Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “nonlinear structural analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Investigation of difficult component effects on FEM vibration prediction for the AH-1G helicopter

Under the NASA-sponsored Design Analysis Methods for Vibrations program, a series of ground vibration tests and NASTRAN finite element model correlations were conducted on the Bell AH-1G helicopter gunship to investigate the effects of difficult components on the vibration response of the airframe. Secondary structure and damping were found to have significant effects on the frequency response of the airframe above 15 Hz. The nonlinear effects of thrust stiffening and elastomeric mounts on the low-frequency pylon modes below the main rotor were also significant.

Dompka, Robert V.↗
NASA NTRS1995

Direct adaptive performance optimization of subsonic transports: A periodic perturbation technique

Aircraft performance can be optimized at the flight condition by using available redundancy among actuators. Effective use of this potential allows improved performance beyond limits imposed by design compromises. Optimization based on nominal models does not result in the best performance of the actual aircraft at the actual flight condition. An adaptive algorithm for optimizing performance parameters, such as speed or fuel flow, in flight based exclusively on flight data is proposed. The algorithm is inherently insensitive to model inaccuracies and measurement noise and biases and can optimize several decision variables at the same time. An adaptive constraint controller integrated into the algorithm regulates the optimization constraints, such as altitude or speed, without requiring and prior knowledge of the autopilot design. The algorithm has a modular structure which allows easy incorporation (or removal) of optimization constraints or decision variables to the optimization problem. An important part of the contribution is the development of analytical tools enabling convergence analysis of the algorithm and the establishment of simple design rules. The fuel-flow minimization and velocity maximization modes of the algorithm are demonstrated on the NASA Dryden B-720 nonlinear flight simulator for the single- and multi-effector optimization cases.

Espana, Martin D.↗
NASA NTRS1994

Topological analysis of the CfA redshift survey

We study the topology of large-scale structure in the Center for Astrophysics Redshift Survey, which now includes approximately 12,000 galaxies with limiting magnitude m(sub B) is less than or equal to 15.5. The dense sampling and large volume of this survey allow us to compute the topology on smoothing scales from 6 to 20/h Mpc; we thus examine the topology of structure in both 'nonlinear' and 'linear' regimes. On smoothing scales less than or equal to 10/h Mpc this sample has 3 times the number of resolution elements of samples examined in previous studies. Isodensity surface of the smoothed galaxy density field demonstrate that coherent high-density structures and large voids dominate the galaxy distribution. We compute the genus-threshold density relation for isodensity surfaces of the CfA survey. To quantify phase correlation in these data, we compare the CfA genus with the genus of realizations of Gaussian random fields with the power spectrum measured for the CfA survey. On scales less than or equal to 10/h Mpc the observed genus amplitude is smaller than random phase (96% confidence level). This decrement reflects the degree of phase coherence in the observed galaxy distribution. In other words the genus amplitude on these scales is not good measure of the power spectrum slope. On scales greater than 10/h Mpc, where the galaxy distribution is rougly in the 'linear' regime, the genus ampitude is consistent with the random phase amplitude. The shape of the genus curve reflects the strong coherence in the observed structure; the observed genus curve appears broader than random phase (94% confidence level for smoothing scales less than or equal to 10/h Mpc) because the topolgoy is spongelike over a very large range of density threshold. This departre from random phase consistent with a distribution like a filamentary net of 'walls with holes.' On smoothing scales approaching approximately 20/h Mpc the shape of the CfA genus curve is consistent with random phase. There is very weak evidence for a shift of the genus toward a 'bubble-like' topology. To test cosmological models, we compute the genus for mock CfA surveys drawn from large (L greater than or approximately 400/h Mpc) N-body simulations of three variants of the cold dark matter (CDM) cosmogony. The genus amplitude of the 'standard' CDM model (omega h = 0.5, b = 1.5) differs from the observations (96% confidence level) on smoothing scales is less than or approximately 10/h Mpc. An open CDM model (omega h = 0.2) and a CDM model with nonzero cosmological constant (omega h = 0.24, lambda (sub 0) = 0.6) are consistent with the observed genus amplitude over the full range of smoothing scales. All of these models fail (97% confidence level) to match the broadness of the observed genus curve on smoothing scales is less than or equal to 10/h Mpc.

