SEARCH · Engineering Papers

Results for “finite element methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Gear Lubrication and Cooling Experiment and Analysis

A gear tooth temperature analysis was performed using a finite element method combined with a calculated heat input, a calculated oil jet impingement depth, and estimated heat transfer coefficients for the different parts of the gear tooth that are oil cooled and air cooled. Experimental measurements of gear tooth average surface temperature and gear tooth instantaneous surface temperature were made with a fast response, infrared, radiometric microscope. Increasing oil pressure has a significant effect on both average surface temperature and peak surface temperature at loads above 1895 N/cm(1083 lb/in) and speeds of 10,000 and 7500 rpm. Both increasing speed (from 5000 to 10,000 rpm) at constant speed cause a significant rise in the average surface temperature and in the instantaneous peak surface temperatures on the gear teeth. The oil jet pressure required to provide the best cooling for gears is the pressure required to obtain full gear tooth impingement. Calculated results for gear tooth temperatures were close to experimental results for various oil jet impingement depths for identical operating conditions.

Townsend, D. P.↗

NASA NTRS1983

A computer code for performance of spur gears

In spur gears both performance and failure predictions are known to be strongly dependent on the variation of load, lubricant film thickness, and total flash or contact temperature of the contacting point as it moves along the contact path. The need of an accurate tool for predicting these variables has prompted the development of a computer code based on recent findings in EHL and on finite element methods. The analyses and some typical results which to illustrate effects of gear geometry, velocity, load, lubricant viscosity, and surface convective heat transfer coefficient on the performance of spur gears are analyzed.

Wang, K. L.↗

NASA NTRS1983

The TEKLIB graphic library

TEKLIB is a library of procedures written in TI PASCAL to perform basic graphic tasks. TEKLIB was written to provide an interface between a graphics terminal and the TI 990. The TI 990 is used as a controller for the Finite Element Machine which is an array of microprocessors designed to solve problems by finite element methods in parallel. The use of TEKLIB provides a means of inputting data graphically and displaying output.

Bostic, S. W.↗

NASA NTRS1983

Vibration characteristics of a deployable controllable-geometry truss boom

An analytical study was made to evaluate changes in the fundamental frequency of a two dimensional cantilevered truss boom at various stages of deployment. The truss could be axially deployed or retracted and undergo a variety of controlled geometry changes by shortening or lengthening the telescoping diagonal members in each bay. Both untapered and tapered versions of the truss boom were modeled and analyzed by using the finite element method. Large reductions in fundamental frequency occurred for both the untapered and tapered trusses when they were uniformly retracted or maneuvered laterally from their fully deployed position. These frequency reductions can be minimized, however, if truss geometries are selected which maintain cantilever root stiffness during truss maneuvers.

Dorsey, J. T.↗

NASA NTRS1982

Required developments in structural dynamics

The finite element method, modal component synthesis, and the use of fast Fourier transformation were key developments in structural dynamics in the past 15 to 20 years. Current areas requiring additional effort include: (1) the correct calculation of modal shape and natural frequencies for complex structures; (2) the correlation of math models with test data; (3) the establishment of a criteria for "goodness" of the correlation between analysis and test; (4) the selection of the correct displacement functions when using computer programs for modal synthesis; (5) accuracy of response calculations; and (6) the inverse problem of determining the force problem from the response data. Trends identified include the use of distributed computing, greater reliance on analysis, and the possible use of artificial intelligence techniques, or some way of feeding back information, to provide solution guidance to engineers.

Wada, B. K.↗

NASA NTRS1983

FEM array control software user's guide

Finite Element method (FEM) Array Control Software (FACS) is a user-friendly, interactive software package designed to provide a user interface to the FEM. The use of the FACS commands are described.

Knott, J. D.↗

NASA NTRS1983

Two-dimensional Finite Element Modeling for Modeling Tectonic Stress and Strain

Techniques of finite element analysis in two dimensional plane strain were applied to problems of geophysics and tectonics. More specifically, the flexibility of the finite element method was employed to address problems involving geological complexity and fault interactions. The modeling of effective anisotropy in material elastic properties proved useful in describing the deformation of faulted crustal blocks. The applications of this modeling work to problems of actual tectonics in southern California was explored. Preliminary models show encouraging agreement with measured tectonic strain in this region, and modeling work was done to gain an understanding of the stress state in a locked fault region with future seismic potential.

