SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Tests were made in the NACA two-dimensional low turbulence pressure tunnel of a highly cambered low-drag airfoil (NACA 65,3-618) with a plain flap designed for lift control. The results indicate that such a combination offers attractive possibilities for obtaining low profile-drag coefficients over a wide range of lift coefficients without large reductions of critical speed.
The effects of direction of propeller rotation on factors affecting the longitudinal stability of the XB-28 airplane were measured on a 1/10-scale model in the 7- by 10-foot tunnel of the Ames Aeronautical Laboratory. The main effect observed was that caused by regions of high downwash behind the nacelles (power off as well as power on with flaps neutral). The optimum direction of propeller rotation, both propellers rotating up toward the fuselage, shifted this region off the horizontal tail and thus removed its destabilizing effect. Rotating both propellers downward toward the fuselage moved it inboard on the tail and accentuated the effect, while rotating both propellers right hand had an intermediate result. Comparisons are made of the tail effects as measured by force tests with those predicted from the point-by-point downwash and velocity surveys in the region of the tail. These surveys in turn are compared with the results predicted from available theory.
This presentation describes the current status of the joint NASA/Boeing collaboration on the development of a variable camber continuous trailing edge flap system for use in wing shaping control for cruise drag reduction.
The use of continuous trailing-edge flaps (CTEFs) for primary flight control of a helicopter main rotor is studied. A practical, optimized bimorph design with Macro-Fiber Composite actuators is developed for CTEF control, and a coupled structures and computational fluid dynamics methodology is used to study the fundamental behavior of an airfoil with CTEFs. These results are used within a comprehensive rotorcraft analysis model to study the control authority requirements of the CTEFs when utilized for primary flight control of a utility class helicopter. A study of the effect of blade root pitch index (RPI) on CTEF control authority is conducted, and the impact of structural and aerodynamic model complexity on the comprehensive analysis results is presented. The results show that primary flight control using CTEFs is promising; however, a more viable option may include the control of blade RPI, as well.
This paper presents a coupled vortex-lattice flight dynamic model with an aeroelastic finite-element model to predict dynamic characteristics of a flexible wing transport aircraft. The aircraft model is based on NASA Generic Transport Model (GTM) with representative mass and stiffness properties to achieve a wing tip deflection about twice that of a conventional transport aircraft (10% versus 5%). This flexible wing transport aircraft is referred to as an Elastically Shaped Aircraft Concept (ESAC) which is equipped with a Variable Camber Continuous Trailing Edge Flap (VCCTEF) system for active wing shaping control for drag reduction. A vortex-lattice aerodynamic model of the ESAC is developed and is coupled with an aeroelastic finite-element model via an automated geometry modeler. This coupled model is used to compute static and dynamic aeroelastic solutions. The deflection information from the finite-element model and the vortex-lattice model is used to compute unsteady contributions to the aerodynamic force and moment coefficients. A coupled aeroelastic-longitudinal flight dynamic model is developed by coupling the finite-element model with the rigid-body flight dynamic model of the GTM.
NASA's Aviation Safety Program (AvSP) develops and advances methodologies and technologies to improve air transportation safety. The Safety Analysis and Integration Team (SAIT) conducts a safety technology portfolio assessment (PA) to analyze the program content, to examine the benefits and risks of products with respect to program goals, and to support programmatic decision making. The PA process includes systematic identification of current and future safety risks as well as tracking several quantitative and qualitative metrics to ensure the program goals are addressing prominent safety risks accurately and effectively. One of the metrics within the PA process involves using quantitative aviation safety models to gauge the impact of the safety products. This paper demonstrates the role of aviation safety modeling by providing model outputs and evaluating a sample of portfolio elements using the Flightdeck Automation Problems (FLAP) model. The model enables not only ranking of the quantitative relative risk reduction impact of all portfolio elements, but also highlighting the areas with high potential impact via sensitivity and gap analyses in support of the program office. Although the model outputs are preliminary and products are notional, the process shown in this paper is essential to a comprehensive PA of NASA's safety products in the current program and future programs/projects.
