Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS1946

Field of Flow About a Jet and Effect of Jets on Stability of Jet-Propelled Airplanes

A theoretical investigation was conducted on jet-induced flow deviation. Analysis is given of flow inclination induced outside cold and hot jets and jet deflection caused by angle of attack. Applications to computation of effects of jet on longitudinal stability and trim are explained. Effect of jet temperature on flow inclination was found small when thrust coefficient is used as criterion for similitude. The average jet-induced downwash over tail plane was obtained geometrically.

Ribner, Herbert S.↗
NASA NTRS2016

Computational Analysis of Multi-Rotor Flows

Interactional aerodynamics of multi-rotor flows has been studied for a quadcopter representing a generic quad tilt-rotor aircraft in hover. The objective of the present study is to investigate the effects of the separation distances between rotors, and also fuselage and wings on the performance and efficiency of multirotor systems. Three-dimensional unsteady Navier-Stokes equations are solved using a spatially 5th order accurate scheme, dual-time stepping, and the Detached Eddy Simulation turbulence model. The results show that the separation distances as well as the wings have significant effects on the vertical forces of quadroror systems in hover. Understanding interactions in multi-rotor flows would help improve the design of next generation multi-rotor drones.

Multi-Rotor Flows↗
NASA NTRS1989

Analysis of turbulence in shear flows using the stabilization principle

An analysis is made based upon the concept that the velocity fluctuations, and therefore, the Reynolds stresses, driven by the instability of the original flow grow until a new stable state is approached. The Reynolds stresses incorporated into the Orr-Sommerfeld equation are coupled with the main flow such that all the imaginary parts of the complex eigenvalues vanish, i.e., the original instability is eliminated. Using this stabilization principle, it is possible to find the Reynolds stresses as well as the mean velocity for plane Poiseuille flow with the Reynolds number slightly higher than the critical.

Zak, M.↗
NASA NTRS1975

SINDA/SINFLO computer routine, volume 1, revision A

The SINFLO package was developed to modify the SINDA preprocessor to accept and store the input data for fluid flow systems analysis and adding the FLOSOL user subroutine to perform the flow solution. This reduced and simplified the user input required for analysis of flow problems. A temperature calculation method, the flow-hybrid method which was developed in previous VSD thermal simulator routines, was incorporated for calculating fluid temperatures. The calculation method accuracy was improved by using fluid enthalpy rather than specific heat for the convective term of the fluid temperature equation. Subroutines and data input requirements are described along with user subroutines, flow data storage, and usage of the plot program.

Oren, J. A.↗
NASA NTRS1990

Flow visualization and motion analysis for a series of four sequential brush seals

Applying the Full Flow Field Tracking (FFFT) method, the flow patterns and the accompanying fluid velocities inside a series of brushes were nonintrusively determined and graphically reconstructed. The visualized flow field revealed regions that are characteristically river-jetting, vortical, and crossflow, and exist upstream, downstream, or within the seal. These flows are especially engendered by variations in fiber void that are spatial and temporal and affect changes in seal leakage and stability. The deformation of the upper half of each of the four sequential brushes as a function of upstream pressure and mass flow was determined. The axial pressure variation across the set of four brushes and the mass flow as a function of the pressure drops are also presented.

Braun, M. J.↗
NASA NTRS2016

CFD Analysis of Mixing Characteristics of Several Fuel Injectors at Hypervelocity Flow Conditions

CFD analysis is presented of the mixing characteristics and performance of three fuel injectors at hypervelocity flow conditions. The calculations were carried out using the VULCAN-CFD solver and Reynolds-Averaged Simulations (RAS). The high Mach number flow conditions match those proposed for the planned experiments conducted as a part of the Enhanced Injection and Mixing Project (EIMP) at the NASA Langley Research Center. The EIMP aims to investigate scramjet fuel injection and mixing physics, improve the understanding of underlying physical processes, and develop enhancement strategies and functional relationships relevant to flight Mach numbers greater than eight. Because of the high Mach number flow considered, the injectors consist of a fuel placement device, a strut; and a fluidic vortical mixer, a ramp. These devices accomplish the necessary task of distributing and mixing fuel into the supersonic cross-flow albeit via different strategies. Both of these devices were previously studied at lower flight Mach numbers where they exhibited promising performance in terms of mixing efficiency and total pressure recovery. For comparison, a flush-wall injector is also included. This type of injector generally represents the simplest method of introducing fuel into a scramjet combustor, however, at high flight Mach number conditions, the dynamic pressure needed to induce sufficient fuel penetration may be difficult to achieve along with other requirements such as achieving desired levels of fuel-to-air mixing at the required equivalence ratio. The three injectors represent the baseline configurations planned for the experiments. The current work discusses the mixing flow field behavior and differences among the three fuel injectors, mixing performance as described by the mixing efficiency and the total pressure recovery, and performance considerations based on the thrust potential.

