Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrolytes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

A New Class of Ionically Conducting Fluorinated Ether Electrolytes with High Electrochemical Stability

Increasing battery energy density is greatly desired for applications such as portable electronics and transportation. However, many next-generation batteries are limited by electrolyte selection because high ionic conductivity and poor electrochemical stability are typically observed in most electrolytes. For example, ether-based electrolytes have high ionic conductivity but are oxidatively unstable above 4 V, which prevents the use of high-voltage cathodes that promise higher energy densities. In contrast, hydrofluoroethers (HFEs) have high oxidative stability but do not dissolve lithium salt. Here, we synthesize a new class of fluorinated ether electrolytes that combine the oxidative stability of HFEs with the ionic conductivity of ethers in a single compound. We show that conductivities of up to 2.7 × 10 –4 S/cm (at 30 °C) can be obtained with oxidative stability up to 5.6 V. The compounds also show higher lithium transference numbers compared to typical ethers. Furthermore, we use nuclear magnetic resonance (NMR) and molecular dynamics (MD) to study their ionic transport behavior and ion solvation environment, respectively. Finally, we demonstrate that this new class of electrolytes can be used with a Ni-rich layered cathode (NMC 811) to obtain over 100 cycles at a C/5 rate. The design of new molecules with high ionic conductivity and high electrochemical stability is a novel approach for the rational design of next-generation batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Elucidating the Molecular Origins of the Transference Number in Battery Electrolytes Using Computer Simulations

The rate at which rechargeable batteries can be charged and discharged is governed by the selective transport of the working ions through the electrolyte. Conductivity, the parameter commonly used to characterize ion transport in electrolytes, reflects the mobility of both cations and anions. The transference number, a parameter introduced over a century ago, sheds light on the relative rates of cation and anion transport. This parameter is, not surprisingly, affected by cation–cation, anion–anion, and cation–anion correlations. In addition, it is affected by correlations between the ions and neutral solvent molecules. Computer simulations have the potential to provide insights into the nature of these correlations. We review the dominant theoretical approaches used to predict the transference number from simulations by using a model univalent lithium electrolyte. In electrolytes of low concentration, one can obtain a quantitative model by assuming that the solution is made up of discrete ion-containing clusters–neutral ion pairs, negatively and positively charged triplets, neutral quadruplets, and so on. These clusters can be identified in simulations using simple algorithms, provided their lifetimes are sufficiently long. In concentrated electrolytes, more clusters are short-lived and more rigorous approaches that account for all correlations are necessary to quantify transference. Elucidating the molecular origin of the transference number in this limit remains an unmet challenge.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Organosulfide-plasticized solid-electrolyte interphase layer enables stable lithium metal anodes for long-cycle lithium-sulfur batteries

Lithium metal is a promising anode candidate for the next-generation rechargeable battery due to its highest specific capacity (3860 mA h g -1 ) and lowest potential, but low Coulombic efficiency and formation of lithium dendrites hinder its practical application. Here, we report a self-formed flexible hybrid solid-electrolyte interphase layer through co-deposition of organosulfides/organopolysulfides and inorganic lithium salts using sulfur-containing polymers as an additive in the electrolyte. The organosulfides/organopolysulfides serve as “plasticizer” in the solid-electrolyte interphase layer to improve its mechanical flexibility and toughness. The as-formed robust solid-electrolyte interphase layers enable dendrite-free lithium deposition and significantly improve Coulombic efficiency (99% over 400 cycles at a current density of 2mAcm -2 ). A lithium-sulfur battery based on this strategy exhibits long cycling life (1000 cycles) and good capacity retention. This study reveals an avenue to effectively fabricate stable solid-electrolyte interphase layer for solving the issues associated with lithium metal anodes.

25 ENERGY STORAGE↗

Single-phase local-high-concentration solid polymer electrolytes for lithium-metal batteries

