SEARCH · Engineering Papers

Results for “flow visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

All sources NASA NTRS DOE OSTI

NASA NTRS1985

The Goertler instability on an airfoil

Goertler vortices arise in boundary layers along concave surfaces due to centrifugal effects. This paper presents some results of an experiment conducted to study the development of these vortices on an airfoil with a pressure gradient in the concave region where an attached laminar boundary layer was insured with suction through a perforated panel. The sublimating chemical technique was used to visualize Goertler vortices and the velocity field was measured by laser velocimetry. The vortex wavelength clearly varied with Goertler number as predicted by linear theory. Both flow visualization and velocity measurements indicated vortex damping in the convex zone. Secondary instability was observed at the higher Goertler numbers.

Mangalam, S. M.↗

NASA NTRS1988

NLF technology is ready to go

Natural laminar flow (NLF) can reduce drag on aircraft developed using modern structural design methods. Modern metal and composite construction methods can meet NLF requirements for subsonic commuter and business airframes. NLF research at NASA concentrates on expanding the practical application of NLF drag reduction technology; payoffs include progress with liquid-crystal flow visualization, NLF on three-dimensional bodies, and the effects of acoustics on laminar stability. Fuel savings from 2 to 4 percent are expected if laminar flow could be achieved over the forward 50 percent of engine nacelles on large transports depending on the configuration. It is concluded that the skill required to use NLF for drag reduction depends on understanding the conservative design corridors within which laminar flow is durable and reliable.

Holmes, Bruce J.↗

NASA NTRS1993

Control of a supersonic reattaching shear layer

A reattaching supersonic shear layer was perturbed by transverse air injection, and the effects were investigated using flow visualization. It was found that shear layer mixing was increased and that the shock system was strongly disturbed due to the heightened three dimensionality of the flow. Mixing enhancement was also achieved in an incompressible downstream-facing step flow using the same blowing procedure.

Poggie, J.↗

NASA NTRS1985

The Goertler Instability on an Airfoil

Mangalam, S. M.↗

NASA NTRS1999

Unified Model Deformation and Flow Transition Measurements

The number of optical techniques that may potentially be used during a given wind tunnel test is continually growing. These include parameter sensitive paints that are sensitive to temperature or pressure, several different types of off-body and on-body flow visualization techniques, optical angle-of-attack (AoA), optical measurement of model deformation, optical techniques for determining density or velocity, and spectroscopic techniques for determining various flow field parameters. Often in the past the various optical techniques were developed independently of each other, with little or no consideration for other techniques that might also be used during a given test. Recently two optical techniques have been increasingly requested for production measurements in NASA wind tunnels. These are the video photogrammetric (or videogrammetric) technique for measuring model deformation known as the video model deformation (VMD) technique, and the parameter sensitive paints for making global pressure and temperature measurements. Considerations for, and initial attempts at, simultaneous measurements with the pressure sensitive paint (PSP) and the videogrammetric techniques have been implemented. Temperature sensitive paint (TSP) has been found to be useful for boundary-layer transition detection since turbulent boundary layers convect heat at higher rates than laminar boundary layers of comparable thickness. Transition is marked by a characteristic surface temperature change wherever there is a difference between model and flow temperatures. Recently, additional capabilities have been implemented in the target-tracking videogrammetric measurement system. These capabilities have permitted practical simultaneous measurements using parameter sensitive paint and video model deformation measurements that led to the first successful unified test with TSP for transition detection in a large production wind tunnel.

Burner, Alpheus W.↗

NASA NTRS1990

Amplitude effects on dynamic stall of an oscillating airfoil

Amplitude effects on dynamic stall of an oscillating airfoil in locally transonic flow were studied using stroboscopic schlieren flow visualization. The dynamic stall vortex was photographed for various conditions and its properties were documented. Results show a pronounced effect of the amplitude of oscillation. The airfoil flow can sustain the larger amplitudes with the vortex retained on the surface and thus, produce dynamic lift to higher angles of attack at higher amplitudes. A possible explanation for this is offered in terms of the vorticity generation due to surface acceleration and local streamwise pressure gradient. Also, for the first time a shock has been photographed on the airfoil upper surface and some of its characteristics are discussed.

Chandrasekhara, M. S.↗

NASA NTRS1991

Aerodynamic control using forebody blowing and suction

Aerodynamic control using pneumatic forebody flow control was studied. Three methods of control were investigated: (1) blowing from a localized jet, (2) blowing from a slot, and (3) surface suction. Flow visualization and yawing moment measurements were performed on F/A-18 models in a water tunnel. The results show that all the methods were effective in controlling the forebody flow over a wide range of angles of attack and sideslip. The advantages and limitations of each of the control methods were discussed. The experiments suggested that all the control methods work basically on the principle of separation control. Based on the results of the water tunnel tests, the blowing or suction mass flow requirements appear to be within the limits of typical engine-bleed available from a modern fighter engine.

