Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “passivating layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

An investigation of passive control methods for shock-induced separation at hypersonic speeds

The effectiveness of several passive control techniques on shock-induced boundary-layer separation at hypersonic speed was investigated. Two approaches for alleviating the turbulent separation losses were examined: porous surface mass transfer and surface grooving. A total of four perforated surfaces with varying porosities were evaluated, and three groove orientations with respect to the freestream direction were studied. A comparison of the results from passive control techniques with those from an 'uncontrolled' shock impingement showed that the porous surface with the greatest porosity provided the greatest reduction in the pressure rise across the oblique shock wave. The grooved surface tested were found to be not effective; each of the grooved configurations examined increased the peak pressure value.

Rallo, R.↗

Nano-Engineering of Detector Surfaces to Offer Unprecedented Imager Sensitivity to Soft X-rays and Low Energy Electrons

The focus of this document is to record the learning and process development achieved by the completion of the Nano-Engineering of Detector Surfaces to Offer Unprecedented Imager Sensitivity to Soft X-rays and Low Energy Electrons LDRD. The goal of this effort was to study different silicon detector surface preparation methods such as ion implant parameters, and the addition of a quantum 2-layer superlattice. Enabling the preparation of the surface of silicon detectors (front side illuminated or bonded backside illuminated) increases the responsivity of the diode to shallowly absorbed photons. This increased sensitivity in turn allows for greater fidelity in imaging events that emit low soft X-rays or low energy electrons. Prior work has focused on passivating the surface of a silicon detectors with thin layers (tens of nm thick) of materials to reduce surface recombination sites. Measurements of visible light quantum efficiency, electron responsivity, and pulsed x-ray response indicate that detectors with a 2- layer superlattice enjoy a significant benefit over equivalent detectors using an ion implant at the illuminated surface.

42 ENGINEERING↗

Overview of the James Webb Space Telescope Observatory

The James Webb Space Telescope (JWST) is a cryogenic, 6.5 meter diameter space telescope. JWST has a unique architecture, compared to previous space telescopes, that is driven by its science requirements, ia passively cooled cryogenic design, and the need to stow the observatory for launch. JWST's large, segmented mirror meets the requirement for high angular resolution in the infrared coupled with a significant increase in collecting area compared to the Spitzer and Hubble Space telescopes in order to detect the first galaxies. JWST's unique five-layer sunshield allows the telescope and instrument module to passively cool to cryogenic temperatures. JWST will be launched on an Ariane 5, and so both its telescope optics, and the sunshield have to be stowed in order to fit the Ariane 5 fairing. Following launch the sunshield and telescope optics must be deployed, and the primary mirror phased for science operations. In this presentation we will review the design of the observatory and highlight recent progress in the construction of the JWST observatory. In particular, we address recent progress with the telescope optics, sunshield and spacecraft. We will discuss predicted observatory performance in terms of the scientific goals of JWST and address key operational considerations that might bear upon frontier science observations.

Clampin, Mark↗

Antireflection and SiO2 Surface Passivation by Liquid-Phase Chemistry for Efficient Black Silicon Solar Cells: Preprint

We report solar cells with both black Si antireflection and SiO2 surface passivation provided by inexpensive liquid-phase chemistry, rather than by conventional vacuum-based techniques. Preliminary cell efficiency has reached 16.4%. Nanoporous black Si antireflection on crystalline Si by aqueous etching promises low surface reflection for high photon utilization, together with lower manufacturingcost compared to vacuum-based antireflection coating. Ag-nanoparticle-assisted black Si etching and post-etching chemical treatment recently developed at NREL enables excellent control over the pore diameter and pore separation. Performance of black Si solar cells, including open-circuit voltage, short-circuit current density, and blue response, has benefited from these improvements. Prior tothis study, our black Si solar cells were all passivated by thermal SiO2 produced in tube furnaces. Although this passivation is effective, it is not yet ideal for ultra-low-cost manufacturing. In this study, we report, for the first time, the integration of black Si with a proprietary liquid-phase deposition (LPD) passivation from Natcore Technology. The Natcore LPD forms a layer of <10-nm SiO2on top of the black Si surface in a relatively mild chemical bath at room temperature. We demonstrate black Si solar cells with LPD SiO2 with a spectrum-weighted average reflection lower than 5%, similar to the more costly thermally grown SiO2 approach. However, LPD SiO2 provides somewhat better surface-passivation quality according to the lifetime analysis by the photo-conductivity decaymeasurement. Moreover, black Si solar cells with LPD SiO2 passivation exhibit higher spectral response at short wavelength compared to those passivated by thermally grown SiO2. With further optimization, the combination of aqueous black Si etching and LPD could provide a pathway for low-cost, high-efficiency crystalline Si solar cells.

