Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “numerical modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

A semi-analytical method for simulating matrix diffusion in numerical transport models

We report a semi-analytical approximation for transient matrix diffusion is developed for use in numerical contaminant transport simulators. This method is an adaptation and extension of the heat conduction method of Vinsome and Westerveld (1980) used to simulate heat losses during thermally enhanced oil recovery. The semi-analytical method is used in place of discretization of the low permeability materials, and it represents the concentration profile in the low permeability materials with a fitting function that is adjusted in each element at each time-step. The resulting matrix diffusion fluxes are added to the numerical model as linear concentration-dependent source/sink terms. Since only the high permeability zones need to be discretized, the numerical formulation is extremely efficient compared to traditional approaches that require discretization of both the high and low permeability zones. The semi-analytical method compares favorably with the analytical solution for transient one-dimensional diffusion with first order decay, with a two-layer aquifer/aquitard solution, with the solution for transport in a fracture with matrix diffusion and decay, and with a fully numerical solution for transport in a thin sand zone bounded by clay with variable decay rates.

54 ENVIRONMENTAL SCIENCES↗

Topology optimization beyond linear elasticity

Complex, non-linear path-dependent and transient response of engineering structures can today be numerically modeled with good accuracy. For linear systems, this modeling has successfully been combined with computational design optimization for many years. The combination of non-linear modeling and numerical design optimization is far less established. In the present paper we discuss some recent steps taken to close the gap between the use of linear and non-linear modeling with numerical optimization. Examples with nonlinear elasticity, finite strain plasticity and dynamic modeling combined with topology optimization are discussed.

42 ENGINEERING↗

LaserOrigami (LO) of three-dimensional (3D) components: Experimental analysis and numerical modeling-part II

The present work explores how the choice of the scanning patterns can affect the final shapes of 3D components manufactured by laser-origami with a High-Power Diode Laser (HPDL). The experimental approach allowed the achievement of high bending angles, also avoiding any distortion on the surface of AISI 304 stainless steel workpiece. Optimization of the operational parameters led to the best prototype of the 3D components, with the closest respect of the strictest dimensional and geometrical tolerances. In addition, a thermo-mechanical model to predict the final shape of the 3D components was developed. The numerical model, implemented by Finite Element Method (FEM), was discovered to be a reliable tool in predicting the final shape of the prototypes, matching with a great deal of accuracy the experimental results. Specifically, the model allowed the estimation of the temperature distribution and nodal displacements of the components varying both the setting of the laser parameters and the choice of the scanning patterns.

47 OTHER INSTRUMENTATION↗

ASSIMILATION OF DOPPLER RADAR DATA INTO NUMERICAL WEATHER MODELS

During the year 2008, the United States National Weather Service (NWS) completed an eight fold increase in sampling capability for weather radars to 250 m resolution. This increase is expected to improve warning lead times by detecting small scale features sooner with increased reliability; however, current NWS operational model domains utilize grid spacing an order of magnitude larger than the radar data resolution, and therefore the added resolution of radar data is not fully exploited. The assimilation of radar reflectivity and velocity data into high resolution numerical weather model forecasts where grid spacing is comparable to the radar data resolution was investigated under a Laboratory Directed Research and Development (LDRD) 'quick hit' grant to determine the impact of improved data resolution on model predictions with specific initial proof of concept application to daily Savannah River Site operations and emergency response. Development of software to process NWS radar reflectivity and radial velocity data was undertaken for assimilation of observations into numerical models. Data values within the radar data volume undergo automated quality control (QC) analysis routines developed in support of this project to eliminate empty/missing data points, decrease anomalous propagation values, and determine error thresholds by utilizing the calculated variances among data values. The Weather Research and Forecasting model (WRF) three dimensional variational data assimilation package (WRF-3DVAR) was used to incorporate the QC'ed radar data into input and boundary conditions. The lack of observational data in the vicinity of SRS available to NWS operational models signifies an important data void where radar observations can provide significant input. These observations greatly enhance the knowledge of storm structures and the environmental conditions which influence their development. As the increase in computational power and availability has made higher resolution real-time model simulations possible, the need to obtain observations to both initialize numerical models and verify their output has become increasingly important. The assimilation of high resolution radar observations therefore provides a vital component in the development and utility of numerical model forecasts for both weather forecasting and contaminant transport, including future opportunities to improve wet deposition computations explicitly.