Vogeley, Michael S.↗
NASA NTRS1985

Local strain redistribution corrections for a simplified inelastic analysis procedure based on an elastic finite-element analysis

Strain redistribution corrections were developed for a simplified inelastic analysis procedure to economically calculate material cyclic response at the critical location of a structure for life prediction proposes. The method was based on the assumption that the plastic region in the structure is local and the total strain history required for input can be defined from elastic finite-element analyses. Cyclic stress-strain behavior was represented by a bilinear kinematic hardening model. The simplified procedure predicts stress-strain response with reasonable accuracy for thermally cycled problems but needs improvement for mechanically load-cycled problems. Neuber-type corrections were derived and incorporated in the simplified procedure to account for local total strain redistribution under cyclic mechanical loading. The corrected simplified method was used on a mechanically load-cycled benchmark notched-plate problem. The predicted material response agrees well with the nonlinear finite-element solutions for the problem. The simplified analysis computer program was 0.3% of the central processor unit time required for a nonlinear finite-element analysis.

Kaufman, A.↗
NASA NTRS1976

Some inconsistencies of the finite element method as applied to inelastic response

The inadequacy of a two noded beam-column element with a linear axial and a cubic transverse displacement field for inelastic analysis is demonstrated. For complete equilibrium satisfaction in the linear elastic range a three noded beam-column element is shown to be consistent. Next, the sensitivity of the inelastic response to numerical solutions of the inelastic response of a cantilever beam resulting from approximate integration of strain energy are brought out and finally, consequences of this on the nonlinear transient response of structures are considered.

Kamat, M. P.↗
NASA NTRS1998

A Theoretical and Observational Study of Large and Small-Scale Dynamics in the Mesosphere and Lower Thermosphere in Support of TIMED

The long-term objectives of this IDS component of the TIMED mission are to define, through a combination of modeling and data analysis efforts, the influences of large- and small-scale waves (tidal, planetary, and gravity waves) on the circulation, structure, composition, and variability of the mesosphere and lower thermosphere. Particular emphasis is aimed at the TIMED core science objectives of defining the structure and energetics of the TIMED core region, approx. 60 to 180 km. To do so, however, it is also essential to understand the dynamical influences and contributions because of their considerable direct and indirect influences on structure and energetics. To accomplish these goals, we anticipate two parallel modeling efforts and a significant data analysis effort following TIMED launch. The modeling efforts will address both: the residual circulation response to mean and variable wave forcing of the MLT through development of a spherical model addressing balanced flow dynamics and transience and a more comprehensive effort addressing gravity wave propagation, interactions, nonlinearity, and spectral evolution and transports in canonical and realistic environments. The data analysis effort is envisioned to involve application of ground-based measurements and TIMED data analyses to a quantification of gravity wave forcing and effects at one or more sites with comprehensive measurement suites and extension of the inferred forcing globally, based on distributed ground-based measurements. Research results and publications resulting from the research are included.

Fritts, David C.↗
NASA NTRS2001

Extending unbiased stereology of brain ultrastructure to three-dimensional volumes

OBJECTIVE: Analysis of brain ultrastructure is needed to reveal how neurons communicate with one another via synapses and how disease processes alter this communication. In the past, such analyses have usually been based on single or paired sections obtained by electron microscopy. Reconstruction from multiple serial sections provides a much needed, richer representation of the three-dimensional organization of the brain. This paper introduces a new reconstruction system and new methods for analyzing in three dimensions the location and ultrastructure of neuronal components, such as synapses, which are distributed non-randomly throughout the brain. DESIGN AND MEASUREMENTS: Volumes are reconstructed by defining transformations that align the entire area of adjacent sections. Whole-field alignment requires rotation, translation, skew, scaling, and second-order nonlinear deformations. Such transformations are implemented by a linear combination of bivariate polynomials. Computer software for generating transformations based on user input is described. Stereological techniques for assessing structural distributions in reconstructed volumes are the unbiased bricking, disector, unbiased ratio, and per-length counting techniques. A new general method, the fractional counter, is also described. This unbiased technique relies on the counting of fractions of objects contained in a test volume. A volume of brain tissue from stratum radiatum of hippocampal area CA1 is reconstructed and analyzed for synaptic density to demonstrate and compare the techniques. RESULTS AND CONCLUSIONS: Reconstruction makes practicable volume-oriented analysis of ultrastructure using such techniques as the unbiased bricking and fractional counter methods. These analysis methods are less sensitive to the section-to-section variations in counts and section thickness, factors that contribute to the inaccuracy of other stereological methods. In addition, volume reconstruction facilitates visualization and modeling of structures and analysis of three-dimensional relationships such as synaptic connectivity.