Ng, T. Terry↗

NASA NTRS1991

Aerodynamic performance of a drag reduction device on a full-scale tractor/trailer

The effectiveness of an aerodynamic boattail on a tractor/trailer road vehicle was measured in the NASA Ames Research Center 80- by 120-Foot Wind Tunnel. Results are examined for the tractor/trailer with and without the drag reduction device. Pressure measurements and flow visualization show that the aerodynamic boattail traps a vortex or eddy in the corner formed between the device and the rear corner of the trailer. This recirculating flow turns the flow inward as it separates from the edges of the base of the trailer. This modified flow behavior increases the pressure acting over the base area of the truck, thereby reducing the net aerodynamic drag of the vehicle. Drag measurements and pressure distributions in the region of the boattail device are presented for selected configurations. The optimum configuration reduces the overall drag of the tractor/trailer combination by about 10 percent at a zero yaw angle. Unsteady pressure measurements do not indicate strong vortex shedding, although the addition of the boattail plates increases high frequency content of the fluctuating pressure.

Lanser, Wendy R.↗

NASA NTRS1995

Experimental Study of Saddle Point of Attachment in Laminar Juncture Flow

An experimental study of laminar horseshoe vortex flows upstream of a cylinder/flat plate juncture has been conducted to verify the existence of saddle-point-of-attachment topologies. In the classical depiction of this flowfield, a saddle point of separation exists on the flat plate upstream of the cylinder, and the boundary layer separates from the surface. Recent computations have indicated that the topology may actually involve a saddle point of attachment on the surface and additional singular points in the flow. Laser light sheet flow visualizations have been performed on the symmetry plane and crossflow planes to identify the saddle-point-of-attachment flowfields. The visualizations reveal that saddle-point-of-attachment topologies occur over a range of Reynolds numbers in both single and multiple vortex regimes. An analysis of the flow topologies is presented that describes the existence and evolution of the singular points in the flowfield.

Coon, Michael D.↗

NASA NTRS1997

[Low-Frequency Flow Oscillation

The results of the research conducted under this grant are presented in detail in three Master theses, by Heinrich, Balow, and Broeren. Additional analysis of the experimental data can be found in two AIAA Journal articles and two conference papers. Citations for all of the studies' publications can be found in the bibliography which is attached. The objective of Heinrich's study was to document the low-frequency flow oscillation on the LRN-1007 airfoil, which had been previously observed at low Reynolds number, to determine its origin, and explore the phenomenon at higher Reynolds number. Heinrich performed detailed flow visualization on the airfoil using surface fluorescent oil and laser-sheet off-body visualization. A large leading-edge separation bubble and trailing-edge separation was identified on the airfoil just prior to the onset of the unsteady stall flow oscillation. From the laser-sheet data, the unsteady flow appeared as a massive boundary-layer separation followed by flow reattachment. Hot-wire data were taken in the wake to identify the presence of the flow oscillation and the dominant frequency. The oscillation was found in the flow from a Reynolds number of 0.3 to 1.3 x 10 exp 6. The Strouhal number based on airfoil projected height was nominally 0.02 and increased slightly with increasing Reynolds number and significantly with increasing airfoil angle of attack. Balow focused his research on the leading-edge separation bubble which was hypothesized to be the origin of the low-frequency oscillation. Initially, experimental measurements in the bubble at the onset of the low-frequency oscillation were attempted to study the characteristics of the bubble and explain possible relationships to the shear-layer-flapping phenomena. Unfortunately, the bubble proved to be extremely sensitive to the probe interference and it drastically reduced the size of the bubble. These detailed measurements were then abandoned by Balow. However, this led to a series of tests where the leading-edge bubble and trailing-edge separation were altered and the affect on the flow-oscillation studied. Balow found that by tripping the airfoil boundary-layer with "zigzag" tape ahead of bubble separation, the bubble was effectively eliminated mid the oscillation suppressed. Wake survey drag measurements showed a drastic reduction in airfoil drag when the bubble and oscillation were eliminated. Using the "zigzag" tape, the trailing-edge separation was moved downstream approximately 5 percent chord. This was found to reduce the amplitude of the oscillation, particularly in the onset stage at low angle of attack (around 14 degrees). Through detailed analysis of the wake behind the airfoil during the unsteady flow oscillation, Balow provided a better understanding of the wake flowfield. Broeren studied the oscillating flowfield in detail at Reynolds number equal 3 x 10 exp 5 and an angle of attack of 15 degrees using laser Doppler velocimetry (LDV). Two-dimensional LDV data were acquired at 687 grid points above the model upper surface while hot-wire data were taken simultaneously in the wake. Using the hot-wire signal, the LDV data were phase averaged into 24 bins to represent a single ensemble average of one oscillation cycle. The velocity data showed a flowfield oscillation that could be divided into three flow regimes. In the first regime, the flow over the airfoil was completely separated initially, the flowfield reattached from the leading edge and the reattachment point moved downstream with increasing time or phase. Broeren referred to this as the reattachment regime. The bubble development regime followed, where a leading-edge separation bubble formed at the leading edge and grew with increasing time. During the initial part of this regime the trailing-edge separation continued to move downstream. However, during the last 30 degrees of phase the trailing-edge separation moved rapidly forward and appeared to merge with the leading-edge bubble. During the third regime, the separation regime, the flow was segmented from the airfoil leading edge and did not reattach to the airfoil surface. The reverse flow was seen to grow in vertical extent up from the model surface as the phase increased. Next reattachment began again at the leading edge signaling the start of the reattachment regime, and so the cycle continued. From Broeren's work, the details of the unsteady flowfield over the airfoil were seen for the first time. From this research a great deal has been learned about the low-frequency flow oscillation which naturally occurs on the LRN-1007 airfoil near stall. The oscillation was seen to persist at higher Reynolds number, the dependence of the Strouhal number on angle of attack and Reynolds number were discovered, the critical role played by the laminar bubble was shown and the entire upper surface flowfield during a flow oscillation cycle was measured and analyzed. What still eludes understanding is the scaling of the flow oscillation and why certain airfoils, such as the LRN, have a very strong low-frequency mode and other airfoils exhibit no organized low-frequency oscillation at all.

