Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optical absorption”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Nonoxidative dehydrogenation of propane using boron-incorporated silica-supported Pt Sites synthesized by atomic layer deposition

Nonoxidative dehydrogenation of propane to propylene using Pt-based supported catalysts is an active research area in catalysis because catalyst attributes of Pt sites can be controlled by careful design of active sites. One way to achieve this is by the addition of a second metal that may impart a change in the electron density of active sites, which in turn affects catalytic performance. In this study, bimetallic Pt and B sites were deposited on powder SiO2 using atomic layer deposition (ALD). Boron was first deposited on SiO2 via half-cycle ALD using triisoproplyborate as the B source. Following calcination, Pt deposition was performed via half-cycle ALD using trimethyl(methylcyclopentadienyl)platinum(IV) as the Pt source. The synthesized catalysts were reduced under H2 at 550 °C and characterized using inductively coupled plasma optical emission spectroscopy for elemental analysis, diffuse reflectance infrared Fourier transform spectroscopy of adsorbed CO to examine the properties of Pt, and time-resolved X-ray absorption near edge structure spectroscopy to examine the changes in the reducibility of Pt sites. The samples were then tested for nonoxidative dehydrogenation of propane at 550 °C using a fixed-bed plug-flow reactor to examine the role of B on the catalytic performance. Characterization results showed that the addition of B imparted an increase in electron density and affected the reducibility of Pt sites. In addition, incorporating B on SiO2 created anchoring sites for Pt ALD. The amount of Pt deposited on B/SiO2 was 2.2 times that on SiO2. Catalytic activity results revealed the addition of B did not change the initial activity of Pt sites significantly, but improved propylene selectivity from 80% to 87% and stability almost threefold. The enhanced selectivity and stability of PtB/SiO2 is most presumably due to favored desorption of propylene and mitigating coke formation under reaction conditions, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Exploring Fabrication of Ultra-low Absorption, Multilayer, Hafnium High Reflectors

Ultra-low absorption, high damage threshold coatings are critical for the advancement of the high power CW laser technologies, and in most cases, are a limiting factor for the output power. Since high power CW laser systems enable extremely high power irradiances, when the light is incident on an HR mirror, part of the energy is absorbed and converted into heat, which can have many detrimental side effects. The worst-case scenarios are optical distortion and laser-induced damage. These optics must operate reliably with irradiances of 100's kW/cm 2 to MW/cm 2 . The highest pulsed laser damage threshold high reflectors are consistently fabricated with hafnia material. However, hafnia is not the material of choice for high power CW laser systems because of very high absorption and scatter properties, factors of >100x higher than tantala-silica, due to its poly crystalline nature. This study focuses on CW laser use applications, where the coatings’ laser damage resistance is largely limited by the inherent absorption of the coating materials. The goal is to study the feasibility of utilizing a “composite” hafnium-silica and a “doped” hafnia-silica target materials to prohibit crystallization. The results from the study were extremely successful. Hafnia high reflectors coatings generated from this study exhibited one micron absorption values of approximately 1 ppm, which are the lowest reported values to date.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-resolution x-ray spectrometer for x-ray absorption fine structure spectroscopy

Two extended x-ray absorption fine structure flat crystal x-ray spectrometers (EFX’s) were designed and built for high-resolution x-ray spectroscopy over a large energy range with flexible, on-shot energy dispersion calibration capabilities. The EFX uses a flat silicon [111] crystal in the reflection geometry as the energy dispersive optic covering the energy range of 6.3–11.4 keV and achieving a spectral resolution of 4.5 eV with a source size of 50 μm at 7.2 keV. A shot-to-shot configurable calibration filter pack and Bayesian inference routine were used to constrain the energy dispersion relation to within ±3 eV. The EFX was primarily designed for x-ray absorption fine structure (XAFS) spectroscopy and provides significant improvement to the Laboratory for Laser Energetics’ OMEGA-60 XAFS experimental platform. The EFX is capable of performing extended XAFS measurements of multiple absorption edges simultaneously on metal alloys and x-ray absorption near-edge spectroscopy to measure the electron structure of compressed 3d transition metals.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Ultrafast optical modulation of vibrational strong coupling in ReCl(CO) 3 (2,2-bipyridine)