Solid polymers are promising electrolytes for Li-metal batteries, but they have limitations: they cannot simultaneously achieve high ionic conductivity, good mechanical strength and compatibility with high-voltage cathodes while suppressing Li dendrites. Here, we design a class of locally high-concentration solid polymer electrolytes based on polymer blends, which are termed Li-polymer in F diluter (LPIFD). The Li-polymer (polymer-in-salt) ensures continuous Li-ion conduction channels and contributes to the solid electrolyte interphase (SEI), and the F diluter (inert fluorinated polymer) adds mechanical strength. Studies reveal that a single-phase LPIFD, which is based on a miscible polymer blend, lacks phase boundaries and forms an organic-less and LiF-rich SEI, effectively suppressing lithium dendrites. The single-phase LPIFD delivers ionic conductivity of 3.0 x 10 -4 S cm -1 and enables the Li anode to reach a high coulombic efficiency of 99.1% and a critical current density of 3.7 mA cm -2 . Furthermore, the ability to form an F-rich cathode electrolyte interphase allows LiNi 0.8 Co 0.1 Mn 0.1 O 2 ||Li cells to achieve a cycle life of 450 cycles at a high operating voltage of 4.5 V. In conclusion, this design will inspire efforts to commercialize polymer electrolytes for high-energy Li-metal batteries.

25 ENERGY STORAGE↗

Air-Stable, High-Conduction Solid Electrolytes of Arsenic-Substituted Li4SnS4

Lithium-ion-conducting solid electrolytes show promise for enabling high-energy secondary battery chemistries and solving safety issues associated with conventional lithium batteries. Achieving the combination of high ionic conductivity and outstanding chemical stability in solid electrolytes is a grand challenge for the synthesis of solid electrolytes. Herein we report the design of aliovalent substitution of Li4SnS4 to achieve high conduction and excellent air stability based on the hard and soft acids and bases theory. The composition of Li3.833Sn0.833As 0.166S4 has a high ionic conductivity of 1.39 mS/cm 1 at 25 C. Considering the high Li+ transference number, this phase conducts Li+ as well as carbonate-based liquid electrolytes. This research also addresses the compatibility of the sulfide-based solid electrolytes through chemical passivation.

energy storage↗

A high-conduction Ge substituted Li3AsS4 solid electrolyte with exceptional low activation energy

In lithium-ion conducting solid electrolytes the potential to enable high-energy-density secondary batteries and offer distinctive safety features as an advantage over traditional liquid electrolytes is shown. Achieving the combination of high ionic conductivity, low activation energy, and outstanding electrochemical stability in crystalline solid electrolytes is a challenge for the synthesis of novel solid electrolytes. We report an exceptionally low activation energy (Ea) and high room temperature superionic conductivity via facile aliovalent substitution of Li 3 AsS 4 by Ge, which increased the conductivity by two orders of magnitude as compared to the parent compound. The composition Li 3.334 Ge 0.334 As 0.666 S 4 has a high ionic conductivity of 1.12 mScm -1 at 27°C. Local Li + hopping in this material is accompanied by distinctive low activation energy Ea of 0.17 eV being the lowest of Li + solid conductors. Finally, our study demonstrates the efficacy of surface passivation of solid electrolyte to achieve compatibility with metallic lithium electrodes.

25 ENERGY STORAGE↗

Fabrication of ultrathin solid electrolyte membranes of β-Li 3 PS 4 nanoflakes by evaporation-induced self-assembly for all-solid-state batteries

All-solid-state lithium batteries are attractive candidates for next-generation energy storage devices because of their anticipated high energy density and intrinsic safety. Owing to their excellent ionic conductivity and stability with metallic lithium anodes, nanostructured lithium thiophosphate solid electrolytes such as β-Li 3 PS 4 have found use in the fabrication of all-solid lithium batteries for large-scale energy storage systems. However, current methods for preparing air-sensitive solid electrolyte membranes of lithium thiophosphates can only generate thick membranes that compromise the battery's gravimetric/volumetric energy density and thus its rate performance. To overcome this limitation, the solid electrolyte's thickness needs to be effectively decreased to achieve ideal energy density and enhanced rate performance. In this paper, we show that the evaporation-induced self-assembly (EISA) technique produces ultrathin membranes of a lithium thiophosphate solid electrolyte with controllable thicknesses between 8 and 50 μm while maintaining the high ionic conductivity of β-Li 3 PS 4 and stability with metallic lithium anodes up to 5 V. Finally, it is clearly demonstrated that this facile EISA approach allows for the preparation of ultrathin lithium thiophosphate solid electrolyte membranes for all-solid-state batteries.