This paper summarizes the recent development of an adaptive aeroelastic wing shaping control technology called variable camber continuous trailing edge flap (VCCTEF). As wing flexibility increases, aeroelastic interactions with aerodynamic forces and moments become an increasingly important consideration in aircraft design and aerodynamic performance. Furthermore, aeroelastic interactions with flight dynamics can result in issues with vehicle stability and control. The initial VCCTEF concept was developed in 2010 by NASA under a NASA Innovation Fund study entitled "Elastically Shaped Future Air Vehicle Concept," which showed that highly flexible wing aerodynamic surfaces can be elastically shaped in-flight by active control of wing twist and bending deflection in order to optimize the spanwise lift distribution for drag reduction. A collaboration between NASA and Boeing Research & Technology was subsequently funded by NASA from 2012 to 2014 to further develop the VCCTEF concept. This paper summarizes some of the key research areas conducted by NASA during the collaboration with Boeing Research and Technology. These research areas include VCCTEF design concepts, aerodynamic analysis of VCCTEF camber shapes, aerodynamic optimization of lift distribution for drag minimization, wind tunnel test results for cruise and high-lift configurations, flutter analysis and suppression control of flexible wing aircraft, and multi-objective flight control for adaptive aeroelastic wing shaping control.
This paper focuses on load alleviation optimization for a high aspect ratio truss braced wing (TBW) aircraft. The TBW aircraft model is based on the Subsonic Ultra Green Aircraft Research (SUGAR) concept developed by Boeing, with the wing structures of the model modified to include a novel aerodynamic control surface known as the Variable Camber Continuous Trailing Edge Flap (VCCTEF). The purpose of the study is to investigate the effectiveness of a Performance Adaptive Aeroelastic Wing (PAAW) technology, specifically the VCCTEF, for alleviating load on the TBW wing during flight maneuver. The specific flight maneuver under consideration in this study is a 2.5g pull-up maneuver. Constrained gradient-based optimization is conducted to tailor the deflections of the VC- CTEF such that bending moment along the wing is minimized at the 2.5g pull-up flight condition. Aerodynamic modeling for this study is conducted using a vortex-lattice method code called Vorlax. A non-linear finite element analysis (FEA) method is constructed for analyzing the structural deformation and resulting bending moment along the wing of the aircraft with the inclusion of effects from tension-stiffening due to axial loading in the truss. This study is the first phase of several, and involves optimization of a rigid wing aircraft for preliminary analysis. Future studies will incorporate flexible wing structures with aeroelastic interactions and deformations. The results of this first phase positively demonstrate the potential of utilizing the novel control surface on modern aircraft wing designs for shaping control in order to provide load alleviation during flight maneuver.
This paper discusses a wind tunnel experiment of active gust load alleviation of a flexible wing which took place at University of Washington (UW) in 2019. The experiment performed under a NASA SBIR contract with Scientific Systems Company, Inc (SSCI). The objective of the experiment is to demonstrate active controls of the Variable Camber Continuous Trailing Edge Flap (VCCTEF) system for gust load alleviation and real-time drag optimization. The wind tunnel model is a 8.2% sub-scale Common Research Model (CRM) wing. The wing structure is designed to provide a substantial degree of flexibility to represent that of a modern high-aspect ratio wing. Eight active control surfaces are employed in the VCCTEF. A new gust generator system was designed and installed by UW under a sub-contract with SSCI. The first test entry started in July 2019 and ended in September 2019. During this test entry, many significant issues were found with the hardware and software. The significant issues with the servos prevented the test objective from being completed. A follow-up second test entry in 2020 is being planned. The wing system is being repaired by SSCI. This paper reports on the progress of this experimental effort and the aeroservoelastic (ASE) model validation which was conducted during the test entry.