Polaritons – hybrid light-matter states formed from the strong coupling of a bright molecular transition with a confined photonic mode – may offer new opportunities for optical control of molecular behavior. Vibrational strong coupling (VSC) has been reported to impact ground-state chemical reactivity, but its influence on electronic excited-state dynamics remains unexplored. Here, we take a first step towards excited-state VSC by demonstrating optical modulation of the ReCl(CO) 3 (bpy), (bpy = 2,2-bipyridine) complex under VSC using femtosecond ultraviolet (UV)-pump/infrared (IR)-probe spectroscopy. We establish ground-state VSC of ReCl(CO) 3 (bpy) in a microfluidic Fabry-Pérot cavity equipped with indium tin oxide (ITO)-coated mirrors. ITO is effectively dichroic as it is reflective in the IR and transmissive in the UV-visible and therefore minimizes optical interference. Excitation with UV pump light drives ReCl(CO) 3 (bpy) into a manifold of electronic excited states that subsequently undergo non-radiative relaxation dynamics. We probe the transient response of the strongly-coupled system in the mid-IR, observing both Rabi contraction and cavity-filtered excited-state absorption signatures. We reconstruct the intrinsic response of intracavity molecules from the transient cavity transmission spectra to enable quantitative comparison with extracavity control experiments. We report no changes in the excited-state dynamics of ReCl(CO) 3 (bpy) under ground-state VSC. However, we do observe significant amplification of transient vibrational signals due to classical cavity-enhanced optical effects. This effort lays the groundwork to pursue direct excited-state VSC aimed at modulating photochemical reactivity.

cavity-enhanced spectroscopy↗
DOE OSTI2024

Coherent photoexcitation of entangled triplet pair states

The functional properties of organic semiconductors are defined by the interplay between optically bright and dark states. Organic devices require rapid conversion between these bright and dark manifolds for maximum efficiency, and one way to achieve this is through multiexciton generation (S 1 → 1 TT). Here, the dark state 1 TT is typically generated from bright S 1 after optical excitation; however, the mechanistic details are hotly debated. Here we report a 1 TT generation pathway in which it can be coherently photoexcited, without any involvement of bright S 1 . Using <10-fs transient absorption spectroscopy and pumping sub-resonantly, 1 TT is directly generated from the ground state. Applying this method to a range of pentacene dimers and thin films of various aggregation types, we determine the critical material properties that enable this forbidden pathway. Through a strikingly simple technique, this result opens the door for new mechanistic insights into 1 TT and other dark states in organic materials.

14 SOLAR ENERGY↗
DOE OSTI2024

Optical characterizations of densely doped Tm 3+ :KYW crystals at low temperatures

Abstract We investigate the optical lifetime, decay characteristics, spectral linewidth and energy level properties of thulium ions doped in a KY(WO 4 ) 2 crystal at 4 K temperature. High doping concentration of thulium ions with inhomogeneous broadening allow us to study nonradiative behaviors, instantaneous spectral diffusion, and spectral power broadening in this solid-state material. The theoretical consideration of ion–ion interactions is shown to accurately characterize the absorption, decay and other spectral behaviors of Tm 3 + ions. We observe more than ten-fold reduction in the decay time of 3 H 4 state and about three-fold reduction in the spectral-hole lifetime as we approach the center of the inhomogeneous broadening, corresponding to higher optical densities.

Lei, Yisheng (ORCID:0009000410141189)↗
DOE OSTI2022

Structural Phase Transitions between Layered Indium Selenide for Integrated Photonic Memory

The primary mechanism of optical memoristive devices relies on phase transitions between amorphous and crystalline states. The slow or energy-hungry amorphous–crystalline transitions in optical phase-change materials are detrimental to the scalability and performance of devices. Leveraging an integrated photonic platform, nonvolatile and reversible switching between two layered structures of indium selenide (In 2 Se 3 ) triggered by a single nanosecond pulse is demonstrated. The high-resolution pair distribution function reveals the detailed atomistic transition pathways between the layered structures. With interlayer “shear glide” and isosymmetric phase transition, switching between the α- and β-structural states contains low re-configurational entropy, allowing reversible switching between layered structures. Broadband refractive index contrast, optical transparency, and volumetric effect in the crystalline–crystalline phase transition are experimentally characterized in molecular-beam-epitaxy-grown thin films and compared to ab initio calculations. Finally, the nonlinear resonator transmission spectra measure of incremental linear loss rate of 3.3 GHz, introduced by a 1.5 µm-long In 2 Se 3 -covered layer, resulted from the combinations of material absorption and scattering.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Shaping the Infrared luminescence of Colloidal Nanocrystals Using a Dielectric Microcavity

