Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “generative diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

BRDF Calibration of Sintered PTFE in the SWIR

Satellite instruments operating in the reflective solar wavelength region often require accurate and precise determination of the Bidirectional Reflectance Distribution Function (BRDF) of laboratory-based diffusers used in their pre-flight calibrations and ground-based support of on-orbit remote sensing instruments. The Diffuser Calibration Facility at NASA's Goddard Space Flight Center is a secondary diffuser calibration standard after NEST for over two decades, providing numerous NASA projects with BRDF data in the UV, Visible and the NIR spectral regions. Currently the Diffuser Calibration Facility extended the covered spectral range from 900 nm up to 1.7 microns. The measurements were made using the existing scatterometer by replacing the Si photodiode based receiver with an InGaAs-based one. The BRDF data was recorded at normal incidence and scatter zenith angles from 10 to 60 deg. Tunable coherent light source was setup. Broadband light source application is under development. Gray-scale sintered PTFE samples were used at these first trials, illuminated with P and S polarized incident light. The results are discussed and compared to empirically generated BRDF data from simple model based on 8 deg directional/hemispherical measurements.

Georgiev, Georgi T.↗

The generation of magnetic fields in astrophysical bodies. X - Magnetic buoyancy and the solar dynamo

The magnetic field appearing as bipolar magnetic regions at the surface of the sun represents the lines of force from a general azimuthal field of the order of 100 gauss somewhere beneath the surface. The amplification time, as a consequence of the nonuniform rotation, is of the order of 10 years. But magnetic buoyancy brings the azimuthal field up through much of the convective zone in a time rather less than 10 years, raising the question of where the azimuthal field can be retained long enough to be amplified. We show that magnetic fields can be retained for long periods of time in the stable radiative region beneath the convective zone, but unfortunately the solar dynamo cannot function there because turbulent diffusion is an essential part of its operation. The only possible conclusion appears to be that the dynamo operates principally in the very lowest levels of the convective zone at depths of 150,000 km or more, where the gas density is 0.1 g/cu cm, and the fields are limited to 50 gauss.

Parker, E. N.↗

Non-steady Reconnection in Global Simulations of Magnetosphere Dynamics

To analyze the non-steady magnetic reconnection during quasi-steady solar wind driving we employed high resolution global MHD model BATSRUS with non-MHD corrections in diffusion regions around the reconnection sites. To clarify the role of small-scale non-MHD effects on the global magnetospheric dynamic we performed simulations with different models of dissipation. We found that magnetopause surface is not in steady state even during extended periods of steady solar wind conditions. The so-called tilted reconnection lines become unstable due to formation of pressure bubbles, strong core field flux tubes, vortices, and traveling magnetic field cavities. Non-steady dayside reconnection results in formation of flux tubes with bended axis magnetically connecting magnetic field cavities generated at flanks and strong core segments formed near the subsolar region. We found that the rate of magnetic flux loading to the tail lobes is not very sensitive to the dissipation mechanism and details of the dayside reconnection. On the other hand the magnetotail reconnection rate, the speed of the reconnection site retreat and the global magnetotail dynamics strongly depend on the model of dissipation. THEMIS and Cluster observations are consistent with signatures predicted by simulations.

Kuznetsova, M. M.↗

Taking the Pulse of PyroCumulus Clouds

Forest fires can burn large areas, but can also inject smoke into the upper troposphere/lower stratosphere (UT/LS), where stakes are even higher for climate, because emissions tend to have a longer lifetime, and can produce significant regional and even global climate effects, as is the case with some volcanoes. Large forest fires are now believed to be more common in summer, especially in the boreal regions, where pyrocumulus (pyroCu), and occasionally pyrocumuionimbus (pyroCb) clouds are formed, which can transport emissions into the UT/LS. A major difficulty in developing realistic fire plume models is the lack of observational data within fire plumes that resolves structure at a few 100 m scales, which can be used to validate these models. Here, we report detailed airborne radiation measurements within strong pyroCu taken over boreal forest fires in Saskatchewan, Canada during the Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS) summer field campaign in 2008. We find that the angular distribution of radiance within the pyroCu is closely related to the diffusion domain in water clouds and can be described by very similar simple cosine functions. We demonstrate with Monte Carlo simulations that radiation transport in pyroCu is inherently a 3D phenomenon and must account for particle absorption. However, the simple cosine function promises to offer an easy solution for climate models. The presence of a prominent smoke core, defined by strong extinction in the UV, VIS and NIR, suggests that the core might be an important pathway for emission transport to the upper troposphere and lower stratosphere. We speculate that this plume injection core is generated and sustained by complex processes not yet well understood, but not necessarily related directly to the intense fires that originally initiated the plume rise.

