SEARCH · Engineering Papers

Results for “fractionalization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

All sources NASA NTRS DOE OSTI

NASA NTRS1990

The mechanisms of dispersion strengthening and fracture in Al-based XD(tm) alloys, part 1

The influence of reinforcement size, volume fraction, and matrix deformation behavior on room and elevated temperature strength; the fracture toughness; and the fatigue crack growth rate of metal matrix composites of Al-4(pct)Cu-1.5(pct)Mg with TiB2 were examined. The influence of reinforcement volume fraction was also examined for pure aluminum with TiB2. Higher TiB2 volume fractions increased the tensile yield strength at both room and elevated temperatures, and reduced the elongation to fracture. Tensile tests also indicate that small particles provided a greater increase in strength for a given volume fraction than larger particles, whereas elongation to fracture appeared to be insensitive to reinforcement size. Interparticle spacing appears to be the factor that controls the strength of these alloys, with the exact nature of the dependence relying on the nature of dislocation slip in the matrix (planar vs. diffuse). The isothermal aging response of the precipitation strengthened Al-4(pct)Cu-1.5(pct)Mg alloys was not accelerated by the presence of TiB2. Cold work prior to artificial aging created additional geometrically necessary dislocations which serve as heterogeneous nucleation sites leading to accelerated aging, a finer precipitate size, and an increase in the strength of the alloy.

Aikin, R. M., Jr.↗

NASA NTRS1991

The effect of clouds on the earth's radiation budget

The radiative fluxes from the Earth Radiation Budget Experiment (ERBE) and the cloud properties from the International Satellite Cloud Climatology Project (ISCCP) over Indonesia for the months of June and July of 1985 and 1986 were analyzed to determine the cloud sensitivity coefficients. The method involved a linear least squares regression between co-incident flux and cloud coverage measurements. The calculated slope is identified as the cloud sensitivity. It was found that the correlations between the total cloud fraction and radiation parameters were modest. However, correlations between cloud fraction and IR flux were improved by separating clouds by height. Likewise, correlations between the visible flux and cloud fractions were improved by distinguishing clouds based on optical depth. Calculating correlations between the net fluxes and either height or optical depth segregated cloud fractions were somewhat improved. When clouds were classified in terms of their height and optical depth, correlations among all the radiation components were improved. Mean cloud sensitivities based on the regression of radiative fluxes against height and optical depth separated cloud types are presented. Results are compared to a one-dimensional radiation model with a simple cloud parameterization scheme.

Ziskin, Daniel↗

NASA NTRS1992

Development of a contact lens quality monitoring system

The quality of contact lens samples depends strongly on their free volume fractions. It is expected that the free volume fraction of the test samples will also impact their attenuation coefficients for soft x rays. Samples with larger free volume fractions should have lower linear attenuation coefficients. Linear attenuation coefficients for Cd-109/Ag-109 x rays have been measured in five contact lens samples. It has been shown that the difference in the linear attenuation coefficients of discs from any given sample are entirely due to the difference in their respective volume fractions. It is therefore concluded that an x ray attenuation measurement system can serve as a quality monitor for contact lens polymers.

Singh, Jag J.↗

NASA NTRS1992

Linear mixing model applied to coarse resolution satellite data

A linear mixing model typically applied to high resolution data such as Airborne Visible/Infrared Imaging Spectrometer, Thematic Mapper, and Multispectral Scanner System is applied to the NOAA Advanced Very High Resolution Radiometer coarse resolution satellite data. The reflective portion extracted from the middle IR channel 3 (3.55 - 3.93 microns) is used with channels 1 (0.58 - 0.68 microns) and 2 (0.725 - 1.1 microns) to run the Constrained Least Squares model to generate fraction images for an area in the west central region of Brazil. The derived fraction images are compared with an unsupervised classification and the fraction images derived from Landsat TM data acquired in the same day. In addition, the relationship betweeen these fraction images and the well known NDVI images are presented. The results show the great potential of the unmixing techniques for applying to coarse resolution data for global studies.