54 ENVIRONMENTAL SCIENCES↗

Treatment of cloudiness in regional scale - Numerical weather prediction models

A numerical weather prediction model is considered in which cloud water and precipitation are explicitly predicted as functions of three space dimensions and time. Approximations in the thermodynamic and continuity equations are discussed in detail, as well as the cumulus parameterization and the cloud microphysics parameterization. An example of a real-data forecast indicates that very accurate quantitative precipitation and cloud cover forecasts are possible using initial observations from only the relatively sparse rawinsonde network in the U.S.

Kreitzberg, C. W.↗

Constraining Numerical Geodynamo Modeling with Surface Observations

Numerical dynamo solutions have traditionally been generated entirely by a set of self-consistent differential equations that govern the spatial-temporal variation of the magnetic field, velocity field and other fields related to dynamo processes. In particular, those solutions are obtained with parameters very different from those appropriate for the Earth s core. Geophysical application of the numerical results therefore depends on correct understanding of the differences (errors) between the model outputs and the true states (truth) in the outer core. Part of the truth can be observed at the surface in the form of poloidal magnetic field. To understand these differences, or errors, we generate new initial model state (analysis) by assimilating sequentially the model outputs with the surface geomagnetic observations using an optimal interpolation scheme. The time evolution of the core state is then controlled by our MoSST core dynamics model. The final outputs (forecasts) are then compared with the surface observations as a means to test the success of the assimilation. We use the surface geomagnetic data back to year 1900 for our studies, with 5-year forecast and 20-year analysis periods. We intend to use the result; to understand time variation of the errors with the assimilation sequences, and the impact of the assimilation on other unobservable quantities, such as the toroidal field and the fluid velocity in the core.

Kuang, Weijia↗

Simulated building energy demand biases resulting from the use of representative weather stations

Numerical building models are typically forced with weather data from a limited number of “representative cities” or weather stations representing different climate regions. The use of representative weather stations reduces computational costs, but often fails to capture spatial heterogeneity in weather that may be important for simulations aimed at understanding how building stocks respond to a changing climate. We quantify the potential reduction in bias from using an increasing number of weather stations over the western U.S. The approach is based on deriving temperature and load time series using incrementally more weather stations, ranging from 8 to roughly 150, to capture weather across different seasons. Using 8 stations, one from each climate zone, across the western U.S. results in an average absolute summertime temperature bias of 7.2°F with respect to a spatially-resolved gridded dataset. The mean absolute bias drops to 2.8°F using all available weather stations. Temperature biases of this magnitude could translate to absolute summertime mean simulated load biases as high as 13.8%, a significant error for capacity expansion planners who may use these types of simulations. Increasing the size of the domain over which biases are calculated reduces their magnitude as positive and negative biases may cancel out. Using 8 representative weather stations can lead to a 20-40% overestimation of peak building loads during both summer and winter. Using weather stations close to population centers reduces both mean and peak load biases. This approach could be used by others designing aggregate building simulations to understand the sensitivity to their choice of weather stations used to drive the models.

Burleyson, Casey D.↗

Dynamic responses of submerged components in advanced reactors: experimental and numerical studies

The seismic design of an advanced nuclear reactor must consider the interaction of vessel internal components with the surrounding coolant: fluid–structure interaction (FSI). Available analytical solutions for FSI of submerged components do not accommodate multiple-component, intense seismic inputs and complex reactor and internal geometries. Physical testing of reactor vessels and internals to inform seismic design is impractical and cost-prohibitive, leaving the use of verified and validated, robust numerical models as the only plausible option for analysis and design. Physical data that could be used for validating such numerical models for multi-component shaking are not available. This article describes an experimental program performed on a 6-degree-of-freedom earthquake simulator to generate data that could support validation of seismic FSI numerical models for submerged components in commercial finite element codes. A scaled model of a base-supported reactor vessel with simplified representations of submerged internals was tested to generate submerged-component response histories for a range of seismic inputs. The generated data were used to validate numerical models in the finite element code LS-DYNA. Numerical models were validated for calculation of hydrodynamic pressure responses on internals, in-water frequencies of internals, and acceleration responses of internals. The generated data and the analysis recommendations could aid engineering analysts designing submerged components and systems for seismic effects.