As they have gained maturity, colloidal nanocrystals (NCs) have also expand the spectral range over of which they could be used for photonic and optoelectronic applications. In particular, the infrared use of NCs has become of utmost interest to develop cost-effective alternatives to current technologies. It is then critical not to let the material dictate the light–matter interaction, which is why the coupling of NCs to photonic cavities has been proposed. For infrared NCs, this approach has first been devoted to the control of absorption with in mind the increase of the signal magnitude for detectors. A Lot of efforts have been focused on the use of metallic metasurfaces. However, these generate significant optical losses and yield low quality factor. Here, this study rather focus on the coupling of infrared NCs to a dielectric mirror cavity. HgTe/CdS core-shell NCs are used and integrated into a cavity made of aperiodic dielectric mirrors. The effect of the substrate is systematically study on spectral linewidth, carrier dynamic, and emission directivity. The cavity is shown to narrow the PL by a factor 10, while focusing the emission over a 12° angle. Monitoring the power dependence of the emission, this study shows that the cavity leads to 250 K increase in the effective electronic temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-efficiency solar thermophotovoltaic system using a nanostructure-based selective emitter

Herein, we present the design, fabrication, optimization, and experimental results of a high-efficiency planar solar thermophotovoltaic (STPV) system utilizing a micro-textured absorber and a nanostructure multilayer metal-dielectric coated selective emitter fabricated on a tungsten (W) substrate. Light absorptance of more than 90% was achieved at visible and near-infrared wavelengths using the microtextured absorbing surface. The nanostructure selective emitter consists of two thin-film optical coatings of silicon nitride (Si3N4) and a layer of W in between to increase the surface emissivity in spectral regimes matching the quantum efficiency of the thermophotovoltaic (TPV) cells. Gallium antimonide (GaSb)-based TPV cells are used in our STPV design. The experiment was conducted at different operating temperatures using a high-power continuous wave laser diode stack as a simulated source of concentrated incident radiation. Our experimental setup measured a maximum electrical output power density of 1.71 W/cm 2 at 1676 K STPV temperature, and the overall power conversion efficiency of 8.4% after normalizing the output power density to the emitter area. This is the highest STPV system efficiency reported so far for any experimental STPV device. The incident optical laser power on the absorber side was 131 W. This is equivalent to a solar concentration factor of ~2100, which is within the practical limit and readily achievable with Fresnel lens setup.

14 SOLAR ENERGY↗
DOE OSTI2024

Multi-Parameter Optical Fiber for Distributed Sensing of Humidity, CH4, CO2, and Corrosion

This work describes the use of the optical fiber sensor (OFS) for successful monitoring of humidity, CH4, and CO2 based on the strain produced along the single-mode fiber (SMF) sensor. This is enabled by absorption of H2O/gases onto the commercially available polyacrylate coated jacketed portion of the fiber resulting in a change in strain. Under equilibrium, a differential microstrain was observed along the jacketed portion of the SMF with N2, CH4, and CO2 at different relative humidity (RH) conditions. The strain response of the SMF under various mixed gas composition and different RH conditions were also measured and made calibration curves accordingly. Linear regression and principal component analysis of the strain datasets provided deconvolution of the impact of strain from H2O, N2, CH4, and CO2. Additionally, modified OFS comprised of the Fe coated fiber section was employed to monitor corrosion based on the increase in backscattered intensity amplitude of the light being passed once corrosion of Fe occurs. Also, corrosion of Fe was studied under soil by installing the fiber in soil with protective measures which would prevent the sensor being mechanically disturbed or broken during installation. The corrosion rates were studied by monitoring the rate at which the intensity of backscattered light amplitude attains a steady state value when complete corrosion of Fe with a specific coating thickness occurs.