NASA Discipline Neuroscience↗
NASA NTRS1984

A nonlinear structural concept for drag-reducing compliant walls

Two mechanisms of drag reduction for flow over flat plates were investigated. The first mechanism employs Bushnell's hypothesis that compliant walls produce drag reduction by interfering with the formation of the turbulent spots in a turbulent boundary layer. It is shown that the amplitudes and frequencies of compliant wall motions for drag reduction might be achieved by using slightly curved walls and the resulting large amplitude motions of snap buckling. A simple structural model of an arch is used in the analysis, and an asymptotic method is developed. The required wall motions can be obtained by using materials like mylar. In addition, the delay of transition from laminar to turbulent flow by driven walls was studied for Poiseuille channel flow. The walls are driven by a periodic traveling wave. A significant increase in the transitional Reynolds number is obtained by appropriately prescribing the wavelength and phase velocity of the wall motion. Previously developed asymptotic methods are used in the analysis. Previously announced in STAR as N83-11061

Reiss, E. L.↗
NASA NTRS1991

Nonlinear panel flutter in a rarefied atmosphere - Aerodynamic shear stress effects

The panel flutter phenomenon is studied assuming free-molecule flow. This kind of analysis is relevant in the case of hypersonic flight vehicles traveling at high altitudes, especially in the leeward portion of the vehicle. In these conditions the aerodynamic shear can be expected to be considerably larger than the pressure at a given point, so that the effects of such a loading are incorporated into the structural model. This is accomplished by introducing distributed longitudinal and bending moment loads. The former can lead to buckling of the panel, with the second mode in the case of a simply-supported panel playing a important role, and becoming the dominant mode in the solution. The presence of equivalent springs in the longitudinal direction at the panel's ends also becomes of relative importance, even for the evaluation of the linear flutter parameter. Finally, the behavior of the system is studied in the presence of applied compressive forces, that is, classical buckling.

Resende, Hugo B.↗
NASA NTRS1985

On local total strain redistribution using a simplified cyclic inelastic analysis based on an elastic solution

Strain redistribution corrections were developed for a simplified inelastic analysis procedure to economically calculate material cyclic response at the critical location of a structure for life prediction purposes. The method was based on the assumption that the plastic region in the structure is local and the total strain history required for input can be defined from elastic finite element analyses. Cyclic stress-strain behavior was represented by a bilinear kinematic hardening model. The simplified procedure has been found to predict stress-strain response with reasonable accuracy for thermally cycled problems but needs improvement for mechanically load cycled problems. This study derived and incorporated Neuber type corrections in the simplified procedure to account for local total strain redistribution under cyclic mechanical loading. The corrected simplified method was exercised on a mechanically load cycled benchmark notched plate problem. Excellent agreement was found between the predicted material response and nonlinear finite element solutions for the problem. The simplified analysis computer program used 0.3 percent of the CPU time required for a nonlinear finite element analysis.

Hwang, S. Y.↗
NASA NTRS1985

On local total strain redistribution using a simplified cyclic inelastic analysis based on an elastic solution

Strain redistribution corrections were developed for a simplified inelastic analysis procedure to economically calculate material cyclic response at the critical location of a structure for life prediction purposes. The method was based on the assumption that the plastic region in the structure is local and the total strain history required for input can be defined from elastic finite element analyses. Cyclic stress-strain behavior was represented by a bilinear kinematic hardening model. The simplified procedure has been found to predict stress-strain response with reasonable accuracy for thermally cycled problems but needs improvement for mechanically load cycled problems. This study derived and incorporated Neuber type corrections in the simplified procedure to account for local total strain redistribution under cyclic mechanical loading. The corrected simplified method was exercised on a mechanically load cycled benchmark notched plate problem. Excellent agreement was found between the predicted material response and nonlinear finite element solutions for the problem. The simplified analysis computer program used 0.3 percent of the CPU time required for a nonlinear finite element analysis.

Hwang, S. Y.↗
NASA NTRS1974

Nonlinear panel response by a Monte Carlo approach

The vibration of clamped and simply supported elastic panels due to subsonic and supersonic turbulent boundary-layer flows is investigated by a Monte Carlo technique. The resulting generalized random forces are simulated numerically from boundary-layer turbulence spectra, and the response analysis is performed in the time domain. The mutual interaction between panel motion and external and/or internal airflow is included. Response studies are performed with respect to rms response, probability structure, peak distribution, threshold crossing and spectral density. The effect on the response statistics of in-plane loading, static pressure differential, and cavity pressure is investigated.