Drozda, Tomasz G.↗
NASA NTRS1980

Calculation of skin-friction coefficients for low Reynolds number turbulent boundary layer flows

An analysis is presented of the reliability of various generally accepted empirical expressions for the prediction of the skin-friction coefficient C/sub f/ of turbulent boundary layers at low Reynolds numbers in zero-pressure-gradient flows on a smooth flat plate. The skin-friction coefficients predicted from these expressions were compared to the skin-friction coefficients of experimental profiles that were determined from a graphical method formulated from the law of the wall. These expressions are found to predict values that are consistently different than those obtained from the graphical method over the range 600 Re/sub theta 2000. A curve-fitted empirical relationship was developed from the present data and yields a better estimated value of C/sub f/ in this range. The data, covering the range 200 Re/sub theta 7000, provide insight into the nature of transitional flows. They show that fully developed turbulent boundary layers occur at Reynolds numbers Re/sub theta/ down to 425. Below this level there appears to be a well-ordered evolutionary process from the laminar to the turbulent profiles. These profiles clearly display the development of the turbulent core region and the shrinking of the laminar sublayer with increasing values of Re/sub theta/.

Barr, P. K.↗
NASA NTRS1985

Simplex finite element analysis of viscous incompressible flow with penalty function formulation

Viscous flow calculations are important for the determination of separated flows, recirculating flows, secondary flows and so on. This paper presents a penalty function approach for the finite element analysis of steady incompressible viscous flow. A simplex element is used with linear velocity and constant pressure in contrast to other works which usually employ higher order elements. Simplex elements yield analytical expressions for the element matrices which in turn lead to efficient solutions. Earlier works have partially indicated how constraint and lock-up problems might be avoided for simplex elements. This paper extends the earlier works by indicating the approach in detail and verifying that it is successful for several applications not discussed in the literature so far. Solution times and accuracy considerations are discussed for Couette flow, plane Poiseuille flow, a driven cavity problem, and laminar and turbulent flow over a step.

Allaire, P. E.↗
NASA NTRS1987

Applicability of linearized-theory attached-flow methods to design and analysis of flap systems at low speeds for thin swept wings with sharp leading edges

Low-speed experimental force and data on a series of thin swept wings with sharp leading edges and leading and trailing-edge flaps are compared with predictions made using a linearized-theory method which includes estimates of vortex forces. These comparisons were made to assess the effectiveness of linearized-theory methods for use in the design and analysis of flap systems in subsonic flow. Results demonstrate that linearized-theory, attached-flow methods (with approximate representation of vortex forces) can form the basis of a rational system for flap design and analysis. Even attached-flow methods that do not take vortex forces into account can be used for the selection of optimized flap-system geometry, but design-point performance levels tend to be underestimated unless vortex forces are included. Illustrative examples of the use of these methods in the design of efficient low-speed flap systems are included.

Carlson, Harry W.↗
NASA NTRS1993

CFD Modeling of Turbulent Duct Flows for Coolant Channel Analysis

The design of modern liquid rocket engines requires the analysis of chamber coolant channels to maximize the heat transfer while minimizing the coolant flow. Coolant channels often do not remain at a constant cross section or at uniform curvature. New designs require higher aspect ratio coolant channels than previously used. To broaden the analysis capability and to complement standard analysis tools an investigation on the accuracy of CFD predictions for coolant channel flow has been initiated. Validation of CFD capabilities for coolant channel analysis will enhance the capabilities for optimizing design parameters without resorting to extensive experimental testing. The eventual goal is to use CFD to determine the flow fields of unique coolant channel designs and therefore determine critical heat transfer coefficients. In this presentation the accuracy of a particular CFD code is evaluated for turbulent flows. The first part of the presentation is a comparison of numerical results to existing cold flow data for square curved ducts (NASA CR-3367, 'Measurements of Laminar and Turbulent Flow in a Curved Duct with Thin Inlet Boundary Layers'). The results of this comparison show good agreement with the relatively coarse experimental data. The second part of the presentation compares two cases of higher aspect ratio channels (AR=2.5,10) to show changes in axial and secondary flow strength. These cases match experimental work presently in progress and will be used for future validation. The comparison shows increased secondary flow strength of the higher aspect ratio case due to the change in radius of curvature. The presentation includes a test case with a heated wall to demonstrate the program's capability. The presentation concludes with an outline of the procedure used to validate the CFD code for future design analysis.

Ungewitter, Ronald J.↗
NASA NTRS2013

Liquid Hydrogen Regulated Low Pressure High Flow Pneumatic Panel AFT Arrow Analysis

Project Definition: Design a high flow pneumatic regulation panel to be used with helium and hydrogen. The panel will have two circuits, one for gaseous helium (GHe) supplied from the GHe Movable Storage Units (MSUs) and one for gaseous hydrogen (GH2) supplied from an existing GH2 Fill Panel. The helium will supply three legs; to existing panels and on the higher pressure leg and Simulated Flight Tanks (SFTs) for the lower pressure legs. The hydrogen line will pressurize a 33,000 gallon vacuum jacketed vessel.