14 SOLAR ENERGY↗

Characterization of carbon ion implantation induced graded microstructure and phase transformation in stainless steel

Austenitic stainless steel 316L is ion implanted by carbon with implantation fluences of 1.2 × 10{sup 17} ions-cm{sup −} {sup 2}, 2.4 × 10{sup 17} ions-cm{sup −} {sup 2}, and 4.8 × 10{sup 17} ions-cm{sup −} {sup 2}. The ion implantation induced graded microstructure and phase transformation in stainless steel is investigated by X-ray diffraction, X-ray photoelectron spectroscopy and high resolution transmission electron microscopy. The corrosion resistance is evaluated by potentiodynamic test. It is found that the initial phase is austenite with a small amount of ferrite. After low fluence carbon ion implantation, an amorphous layer and ferrite phase enriched region underneath are formed. Nanophase particles precipitate from the amorphous layer due to energy minimization and irradiation at larger ion implantation fluence. The morphology of the precipitated nanophase particles changes from circular to dumbbell-like with increasing implantation fluence. The corrosion resistance of stainless steel is enhanced by the formation of amorphous layer and graphitic solid state carbon after carbon ion implantation. - Highlights: • Carbon implantation leads to phase transformation from austenite to ferrite. • The passive film on SS316L becomes thinner after carbon ion implantation. • An amorphous layer is formed by carbon ion implantation. • Nanophase precipitate from amorphous layer at higher ion implantation fluence. • Corrosion resistance of SS316L is improved by carbon implantation.

36 MATERIALS SCIENCE↗

Effect of Lithium Doping on MgO Hydroxylation and Carbonation

Recovery of magnesium from brines can potentially be used to source MgO (periclase) as a CO 2 sorbent or for Mg-based cements. However, it is not clear how common impurities in brines, such as lithium, affect the resulting MgO reactivity. Here, to test the effect of lithium incorporation on MgO reactivity for hydration and carbonation, we combined computational simulations with experiments. Experimentally altered (Mg,Li)O with a low dopant concentration (0.012 ± 0.002% w/w Li) was characterized using synchrotron-based X-ray scattering and high-resolution electron microscopy to measure reaction layer formation on (Mg,Li)O. Single-crystal X-ray diffraction analysis of (Mg,Li)O demonstrates that the incorporation of lithium leads to the formation of oxygen vacancies. The presence of vacancies is likely causing faster hydroxylation rates as predicted by ab initio molecular dynamics simulations. However, the faster hydroxylation rates likely lead to faster passivation of the surface because we observe thinner reaction layers on (Mg,Li)O samples both over short time periods (30 days) and over long time periods (28 years). After 28 years, the reaction layer on the (Mg,Li)O sample was less than one-third of the thickness of that of the pure MgO sample. In addition, over 30 days, reaction layers on (Mg,Li)O samples primarily formed at steps rather than on terraces, in contrast to our previous observations on MgO. Based on our results, naturally occurring impurities in MgO modify its reactivity even at very low concentrations and need to be considered for accurate reaction rate prediction for application of MgO as a CO 2 sorbent or in cements.

MgO↗

Carbonation of MgO Single Crystals: Implications for Direct Air Capture of CO 2

Direct air capture (DAC) may be feasible to remove carbon dioxide (CO 2 ) from the atmosphere at the gigaton scale, holding promise to become a major contributor to climate change mitigation. Mineral looping using magnesium oxide (MgO) is potentially an economical, efficient, and sustainable pathway to gigaton-scale DAC. The hydroxylation and carbonation of MgO determine the efficiency of the looping process, but their rates and mechanisms remain uncertain. Here, in this work, MgO single crystals were reacted in air or CO 2 at varying humidities and characterized by X-ray scattering, microscopy, and vibrational spectroscopy. Results show that the hydroxylation formed a brucite (Mg(OH) 2 )-like layer immediately after crystal cleaving. Concurrently, the carbonation formed hydrated magnesium carbonate phases, including barringtonite (MgCO 3 ·2H 2 O) and nesquehonite (MgCO 3 ·2H 2 O), in the layer. Rapid initial growth of the layer is also manifested in short-range bending/warping of nanocrystallites, resulting in multiple orientations of the same phases on the surface. The layer growth slowed down over time, indicating surface passivation. The formation of barringtonite and nesquehonite with 1:1 CO 3 /Mg ratio indicates an efficient carbonation when compared to other magnesium carbonate phases of lower ratio. Our results are essential for understanding surface passivation mechanisms and tackling the passivation issue of mineral looping DAC technology.