Engineering↗

A Numerical and Experimental Investigation of Flow Separation Control over a Wall-Mounted Hump Model

Numerical simulations and wind tunnel experiments were performed to investigate flow separation and its control over a wall-mounted hump model. Three-dimensional, unsteady fluid dynamic simulations were used to capture the relevant flow physics of unsteady flow separation and its control via active and passive flow control methods. Surface pressure measurements and surface oilflow visualization were obtained in the experiments. Current measurements documented a considerably thinner incoming boundary layer, but similar pressure distribution, compared to the reference data reported in the CFD (Computational Fluid Dynamics) Validation (CFDVAL 2004) Experiments. Consistent with the data available in the literature, numerical simulations predicted a longer separation bubble, which manifested itself as a shift in the pressure distributions. Streamwise vortices generated by passive vortex generators increased the suction pressure and provided substantial pressure recovery. Numerical simulations of vortex generators qualitatively predicted the effects of control, and revealed patterns of attached/separated flow regions. On the other hand, active flow control using steady discrete jets reduced, but was not able to eliminate, flow separation for the tested configuration. Although the major disagreement between the numerical and experimental results was in the pressure recovery region due to the inaccurate prediction of separation bubbles, the relative pressure recoveries from the baselines were comparable. Surface oilflow visualization and simulated surface streamlines were qualitatively in good agreement revealing the key flow features.

Koklu, Mehti↗

A numerical circulation model with topography for the Martian Southern Hemisphere

A quasi-geostrophic numerical model, including friction, radiation, and the observed planetary topography, is applied to the general circulation of the Martian atmosphere in the Southern Hemisphere at latitudes south of about 35 deg. Near equilibrium weather systems developed after about 5 model days. To avoid violating the quasi-geostrophic approximation, only 0.8 of the already smoothed relief was employed. Weather systems and velocity fields are strikingly tied to topography. A 2mb middle latitude jet stream is found of remarkably terrestrial aspect. Highest surface velocities, both horizontal and vertical, are predicted in western Hellas Planitia and eastern Argyre Planitia, which are observed to be preferred sites of origin of major Martian dust storms. Mean horizontal velocities and vertical velocities are found just above the surface velocity boundary layer.

Mass, C.↗

A numerical circulation model with topography for the Martian southern hemisphere

A two-level numerical model taking account of the observed planetary topography is applied to the general circulation of the Martian atmosphere in the southern hemisphere. The physics of this model is based on the assumption of a hydrostatic quasi-geostrophic ideal-gas atmosphere composed entirely of carbon dioxide; radiative transfer among the atmosphere, space, and the ground is included along with surface friction. The calculations indicate the development of near-equilibrium weather systems after about five model days, weather systems and velocity fields whose positions appear to be connected with topography, and a midlatitude jet stream strikingly similar to the terrestrial case. The results also suggest that the vertical and horizontal wind components in western Hellas and eastern Argyre produce copious amounts of suspendible dust each year, that both major and minor dust storms should be a common occurrence on Mars, and that the entire south circumpolar zone appears to be a dust sink in winter.

Mass, C.↗

Equivalent beam modeling using numerical reduction techniques

Numerical procedures that can accomplish model reductions for space trusses were developed. Three techniques are presented that can be implemented using current capabilities within NASTRAN. The proposed techniques accomplish their model reductions numerically through use of NASTRAN structural analyses and as such are termed numerical in contrast to the previously developed analytical techniques. Numerical procedures are developed that permit reductions of large truss models containing full modeling detail of the truss and its joints. Three techniques are presented that accomplish these model reductions with various levels of structural accuracy. These numerical techniques are designated as equivalent beam, truss element reduction, and post-assembly reduction methods. These techniques are discussed in detail.

Chapman, J. M.↗

Determination of the Most Likely Wear Zones of Pipe Bends in the Pulsed Pneumatic Conveyor at the RT-1 Plant

The results of an experimental investigation and numerical modeling of the most likely high-wear zones in 90° pipeline bends in the pulsed pneumatic conveyor system at the RT-1 plant of the Mayak Industrial Association are presented. The experimental studies were conducted on a model of a pulsed pneumatic conveyor system; the numerical modeling of the gas-dynamic flow in the pipeline channel was performed in a model of a two-dimensional non-stationary motion of a compressible medium. It was found on the basis of the experimental results obtained using the model and numerical modeling in the homogeneous approximation that local regions with high wear of walls in the 90° pipe bends in the pulsed pneumatic conveyor do indeed exist and their experimentally found positions agree with the calculations.