Vaicaitis, R.↗
NASA NTRS1976

Aeroelastic characteristics of composite bearingless rotor blades

Owing to the inherent unique structural features of composite bearingless rotors, various assumptions upon which conventional rotor aeroelastic analyses are formulated, are violated. Three such features identified are highly nonlinear and time-varying structural twist, structural redundancy in bending and torsion, and for certain configurations a strongly coupled low frequency bending-torsion mode. An examination of these aeroelastic considerations and appropriate formulations required for accurate analyses of such rotor systems is presented. Also presented are test results from a dynamically scaled model rotor and complementary analytic results obtained with the appropriately reformulated aeroelastic analysis.

Bielawa, R. L.↗
NASA NTRS1981

Determination of model structure and parameters of an airplane from pre- and post-stall flight data

A procedure for airplane model structure determination from flight data based on modified stepwise regression (MSR), several decision criteria and postulated aerodynamic model equations is presented. The MSR is constructed to force a linear model for the aerodynamic coefficient first, then select significant nonlinear terms and reject nonsignificant terms from the model. In addition to the statistical criteria in the stepwise regression, the prediction sum of squares (PRESS) criterion and analysis of residuals are examined for the selection of an adequate model. The procedure is used in examples with simulated and real flight data. It is shown that the MSR performs better than the ordinary stepwise regression and that the technique can be also applied to the large amplitude maneuvers.

Klein, V.↗
NASA NTRS1981

Helicopter vibration suppression using simple pendulum absorbers on the rotor blade

A design procedure is presented for the installation of simple pendulums on the blades of a helicopter rotor to suppress the root reactions. The procedure consists of a frequency response analysis for a hingeless rotor blade excited by a harmonic variation of spanwise airload distributions during forward flight, as well as a concentrated load at the tip. The structural modeling of the blade provides for elastic degrees of freedom in flap and lead-lag bending plus torsion. Simple flap and lead-lag pendulums are considered individually. Using a rational order scheme, the general nonlinear equations of motion are linearized. A quasi-steady aerodynamic representation is used in the formation of the airloads. The solution of the system equations derives from their representation as a transfer matrix. The results include the effect of pendulum tuning on the minimization of the hub reactions.

Hamouda, M.-N. H.↗
NASA NTRS1984

Rotordynamic Characteristics of the HPOTP (High Pressure Oxygen Turbopump) of the SSME (Space Shuttle Main Engine)

Rotational stability of turbopump components in the space shuttle main engine was studied via analysis of component and structural dynamic models. Subsynchronous vibration caused unacceptable migration of the rotor/housing unit with unequal load sharing of the synchronous bearings that resulted in the failure of the High Pressure Oxygen Turbopump. Linear analysis shows that a shrouded inducer eliminates the second critical speed and the stability problem, a stiffened rotor improves the rotordynamic characteristics of the turbopump, and installing damper boost/impeller seals reduces bearing loads. Nonlinear analysis shows that by increasing the "dead band' clearances, a marked reduction in peak bearing loads occurs.

Childs, D. W.↗
NASA NTRS1989

Three-dimensional thermal convection in a spherical shell

Nonlinear convective solutions are presented for a shell with properties characteristic of the earth's whole mantle for Rayleigh numbers up to 70,000. The solutions are validated numerically, and two distinct convective patterns (cubic and tetrahedral) are identified which are closely related to the geometric planforms predicted by the analytical theories of slightly supercritical spherical convection. A quantitative analysis of the horizontal and vertical structures of the velocity and temperature fields of the solutions is presented, and their heat transport properties are examined, including the total heat flow and the spatial distribution of the heat flux at the shell boundaries.

Bercovici, D.↗
NASA NTRS2004

Analysis of SMA Hybrid Composite Structures using Commercial Codes

A thermomechanical model for shape memory alloy (SMA) actuators and SMA hybrid composite (SMAHC) structures has been recently implemented in the commercial finite element codes MSC.Nastran and ABAQUS. The model may be easily implemented in any code that has the capability for analysis of laminated composite structures with temperature dependent material properties. The model is also relatively easy to use and requires input of only fundamental engineering properties. A brief description of the model is presented, followed by discussion of implementation and usage in the commercial codes. Results are presented from static and dynamic analysis of SMAHC beams of two types; a beam clamped at each end and a cantilevered beam. Nonlinear static (post-buckling) and random response analyses are demonstrated for the first specimen. Static deflection (shape) control is demonstrated for the cantilevered beam. Approaches for modeling SMAHC material systems with embedded SMA in ribbon and small round wire product forms are demonstrated and compared. The results from the commercial codes are compared to those from a research code as validation of the commercial implementations; excellent correlation is achieved in all cases.

Turner, Travis L.↗