Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “refrigerators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Fast-airflow tumble clothes dryer with small thermoelectric heat pump: Experimental evaluation

Residential clothes drying accounts for about 5% of the total residential-sector energy consumption in the United States. Most dryers use electric resistance heaters to dry clothes and have low efficiencies. Higher-efficiency dryers that use vapor compression heat pumps are expensive and complex and have not gained a large market share in the United States. A novel tumble clothes dryer using a small thermoelectric heat pump with faster airflow than typical dryers is presented in this work. The benchtop performance of the thermoelectric heat pump and high-speed blower are presented, and the development of the prototype dryer is described. The dryer was tested for efficiency and dry time for a range of airflow rates and applied currents to the thermoelectric heat pump. The combined efficiency factor was 5.09–6.29 lb BDW /kWh (specific moisture extraction rate of 1.23–1.53 kg w /kWh) with 100–138 min dry times for these tests. The measured efficiency was 36 %–68 % greater than the minimum efficiency standard in the United States, and compared with vapor compression heat pump–based clothes dryers, the prototype dryer had less expensive, less complex components and did not use refrigerants. Finally, the performance of this small thermoelectric heat pump clothes dryer is also compared with previous iterations of the thermoelectric tumble clothes dryer described in the literature.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Broad Distribution of Local Polar States Generates Large Electrothermal Properties in Pb-Free Relaxor Ferroelectrics

Electrothermal energy conversion provides attractive solutions for global energy management, such as energy harvesting from waste heat using pyroelectric energy conversion (PEC) and efficient cooling of portable electronics or data servers using the electrocaloric effect. Relaxor ferroelectrics are attractive for electrothermal energy conversion because of their large pyroelectric coefficients over a wide temperature range. Although Pb-based relaxors are well-known, toxicity concerns have mandated the intense search for Pb-free alternatives. Here, we engineered (Ba,Ca)TiO 3 -based relaxors based on a multisite doping strategy, which show promising electrothermal performance, viz. a maximum PEC efficiency of 14% and electrocaloric refrigeration capacity of 115 J/kg. Using local-scale structural analysis, we provide an atomistic model for large electrothermal properties in the newly designed Pb-free ferroelectrics, whereby a temperature-independent continuous distribution of cation displacement directions creates easy pathways for microscopic polarization reorientation. This research provides key structural insight for future atomic-scale engineering of environmentally sustainable ferroelectrics in energy applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Spin-Glass-like State and Reversible Room-Temperature Magnetocaloric Effect in Double Distorted Perovskites Nd(Cu 3– x Mn x )Mn 4 O 12

The preparation, complex magnetic properties and room-temperature magnetocaloric effect in Nd(Cu 3–x Mn x )Mn 4 O 12 with cation distribution (Nd 3+ ) A (Cu 3–x 2+x Mn x 3+ ) A' (Mn 1+x 3+ Mn 3–x 4+ ) B O 12 2– (x = 1 and 1.5) have been reported. Both compounds show a sharp paramagnetic-ferromagnetic (FM) transition at T C of 300 and 280 K, respectively. The substitution of Cu by Mn at the A' site induces the emergence of a spin glass state below ≈63 K for x = 1 and ≈72 K for x = 1.5 compound. Another antiferromagnetic-like magnetic transition is also observed in both compounds at 23 and 28 K, respectively, which is discussed as the antiferromagnetic coupling between Nd 3+ at the A' site and (Mn 3+ /Mn 4+ ) at the B site. These two compounds exhibit room-temperature magnetocaloric effect. For a small field of 2 T, the maximum magnetic entropy changes –ΔS M are 1.5 J/kg K at 300 K and 1.4 J/kg K at 280 K, respectively. Furthermore, the –ΔS M (T) curves show an asymmetric distribution, resulting in high refrigerant capacity values for both compounds. We further demonstrate the distinct roles of the A'- and B-site spins on the magnetic properties and the origin of the spin-glass-like state in double distorted perovskites Ln(Cu 3–x Mn x )Mn 4 O 12 family of compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Magnetic and Magnetocaloric Properties of the A 2 LnSbO 6 Lanthanide Oxides on the Frustrated fcc Lattice