Jones, Kelley, M.↗
NASA NTRS1949

Preliminary Analysis of Axial-Flow Compressors Having Supersonic Velocity at the Entrance of the Stator

A supersonic compressor design having supersonic velocity at the entrance of the stator is analyzed on the assumption of two-dimensional flow. The rotor and stator losses assumed in the analysis are based on the results of preliminary supersonic cascade tests. The results of the analysis show that compression ratios per stage of 6 to 10 can be obtained with adiabatic efficiency between 70 and 80 percent. Consideration is also given in the analysis to the starting, stability, and range of efficient performance of this type of compressor. The desirability of employing variable-geometry stators and adjustable inlet guide vanes is indicated. Although either supersonic or subsonic axial component of velocity at the stator entrance can be used, the cascade test results suggest that higher pressure recovery can be obtained if the axial component is supersonic.

Ferri, Antonio↗
NASA NTRS1979

Analysis of the three dimensional flow in a turbine scroll

The present analysis describes the three-dimensional compressible inviscid flow in the scroll and the vaneless nozzle of a radial inflow turbine. The solution to this flow field, which is further complicated by the geometrical shape of the boundaries, is obtained using the finite element method. Symmetric and nonsymmetric scroll cross sectional geometries are investigated to determine their effect on the general flow field and on the exit flow conditions.

Hamed, A.↗
NASA NTRS1989

SSME alternate turbopump (pump section) axial load analysis

A flow balancing computer program constructed to calculate the axial loads on the Space Shuttle Main Engine (SSME) alternate turbopumps (ATs) pump sections are described. The loads are used in turn to determine load balancing piston design requirements. The application of the program to the inlet section, inducer/impeller/stage, bearings, seals, labyrinth, damper, piston, face and corner, and stationary/rotating surfaces is indicated. Design analysis results are reported which show that the balancing piston's designs are adequate and that performance and life will not be degraded by the turbopump's axial load characteristics.

Crease, G. A.↗
NASA NTRS1993

Analysis of hypersonic arcjet flow fields and surface heating of blunt bodies

A Gauss-Seidel implicit aerothermodynamic Navier-Stokes computational CFD code with thermochemical surface conditions (GIANTS) and with appropriate boundary conditions was developed for the analysis of hypersonic arcjet flows over large angle blunt bodies. Two-dimensional axisymmetric multicomponent full Navier-Stokes equations were solved, together with boundary conditions, to account for the surface slip, surface catalysis, and energy and mass conservation at the body surface. It is shown that the predictions for isothermal, noncatalytic, and no-slip surface conditions which are made using the GIANTS code with simple boundary conditions agree with those of the LAURA code, and the predicted normalized heating distributions over the forebody surface with boundary conditions for various cone angles are consistent with the trends of data from arcjet experiments.

Chen, Y.-K.↗
NASA NTRS1992

Flutter analysis of supersonic axial flow cascades using a high resolution Euler solver. Part 1: Formulation and validation

This report presents, in two parts, a dynamic aeroelastic stability (flutter) analysis of a cascade of blades in supersonic axial flow. Each blade of the cascade is modeled as a typical section having pitching and plunging degrees of freedom. Aerodynamic forces are obtained from a time accurate, unsteady, two-dimensional cascade solver based on the Euler equations. The solver uses a time marching flux-difference splitting (FDS) scheme. Flutter stability is analyzed in the frequency domain. The unsteady force coefficients required in the analysis are obtained by harmonically oscillating (HO) the blades for a given flow condition, oscillation frequency, and interblade phase angle. The calculated time history of the forces is then Fourier decomposed to give the required unsteady force coefficients. An influence coefficient (IC) method and a pulse response (PR) method are also implemented to reduce the computational time for the calculation of the unsteady force coefficients for any phase angle and oscillation frequency. Part 1, this report, presents these analysis methods and their validation by comparison with results obtained from linear theory for a selected flat plate cascade geometry. A typical calculation for a rotor airfoil is also included to show the applicability of the present solver for airfoil configurations. The predicted unsteady aerodynamic forces for a selected flat plate cascade geometry and flow conditions correlated well with those obtained from linear theory for different interblade phase angles and oscillation frequencies. All the three methods of predicting unsteady force coefficients, namely, HO, IC, and PR, showed good correlations with each other. It was established that only a single calculation with four blade passages is required to calculate the aerodynamic forces for any phase angle for a cascade consisting of any number of blades, for any value of the oscillation frequency. Flutter results, including mistuning effects, for a cascade of stator airfoils are presented in Part 2 of the report.

Reddy, T. S. R.↗