Bragg, Michael B.↗

NASA NTRS1999

Use of Boundary Layer Transition Detection to Validate Full-Scale Flight Performance Predictions

Full-scale flight performance predictions can be made using CFD or a combination of CFD and analytical skin-friction predictions. However, no matter what method is used to obtain full-scale flight performance predictions knowledge of the boundary layer state is critical. The implementation of CFD codes solving the Navier-Stokes equations to obtain these predictions is still a time consuming, expensive process. In addition, to ultimately obtain accurate performance predictions the transition location must be fixed in the CFD model. An example, using the M2.4-7A geometry, of the change in Navier-Stokes solution with changes in transition and in turbulence model will be shown. Oil flow visualization using the M2.4-7A 4.0% scale model in the 14'x22' wind tunnel shows that fixing transition at 10% x/c in the CFD model best captures the flow physics of the wing flow field. A less costly method of obtaining full-scale performance predictions is the use of non-linear Euler codes or linear CFD codes, such as panel methods, combined with analytical skin-friction predictions. Again, knowledge of the boundary layer state is critical to the accurate determination of full-scale flight performance. Boundary layer transition detection has been performed at 0.3 and 0.9 Mach numbers over an extensive Reynolds number range using the 2.2% scale Reference H model in the NTF. A temperature sensitive paint system was used to determine the boundary layer state for these conditions. Data was obtained for three configurations: the baseline, undeflected flaps configuration; the transonic cruise configuration; and, the high-lift configuration. It was determined that at low Reynolds number conditions, in the 8 to 10 million Reynolds number range, the baseline configuration has extensive regions of laminar flow, in fact significantly more than analytical skin-friction methods predict. This configuration is fully turbulent at about 30 million Reynolds number for both 0.3 and 0.9, Mach numbers. Both the transonic cruise and the high-lift configurations were fully turbulent aft of the leading-edge flap hingeline at all Reynolds numbers.

Hamner, Marvine↗

NASA NTRS1974

Wind tunnel investigation of a simulated gunship helicopter engine-exhaust-windstream interaction

A wind tunnel investigation of the engine exhaust and windstream flow interaction on a gunship helicopter model was conducted in the Langley V/STOL tunnel. The investigation utilized a flow visualization technique employing neutrally buoyant helium filled bubbles to determine the cause of exhaust shield overheating during cruising flight and to evaluate means of eliminating the problem. The flow patterns were recorded with still cameras and on television magnetic tape. Exhaust flow impingement on the exhaust shield during cruise was found to cause the problem. Several flow altering devices were evaluated to find suitable ways to correct the problem. A flow deflector located on the model cowling upstream of the exhaust provides an effective solution.