Frustrated lanthanide oxides are promising candidates for cryogen-free magnetic refrigeration due to their suppressed ordering temperatures and high magnetic moments. While much attention has been paid to the garnet and pyrochlore lattices, the magnetocaloric effect in frustrated face-centered cubic (fcc) lattices remains relatively unexplored. We previously showed that the frustrated fcc double perovskite Ba 2 GdSbO 6 is a top-performing magnetocaloric material (per mol Gd) because of its small nearest-neighbor interaction between spins. Here we investigate different tuning parameters to maximize the magnetocaloric effect in the family of fcc lanthanide oxides, A 2 LnSbO 6 (A = {Ba 2+ , Sr 2+ } and Ln = {Nd 3+ , Tb 3+ , Gd 3+ , Ho 3+ , Dy 3+ , Er 3+ }), including chemical pressure via the A site cation and the magnetic ground state via the lanthanide ion. Bulk magnetic measurements indicate a possible trend between magnetic short-range fluctuations and the field-temperature phase space of the magnetocaloric effect, determined by whether an ion is a Kramers or a non-Kramers ion. We report for the first time on the synthesis and magnetic characterization of the Ca 2 LnSbO 6 series with tunable site disorder that can be used to control the deviations from Curie–Weiss behavior. Taken together, these results suggest fcc lanthanide oxides as tunable systems for magnetocaloric design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Generation of Tin-Vacancy Centers in Diamond via Shallow Ion Implantation and Subsequent Diamond Overgrowth

Group IV color centers in diamond have garnered great interest for their potential as optically active solid-state spin qubits. The future utilization of such emitters requires the development of precise site-controlled emitter generation techniques that are compatible with high-quality nanophotonic devices. This task is more challenging for color centers with large group IV impurity atoms, which are otherwise promising because of their predicted long spin coherence times without a dilution refrigerator. For example, when applied to the negatively charged tin-vacancy (SnV – ) center, conventional site-controlled color center generation methods either damage the diamond surface or yield bulk spectra with unexplained features. Here we demonstrate a novel method to generate site-controlled SnV – centers with clean bulk spectra. We shallowly implant Sn ions through a thin implantation mask and subsequently grow a layer of diamond via chemical vapor deposition. This method can be extended to other color centers and integrated with quantum nanophotonic device fabrication.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multicaloric Cryocooling Using Heavy Rare-Earth Free La(Fe,Si) 13 -Based Compounds

The transition toward a carbon-neutral society based on renewable energies goes hand in hand with the availability of energy-efficient technologies. Here, magnetocaloric cooling is a very promising refrigeration technology to fulfill this role regarding cryogenic gas liquefaction. However, the current reliance on highly resource critical, heavy rare-earth-based compounds as magnetocaloric material makes global usage unsustainable. Here, we aim to mitigate this limitation through the utilization of a multicaloric cooling concept, which uses the external stimuli of isotropic pressure and magnetic field to tailor and induce magnetostructural phase transitions associated with large caloric effects. In this study, La 0.7 Ce 0.3 Fe 11.6 Si 1.4 is used as a nontoxic, low-cost, low-criticality multiferroic material to explore the potential, challenges, and peculiarities of multicaloric cryocooling, achieving maximum isothermal entropy changes up to −28 J (kg K) −1 in the temperature range from 190 K down to 30 K. Thus, the multicaloric cooling approach offers an additional degree of freedom to tailor the phase transition properties and may lead to energy-efficient and environmentally friendly gas liquefaction based on designed-for-purpose, noncritical multiferroic materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Elucidating the Microscale Behavior and Phase Separation Kinetics of Thermally Responsive Ionic Liquid–Water Mixtures

Thermally responsive ionic liquids (ILs) exhibit liquid-liquid phase separation into a water-rich (WR) and ionic-liquid-rich (ILR) phase when heated above a lower critical solution temperature (LCST). This phase behavior has been leveraged for applications ranging from forward osmosis (FO) desalination, where the IL acts as a draw solute, to refrigeration and dehumidification cycles, where the IL acts as a liquid desiccant. While significant effort has been devoted to characterizing the thermodynamic and thermophysical properties of LCST ILs, their phase separation kinetics have not been investigated. In this work, we describe the macroscale phase separation kinetics (phase separation time) by gleaning insight into the microscale colloidal behavior of aqueous mixtures of four different materials, P 4444 TFA (tetrabutylphosphonium-2,4-trifluoroacetate), P 4444 DMBS (tetrabutylphosphonium-2,4-dimethyl-benzenesulfonate), N 4444 Sal (tetrabutylammonium salicylate), and P 4444 Sal (tetrabutylphosphonium salicylate) as a function of IL concentration at a separation temperature of 70 °C. We report the discontinuous microscale size distributions for each material and correlate their theoretical settling velocities to experimental phase separation times. The results indicate that a simple Stokes' law model can predict the phase separation time within reasonable accuracy. Overall, this work lays the foundation for understanding the micro- to macroscale phase separation behavior and kinetics of LCST ILs for various water-energy applications.