Holben, Brent N.↗

NASA NTRS1992

Beneficiation of ilmenite from lumar analog

The results reported were obtained on a meteoric eucrite sample called Millbillillie Sample no. 173. Optical microscopy studies of the sample showed it to consist of ilmenite, troilite, and transparent gangue. The transparent gangue consisted of feldspar (anorthite), pyroxenes, olivines, and opaques. Troilite was present in minor quantities. Screen assay analyses of the 30, 100, 200, and 400 US mesh screen fractions showed that minor concentration of titanium occurred in the 200 x 400 and -400 mesh screen fractions. Scanning electron microscopy (SEM) studies of the bulk sample showed the presence of a variety of ilmenite grains, ranging from 50 microns down to less than 1 micron without any evidence of liberation. Electron Diffraction Scans (EDS) confirmed the ratio of Fe to Ti in the ilmenite grains. Dry magnetic separation in a Frantz Isodynamic Separator was found to be effective only at sizes finer than 150 microns (100 US mesh) and more so at 200 mesh (74 microns). In each case, dedusting of the sample to remove -400 mesh (-0.037 microns) fines was required. Liberation size was determined to be 200 mesh and finer. The highest grade concentrate assaying 3.45 percent Ti was produced by magnetic separation of the -200 + 400 mesh screen fraction assaying 0.44 Ti (from a -30 mesh sample) at a current setting of 0.35 AMP. This concentrate contained 21.2 percent of the Ti values in the screen fraction with 2.72 weight percent of feed to test. The results can be projected to a sample stage ground to -200 mesh. Magnetic separation of the 200 + 400 mesh (-0.074 + 0.037 microns) should produce a concentrate accounting for 1.41 weight percent of the feed. This concentrate will analyze 3.45 percent Ti and contain 10.3 percent of the Ti values in the feed. By changing the Frantz Magnetic Separator settings, a lower grade concentrate analyzing 0.98 percent Ti can be produced at an increased recovery of 25.4 percent. The concentrate weight will be 11.7 percent of the feed. It must be emphasized that improved grades and recoveries can be obtained with the -400 mesh fines. However, beneficiation of these extremely fine materials is not possible in a practical process scheme.

Ramadorai, G.↗

NASA NTRS1992

Magnetic beneficiation of lunar soils

We will present a review of recent laboratory results obtained in dry magnetic separation of one gram samples of the minus 1 mm size fraction of five lunar soils of widely differing maturities. Two highland soils were investigated as potential sources of low iron content feed stocks for space manufacture of metals, including aluminum, silicon, and calcium. Pure anorthite was separated from the diamagnetic fraction of immature highland regolith. Three high titanium mare soils were investigated as potential sources of ilmenite for production of hydrogen and for recovery of He-3. Ilmenite and pyroxene were separated from the paramagnetic fractions of the mare basalts. Agglutinates and other fused soil components containing metallic iron were separated from the strongly magnetic fractions of all soils. We will present conceptual magnetic separation flow sheets developed from the laboratory data and designed for production of anorthite from highland soils and for production of ilmenite from mare soils. Using these flow sheets, we will discuss problems and opportunities associated with the magnetic separation of lunar soils. Separation of high-grade anorthite or other diamagnetic components at moderately high recovery can be achieved in processing immature highland soils. Further, while magnet weight is always an issue in magnetic separation technology, recent developments in both low temperature and high temperature superconductivity present unusual opportunities for magnet design specific to the lunar environment.