Mainali, Badri↗
DOE OSTI2025

PROCESS-STRUCTURE-PROPERTY RELATIONSHIPS IN LASER POWDER BED FUSION PRODUCED 17-4 PH STEEL

Laser powder bed fusion (LPBF) is a metal additive manufacturing method that produces non-traditional microstructures as a result of the rapid solidification and thermal cycling inherent to the process. When using LPBF-produced material in application, these unique microstructures challenge the applicability of well developed mechanical property databases achieved by conventional heat treatments. For wider adoption of this technology, a more holistic understanding is necessary on how process attributes develop material structure, which dictate mechanical properties. This dissertation explores the process– structure–property relationships in LPBF 17-4 PH steel through systematic evaluation of atmospheric processing and heat treatment effects on microstructure and mechanical performance. Specimens were fabricated under controlled build environments, subjected to a range of solutionizing, homogenizing, and aging treatments, and characterized using optical microscopy, electron back scatter diffraction (EBSD), and X-ray diffraction (XRD) to quantify phase evolution. Tensile testing was performed to directly link heat treatment pathway and nitrogen absorption to mechanical performance. This work demonstrates where conventional heat treatment standards are applicable to LPBF 17-4 PH steel and where modifications are required. By directly correlating phase stability, nitrogen effects, and tensile response, this work provides practical guidelines for tailoring post-processing strategies. These findings underscore that successful application of LPBF 17-4 PH steel requires explicit consideration of both build environment and post-processing. By linking processing conditions to microstructure and performance, this work advances understanding of critical variables that govern reliability of additively manufactured precipitation-hardened stainless steels in demanding applications.

Brown, Benjamin [Kansas City National Security Cam↗
DOE OSTI2023

Floquet engineering of strongly driven excitons in monolayer tungsten disulfide

Interactions of quantum materials with strong-laser fields can induce exotic nonequilibrium electronic states. Monolayer transition-metal dichalcogenides, a new class of direct-gap semiconductors with prominent quantum confinement, offer exceptional opportunities toward Floquet engineering of quasiparticle electron-hole states, or excitons. Strong-field driving has a potential to achieve enhanced control of electronic band structure, thus a possibility to open a new realm of exciton light-matter interactions. However, experimental implementation of strongly-driven excitons has so far remained out of reach. Here, we use mid-infrared laser pulses below the optical bandgap to excite monolayer tungsten disulfide up to a field strength of 0.3 V/nm, and demonstrate strong-field light dressing of excitons in the excess of a hundred millielectronvolt. Our high-sensitivity transient absorption spectroscopy further reveals formation of a virtual absorption feature below the 1s-exciton resonance, which is assigned to a light-dressed sideband from the dark 2p-exciton state. Quantum-mechanical simulations substantiate the experimental results and enable us to retrieve real-space movies of the exciton dynamics. Here, this study advances our understanding of the exciton dynamics in the strong-field regime, and showcases the possibility of harnessing ultrafast, strong-field phenomena in device applications of two-dimensional materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Unique signatures of the Rashba effect in the magneto-optical properties of two-dimensional semiconductors

Herein, the authors theoretically demonstrate two simple magneto-optical measurements which can be used to confirm the existence of Rashba terms in two dimensional semiconductors, even in samples of unoptimal quality, where the transition line widths are comparable to or larger than the Landau level splitting. The first is magnetic circular dichroism (MCD), where a giant MCD signal should be observed at the band edge in the presence of Rashba terms. The second is the comparison of the diamagnetic shift measured in absorption with that in photoluminescence which occurs from the dispersion minimum of the Rashba exciton.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Molecular Characterization of Water-Soluble Brown Carbon Chromophores in Snowpack from Northern Xinjiang, China

This study reports molecular-level characterization of brown carbon (BrC) attributed to water-soluble organic carbon in six snowpack samples collected from northern Xinjiang, China. Here, the molecular composition and light-absorbing properties of BrC chromophores were unraveled by application of high-performance liquid chromatography (HPLC) coupled to a photodiode array (PDA) detector and high-resolution mass spectrometry. The chromophores were classified into five major types, that is, (1) phenolic/lignin-derived compounds, (2) flavonoids, (3) nitroaromatics, (4) oxygenated aromatics, and (5) other chromophores. Identified chromophores account for ~23–64% of the total light absorption measured by the PDA detector in the wavelength range of 300–370 nm. In the representative samples from urban and remote areas, oxygenated aromatics and nitroaromatics dominate the absorption in the wavelengths below and above 320 nm, respectively. The highly polluted urban sample shows the most complex HPLC-PDA chromatogram, and more other chromophores contribute to the bulk absorption. Phenolic/ lignin-derived compounds are the most light-absorbing species in the soil-influenced sample. Chromophores in two remote samples exhibit ultraviolet–visible features distinct from other samples, which are attributed to flavonoids. Identification of individual chromophores and quantitative analysis of their optical properties are helpful for elucidating the roles of BrC in snow radiative balance and photochemistry.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Optimizing energy yield of monolithic perovskite/silicon tandem solar cells in real-world Conditions: The impact of luminescent coupling