Lyzenga, G. A.↗

NASA NTRS1983

A new formulation of hybrid/mixed finite element

A new formulation of finite element method is accomplished by the Hellinger-Reissner principle for which the stress equilibrium conditions are not introduced initially but are brought-in through the use of additional internal displacement parameters. The method can lead to the same result as the assumed stress hybrid model. However, it is more general and more flexible. The use of natural coordinates for stress assumptions leads to elements which are less sensitive to the choice of reference coordinates. Numerical solutions by 3-D solid element indicate that more efficient elements can be constructed by assumed stresses which only partially satisfy the equilibrium conditions.

Pian, T. H. H.↗

NASA NTRS1982

The evolution of the moon - A finite element approach

The present lunar evolution model analyzes the thermal history of a self-gravitating spherical planetary body, including the effects of viscous dissipation, internal melting, adiabatic gradient, core formation, variable viscosity, radioactive nucleide decay, and a depth-dependent initial temperature profile, together with physical parameters corresponding to the moon. Although no initial basalt ocean is assumed, partial melting is observed early in the model moon's history. This is suggested to be related to the formation of the basalt maria. The model's present lithospheric thickness is 600 km, with core-mantle temperatures close to 1600 K and surface heat flux of 25.3 mW/sq m. The finite element method is judged to be applicable to the problem of planetary evolution, although faster solution algorithms will be required for the examination of a sufficient number of models.

Chacko, S.↗

NASA NTRS1983

A refined finite element for vibration analysis of twisted blades based on beam theory

A finite element method of discretizing beam segments of pretwisted rotating blades is presented. Employing the matrix displacement method, stiffness and mass properties are developed from basic mechanics of a pretwisted beam theory. By introducing the proper displacement functions, the effect of rotor blade rotational motion on the stiffness matrix is obtained systematically from the kinetic energy expression. Comparing with other beam elements the derivation of this element is more fundamental. This allows one to apply the same approach to more complicated problems including nonlinear effects or complex dynamic motions. Illustrative examples are given comparing numerical results with available data and other numerical solutions from rotating and nonrotating force fields. These examples show that accurate prediction of vibration frequencies for pretwisted blades can be obtained by employing a quite modest number of degrees of freedom.

Sisto, F.↗

NASA NTRS1983

Design for temperature and thermal buckling constraints employing a noneigenvalue formulation

A numerical procedure for simultaneous consideration of structural/thermal interactions during aircraft design is presented, with an emphasis on reentry vehicles such as the Orbiter. It has been shown that sequential design is inappropriate for reentry vehicles, due to the degradation of the material properties at elevated reentry temperatures. Attention is focused on thermal buckling, using an analytical technique that involves requiring that the stability matrix be positive definite, with the diagonal terms on the Gauss-Doolittle factor of the matrix also constrained to be positive. A finite element method is employed to calculate the derivative of the diagonal matrix, with optimization achieved by minimization of the mass of the structure and thermal protection system. Sample calculations are presented in terms of the aluminum structure and insulation for a section of the Orbiter wing bay.

Haftka, R. T.↗

NASA NTRS1982

Finite element analysis of the effect of a non-planar solid-liquid interface on the lateral solute segregation during unidirectional solidification

The effect of solid-liquid interface shape on lateral solute segregation during steady-state unidirectional solidification of a binary mixture is calculated under the assumption of no convection in the liquid. A finite element technique is employed to compute the concentration field in the liquid and the lateral segregation in the solid with a curved boundary between the liquid and solid phases. The computational model is constructed assuming knowledge of the solid-liquid interface shape; no attempt is made to relate this shape to the thermal field. The influence of interface curvature on the lateral compositional variation is investigated over a range of system parameters including diffusivity, growth speed, distribution coefficient, and geometric factors of the system. In the limiting case of a slightly nonplanar interface, numerical results from the finite element technique are in good agreement with the analytical solutions of Coriell and Sekerka obtained by using linear theory. For the general case of highly non-planar interface shapes, the linear theory fails and the concentration field in the liquid as well as the lateral solute segregation in the solid can be calculated by using the finite element method.