Mckay, D. S↗

NASA NTRS1992

The effect of cloud type on earth's energy balance - Results for selected regions

International Satellite Cloud Climatology Project (ISCCP) C1 cloud information is compared with planetary albedo, outgoing longwave radiation (OLR), and net radiation measured at the top of the atmosphere by the Earth Radiation Budget Experiment (ERBE). Principal component analysis indicates that the day-to-day variations of the abundances of the 35 cloud types of the C1 data are correlated with each other, so that for many purposes the data set can be well represented by about five cloud types. Using stepwise multiple regression, the ISCCP C1 data can be used to predict the day-to-day variations of the energy balance measured by ERBE for 2.5-deg regions. Total fractional area coverage of cloudiness is a relatively poor predictor of radiation budget quantities. If the total fractional area coverage by clouds is divided into contributions from several distinct cloud types, the fractional coverages by these several cloud types will together form a much better prediction of radiation budget quantities than the single variable of total fractional-area cloud coverage. The regression equations can be used to estimate the net effect of clouds on the radiation balance and the contributions from particular types of clouds to albedo, OLR, and net radiation.

Ockert-Bell, Maureen E.↗

NASA NTRS1992

The mass balance of soil evolution on late Quaternary marine terraces, northern California

Mass-balance interpretation of a soil chronosequence provides a means of quantifying elemental addition, removal, and transformation that occur in soils from a flight of marine terraces in northern California. Six soil profiles that range in age from several to 240,000 yr are developed in unconsolidated, sandy-marine, and eolian parent material deposited on bedrock marine platforms. Soil evolution is dominated by (1) open-system depletion of Si, Ca, Mg, K, and Na; (2) open-system enrichment of P in surface soil horizons; (3) relative immobility of Fe and Al; and (4) transformation of Fe, Si, and Al in the parent material to secondary clay minerals and sesquioxides. Net mass losses of bases and Si are generally uniform with depth and substantial, in some cases approaching 100 percent; however, the rate of loss of each element differs markedly, causing the ranking of each by relative abundance to shift with time. Loss of Si from the sand fraction by dissolution and particle-size diminution, from about 100 percent to less than 35 percent over 240 ky, mirrors a similar gain in the silt and clay size fractions. The Fe originally present in the sand fraction decreases from greater than 80 percent to less than 10 percent, whereas the amount of Fe present in the clay and crystalline oxyhydroxide fractions increases to 25 percent and 70 percent, respectively.

Merritts, Dorothy J.↗

NASA NTRS1993

Separation of spallation and terrestrial C-14 in chondrites

Weathering products and contamination severely hamper our ability to accurately measure the C-14 spallation component in meteorites, but can give insights into a sample's terrestrial history. A procedure was developed to measure the C-14 in these components using CO and CO2 separations from temperature extractions from 200-500 mg of material. The Bruderheim (L6) chondrite was chosen as a standard following the practice of previous researchers, crosschecked against Peace River (L6), Abee (EH4), and Juvinas (EUC). Low temperature fractions (less than 900 C) give C-14 signatures consistent with a modern terrestrial C-14 source; melt fractions show elevated levels attesting to a spallogenic origin. Higher yields of CO in the melt fraction are less affected by the low levels of experimental contamination than the CO2. This fraction gave a mean CO:CO2 ratio in Bruderheim of 81.6 +/- 7.7; the ratio of the spallation component is 79.8 +/- 8.1. These values suggest equilibrium release of gases on the olivine-silica-pyroxene-iron buffer. This is corroborated by approximately equal release of the two components at 900 C. The chondrites gave an average saturation level of 54.3 +/- 2.9 dpm/kg; the achondrite gave 49.6 +/- 2.0 dpm/kg. No clear correlation with oxygen content is apparent, though shielding effects have yet to be evaluated. A further evaluation of this subject matter is given.

Cresswell, R. G.↗

NASA NTRS1993

Verification of a two-dimensional infiltration model for the resin transfer molding process