42 ENGINEERING↗

A numerical study of process complexity in permafrost dominated regions

Numerical modeling of permafrost dynamics requires adequate representation of atmospheric and surface processes, a reasonable parameter estimation strategy, and site-specific model development. The three main research objectives of the study are: (i) to propose a novel methodology that determines the required level of surface process complexity of permafrost models by conducting parameter sensitivity and calibration, (ii) to design and compare three numerical models of increasing surface process complexity, and (iii) to calibrate and validate the numerical models at the Yakou catchment on the Qinghai-Tibet Plateau as an exemplary study site. The calibration was carried out by coupling the Advanced Terrestrial Simulator (numerical model) and PEST (calibration tool). Simulation results showed that (i) A simple numerical model that considers only subsurface processes can simulate active layer development with the same accuracy as other more complex models that include surface processes. (ii) Peat and mineral soil layer permeability, Van Genuchten alpha, and porosity are highly sensitive. (iii) Liquid precipitation aids in increasing the rate of permafrost degradation. (iv) Deposition of snow insulated the subsurface during the thaw initiation period. We have developed and released an integrated code that couples the numerical software ATS to the calibration software PEST. The numerical model can be further used to determine the impacts of climate change on permafrost degradation.

Calibration↗

Middle Atmosphere Dynamics with Gravity Wave Interactions in the Numerical Spectral Model: Tides and Planetary Waves

As Lindzen (1981) had shown, small-scale gravity waves (GW) produce the observed reversals of the zonal-mean circulation and temperature variations in the upper mesosphere. The waves also play a major role in modulating and amplifying the diurnal tides (DT) (e.g., Waltersheid, 1981; Fritts and Vincent, 1987; Fritts, 1995a). We summarize here the modeling studies with the mechanistic numerical spectral model (NSM) with Doppler spread parameterization for GW (Hines, 1997a, b), which describes in the middle atmosphere: (a) migrating and non-migrating DT, (b) planetary waves (PW), and (c) global-scale inertio gravity waves. Numerical experiments are discussed that illuminate the influence of GW filtering and nonlinear interactions between DT, PW, and zonal mean variations. Keywords: Theoretical modeling, Middle atmosphere dynamics, Gravity wave interactions, Migrating and non-migrating tides, Planetary waves, Global-scale inertio gravity waves.

Mayr, Hans G.↗

On numerical considerations for modeling reactive astrophysical shocks

Simulating detonations in astrophysical environments is often complicated by numerical approximations to shock structure. A common prescription to ensure correct detonation speeds and associated quantities is to prohibit burning inside the numerically broadened shock. We have performed a series of simulations to verify the efficacy of this approximation and to understand how resolution and dimensionality might affect its use. Our results show that in one dimension, prohibiting burning in the shock is important wherever the carbon burning length is not resolved, in keeping with the results of Fryxell et al. In two dimensions, we find that the prohibition of shock burning effectively inhibits the development of cellular structure for all but the most highly resolved cases. We discuss the possible impacts this outcome may have on sub-grid models and detonation propagation in models of Type Ia supernovae, including potential impacts on observables.

79 ASTRONOMY AND ASTROPHYSICS↗

Impact of turbulence modeling on numerical accuracy and efficiency of compressible flow simulations

Discussed is the numerical implementation of turbulence models used in viscous compressible flow simulations and their performance described with respect to numerical accuracy, efficiency and stability. The basic approach utilizes the Reynolds-averaged compressible Navier-Stokes equations in which the Reynolds stresses and heat fluxes are mathematically modeled by suitable turbulence models. The turbulence models investigated include zero-, one-, and two-equation eddy viscosity models. The flow fields investigated include theoretical and supersonic flows about two-dimensional and axisymmetric bodies. Discussions concerning the numerical implementation of models include differencing procedures and boundary conditions used to assume numerical stability and accuracy. Numerical performance is also evaluated by comparing computations with experimental results.

Coakley, Thomas J.↗

Thermal Analysis and Design of Multi-layer Insulation for Re-entry Aerodynamic Heating

The combined radiation/conduction heat transfer in high-temperature multi-layer insulations was modeled using a finite volume numerical model. The numerical model was validated by comparison with steady-state effective thermal conductivity measurements, and by transient thermal tests simulating re-entry aerodynamic heating conditions. A design of experiments technique was used to investigate optimum design of multi-layer insulations for re-entry aerodynamic heating. It was found that use of 2 mm foil spacing and locating the foils near the hot boundary with the top foil 2 mm away from the hot boundary resulted in the most effective insulation design. A 76.2 mm thick multi-layer insulation using 1, 4, or 16 foils resulted in 2.9, 7.2, or 22.2 percent mass per unit area savings compared to a fibrous insulation sample at the same thickness, respectively.

Daryabeigi, Kamran↗