Wilson, J. C.↗

NASA NTRS1985

Vortex research facility improvements and preliminary density stratification effects on vortex wakes

Recent modernization of NASA's Vortex Research Facility is described. The facility has a 300-ft test section, scheduled for a 300-ft extension, with constant test speeds of the model up to 100 ft/sec. The data acquisition hardware and software improvements included the installation of a 24-channel PCM system onboard the research vehicle, and a large dedicated 16-bit minicomputer. Flow visualization of the vortex wake in the test section is by particle seeding, and a thin sheet of argon laser light perpendicular to the line of flight; detailed flow field measurements are made with a laser velocimeter optics system. The improved experimental capabilities of the facility were used in a study of atmospheric stratification effects on wake vortex decay, showing that the effects of temperature gradient must be taken into account to avoid misleading conclusions in wake vortex research.

Satran, D. R.↗

NASA NTRS2010

Visual Bias Predicts Gait Adaptability in Novel Sensory Discordant Conditions

We designed a gait training study that presented combinations of visual flow and support-surface manipulations to investigate the response of healthy adults to novel discordant sensorimotor conditions. We aimed to determine whether a relationship existed between subjects visual dependence and their postural stability and cognitive performance in a new discordant environment presented at the conclusion of training (Transfer Test). Our training system comprised a treadmill placed on a motion base facing a virtual visual scene that provided a variety of sensory challenges. Ten healthy adults completed 3 training sessions during which they walked on a treadmill at 1.1 m/s while receiving discordant support-surface and visual manipulations. At the first visit, in an analysis of normalized torso translation measured in a scene-movement-only condition, 3 of 10 subjects were classified as visually dependent. During the Transfer Test, all participants received a 2-minute novel exposure. In a combined measure of stride frequency and reaction time, the non-visually dependent subjects showed improved adaptation on the Transfer Test compared to their visually dependent counterparts. This finding suggests that individual differences in the ability to adapt to new sensorimotor conditions may be explained by individuals innate sensory biases. An accurate preflight assessment of crewmembers biases for visual dependence could be used to predict their propensities to adapt to novel sensory conditions. It may also facilitate the development of customized training regimens that could expedite adaptation to alternate gravitational environments.

Brady, Rachel A.↗

NASA NTRS2024

Application of PLIF to Investigate the Hypersonic Wake of a LOFTID-Relevant Model at Mach 10

An experimental investigation of hypersonic wake flows using the planar laser-induced fluorescence (PLIF) measurement technique is summarized in this report. Off-body measurements, primarily flow visualization and velocity, were obtained for the wake of a blunt body model relevant for terrestrial re-entry and Martian entry applications within a Mach 10 hypersonic flow. The design of the model was based on the forebody aeroshell used for the LOFTID (Low-Earth Orbit Flight Test of an Inflatable Decelerator) flight vehicle. This document serves to document the experimental conditions and provide an initial analysis of select test conditions.

PLIF↗

NASA NTRS1991

A planar Mie scattering technique for visualizing supersonic mixing flows

A planar Mie scattering technique is described which allows for the direct visualization of fluid mixing in supersonic flows. The mixed fluid is visualized by laser light sheet scattering from small alcohol droplets which condense as a result of the mixing of a vapor laden subsonic stream with a cold supersonic stream. Issues related to the formation, growth and size of the droplets are addressed. The technique reveals details of the turbulent structure which are masked by the spatial integration of schlieren and shadowgraph methods. Comparative visualizations using the vapor screen method to uniformly mark the high-speed fluid are also shown.

Clemens, N. T.↗

NASA NTRS1951

Flow Over Inclined Bodies

It has been shown that the circumferential pressure distributions for the inclined body and circular cylinder deviate from their respective theoretical inviscid distributions on the lee or downstream side in the same manner. With the aid of visual flow techniques, it has been shown that there is a shedding of vortices within the crossflow field of the inclined body. It has also been found that the vortex configuration depoends to a large extent on the shape of the nose of the body. To illustrate this, vapor screen pictures were made and results are discussed.

Perkins, E. W.↗

NASA NTRS1981

On the prediction of swirling flowfields found in axisymmetric combustor geometries

The paper reports research restricted to steady turbulence flow in axisymmetric geometries under low speed and nonreacting conditions. Numerical computations are performed for a basic two-dimensional axisymmetrical flow field similar to that found in a conventional gas turbine combustor. Calculations include a stairstep boundary representation of the expansion flow, a conventional k-epsilon turbulence model and realistic accomodation of swirl effects. A preliminary evaluation of the accuracy of computed flowfields is accomplished by comparisons with flow visualizations using neutrally-buoyant helium-filled soap bubbles as tracer particles. Comparisons of calculated results show good agreement, and it is found that a problem in swirling flows is the accuracy with which the sizes and shapes of the recirculation zones may be predicted, which may be attributed to the quality of the turbulence model.

Rhode, D. L.↗