Aircraft designers are to a growing extent using vehicle flexibility to optimize performance with objectives such as gust load alleviation and drag minimization. More complex aerodynamically optimized configurations may also require dynamic loads and perhaps eventually flutter suppression. This paper considers an aerodynamically optimized truss-braced wing aircraft designed for a Mach 0.745 cruise. The variable camber continuous trailing edge flap concept with a feedback control system is used to enhance aeroelastic stability. A linearized reduced order aerodynamic model is developed from unsteady Reynolds averaged Navier-Stokes simulations. A static output feedback controller is developed from that model. Closed-loop simulations using the reduced order aerodynamic model show that the controller is effective in stabilizing the vehicle dynamics.
Model validation is the process of determining the degree of accuracy between the real world and the model. The result of model validation can either be used to improve the model through calibration or quantify the model-form uncertainty. This work focuses on providing the model-form uncertainty through an area metric for a hypersonic cone-slice-flap geometry configuration given uncertainty in both the simulation and experimental data. A procedure will be presented that can give an accurate representation of the model-form uncertainty using a small number of high-fidelity runs. The work will also assess the impact between using different high-fidelity solvers and different turbulence models.The goal of performing this comparison is to provide a quantifiable measurement for the accuracy of each solver and turbulence model for this type of design. A low-fidelity analysis will also be performed to get a model-form uncertainty for the lower fidelity analysis. The two high-fidelty CFD solvers used are VULCAN-CFD and FUN3D and the low-fidelity results will come from Cart3D. The experimental data came from the 20-inch Mach 6Tunnel located at NASA Langley Research Center.
Model validation is the process of determining the degree of accuracy between the real world and the model. The result of model validation can be used to either improve the model through calibration or quantify the model-form uncertainty. This work focuses on estimating the model-form uncertainty through an area metric for a hypersonic cone-slice-flap geometry configuration given the uncertainty in both the simulation and experimental data. A procedure that can give an accurate representation of the model-form uncertainty using a small number of high-fidelity runs is outlined. The work also assesses the impact of using different high-fidelity solvers and different turbulence models. The goal of performing this comparison is to provide a quantifiable measurement of the accuracy of each solver and turbulence model for this type of design. A low-fidelity analysis is also performed to get a model-form uncertainty for this type of analysis. The two high-fidelity CFD solvers used here are VULCAN-CFD and FUN3D, and the low-fidelity results comes from Cart3D.The experimental data comes from the 20-inch Mach 6 Tunnel located at NASA Langley Research Center. The work here shows that the models used tend to under-predict the drag and moment aerodynamic coefficients for this type of design leading to a model-form uncertainty estimate which can account for up to an 86% of the total uncertainty in the model predictions.
This paper presents an aerodynamic optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft with Variable-Camber Continuous Trailing-Edge Flap (VC-CTEF). The VCCTEF is a novel wing shaping control concept to improve aircraft aerodynamic efficiency. Drag reduction studies are conducted for three different VCCTEF configurations with 6-, 10-, and 21-spanwise sections, respectively. A simple VCCTEF actuator weight model is proposed to account the weight penalty of the actuator in the design. A vortex-lattice model of the TTBW model is developed with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections for rapid aerodynamic performance evaluations. The VSPAERO model has been validated against wind tunnel test data. The optimization results show that the 21-spanwise sections VCCTEF has largest absolute drag coefficient reduction, however, the 6-spanwise sections VCCTEF provides a relatively better solution for drag reduction when the actuator weight penalty is considered. A high-fidelity CFD solver FUN3D is used to validate the VCCTEF optimization.