Gatebe, C. K.↗

Stall-Departure-Resistance Enhancer

Stall-departure-resistance enhancer imposes lesser drag penalty than nortex generators of older types. Increases lift by as much as 30 percent at angles of attack otherwise in poststall region. Device is flat plate wedge with 60 degree sweep angle and attached so it protrudes from leading edge of wing. Tip is sharp point, and edges made thin and sharp to induce good vortical flow. Applications include those intended to increase safety for broad range of aircraft, including trainers, fighters, general-aviation aircraft, and commercial transport aircraft. Nonaerospace applications where flow stall is problem under certain conditions, such as in control of separation in flow diffusers. Other applications in fluid machinery and fluid flow.

Ross, Holly M.↗

An XMM-Newton Study of 9SGR and the Lagoon Nebula

We report preliminary results of an XMM-Newton observation of the 04 V star 9 Sgr (= HD 164794). 9 Sgr is one of a few single OB stars that display a non-thermal radio emission attributed to synchrotron emission by relativistic electrons. Inverse Compton scattering of photospheric UV photons by these relativistic electrons is a priori expected to generate a non-thermal power-law tail in the X-ray spectrum. Our EPIC and RGS spectra of 9 Sgr suggest a more complex situation than expected from this 'simple' theoretical picture. Furthermore, soft-band EPIC images of the region around 9 Sgr reveal a number of point sources inside the Lagoon Nebula (M8). Most of these sources have optical counterparts inside the very young open cluster NGC 6530 and several X-ray sources are associated with low and intermediate mass pre-main sequence stars. Finally, we also detect (probably) diffuse X-ray emission from the Hourglass Region that might reveal a hot bubble blown by the stellar wind of Herschel 36, the ionizing star of the HG region.

Rauw, G.↗

The Light of the Night Sky in EUSO: Duty Cycle and Background

The EUSO detector, which will be installed on the International Space Station, will detect the light produced by the EAS generated by the UHECR when entering the Earth's atmosphere. The EUSO telescope will operate only during dark night. The light background in the EUSO detector is of outmost importance. To determine the detector duty cycle, it is necessary to know the periods in which it will be in the obscurity, taking into account both sun and moon precise ephemerides and the ISS trajectory. For signal to background determination and trigger efficiency study, the photon background has to be evaluated, taking into account the various UV light sources at night: natural sources as airglow, stars and diffuse light of the night sky, and artificial sources.

Adams, J.↗

Lower-Hybrid Wave Structures and Interactions With Electrons Observed in Magnetotail Reconnection Diffusion Regions

We investigate waves close to the lower-hybrid frequency in 12 magnetotail reconnection electron diffusion region (EDR) events with guide field levels of near-zero to 30%. In about half of the events, the wave vector has a small component along the current sheet normal, consistent with known lower-hybrid drift wave properties, but the perpendicular magnetic field fluctuations can be comparable or greater than the parallel component, a feature unique to the waves inside and adjacent to EDRs. Another new wave property is that the wave vector has a significant component along the current sheet normal in some events and completely along the normal for one event. In 1/4of the events, the ∇∙𝑷(sub 𝑒) term has a significant contribution to the wave electric field, possibly a feature of lower-hybrid waves more likely to exist in the diffusion region than further away from the X-line. Electron temperature variations are correlated with the wave potential, due to wave electric field acceleration and crossings at the corrugated separatrix region with different amounts of mixing between reconnection inflowing and outflowing populations. The latter also leads to the anti-correlation between parallel and perpendicular temperature components. Using four-spacecraft measurements, the magnetic field line twisting is demonstrated by the correlated fluctuations in (∇×𝑽(sub 𝐸×𝐵))||and (∇×𝐁)||. The lower-hybrid wave in the EDR of weak guide field reconnection may be generated near separatrices and penetrate to the mid-plane or locally generated, and the latter possibility is beyond the prediction of previous reconnection simulations.

