working fluid to run a turboalternator as described in L.S. Mason, "A Power Conversion for the Jupiter Icy Moons Orbiter," Journal of Propulsion and Power, vol. 20, no. 5, pp. 902-910. A key component in the turboalternator is the radial flow turbine wheel which may be fabricated from a cast superalloy. This turbine wheel is envisioned to run continuously over the life of the mission, which is anticipated to be about ten years. This scenario places unusual material requirements on the turbine wheel. Unlike the case of terrestrial turbine engines, fatigue, associated with start-up and shut-down of the engine, foreign-object damage, and corrosion issues are insignificant and thus creep issues become dominate. The purpose of this paper is to present estimates for creep growth of a prototypical JIMO turbine wheel over a ten year life. Since an actual design and bill of materials does not exist, the results presented in this paper are based on preliminary concepts which are likely to evolve over time. For this reason, as well as computational efficiency, a simplified 2-D, in lieu of a 3-D, viscoelastic, finite element model of a prototypical turbine wheel will be utilized employing material properties for the cast superalloy MAR-M247. The creep data employed in this analysis are based on preliminary data being generated at NASA Glenn Research Center.

Gayda, John↗
NASA NTRS1974

Methods studies toward simplified rotor-body dynamics, part 1

This report is directed to the problem of developing an adequate but not overly complex linear flight dynamics analytical model of a rotorcraft to study stability, control, gust and random turbulence responses. Since the conventional flight dynamics analysis using quasisteady rotor derivatives is adequate for the long period modes like the phugoid mode, only short time responses are considered here, where rotor-body coupling is of importance. Thus the body motion consists of pitch, roll and vertical motion, omitting linear longitudinal and lateral and yaw perturbations. Five analytical models of varying degree of sophistication are applied to a hypothetical hingeless compound helicopter operating up to .8 rotor advance ratio. Stability and response data are obtained for the basic helicopter and for the vehicle with two simple control feedback systems.

Hohenemser, K. H.↗
NASA NTRS1975

Error Analysis of the Shuttle Orbital Maneuvering System P-V-T Propellant Gaging Module. Mission Planning, Mission Analysis and Software Formulation

An investigation of the shuttle orbital maneuvering system (OMS) pressure-volume-temperature (P-V-T) propellant gaging module has revealed that the gaging errors due to the combined effects of random instrumentation measurement errors, propellant loading uncertainties, and simplifying assumptions in the software are non-linear over the range of the usable propellant quantity gage (0-100%), with the largest error being at the zero point. When the OMS propellant tanks in the orbiter vehicle pods are filled to contain 100% of the maximum usable propellant, the gaging error at the zero point was determined to be 9.5% for the fuel and 9.5% for the oxidizer. When the OMS propellant tanks initially contain 50% of the maximum usable propellant, the largest gaging error is still 9.5% for the fuel and 9.5% for the oxidizer.

Duhon, D. D.↗
NASA NTRS1981

Influence of landing gear flexibility on aircraft performance during ground roll

An analysis is made of the influence of landing gear deflection characteristics on aircraft performance on the ground up to rotation. A quasi-steady dynamic equilibrium state is assumed, including other simplifying assumptions such as calm air conditions and normal aircraft lift and drag. Ground incidence is defined as the angle made by the mean aerodynamic chord of the wing with respect to the ground plane, and equations are given for force and balance which determine the quasi-equilibrium conditions for the aircraft during ground roll. Results indicate that the landing gear deflections lead to a substantial increase in the angle of attack, and the variation in the ground incidence due to landing gear flexibility could be as much as + or - 50%, and the reduction in tail load requirements almost 25%.

Sivaramakrishnan, M. M.↗
NASA NTRS1981

A data base of geologic field spectra

It is noted that field samples measured in the laboratory do not always present an accurate picture of the ground surface sensed by airborne or spaceborne instruments because of the heterogeneous nature of most surfaces and because samples are disturbed and surface characteristics changed by collection and handling. The development of new remote sensing instruments relies on the analysis of surface materials in their natural state. The existence of thousands of Portable Field Reflectance Spectrometer (PFRS) spectra has necessitated a single, all-inclusive data base that permits greatly simplified searching and sorting procedures and facilitates further statistical analyses. The data base developed at JPL for cataloging geologic field spectra is discussed.

Kahle, A. B.↗