A two-dimensional finite element model for the infiltration of a dry textile preform by an injected resin was verified. The model, which is based on the finite element/control volume technique, determines the total infiltration time and the pressure increase at the mold inlet associated with the RTM process. Important input data for the model are the compaction and permeability behavior of the preform along with the kinetic and rheological behavior of the resin. The compaction behavior for several textile preforms was determined by experimental methods. A power law regression model was used to relate fiber volume fraction to the applied compaction pressure. Results showed a large increase in fiber volume fraction with the initial application of pressure. However, as the maximum fiber volume fraction was approached, the amount of compaction pressure required to decrease the porosity of the preform rapidly increased. Similarly, a power law regression model was used to relate permeability to the fiber volume fraction of the preform. Two methods were used to measure the permeability of the textile preform. The first, known as the steady state method, measures the permeability of a saturated preform under constant flow rate conditions. The second, denoted the advancing front method, determines the permeability of a dry preform to an infiltrating fluid. Water, corn oil, and an epoxy resin, Epon 815, were used to determine the effect of fluid type and viscosity on the steady state permeability behavior of the preform. Permeability values measured with the different fluids showed that fluid viscosity had no influence on the permeability behavior of 162 E-glass and TTI IM7/8HS preforms. Permeabilities measured from steady state and advancing front experiments for the warp direction of 162 E-glass fabric were similar. This behavior was noticed for tests conducted with corn oil and Epon 815. Comparable behavior was observed for the warp direction of the TTI IM7/8HS preform and corn oil. Mold filling and flow visualization experiments were performed to verify the analytical computer model. Frequency dependent electromagnetic sensors were used to monitor the resin flow front as a function of time. For the flow visualization tests, a video camera and high resolution tape recorder were used to record the experimental flow fronts. Comparisons between experimental and model predicted flow fronts agreed well for all tests. For the mold filling tests conducted at constant flow rate injection, the model was able to accurately predict the pressure increase at the mold inlet during the infiltration process. A kinetics model developed to predict the degree of cure as a function of time for the injected resin accurately calculated the increase in the degree of cure during the subsequent cure cycle.

Hammond, Vincent H.↗

NASA NTRS1993

Refractory precursor components in an Allende ferromagnesian chondrule

Chemical and petrological studies of chondrules revealed that they were formed through melting of pre-existing solid precursor materials, and that one of the refractory lithophile precursors was a high temperature condensate from the nebular gas and related to Ca, Al-rich inclusions (CAIs). Sheng et al. found relict spinel grains with isotopically fractionated Mg in plagioclase-olivine inclusions from CV chondrites and suggested that the major fractionation processes were common to CAIs and chondrules. We have determined the Mg isotopic compositon of five barred olivine chondrules and one coarse-grained rim from the Allende (CV3) meteorite. A reproducibility of instrumental isotope fractionation is plus or minus 2 per thousand per amu. The precision of the Mg-26/Mg-24 data after normalization for mass fractionation can be as good as 0.5 per thousand (2 sigma(mean)). The Mg analytical results are given and indicate that delta Mg-25/Mg-24 and sigma Mg-26 of the chondrules are normal within errors.

Misawa, Keiji↗

NASA NTRS1993

Recondensation in the early solar system: Physical conditions and source material

Many physical processes in the solar nebula led to fractionation of the gaseous phase of the preplanetary material. Some of these processes are listed with corresponding type of fractionation in terms of Rock/Ice/Gas. Recondensation from fractionated gas phase yields different compositions of condensates. In some detail, one type of fractionation is considered: impact heating with evaporation and subsequent recondensation of material during intercollisions of planetesimals. For thermodynamical simulation of recondensation in such a process one needs (1) P-T parameters and (2) some initial source material to be heated, evaporated, and recondensed. These two problems are addressed.

Vityazev, A. V.↗

NASA NTRS1992

Properties of Graphite Fiber Reinforced Copper Matrix Composites for Space Power Applications