LCST↗
DOE OSTI2026

Corrosion Resistance of Lignin-Based Thermoplastic Adhesive-Bonded Aluminum Joints

Adhesive-bonded joints are essential for lightweight, multimaterial automotive structures. We developed a lignin-based thermoplastic adhesive with adhesion strength comparable to conventional epoxy adhesives (20–23 MPa), while offering exceptional durability, recyclability, and corrosion resistance. Unlike commercial epoxy adhesives requiring refrigerated storage, our adhesive retains its bonding potential after a year of ambient conditioning. Bonded joints can be repeatedly disassembled and rejoined with less than 2% strength loss. After 500 h of salt fog exposure, the adhesive-bonded aluminum joints exhibited a 24% strength reduction, compared to 61% reduction in strength of joints based on a commercial epoxy adhesive.

Yu, Zeyang [ORNL] (ORCID:0000000209002374)↗
DOE OSTI2021

Investigation of the Production of Trifluoroacetic Acid from Two Halocarbons, HFC-134a and HFO-1234yf and Its Fates Using a Global Three-Dimensional Chemical Transport Model

Trifluoroacetic acid (TFA), a highly soluble and stable organic acid, is photochemically produced by certain anthropogenically emitted halocarbons such as HFC-134a and HFO-1234yf. Both these halocarbons are used as refrigerants in the automobile industry, and the high global warming potential of HFC-134a has promoted regulation of its use. Industries are transitioning to the use of HFO-1234yf as a more environmentally friendly alternative. In this work, we investigated the environmental effects of this change and found a 33-fold increase in the global burden of TFA from an annual value of 65 tonnes formed from the 2015 emissions of HFC-134a to a value of 2220 tonnes formed from an equivalent emission of HFO-1234yf. The percentage increase in surface TFA concentrations resulting from the switch from HFC-134a to HFO-1234yf remains substantial with an increase of up to 250-fold across Europe. The increase in emissions greater than the current emission scenario of HFO-1234yf is likely to result in significant TFA burden as the atmosphere is not able to disperse and deposit relevant oxidation products. The Criegee intermediate initiated loss process of TFA reduces the surface level atmospheric lifetime of TFA by up to 5 days (from 7 days to 2 days) in tropical forested regions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Observation of solid-state bidirectional thermal conductivity switching in antiferroelectric lead zirconate (PbZrO 3 )

Materials with tunable thermal properties enable on-demand control of temperature and heat flow, which is an integral component in the development of solid-state refrigeration, energy scavenging, and thermal circuits. Although gap-based and liquid-based thermal switches that work on the basis of mechanical movements have been an effective approach to control the flow of heat in the devices, their complex mechanisms impose considerable costs in latency, expense, and power consumption. As a consequence, materials that have multiple solid-state phases with distinct thermal properties are appealing for thermal management due to their simplicity, fast switching, and compactness. Thus, an ideal thermal switch should operate near or above room temperature, have a simple trigger mechanism, and offer a quick and large on/off switching ratio. In this study, we experimentally demonstrate that manipulating phonon scattering rates can switch the thermal conductivity of antiferroelectric PbZrO 3 bidirectionally by –10% and +25% upon applying electrical and thermal excitation, respectively. Our approach takes advantage of two separate phase transformations in PbZrO 3 that alter the phonon scattering rate in different manners. In this study, we demonstrate that PbZrO 3 can serve as a fast (<1 second), repeatable, simple trigger, and reliable thermal switch with a net switching ratio of nearly 38% from ~1.20 to ~1.65 W m –1 K –1 .

25 ENERGY STORAGE↗
DOE OSTI2026

Hierarchal structures tuned electrocaloric and electromechanical performance in PVDF-based tetrapolymers

Ferroelectrics with multifunctionalities are gaining increased interest in self-actuated electrocaloric effect (ECE) refrigerators. However, achieving high ECE and electromechanical (EM) coupling concomitantly for maximum heat transfer remains challenging. Here we present the structure-property relationship for poly(vinylidene fluoride-co-trifluoroethylene-co-chlorofluoroethylene-co-double bond), P(VDF-TrFE-CFE-DB), tetrapolymer, which exhibited a high ECE entropy change of 66.5 J Kg −1 K −1 and EM strain of −6.1%. We show that thermal treatment can be a key factor influencing multifunctional properties. High-temperature annealing incorporates DB and CFE units into crystalline grains to form extended-chain crystals, enabling CFE units to induce relaxor behavior and DB units to induce large structural changes at low electric fields. This synergy leads to an enhancement in both ECE and EM performances. Furthermore, at an optimized temperature of 50 °C, the annealed films exhibit giant cross-energy coupling, achieving ECE and EM performances of 100.8 J Kg −1 K −1 and −7.6%. This study provides insights into developing new ferroelectric polymers with electroactive multifunctionalities.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Population-based heteropolymer design to mimic protein mixtures