25 ENERGY STORAGE↗

Tailoring the structural durability and proton conductivity of electrolytes for highly fuel-flexible and reversible ceramic cells

A durable and high ionic conducting electrolyte is critical for achieving fuel-flexible and reversible protonic ceramic cells (PCCs) at reduced temperatures since the developed electrolyte materials are vulnerable to steam, CO 2 , or coking deterioration. Here, we report a fast-conducting electrolyte material BaZr 0.06 Ce 0.7 Y 0.06 Yb 0.06 Hf 0.06 Gd 0.06 O 3−δ (BZCYYbHG), demonstrating excellent durability against CO 2 and H 2 O under the realistic electrolysis operations, and a high conductivity of 0.017 S cm −1 at 550 °C for lowering the PCC operating temperature. Further, density functional theory calculations indicate that the higher configurational entropy of mixing at the B-site cations slightly reduces the hydrogen adsorption energy, suggesting a higher incorporation rate of protons or hydrogen atoms into the electrolyte bulk. Ultimately, single cells with the BZCYYbHG electrolyte deliver peak power densities of 1.39, 1.12, and 0.7 W cm −2 in H 2 , NH 3 , and wet CH 4 at 550 °C with promising durability. In addition, the PCCs achieve a current density of −1.61 A cm −2 at 1.3 V and 550 °C with a high faradaic efficiency of 91.3% at −0.5 A cm −2 , enabling stable operations in steam electrolysis mode under humid air (30% H 2 O), wet air containing CO 2 (up to 10%), and reversible cycling.

25 ENERGY STORAGE↗

Excited state intramolecular charge transfer reaction in nonaqueous electrolyte solutions: Temperature dependence

Temperature dependence of the excited state intramolecular charge transfer reaction of 4-(1-azetidinyl)benzonitrile (P4C) in ethyl acetate (EA), acetonitrile (ACN), and ethanol at several concentrations of lithium perchlorate (LiClO{sub 4}) has been investigated by using the steady state and time resolved fluorescence spectroscopic techniques. The temperature range considered is 267-343 K. The temperature dependent spectral peak shifts and reaction driving force (-{Delta}G{sub r}) in electrolyte solutions of these solvents can be explained qualitatively in terms of interaction between the reactant molecule and ion-atmosphere. Time resolved studies indicate that the decay kinetics of P4C is biexponential, regardless of solvents, LiClO{sub 4} concentrations, and temperatures considered. Except at higher electrolyte concentrations in EA, reaction rates in solutions follow the Arrhenius-type temperature dependence where the estimated activation energy exhibits substantial electrolyte concentration dependence. The average of the experimentally measured activation energies in these three neat solvents is found to be in very good agreement with the predicted value based on data in room temperature solvents. While the rate constant in EA shows a electrolyte concentration induced parabolic dependence on reaction driving force (-{Delta}G{sub r}), the former in ethanol and ACN increases only linearly with the increase in driving force (-{Delta}G{sub r}). The data presented here also indicate that the step-wise increase in solvent reorganization energy via sequential addition of electrolyte induces the ICT reaction in weakly polar solvents to crossover from the Marcus inverted region to the normal region.

36 MATERIALS SCIENCE↗

High performance of SDC and GDC core shell type composite electrolytes using methane as a fuel for low temperature SOFC

Nanocomposites Samarium doped Ceria (SDC), Gadolinium doped Ceria (GDC), core shell SDC amorphous Na{sub 2}CO{sub 3} (SDCC) and GDC amorphous Na{sub 2}CO{sub 3} (GDCC) were synthesized using co-precipitation method and then compared to obtain better solid oxide electrolytes materials for low temperature Solid Oxide Fuel Cell (SOFCs). The comparison is done in terms of structure, crystallanity, thermal stability, conductivity and cell performance. In present work, XRD analysis confirmed proper doping of Sm and Gd in both single phase (SDC, GDC) and dual phase core shell (SDCC, GDCC) electrolyte materials. EDX analysis validated the presence of Sm and Gd in both single and dual phase electrolyte materials; also confirming the presence of amorphous Na{sub 2}CO{sub 3} in SDCC and GDCC. From TGA analysis a steep weight loss is observed in case of SDCC and GDCC when temperature rises above 725 °C while SDC and GDC do not show any loss. The ionic conductivity and cell performance of single phase SDC and GDC nanocomposite were compared with core shell GDC/amorphous Na{sub 2}CO{sub 3} and SDC/ amorphous Na{sub 2}CO{sub 3} nanocomposites using methane fuel. It is observed that dual phase core shell electrolytes materials (SDCC, GDCC) show better performance in low temperature range than their corresponding single phase electrolyte materials (SDC, GDC) with methane fuel.