Magnetic reconnection↗

Simulation of 2-dimensional viscous flow through cascades using a semi-elliptic analysis and hybrid C-H grids

A semi-elliptic formulation, termed the interacting parabolized Navier-Stokes (IPNS) formulation, is developed for the analysis of a class of subsonic viscous flows for which streamwise diffusion is neglible but which are significantly influenced by upstream interactions. The IPNS equations are obtained from the Navier-Stokes equations by dropping the streamwise viscous-diffusion terms but retaining upstream influence via the streamwise pressure-gradient. A two-step alternating-direction-explicit numerical scheme is developed to solve these equations. The quasi-linearization and discretization of the equations are carefully examined so that no artificial viscosity is added externally to the scheme. Also, solutions to compressible as well as nearly compressible flows are obtained without any modification either in the analysis or in the solution process. The procedure is applied to constricted channels and cascade passages formed by airfoils of various shapes. These geometries are represented using numerically generated curilinear boundary-oriented coordinates forming an H-grid. A hybrid C-H grid, more appropriate for cascade of airfoils with rounded leading edges, was also developed. Satisfactory results are obtained for flows through cascades of Joukowski airfoils.

Ramamurti, R.↗

Multiple Mode Actuation of a Turbulent Jet

The effects of multiple mode periodic excitation on the evolution of a circular turbulent jet were studied experimentally. A short, wide-angle diffuser was attached to the jet exit. Streamwise and cross-stream excitations were introduced at the junction between the jet exit and the diffuser inlet on opposing sides of the jet. The introduction of high amplitude, periodic excitation in the streamwise direction enhances the mixing and promotes attachment of the jet shear-layer to the diffuser wall. Cross-stream excitation applied over a fraction of the jet circumference can deflect the jet away from the excitation slot. The two modes of excitation were combined using identical frequencies and varying the relative phase between the two actuators in search of an optimal response. It is shown that, for low and moderate periodic momentum input levels, the jet deflection angles depend strongly on the relative phase between the two actuators. Optimum performance is achieved when the phase difference is pi +/- pi/6. The lower effectiveness of the equal phase excitation is attributed to the generation of an azimuthally symmetric mode that does not produce the required non-axisymmetric vectoring. For high excitation levels, identical phase becomes more effective, while phase sensitivity decreases. An important finding was that with proper phase tuning, two unsteady actuators can be combined to obtain a non-linear response greater than the superposition of the individual effects.

Pack, LaTunia G.↗

Multiple Mode Actuation of a Turbulent Jet

The effects of multiple mode periodic excitation on the evolution of a circular turbulent jet were studied experimentally. A short, wide-angle diffuser was attached to the jet exit. Streamwise and cross-stream excitations were introduced at the junction between the jet exit and the diffuser inlet on opposing sides of the jet. The introduction of high amplitude, periodic excitation in the streamwise direction enhances the mixing and promotes attachment of the jet shear-layer to the diffuser wall. Cross-stream excitation applied over a fraction of the jet circumference can deflect the jet away from the excitation slot. The two modes of excitation were combined using identical frequencies and varying the relative phase between the two actuators in search of an optimal response. It is shown that, for low and moderate periodic momentum input levels, the jet deflection angles depend strongly on the relative phase between the two actuators. Optimum performance is achieved when the phase difference is pi +/- pi/6. The lower effectiveness of the equal phase excitation is attributed to the generation of an azimuthally symmetric mode that does not produce the required non-axisymmetric vectoring. For high excitation levels, identical phase becomes more effective, while phase sensitivity decreases. An important finding was that with proper phase tuning, two unsteady actuators can be combined to obtain a non-linear response greater than the superposition of the individual effects.