54 ENVIRONMENTAL SCIENCES↗

The Influence of Structure and Processing on the Behavior of TiO 2 Protective Layers for Stabilization of n-Si/TiO 2 /Ni Photoanodes for Water Oxidation

Light absorbers with moderate band gaps (1–2 eV) are required for high-efficiency solar fuels devices, but most semiconducting photoanodes undergo photocorrosion or passivation in aqueous solution. Amorphous TiO 2 deposited by atomic-layer deposition (ALD) onto various n-type emiconductors (Si,GaAs, GaP, and CdTe) and coated with thin films or islands of Ni produces efficient, stable photoanodes for water oxidation, with the TiO 2 films protecting the underlying semiconductor from photocorrosion in pH = 14 KOH(aq). The links between the electronic properties of the TiO 2 in these electrodes and the structure and energetic defect states of the material are not yet well-elucidated. We show herein that TiO 2 films with a variety of crystal structures and mid-gap defect state distributions, deposited using both ALD and sputtering, form rectifying junctions with n-Si and are highly conductive towards photogenerated carriers in n-Si/TiO 2 /Ni photoanodes. Moreover, the photovoltage of these electrodes can be modified by annealing the TiO 2 in reducing or oxidizing environments. All of the polycrystalline TiO 2 films with compact grain boundaries investigated herein protected the n-Si photoanodes against photocorrosion in pH = 14 KOH(aq). Hence, in these devices conduction through the TiO 2 layer is neither specific to a particular amorphous or crystalline structure nor determined wholly by a particular extrinsic dopant impurity. The coupled structural and energetic properties of TiO 2 , and potentially other protective oxides, can therefore be controlled to yield optimized photoelectrode performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of atomic layer deposition temperature on current conduction in Al{sub 2}O{sub 3} films formed using H{sub 2}O oxidant

To develop high-performance, high-reliability gate insulation and surface passivation technologies for wide-bandgap semiconductor devices, the effect of atomic layer deposition (ALD) temperature on current conduction in Al{sub 2}O{sub 3} films is investigated based on the recently proposed space-charge-controlled field emission model. Leakage current measurement shows that Al{sub 2}O{sub 3} metal-insulator-semiconductor capacitors formed on the Si substrates underperform thermally grown SiO{sub 2} capacitors at the same average field. However, using equivalent oxide field as a more practical measure, the Al{sub 2}O{sub 3} capacitors are found to outperform the SiO{sub 2} capacitors in the cases where the capacitors are negatively biased and the gate material is adequately selected to reduce virtual dipoles at the gate/Al{sub 2}O{sub 3} interface. The Al{sub 2}O{sub 3} electron affinity increases with the increasing ALD temperature, but the gate-side virtual dipoles are not affected. Therefore, the leakage current of negatively biased Al{sub 2}O{sub 3} capacitors is approximately independent of the ALD temperature because of the compensation of the opposite effects of increased electron affinity and permittivity in Al{sub 2}O{sub 3}. By contrast, the substrate-side sheet of charge increases with increasing ALD temperature above 210 °C and hence enhances the current of positively biased Al{sub 2}O{sub 3} capacitors more significantly at high temperatures. Additionally, an anomalous oscillatory shift of the current-voltage characteristics with ALD temperature was observed in positively biased capacitors formed by low-temperature (≤210 °C) ALD. This shift is caused by dipoles at the Al{sub 2}O{sub 3}/underlying SiO{sub 2} interface. Although they have a minimal positive-bias leakage current, the low-temperature-grown Al{sub 2}O{sub 3} films cause the so-called blisters problem when heated above 400 °C. Therefore, because of the absence of blistering, a 450 °C ALD process is presently the most promising technology for growing high-reliability Al{sub 2}O{sub 3} films.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Comparison of passivation properties of plasma-assisted ALD and APCVD deposited Al 2 O 3 with SiN x capping