36 MATERIALS SCIENCE↗

Broadband NMR relaxometry of electrolytes for energy storage

An increasing use of the fast field cycling nuclear magnetic resonance relaxometry technique to investigate dynamics in electrolytes for energy storage has been evidenced during the last decade. Therefore, this review article describes some of the research carried out on electrolytes during the last ten years using this technique. These studies include various types of liquid electrolytes, such as ionic liquids and deep eutectic solvents, semi-solid-state electrolytes, in particular ionogels and polymer gels, and solid electrolytes such as glasses, glass ceramics and polymers. Here, an extended description of the different models used to explain the relaxation rate profiles is presented throughout this article.

25 ENERGY STORAGE↗

Compliant glass–polymer hybrid single ion-conducting electrolytes for lithium batteries

Despite high ionic conductivities, current inorganic solid electrolytes cannot be used in lithium batteries because of a lack of compliance and adhesion to active particles in battery electrodes as they are discharged and charged. Here, we have successfully developed a compliant, nonflammable, hybrid single ion-conducting electrolyte comprising inorganic sulfide glass particles covalently bonded to a perfluoropolyether polymer. The hybrid with 23 wt% perfluoropolyether exhibits low shear modulus relative to neat glass electrolytes, ionic conductivity of 10 -4 S/cm at room temperature, a cation transference number close to unity, and an electrochemical stability window up to 5 V relative to Li + /Li. X-ray absorption spectroscopy indicates that the hybrid electrolyte limits lithium polysulfide dissolution and is, thus, ideally suited for Li-S cells. Our work opens a previously unidentified route for developing compliant solid electrolytes that will address the challenges of lithium batteries.

25 ENERGY STORAGE↗

Can ionophobic nanopores enhance the energy storage capacity of electric-double-layer capacitors containing nonaqueous electrolytes?

The ionophobicity effect of nanoporous electrodes on the capacitance and the energy storage capacity of nonaqueous-electrolyte supercapacitors is studied by means of the classical density functional theory (DFT). It has been hypothesized that ionophobic nanopores may create obstacles in charging, but they store energy much more efficiently than ionophilic pores. In this paper, we find that, for both ionic liquids and organic electrolytes, an ionophobic pore exhibits a charging behavior different from that of an ionophilic pore, and that the capacitance–voltage curve changes from a bell shape to a two-hump camel shape when the pore ionophobicity increases. For electric-double-layer capacitors containing organic electrolytes, an increase in the ionophobicity of the nanopores leads to a higher capacity for energy storage. Without taking into account the effects of background screening, the DFT predicts that an ionophobic pore containing an ionic liquid does not enhance the supercapacitor performance within the practical voltage ranges. However, by using an effective dielectric constant to account for ion polarizability, the DFT predicts that, like an organic electrolyte, an ionophobic pore with an ionic liquid is also able to increase the energy stored when the electrode voltage is beyond a certain value. We find that the critical voltage for an enhanced capacitance in an ionic liquid is larger than that in an organic electrolyte. Finally, our theoretical predictions provide further understanding of how chemical modification of porous electrodes affects the performance of supercapacitors.

25 ENERGY STORAGE↗

Highly Concentrated Electrolytes: Electrochemical and Physicochemical Characteristics of LiPF 6 in Propylene Carbonate Solutions

Highly concentrated electrolytes (HCEs) based on LiPF 6 in propylene carbonate (PC) have been examined as lithium-ion battery electrolytes. These HCEs have lower ionic conductivities and higher viscosities than ethylene carbonate (EC) electrolytes with 1.2 M LiPF 6 , but they have higher Li + ion transference numbers. Electrochemical cycling behaviour of LiNi 0.8 Co 0.015 Al 0.05 O 2 //graphite cells with 3.2 M LiPF 6 in PC resembles that of cells with EC-based electrolytes; the HCE cells have higher impedance, which can be lowered by increasing test temperature. By employing Raman and infrared spectroscopy, combined with density functional theory and ab initio molecular dynamics simulations, we reveal that the Li + solvation structure and speciation are key factors that determine cell performance. Two distinct regimes are observed as a function of salt concentration—in the conventional regime, the solvation number (SN) is mostly constant, while in the HCE regime it decreases linearly. Graphite exfoliation is suppressed only at very high salt concentrations ( > 2.4 M), where [ PC ] free /[Li + ] < 1 and P F 6 − f r e e > P C f r e e . Results from the Advanced Electrolyte Model indicate that Li + desolvation improves at higher LiPF 6 concentrations, thereby mitigating PC co-intercalation into the graphite. However, Li + ion transport is hindered in the HCEs, which increases impedance at both the oxide-positive and graphite-negative electrodes.