Pack, LaTunia G.↗

Navier-Stokes analysis of cold scramjet-afterbody flows

The progress of two efforts in coding solutions of Navier-Stokes equations is summarized. The first effort concerns a 3-D space marching parabolized Navier-Stokes (PNS) code being modified to compute the supersonic mixing flow through an internal/external expansion nozzle with multicomponent gases. The 3-D PNS equations, coupled with a set of species continuity equations, are solved using an implicit finite difference scheme. The completed work is summarized and includes code modifications for four chemical species, computing the flow upstream of the upper cowl for a theoretical air mixture, developing an initial plane solution for the inner nozzle region, and computing the flow inside the nozzle for both a N2/O2 mixture and a Freon-12/Ar mixture, and plotting density-pressure contours for the inner nozzle region. The second effort concerns a full Navier-Stokes code. The species continuity equations account for the diffusion of multiple gases. This 3-D explicit afterbody code has the ability to use high order numerical integration schemes such as the 4th order MacCormack, and the Gottlieb-MacCormack schemes. Changes to the work are listed and include, but are not limited to: (1) internal/external flow capability; (2) new treatments of the cowl wall boundary conditions and relaxed computations around the cowl region and cowl tip; (3) the entering of the thermodynamic and transport properties of Freon-12, Ar, O, and N; (4) modification to the Baldwin-Lomax turbulence model to account for turbulent eddies generated by cowl walls inside and external to the nozzle; and (5) adopting a relaxation formula to account for the turbulence in the mixing shear layer.

Baysal, Oktay↗

Molecular flow venting of a volume with an outgassing or desorbing source

A venting equation commonly used to describe the transient evolution of pressure within a volume containing an outgassing or offgassing source and a restrictive vent conductance under conditions of molecular flow has been solved analytically. Solutions are found for sources of finite thickness characterized by classical diffusion-limited behavior (proportional to inverse square root of time), as well as responses for thick material sources often observed in testing that are characterized by a more general form of power-law decay, up to inverse time behavior associated with surface desorption. Solutions involve evaluating integrals where both numerators and denominators of the integrands diverge with time, making wide-ranging transient solutions difficult to directly compute numerically. Usually, one can avoid evaluating these integrals by assuming quasistatic conditions at long time scales. A novel approach is used in this work to analytically produce solutions by generating bespoke mathematical functions, some of which solve integrals that have apparently had no previous analytical solution.

Michael Woronowicz↗

Molecular flow venting of a volume with an outgassing or desorbing source

"A venting equation commonly used to describe the transient evolution of pressure within a volume containing an outgassing or offgassing source and a restrictive vent conductance under conditions of molecular flow has been solved analytically. Solutions are found for sources of finite thickness characterized by classical diffusion-limited behavior (proportional to inverse square root of time), as well as responses for thick material sources often observed in testing that are characterized by a more general form of power-law decay, up to inverse time behavior associated with surface desorption. Solutions involve evaluating integrals where both numerators and denominators of the integrands diverge with time, making wide-ranging transient solutions difficult to directly compute numerically. Usually, one can avoid evaluating these integrals by assuming quasistatic conditions at long time scales. A novel approach is used in this work to analytically produce solutions by generating bespoke mathematical functions, some of which solve integrals that have apparently had no previous analytical solution."

Michael Woronowicz↗

Effects of multiple scattering and surface albedo on the photochemistry of the troposphere

The effect of treatment of incoming solar radiation on the photochemistry of the troposphere is discussed. A one dimensional photochemical model of the troposphere containing the species of the nitrogen, oxygen, carbon, hydrogen, and sulfur families was developed. The vertical flux is simulated by use of the parameterized eddy diffusion coefficients. The photochemical model is coupled to a radiative transfer model that calculates the radiation field due to the incoming solar radiation which initiates much of the photochemistry of the troposphere. Vertical profiles of tropospheric species were compared with the Leighton approximation, radiative transfer, matrix inversion model. The radiative transfer code includes the effects of multiple scattering due to molecules and aerosols, pure absorption, and surface albedo on the transfer of incoming solar radiation. It is indicated that significant differences exist for several key photolysis frequencies and species number density profiles between the Leighton approximation and the profiles generated with, radiative transfer, matrix inversion technique. Most species show enhanced vertical profiles when the more realistic treatment of the incoming solar radiation field is included