Efficient light management is key to maximizing power conversion efficiency (PCE) in monolithic perovskite/silicon tandem solar cells. Achieving peak efficiency requires closely matched current generation in all junctions, especially in integrated configurations. However, real-world conditions vary significantly due to factors such as sunlight spectrum, diffuse-to-direct sunlight ratio, angular distribution of light, subcell temperature coefficients, and ground reflection. This study introduces a comprehensive optical and device simulation to optimize perovskite/silicon tandem cells, considering experimental luminescent coupling (LC) efficiency and its dependence on working conditions, alongside variations in radiative recombination, effect of temperature on absorptivity spectra, and cloud cover. Our results show potential energy yield improvements of up to 1.4 % with LC, based on current perovskite radiative recombination records, and up to 4 % with direct bandgap materials. Although radiative recombination's dependence on excitation intensity reduces output power and requires thicker absorbers, LC compensates for these losses. LC also lowers the optimized bandgap for the perovskite top cell from 1.72 eV to 1.64–1.68 eV, or even lower in regions with redshifted irradiance. Additionally, optimization revealed that thinner silicon bottom cells require a higher perovskite top cell bandgap, impacting the balance between fabrication cost and cell stability.

14 SOLAR ENERGY↗
DOE OSTI2023

Unraveling Triplet Formation Mechanisms in Acenothiophene Chromophores

The evolution of molecular platforms for singlet fission (SF) chromophores has fueled the quest for new compounds capable of generating triplets quantitatively at fast time scales. As the exploration of molecular motifs for SF has diversified, a key challenge has emerged in identifying when the criteria for SF have been satisfied. Here, we show how covalently bound molecular dimers uniquely provide a set of characteristic optical markers that can be used to distinguish triplet pair formation from processes that generate an individual triplet. These markers are contained within (i) triplet charge-transfer excited state absorption features, (ii) kinetic signatures of triplet-triplet annihilation processes, and (iii) the modulation of triplet formation rates using bridging moieties between chromophores. Our assignments are verified by time-resolved electron paramagnetic resonance (EPR) measurements, which directly identify triplet pairs by their electron spin and polarization patterns. Here we apply these diagnostic criteria to dimers of acenothiophene derivatives in solution that were recently reported to undergo efficient intermolecular SF in condensed media. While the electronic structure of these heteroatom-containing chromophores can be broadly tuned, the effect of their enhanced spin-orbit coupling and low-energy nonbonding orbitals on their SF dynamics has not been fully determined. We find that SF is fast and efficient in tetracenothiophene but that anthradithiophene exhibits fast intersystem crossing due to modifications of the singlet and triplet excited state energies upon functionalization of the heterocycle. We conclude that it is not sufficient to assign SF based on comparisons of the triplet formation kinetics between monomer and multichromophore systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Functional Nanomaterials with Tunable Plasmonic and Emittive Properties (Final Project Report)

The goal of the project is on understanding the principles of non-covalent assembling of tunable functional materials with various nanocrystals in order to control light-matter interactions by changing localized interfacial refractive properties, coupling parameters, or the ionic environment of surrounding media. We explore novel soft functional matrices with controlled physical properties via the application of light, mechanical stresses, ionic environment, and electrical potential. These functional matrices is used in conjunction with novel anisotropic inorganic nanostructures such as noble metal/metal alloy anisotropic nanostructures with complex optical properties (multiple LSPR modes) and quantum dots with light-emissive or absorbing properties in a broad spectral range from the UV to the NIR for efficient solar energy absorption and light conversion.

36 MATERIALS SCIENCE↗