25 ENERGY STORAGE↗

Enabling Non-Carbonate Electrolytes for Silicon Anode Batteries Using Fluoroethylene Carbonate

Silicon is considered as one of the most promising anodes for next generation lithium-ion batteries, due to its high theoretical capacity and energy density. However, many technical barriers remain to its implementation, due to its high chemical/electrochemical reactivities with standard electrolytes and incomplete passivation. In this work, we take the most effective passivating additive of fluoroethylene carbonate (FEC) and study its impact on non-carbonate electrolytes. Our results indicate that esters and ureas-based electrolytes are similarly stabilized by FEC, and have very similar capacity retentions and Coulombic efficiencies to the state-of-the-art carbonate electrolyte. This study indicates the discovery of more efficient additives other than FEC is vital in developing an electrolyte that can successfully enable a silicon-anode battery.

25 ENERGY STORAGE↗

Significant Improvements to Si Calendar Lifetime Using Rapid Electrolyte Screening via Potentiostatic Holds

Silicon-based lithium-ion batteries exhibit severe time-based degradation resulting in poor calendar lives. This has been identified as the major impediment towards commercialization with cycle life considered a solved issue through nanosizing and protective coatings allowing over 1000 cycles of life to be achieved. In this work, rapid screening of sixteen electrolytes for calendar life extension of Si-rich systems (70 wt% Si) is performed using the voltage hold (V-hold) protocol. V-hold significantly shortens the testing duration over the traditional open circuit voltage reference performance test allowing us to screen electrolytes within a span of two months. We find a novel ethylene carbonate (EC) free electrolyte formulation containing lithium hexafluorophosphate (LiPF 6 ) salt, and binary solvent mix of fluoroethylene carbonate (FEC), ethyl methyl carbonate (EMC) that extends calendar life of Si cells as compared to conventional EC based electrolyte. Our coupled experimental-theoretical analysis framework provides a decoupling of the parasitic currents during V-hold, allowing us to extrapolate the capacity loss to predict semiquantitative calendar lifetimes. Subsequently, cycle aging and oxidative stability tests of the EC free system also show enhanced performance over baseline electrolyte.

25 ENERGY STORAGE↗

Practical stability limits of magnesium electrolytes

The development of a Mg ion based energy storage system could provide several benefits relative to today's Li-ion batteries, such as improved energy density. The electrolytes for Mg batteries, which are typically designed to efficiently plate and strip Mg, have not yet been proven to work with high voltage cathode materials that are needed to achieve high energy density. One possibility is that these electrolytes are inherently unstable on porous electrodes. To determine if this is indeed the case, the electrochemical properties of a variety of electrolytes were tested using a porous carbon coating on graphite foil and stainless steel electrodes. It was determined that the oxidative stability limit on these porous electrodes is considerably reduced as compared to those found using polished platinum electrodes. Furthermore, the voltage stability was found to be about 3 V vs. Mg metal for the best performing electrolytes. In conclusion, these results imply the need for further research to improve the stability of Mg electrolytes to enable high voltage Mg batteries.

25 ENERGY STORAGE↗

Preformed Anodes for High-Voltage Lithium-Ion Battery Performance: Fluorinated Electrolytes, Crosstalk, and the Origins of Impedance Rise

We report that preformation of graphite electrodes, in a highly fluorinated electrolyte, show exemplary performance when incorporated into LiNi 0.5 Mn 0.3 Co 0.2 O 2 //graphite cells (NMC//Gr) containing a traditional organic electrolyte. NMC//Gr cells, using preformed graphite electrodes, showed enhanced capacity and power retention as well as improved coulombic efficiencies. The increased performance was only observed with the use of specific electrolytes during the preforming step, where graphite electrodes, when preformed with the baseline organic carbonate electrolyte, did not show the same benefits. The identity of the preforming electrolyte was also observed to influence electrode crosstalk, where compounds generated at one electrode can affect the opposite electrode. The work herein presents both physical and electrochemical evidence of electrode crosstalk and reveals the beneficial effect of the preforming procedure in limiting the associated degradation mechanisms thereof. Lastly, the insights gained may lead to new methodologies for the design of electrochemically robust interfaces that can enabling high-voltage, lithium-ion batteries.

25 ENERGY STORAGE↗