Augustsson, T. R.↗

Infrared measurements of spacecraft glow planned for Spacelab 2

A liquid helium cooled infrared telescope (IRT) was to be flown in July 1985 on Spacelab 2. The instrument is designed to measure both diffuse and discrete infrared astronomical sources, including the zodiacal light, galactic, and extragalactic components, as well as to evaluate the induced Orbiter environment. The focal plane contains ten photoconductive detectors covering six broad bands from 2 to 120 microns. Each detector has a 0.5 by 1.0 deg field of view optimized for detection of extended sources of IR radiation. Except for the 2 micron detector, the system noise is limited by the sky background noise. The measurements planned for the IRT use the 1 meter base of the Plasma Diagnostic Package (PDP), an already existing SL 2 experiment, as the glow generating surface. The measurements are repeated changing the position of the PDP, the attitude of the Orbiter, and the ram direction in an effort to remove both the thermal component of the PDP emission and the cosmic background radiation.

Fazio, G. G.↗

COBE's search for structure in the Big Bang

The launch of Cosmic Background Explorer (COBE) and the definition of Earth Observing System (EOS) are two of the major events at NASA-Goddard. The three experiments contained in COBE (Differential Microwave Radiometer (DMR), Far Infrared Absolute Spectrophotometer (FIRAS), and Diffuse Infrared Background Experiment (DIRBE)) are very important in measuring the big bang. DMR measures the isotropy of the cosmic background (direction of the radiation). FIRAS looks at the spectrum over the whole sky, searching for deviations, and DIRBE operates in the infrared part of the spectrum gathering evidence of the earliest galaxy formation. By special techniques, the radiation coming from the solar system will be distinguished from that of extragalactic origin. Unique graphics will be used to represent the temperature of the emitting material. A cosmic event will be modeled of such importance that it will affect cosmological theory for generations to come. EOS will monitor changes in the Earth's geophysics during a whole solar color cycle.

Soffen, Gerald↗

Combustion Processes in Hybrid Rocket Engines

In recent years, there has been a resurgence of interest in the development of hybrid rocket engines for advanced launch vehicle applications. Hybrid propulsion systems use a solid fuel such as hydroxyl-terminated polybutadiene (HTPB) along with a gaseous/liquid oxidizer. The performance of hybrid combustors depends on the convective and radiative heat fluxes to the fuel surface, the rate of pyrolysis in the solid phase, and the turbulent combustion processes in the gaseous phases. These processes in combination specify the regression rates of the fuel surface and thereby the utilization efficiency of the fuel. In this paper, we employ computational fluid dynamics (CFD) techniques in order to gain a quantitative understanding of the physical trends in hybrid rocket combustors. The computational modeling is tailored to ongoing experiments at Penn State that employ a two dimensional slab burner configuration. The coordinated computational/experimental effort enables model validation while providing an understanding of the experimental observations. Computations to date have included the full length geometry with and with the aft nozzle section as well as shorter length domains for extensive parametric characterization. HTPB is sed as the fuel with 1,3 butadiene being taken as the gaseous product of the pyrolysis. Pure gaseous oxygen is taken as the oxidizer. The fuel regression rate is specified using an Arrhenius rate reaction, which the fuel surface temperature is given by an energy balance involving gas-phase convection and radiation as well as thermal conduction in the solid-phase. For the gas-phase combustion, a two step global reaction is used. The standard kappa - epsilon model is used for turbulence closure. Radiation is presently treated using a simple diffusion approximation which is valid for large optical path lengths, representative of radiation from soot particles. Computational results are obtained to determine the trends in the fuel burning or regression rates as a function of the head-end oxidizer mass flux, G=rho(e)U(e), and the chamber pressure. Furthermore, computation of the full slab burner configuration has also been obtained for various stages of the burn. Comparisons with available experimental data from small scale tests conducted by General Dynamics-Thiokol-Rocketdyne suggest reasonable agreement in the predicted regression rates. Future work will include: (1) a model for soot generation in the flame for more quantitative radiative transfer modelling, (2) a parametric study of combustion efficiency, and (3) transient calculations to help determine the possible mechanisms responsible for combustion instability in hybrid rocket motors.

Venkateswaran,S.↗