Carlson, F. M.↗

NASA NTRS1982

Conceptual support design of the high resolution mirror assembly for the Advanced X-ray Astrophysics Facility (AXAF)

The performance goals of the Advanced X-ray Astrophysics Facility (AXAF) require that the Wolter I optics support system be insensitive to temperature fluctuations and the effects of gravity during ground testing. Previous work has shown that acceptable concepts are achievable but require much attention to design details. This paper discusses a new support system wherein each optic is held by a single circumfererential ring near its center of mass rather than a multipoint support as previously analyzed. The thermal sensitivity of this system is considerably lower than any concept yet studied. This advanced support concept allows the use of a wider variety of mateials and simple design details. Structural analysis utilizing the finite element method and optical ray-trace analysis are used to predict the system performance.

Cohen, L. M.↗

NASA NTRS1983

Specification for a Program for an Interative Aeroelastic Solution (PIAS)

An engineering and software specification which was written for a computer program to calculate aeroelastic structural loads including the effects of nonlinear aerodynamics is presented. The procedure used in the program for an iterative aeroelastic solution (PIAS) is to alternately execute two computer codes: one to calculate aerodynamic loads for a specific wing shape, and another to calculate the deflected shape caused by this loading. A significant advantage to the design of PIAS is that the initial aerodynamic module can be replaced with others. The leading edge vortex (LEV) program is used as the aerodynamic module in PIAS. This provides the capability to calculate aeroelastic loads, including the effects of a separation induced leading edge vortex. The finite element method available in ATLAS Integrated structural analysis and design system is used to determine the deflected wing shape for the applied aerodynamics and inertia loads. The data management capabilities in ATLAS are used by the execution control monitor (ECM) of PIAS to control the solution process.

Manro, M. E.↗

NASA NTRS1983

Theoretical and software considerations for nonlinear dynamic analysis

In the finite element method for structural analysis, it is generally necessary to discretize the structural model into a very large number of elements to accurately evaluate displacements, strains, and stresses. As the complexity of the model increases, the number of degrees of freedom can easily exceed the capacity of present-day software system. Improvements of structural analysis software including more efficient use of existing hardware and improved structural modeling techniques are discussed. One modeling technique that is used successfully in static linear and nonlinear analysis is multilevel substructuring. This research extends the use of multilevel substructure modeling to include dynamic analysis and defines the requirements for a general purpose software system capable of efficient nonlinear dynamic analysis. The multilevel substructuring technique is presented, the analytical formulations and computational procedures for dynamic analysis and nonlinear mechanics are reviewed, and an approach to the design and implementation of a general purpose structural software system is presented.

Schmidt, R. J.↗

NASA NTRS1983

Eleventh NASTRAN User's Colloquium

NASTRAN (NASA STRUCTURAL ANALYSIS) is a large, comprehensive, nonproprietary, general purpose finite element computer code for structural analysis which was developed under NASA sponsorship. The Eleventh Colloquium provides some comprehensive general papers on the application of finite element methods in engineering, comparisons with other approaches, unique applications, pre- and post-processing or auxiliary programs, and new methods of analysis with NASTRAN.

Source record↗

NASA NTRS1984

Development of a thermal and structural model for a NASTRAN finite-element analysis of a hypersonic wing test structure

The development of a thermal and structural model for a hypersonic wing test structure using the NASTRAN finite-element method as its primary analytical tool is described. A detailed analysis was defined to obtain the temperature and thermal stress distribution in the whole wing as well as the five upper and lower root panels. During the development of the models, it was found that the thermal application of NASTRAN and the VIEW program, used for the generation of the radiation exchange coefficients, were definicent. Although for most of these deficiencies solutions could be found, the existence of one particular deficiency in the current thermal model prevented the final computation of the temperature distributions. A SPAR analysis of a single bay of the wing, using data converted from the original NASTRAN model, indicates that local temperature-time distributions can be obtained with good agreement with the test data. The conversion of the NASTRAN thermal model into a SPAR model is recommended to meet the immediate goal of obtaining an accurate thermal stress distribution.

Lameris, J.↗

NASA NTRS1984

Nonlinear Structural Analysis

Nonlinear structural analysis techniques for engine structures and components are addressed. The finite element method and boundary element method are discussed in terms of stress and structural analyses of shells, plates, and laminates.

Source record↗