In this paper, we report on the direct comparison of Al 2 O 3 films deposited by plasma-assisted atomic layer deposition (ALD) and atmospheric pressure chemical vapor deposition (APCVD) techniques on the passivation properties of both bare and boron diffused Si surfaces. It is found that ALD and APCVD deposited Al 2 O 3 layers with SiN x capping have very similar chemical composition, hydrogen concentration at the Al 2 O 3 /Si interface, and interface defect density (D it ), but the ALD film has slightly higher negative fixed charge (Q f ) after a high temperature (~750 °C) contact firing cycle typically used for solar cell fabrication. Both films showed excellent surface recombination velocities of <5 cm/s on planar and textured un-diffused Si wafers, but the ALD films gave 1 to 8 fA/cm 2 lower emitter saturation current densities (J 0e ) on implanted boron emitters with sheet resistance in the range of 90–180 Ω/. This is attributed to the observed slightly higher negative charge-induced field-effect passivation in the ALD films. However, SiN x /Al 2 O 3 /p + /n/n + passivated emitter rear totally diffused (PERT) cell structures fabricated with 110 and 150 Ω/ emitter in this study showed no appreciable difference in cell efficiency. Device analysis and simulations showed that even for >23% high-performance solar cells design, with very low bulk and rear contact recombination, the observed small difference in J 0e has negligible effect on cell efficiency. Furthermore, APCVD Al 2 O 3 passivation of B emitter can produce comparable efficiencies to their counterpart ALD Al 2 O 3 passivated n-type Si solar cells.

14 SOLAR ENERGY↗

Operational stability of mixed Sn–Pb perovskite solar cells: Mechanisms, mitigation strategies, and perspectives

Mixed Sn–Pb perovskites provide the 1.2–1.3 eV narrow-bandgap absorber needed for high efficiency of all perovskite tandems, but their deployment is limited by operational instability under light. This review synthesizes mechanistic origins and recent mitigation strategies for mixed Sn–Pb perovskite solar cells. The oxidation of Sn 2+ to Sn 4+ , often driven by iodine formation under light and bias, is the primary failure pathway; it creates Sn vacancies, self-doping, and nonradiative loss. Surface/grain-boundary defects, halide migration, reactive oxygen species, and interfacial redox at charge-transport layers, along with hole accumulation from poor band alignment, further accelerate Sn–Pb perovskite degradation. Here we survey recent stability advances across additive chemistry, surface and grain-boundary passivation, buried-interface redesign with modified or alternative hole transport layers, and solvent systems that preserve Sn 2+ and correct Sn–Pb speciation for scalable coating. Together, these recent advances have enabled devices to retain 80%–90% output for hundreds to over a thousand hours. Lastly, we provide our perspectives on further improving the operational stability of Sn–Pb perovskite and solar cells.

14 SOLAR ENERGY↗

High and Ultra-High Temperature Reaction Kinetics by Single Nanoparticle Mass Spectrometry

Methodology is presented for non-destructive, optically-detected single nanoparticle (NP) mass spectrometry, with the goal of extracting surface reaction kinetics for single NPs at high temperatures. Methods for determining the NP charge, mass, and temperature as a function of time are discussed, and the data are used to extract both the absolute kinetics for mass change, as well as the efficiencies of the surface processes that cause them. Factors that contribute to the uncertainties in absolute and relative mass determination, and in the resulting kinetic parameters, are discussed. The method allows the NP-to-NP variations in initial reactivity to be measured directly, along with the time evolution of reactivity resulting from NP structural/compositional changes that occur under reaction conditions. The strengths and limitations of single nanoparticle mass spectrometry as a high temperature surface kinetics tool are discussed in the context of sublimation and O2 oxidation kinetics experiments for single hafnium (Hf) NPs at temperatures ranging above 2400 K. The Hf oxidation kinetics are compared to analogous oxidation experiments for silicon, graphite, and carbon black NPs. In all four cases, the oxidation chemistry was dominated by processes that result in net mass loss, and the distinct mechanisms responsible are discussed. All four NPs also eventually passivated, i.e., the efficiencies for oxidative etching decreased by at least two orders of magnitude, relative to the initial efficiencies. Furthermore, the passivation mechanisms, which are quite different for carbon, compared to silicon or hafnium, are discussed. Carbon NP passivation is attributed to structural isomerization leading to fully coordinated, fullerene-like NP surfaces, while for silicon and hafnium, passivation results from delayed formation of an oxide layer, triggered by accumulation of oxygen in the NP sub-surface region.

36 MATERIALS SCIENCE↗

Polyvinyl alcohol coating induced preferred crystallographic orientation in aqueous zinc battery anodes

The development of rechargeable aqueous zinc batteries is mainly hindered by the Zn anode, which suffers from dendrite growth, corrosion, hydrogen evolution, and surface passivation. Herein, a thin polyvinyl alcohol (PVA) coating layer on Zn anode has enabled dendrite-free, long-life aqueous Zn batteries by effectively regulating the interfacial ion diffusion and inducing the homogeneous Zn nucleation and deposition of stacked plates with preferentially crystallographic orientation along (002) Zn planes. The PVA@Zn anode achieved an ultralong cycle lifespan of thousands of hours at 0.25 and 1 mA cm -2 . Outstanding durability under a deep cycling capacity (5 mA h cm -2 ), high current density (10 mA cm -2 ), and long duration conditions were achieved. The superior cyclability of PVA@Zn anode was also demonstrated in PVA@Zn//V 2 O 5 full cells. In conclusion, the insights of PVA induced Zn deposition with preferred crystal orientation and interfacial regulation shed light on the future development of stable Zn anodes.