Biological fluids, the most complex blends, have compositions that constantly vary and cannot be molecularly defined. Despite these uncertainties, proteins fluctuate, fold, function and evolve as programmed. We propose that in addition to the known monomeric sequence requirements, protein sequences encode multi-pair interactions at the segmental level to navigate random encounters; synthetic heteropolymers capable of emulating such interactions can replicate how proteins behave in biological fluids individually and collectively. Here, we extracted the chemical characteristics and sequential arrangement along a protein chain at the segmental level from natural protein libraries and used the information to design heteropolymer ensembles as mixtures of disordered, partially folded and folded proteins. For each heteropolymer ensemble, the level of segmental similarity to that of natural proteins determines its ability to replicate many functions of biological fluids including assisting protein folding during translation, preserving the viability of fetal bovine serum without refrigeration, enhancing the thermal stability of proteins and behaving like synthetic cytosol under biologically relevant conditions. Molecular studies further translated protein sequence information at the segmental level into intermolecular interactions with a defined range, degree of diversity and temporal and spatial availability. This framework provides valuable guiding principles to synthetically realize protein properties, engineer bio/abiotic hybrid materials and, ultimately, realize matter-to-life transformations.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Two-component exciton condensates in an electron–hole bilayer

Macroscopic quantum coherence emerges when bosons condense into a Bose–Einstein condensate (BEC). Excitons are a long-sought solid-state route to high-temperature BECs with strong interactions, electrical tunability and potentially multicomponent spinor order, but conclusive evidence for equilibrium condensation has remained elusive. Here we report evidence for two-component exciton BECs in MoSe 2 /hBN/WSe 2 electron–hole bilayers by probing the spin–valley susceptibility of constituent electrons and holes. This heterostructure hosts equilibrium exciton fluids with four spin–valley flavours. Magneto-optical spectroscopy in a dilution refrigerator reveals three exciton condensate phases with distinct flavour polarizations. At zero magnetic field, the many-body ground state is a coherent superposition of two condensed intravalley exciton flavours. Under a magnetic field, the intravalley exciton condensate first switches to a two-component intervalley condensate through a first-order quantum phase transition at a weak critical field and then turns into a fully polarized single-component condensate at high fields. The condensate signatures form a dome in density–temperature space, persisting up to approximately 1.8 K. Our results establish van der Waals electron–hole bilayers as a versatile platform for strongly interacting, multicomponent exciton BECs.

Qi, Ruishi [University of California, Berkeley, CA↗
DOE OSTI2022

Development of spirulina for the manufacture and oral delivery of protein therapeutics

The use of the edible photosynthetic cyanobacterium Arthrospira platensis (spirulina) as a biomanufacturing platform has been limited by a lack of genetic tools. Here we report genetic engineering methods for stable, high-level expression of bioactive proteins in spirulina, including large-scale, indoor cultivation and downstream processing methods. Following targeted integration of exogenous genes into the spirulina chromosome (chr), encoded protein biopharmaceuticals can represent as much as 15% of total biomass, require no purification before oral delivery and are stable without refrigeration and protected during gastric transit when encapsulated within dry spirulina. Oral delivery of a spirulina-expressed antibody targeting campylobacter—a major cause of infant mortality in the developing world—prevents disease in mice, and a phase 1 clinical trial demonstrated safety for human administration. Spirulina provides an advantageous system for the manufacture of orally delivered therapeutic proteins by combining the safety of a food-based production host with the accessible genetic manipulation and high productivity of microbial platforms.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Lignin monomer conversion into biolubricant base oils