We analyze data returned by the Magnetospheric Multiscale mission (MMS) constellation during a rapid (~1.5 s) traversal of a flapping and reconnecting current sheet (CS) in the near-Earth magnetotail (X ~ -20 RE). The CS was highly tilted, with its normal pointing strongly duskward. Its extreme thinness was confirmed by a curvature analysis of the magnetic field lines. The event was associated with a guide field of 8% of the reconnecting components. From the pitch angle distributions of low-energy electrons we infer that the crossing occurred earthward of the X-line. Traveling practically normal to the CS, MMS encountered an ion diffusion region (IDR) in which was embedded an electron diffusion region (EDR). IDR signatures included breaking of the ion frozen-in condition in the presence of Hall B and E fields. EDR signatures included a strong out of-plane current associated with a super-Alfvenic electron jet, evidence of positive energy transfer, and a temperature anisotropy (TeII > Te1) which disappeared at the field reversal. Derived scale sizes normal to the CS are: ~6.9 de (EDR) and ~0.4 di (IDR) (40 and 100 km). We estimate the average dimensionless reconnection rate as 0.077 + 0.050. The observations and inferences are supported by PIC numerical simulations. We find very good agreement in the reconnection rates. We also discuss the effects of asymmetries in the density, temperature and magnetic field strength on the Hall fields and length of the outflow jets. The event is associated with a substorm onset which began 7 min after the MMS observations.
This paper describes a fuel-optimal trajectory optimization of the Mach 0.745 Transonic Truss-Braced Wing with the variable camber continuous trailing edge flaps (VCCTEF) capable of changing the chordwise pressure distribution and spanwise lift distribution to minimize drag. The trajectory optimization is posed as a minimization of the fuel burn over a fixed cruise range. The trajectory optimization is formulated by the adjoint method which results in a two-point boundary value problem. A numerical shooting method is implemented to solve the minimum-fuel trajectory optimization. The results indicates a fuel burn reduction of 793 lbs or 5.5% for a cruise range of 3000 miles. An approximate trajectory optimization is proposed using a single adjoint variable. This leads to a greatly simplified analytical solution of the adjoint solution. The results of the approximate trajectory optimization are in excellent agreement with those obtained by the shooting method. The approximate trajectory optimization produces a fuel burn reduction of 615 lbs or 4.3%.
This paper presents an aeroelastic trim drag optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft with the Variable-Camber Continuous Trailing-Edge Flap (VCCTEF). An aero-structural analysis solver VSPAERO with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections coupled to finite-element code BEAM3D is developed to provide a rapid aircraft aeroelastic performance evaluation. The VSPAERO model has been validated against wind tunnel test data. Aeroelastic trim drag optimization studies are conducted for a VCCTEF configuration with 6-spanwise sections. Three different flight conditions corresponding to Mach 0.745 are selected for the TTBW aircraft aeroelastic trim drag optimization at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized VCCTEF deflection achieves a drag reduction of about 9.1 counts, 5.9 counts, and 11.8 counts corresponding to the lift coefficients 0.68, 0.73, and 0.78, respectively. A high-fidelity CFD solver FUN3D is used to validate the aeroelastic trim drag optimization.
The goal of this project was to develop a model for a single subsystem in the aerodynamics discipline, in this case the flaps of an aircraft. This presentation details the building of the model. Additionally, this presentation discusses my goals and accomplishments as a summer intern, as a job experience and my hopes for my future at NASA as well
This paper presents an aerodynamic optimization study of the Mach 0.8 Transonic Truss-Braced Wing (TTBW) aircraft with Variable Camber Continuous Trailing Edge Flap (VC-CTEF). The VCCTEF is a novel wing shaping control concept to improve aircraft aerodynamic efficiency. Drag reduction studies are conducted for two different VCCTEF configurations with 6- and 10-spanwise sections, respectively. A simple VCCTEF actuator weight model is used to account the weight penalty of the actuator in the design for the Mach 0.8 TTBW aircraft. A vortex-lattice model of the Mach 0.8 TTBW aircraft is developed with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections for rapid aerodynamic performance evaluations. The VSPAERO model has been validated against the wind tunnel test data. The optimization results show that the 6-spanwise sections VCCTEF provides a relatively better solution for drag reduction when the actuator weight penalty is considered. A high-fidelity CFD solver FUN3D is used to verify the VCCTEF optimization design.