Crystallographic orientation↗

Resolving the Electron Plume within a Scanning Electron Microscope

Scanning electron microscopy (SEM), a century-old technique, is today a ubiquitous method of imaging the surface of nanostructures. However, most SEM detectors simply count the number of secondary electrons from a material of interest, and thereby overlook the rich material information contained within them. Here, by simple modifications to a standard SEM tool, we resolve the momentum and energy information on secondary electrons by directly imaging the electron plume generated by the electron beam of the SEM. Leveraging these spectroscopic imaging capabilities, our technique is able to image lateral electric fields across a prototypical silicon p–n junctions and to distinguish differently doped regions, even when buried beyond depths typically accessible by SEM. Intriguingly, the subsurface sensitivity of this technique reveals unexpectedly strong surface band bending within nominally passivated semiconductor structures, providing useful insights for complex layered component designs, in which interfacial dynamics dictate device operation. Further, these capabilities for noninvasive, multimodal probing of complicated electronic components are crucial in today’s electronic manufacturing but is largely inaccessible even with sophisticated techniques. These results show that seemingly simple SEM can be extended to probe complex and useful material properties.

36 MATERIALS SCIENCE↗

All-optical phase conjugation using diffractive wavefront processing

Abstract Optical phase conjugation (OPC) is a nonlinear technique used for counteracting wavefront distortions, with applications ranging from imaging to beam focusing. Here, we present a diffractive wavefront processor to approximate all-optical phase conjugation. Leveraging deep learning, a set of diffractive layers was optimized to all-optically process an arbitrary phase-aberrated input field, producing an output field with a phase distribution that is the conjugate of the input wave. We experimentally validated this wavefront processor by 3D-fabricating diffractive layers and performing OPC on phase distortions never seen during training. Employing terahertz radiation, our diffractive processor successfully performed OPC through a shallow volume that axially spans tens of wavelengths. We also created a diffractive phase-conjugate mirror by combining deep learning-optimized diffractive layers with a standard mirror. Given its compact, passive and multi-wavelength nature, this diffractive wavefront processor can be used for various applications, e.g., turbidity suppression and aberration correction across different spectral bands.

42 ENGINEERING↗

Suppressing defects through the synergistic effect of a Lewis base and a Lewis acid for highly efficient and stable perovskite solar cells

Achieving long-term operational stability at a high efficiency level for perovskite solar cells is the most challenging issue toward commercialization of this emerging photovoltaic technology. Here, we investigated the cooperation of a Lewis base and a Lewis acid by combining commercial bis-PCBM mixed isomers as the Lewis acid in the antisolvent and N -(4-bromophenyl)thiourea (BrPh-ThR) as the Lewis base in the perovskite solution precursor. The combination of the Lewis base and the Lewis acid synergistically passivates Pb 2+ and PbX 3– antisite defects, enlarges the perovskite grain size, and improves charge-carrier separation and transport, leading to improved device efficiency from 19.3% to 21.7%. In addition, this Lewis base and acid combination also suppresses moisture incursion and passivates pinholes generated in the hole-transporting layer. Furthermore, the unsealed devices remained at 93% of the initial efficiency value in ambient air (10–20% relative humidity) after 3600 h at 20–25 °C and dropped by 10% after 1500 h under continuous operation at 1-sun illumination and 55 °C in nitrogen with maximum power-point tracking.

14 SOLAR ENERGY↗

Optimizing the quality factor of InP nanobeam cavities using atomic layer deposition

Photonic crystal nanobeam cavities are valued for their small mode volume, CMOS compatibility, and high coupling efficiency-crucial features for various low-power photonic applications and quantum information processing. However, despite their potential, nanobeam cavities often suffer from low quality factors due to fabrication imperfections that create surface states and optical absorption. In this work, we demonstrate InP nanobeam cavities with up to 140% higher quality factors by applying a coating of Al 2 O 3 via atomic layer deposition to terminate dangling bonds and reduce surface absorption. Additionally, changing the deposition thickness allows precise tuning of the cavity mode wavelength without compromising the quality factor. This Al 2 O 3 atomic layer deposition approach holds great promise for optimizing nanobeam cavities that are well-suited for integration with a wide range of photonic applications.

42 ENGINEERING↗