Despite progress in the depolymerization of lignin, only a few studies convert the obtained monomers to value-added products. Here we introduce a strategy to synthesize branched benzene lubricant (BBL) and branched cyclic lubricant (BCL) base oils from lignin-derived monomers and aldehyde. We perform carbon–carbon coupling via Brønsted acid-catalyzed hydroxyalkylation/alkylation (HAA) then hydrodeoxygenation (HDO). Optimum HAA reaction conditions achieve up to 90% guaiacol conversion and an HAA product containing 76% BBL and 24% enal condensation product over a P-SiO 2 catalyst. Subsequent HDO of HAA products over an Ir-ReO x /SiO 2 catalyst produces a lubricant-ranged mixture of BCL (C 24 ) up to yield (82%) and small fractions of dodecyl cyclohexane and C 10 and C 15 carbons alkanes. The kinematic viscosity, viscosity index, and Noack volatility of these base oils are comparable to commercial petroleum-derived poly α-olefin Group IV and refrigerant base oils. In conclusion, this approach provides a sustainable pathway for replacing petroleum-derived base oils.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Quantifying the environmental benefits of a solvent-based separation process for multilayer plastic films

Food packaging often appears in the form of multilayer (ML) plastic films, which leverage the functional properties of different polymers to achieve specific food protection goals (e.g., oxygen, water, and temperature barriers). These properties are essential to enable long shelf lives, reduce refrigeration usage, mitigate food waste, and increase food accessibility. However, ML film production processes generate large amounts of plastic waste that cannot be mechanically recycled. Recently, we have proposed a process, called solvent-targeted recovery and precipitation (STRAP), that enables the separation and recycling of the constituent polymers of ML films. This technology uses a series of solvent washes that selectively dissolve and precipitate target polymers. Quantifying the environmental benefits of STRAP over virgin resin production is essential for the commercial deployment of this technology. Further, this work uses life cycle assessment (LCA) methods to evaluate these impacts in terms of carbon footprint, energy use, water use, and toxicity. We analyze three STRAP process variants that use antisolvent and temperature-driven precipitation to treat different ML films. Our analysis reveals that the STRAP-A and STRAP-B process variants can provide environmental benefits over virgin film production. Furthermore, it gives valuable insight into the critical components of ML films (specific polymers) and of the STRAP processes (equipment) that are responsible for the highest impacts. Ultimately, we believe that the proposed analysis framework can lead to the design of more environmentally-friendly ML films and recycling processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Scalable, low-cost ink-based processing of high-performance silver selenide thermoelectrics

The growing global energy demand and its accelerating contribution to climate change emphasize the urgent need for sustainable energy conversion/harvesting technologies. Thermoelectric (TE) devices offer a compelling route to directly convert waste heat into electricity and enable solid-state cooling without moving parts or harmful refrigerants. Achieving their full potential requires not only higher TE performance (zT) but also scalable, low-cost manufacturing processes. Here, we introduce a transformative ink-based processing approach for scalable manufacturing of high-performance silver selenide-based TE materials and devices. Using a simple, high-throughput ink-mixing and blade coating strategy, our Ag 2 Se-based materials under the optimized composition and processing conditions yield an ultrahigh room-temperature power factor of 2.8 mW m −1 K −2 , over 100% higher than baseline samples and a reproducible figure of merit zT of 1 at room temperature. A thermoelectric generator (TEG) achieves a very competitive power density of 112 mW cm −2 at a 90 °C temperature difference between the hot and cold sides of the device, which is among the highest reported for silver selenide-based TE devices to date. This facile, scalable ink-based processing establishes a practical pathway toward industrial-scale manufacturing and widespread adoption of thermoelectric devices, advancing sustainable energy technologies.

Bappy, Md. Omarsany [University of Notre Dame, IN ↗
DOE OSTI2020

Magnetic field dependence of the martensitic transition and magnetocaloric effects in Ni 49 BiMn 35 In 15

The structural, magnetic, and magnetocaloric properties of the Bi-doped Heusler alloy Ni 49 BiMn 35 In 15 have been investigated using room temperature X-ray diffraction (XRD) and magnetization measurements in a temperature interval of 5-400 K. The alloy at room temperature was found to be in a mixture of a high temperature austenite phase (AP) and a low temperature martensite phase (MP). A drastic shift in the martensitic transition temperature at the rate of 16 K/T from 197 K to lower temperatures was observed. A kinetic arrest phenomenon of the AP was observed in the magnetization and electrical resistivity measurements during field-cooled (FC) measurements at 5T. A metamagnetic behavior characterized by a jump in magnetization in the isothermal M ( H ) curves near T M was observed. The maximum value of the magnetic entropy change and refrigerant capacity at Curie temperature were found to be 5.5 Jkg -1 K -1 and 312 Jkg -1 for μ o Δ H = 5T, respectively. A large magnetoresistance value of -56% was found near the martensitic transition.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