The thermal and mechanical properties of pitch-based graphite fiber reinforced copper matrix (Gr/Cu) composites usable for space applications such as radiator fins were investigated. Thermal conductivity was measured as a function of fiber volume fraction and architecture. Results showed for unidirectional P-100 Gr/Cu composites, the longitudinal thermal conductivity was nearly independent of fiber volume fraction. Transverse thermal conductivities (perpendicular to the fibers) were strongly affected by the fiber volume fraction with higher volume fractions resulting in lower thermal conductivities. The effect of architecture on thermal conductivity followed the cosine squared law for simple architectures. Insufficient data are available currently to model more complex architectures, but adding fibers in the direction of the heat flow increases the thermal conductivity as low conductivity plies are supplemented by high conductivity plies. Thermal expansion tests were conducted on the Gr fibers and Gr/Cu composites. The results show a considerable thermal expansion mismatch between the fibers and the Cu matrix. The longitudinal thermal expansion showed a strong dependence on the architecture of the Gr/Cu composites. The composites also show a thermal expansion hysteresis. The hysteresis was eliminated by an engineered interface. Mechanical testing concentrated on the dynamic modulus and strength of the composites. The dynamic modulus of the Gr/Cu composites was 305 GPa up to 400 C, a value equivalent to Be. The strengths of the composites were less than expected, but this is attributed to the poor bond across the interface between the Gr fibers and Cu matrix. Testing of composites with an engineered interface is expected to yield strengths nearer the values predicted by the rule of mixtures.

Ellis, David L.↗

NASA NTRS1993

Pairing statistics for infrared-luminous galaxies

A knowledge of the pairing fraction of IR-selected galaxies is important in understanding the role of interactions in star formation and nuclear activity. It is clear that interactions are extremely common among the most IR-luminous systems, but results have been inconsistent for less luminous systems; this may result from using peculiar morphology as an indicator of an interaction. Since features associated with milder interactions (e.g., tidal tails) tend to be faint, their detection necessarily depends on the depth of the survey used to identify interacting pairs. We present a sample of IR- and optically-selected galaxies for which we have computed pairing fractions using strictly geometrical, quantitative criteria. For the analysis we used a likelihood ratio technique developed by Keel and van Soest (1992). We find that the pairing fraction for IR-selected galaxies is roughly 30 percent, comparable to that found by Keel and van Soest for optically-selected starbursts. We also detect a strong correlation (r above 0.99) between the 60 micron luminosity of a galaxy sample and its pairing fraction. We conclude that although tidal interactions do not guarantee enhanced activity (AGN or starburst), they can amplify internal properties that would feed such activity.

Gallimore, J. F.↗

NASA NTRS1995

AVIRIS spectral trajectories for forested areas of the Gifford Pinchot National Forest

A simple mixing model employing reference endmembers (green vegetation, non-photosynthetic vegetation, soil and shade), and using 180 AVIRIS bands, was used to establish an interpretive framework for a forested area in the Pacific Northwest. A regrowth trend, based on changes in the endmember proportions, was defined for conifers that extends from clearcuts to mature forest, and by implication to old growth. Deciduous species within replanted forest plots caused the fractions to be displaced from the main coniferous regrowth trend and to move toward the green vegetation fraction. The results indicate that the spectral information in AVIRIS can be inverted to estimate approximate stand age and relative proportion of deciduous species in the context of the area studied. Using AVIRIS we measured a 3 to 5 percent increase in woody material in old-growth forest, as distinct from other mature forest. This result is consistent with a predicted increase in NPV in old-growth forest, based on field observations. Previous application of the mixing analysis to a TM image of the same area separated old growth based solely on the shade fraction; however the approach required successful removal of shade introduced by topography. Our new results suggest that with the high spectral resolution and high signal-to-noise of AVIRIS images it may be possible to characterize and map old-growth forests in the Northwest using both the NPV fraction and shade.

Sabol, Donald E., Jr.↗

NASA NTRS1994

Constraints placed on the chondrule-forming process by merrihueite in the Mezoe-Madaras chondrite

A few unusual chondrules in the Mezoe-Madaras L3 chondrite contain the peralkaline mineral merrihueite, (K, Na)2(Fe, Mg)5Si12O30, formed by reaction of free silica in the chondrules with K, Na, Fe-rich nebular gas. Vapor fractionation was required to create chondrules poor in Al and rich in Si, and the fractionated condensate produced had to aggregate into protochondrules very promptly (on the order of hours or less) to prevent it from mixing with dust of more generalized composition in the nebula. The traditional paradigm for chondrule formation, involving a series of unrelated events (chemical fractionation of precursor dust; clumping of the dust; melting of the dust-clumps), is inadequate for making these chondrules. A rapid process, all stages of which are related, is required. We propose that this occurred during the cooling and contraction of the volume of hot gas created by a small transient high-energy event in the nebula, of unspecified nature. Microdroplets of silicate melt created by condensation from the cooling, contracting gas had velocity vectors directed toward the center of the volume. Coalescence occurred in the crowded central zone where the microdroplets converged. The Mezoe-Madaras merriihueite-bearing chondrules may have been formed by an atypically low-energy nebular event, which achieved the needed chemical fractionations by only partially vaporizing precursor dust. More commonplace chondrule types may have been created by the same basic process, but involving higher-energy events in which precursor dust was completely vaporized and recondensed.

Wood, John A.↗

NASA NTRS1994

Basalt generation at the Apollo 12 site. Part 2: Source heterogeneity, multiple melts, and crustal contamination

The petrogenesis of Apollo 12 mare basalts has been examined with emphasis on trace-element ratios and abundances. Vitrophyric basalts were used as parental compositions for the modeling, and proportions of fractionating phases were determined using the MAGFOX prograqm of Longhi (1991). Crystal fractionation processes within crustal and sub-crustal magma chambers are evaluated as a function of pressure. Knowledge of the fractionating phases allows trace-element variations to be considered as either source related or as a product of post-magma-generation processes. For the ilmenite and olivine basalts, trace-element variations are inherited from the source, but the pigeonite basalt data have been interpreted with open-system evolution processes through crustal assimilation. Three groups of basalts have been examined: (1) Pigeonite basalts-produced by the assimilation of lunar crustal material by a parental melt (up to 3% assimilation and 10% crystal fractionation, with an 'r' value of 0.3). (2) Ilmenite basalts-produced by variable degrees of partial melting (4-8%) of a source of olivine, pigeonite, augite, and plagioclase, brought together by overturn of the Lunar Magma Ocean (LMO) cumulate pile. After generation, which did not exhaust any of the minerals in the source, these melts experienced closed-system crystal fractionation/accumulation. (3) Olivine basalts-produced by variable degrees of partial melting (5-10%) of a source of olivine, pigeonite, and augite. After generation, again without exhausting any of the minerals in the source, these melts evolved through crystal accumulation. The evolved liquid counterparts of these cumulates have not been sampled. The source compositions for the ilmenite and olivine basalts were calculated by assuming that the vitrophyric compositions were primary and the magmas were produced by non-modal batch melting. Although the magnitude is unclear, evaluation of these source regions indicates that both be composed of early- and late-stage Lunar Magma Ocean (LMO) cumulates, requiring an overturn of the cumulate pile.

Neal, Clive R.↗

NASA NTRS1994

Chemical investigation of Titan and Triton tholins

We report chromatographic and spectroscopic analyses of both Titan and Triton tholins, organic solids made from the plasma irradiation of 0.9:0.1 and 0.999:0.001 N2/CH4 gas mixtures, respectively. The lower CH4 mixing ratio leads to a nitrogen-richer tholin (N/C greater than 1), probably including nitrogen heterocyclic compounds. Unlike Titan tholin, bulk Triton tholin is poor in nitriles. From high-pressure liquid chromatography, ultraviolet and infrared spectroscopy, and molecular weight estimation by gel filtration chromatography, we conclude that (1) several H2O-soluble fractions, each with distinct UV and IR spectral signatures, are present, (2) these fractions are not identical in the two tholins, (3) the H2O-soluble fractions of Titan tholins do not contain significant amounts of nitriles, despite the major role of nitriles in bulk Titan tholin, and (4) the H2O-soluble fractions of both tholins are mainly molcules containing about 10 to 50 (C + N) atoms. We report yields of amino acids upon hydrolysis of Titan and Triton tholins. Titan tholin is largely insoluble in the putative hydrocarbon lakes or oceans on Titan, but can yield the H2O-soluble species investigated here upon contact with transient (e.g., impact-generated) liquid water.

Mcdonald, Gene D.↗