SEARCH · Engineering Papers

Results for “distributed computation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

All sources NASA NTRS DOE OSTI

NASA NTRS1972

The theoretical and experimental investigations on multiple pure tone noise.

An investigation on multiple pure tone (MPT) noise is described. The model fan is operated, in Freon 12, in a closed loop acoustical facility. It has been found experimentally that the rotor relative Mach number and incidence angle are parameters important to the evolution of the MPT sound and the inlet duct length has a significant influence on the MPT sound emission. The experimental results are compared with a previous analysis. From the known blade nonuniformities of the model fan, the MPT distributions are computed. The analysis correctly predicts the frequency of the dominant multiple pure tone and sound pressures of the blade passing frequency noise and the dominant MPT that are in the same range as the experimental values.

Kantola, R. A.↗

NASA NTRS1973

Investigation of the dielectric waveguide modes in homostructure GaAs laser.

The investigation of the propagation modes in a homostructure GaAs laser and particularly of the spatial displacement of the TE and TM mode is reported. For this investigation, a homostructure GaAs laser was operated in an external optical cavity and experiments were performed where the resonator alignment was varied to displace the image of the p-n junction, formed in the optical cavity, from the p-n junction of the laser diode. The peak power of the laser radiation (which is in the TEM (sub 00) mode), the delay, the optical waveform, and the polarization were measured at room temperature for different cavity alignments. For the evaluation of the propagation modes the experimental results are correlated with the computed field distributions of the modes in a three-layer dielectric waveguide.

Philipp-Rutz, E. M.↗

NASA NTRS1974

The numerical calculation of laminar boundary-layer separation

Iterative finite-difference techniques are developed for integrating the boundary-layer equations, without approximation, through a region of reversed flow. The numerical procedures are used to calculate incompressible laminar separated flows and to investigate the conditions for regular behavior at the point of separation. Regular flows are shown to be characterized by an integrable saddle-type singularity that makes it difficult to obtain numerical solutions which pass continuously into the separated region. The singularity is removed and continuous solutions ensured by specifying the wall shear distribution and computing the pressure gradient as part of the solution. Calculated results are presented for several separated flows and the accuracy of the method is verified. A computer program listing and complete solution case are included.

Klineberg, J. M.↗

NASA NTRS1974

On laminar boundary-layer separation

Iterative finite-difference techniques are developed for integrating the boundary-layer equations, without approximation, through a region of reversed flow. The numerical procedures are used to calculate incompressible laminar separated flows and to investigate the conditions for regular behavior at the point of separation. Regular flows are shown to be characterized by an integrable saddle-type singularity that makes it difficult to obtain numerical solutions which pass continuously into the separated region. The singularity is removed and continuous solutions ensured by specifying the wall shear distribution and computing the pressure gradient as part of the solution. Calculated results are presented for a number of separated flows and the accuracy of the method is verified.

Klineberg, J. M.↗

NASA NTRS1975

Thickness noise of helicopter rotors at high tip speeds

A new formulation of helicopter rotor thickness, noise for hover and forward flight, is discussed. The parameters required for this formulation are rotor motion, planform and airfoil thickness distribution. A computer program has been developed to calculate the pressure signature due to blade thickness for a helicopter in arbitrary motion. Comparison with high-speed helicopter tests shows good agreement with calculations when the observer is in or near the horizontal plane in which the rotor disk lies. Characteristics of thickness noise are illustrated by numerical examples indicating strongly that the high-speed blade slap may be due primarily to the thickness effect. The methods of Deming and Arnoldi are discussed as the special cases of this technique.

Farassat, F.↗

NASA NTRS1975

A chemical model of the troposphere and stratosphere

A time-dependent, one-dimensional model of the coupled chemistry and vertical mixing of the atmosphere is used to compute the distribution for many atmospheric constituents of the troposphere and stratosphere. The model treats the photochemistry of the carbon-hydrogen-oxygen-nitrogen system and is (with the exception of H2O) self-consistent in the sense of requiring no assumptions regarding minor constituent distributions.

Stewart, R. W.↗

NASA NTRS1976

Field distribution in a thin lens

Quasi-optical formulation gives an optical field distribution by computing only two terms. First term represents geometrical optics effect, and second term represents diffraction effect; thus, mathematical expression is simplified, and considerable computer time is saved.

Chi, C. H.↗

NASA NTRS1976

Electrodynamics of long conducting tethers in the near-earth environment

An analytical approach was developed to evaluate the electrodynamic interactions affecting a thin, bare metallic wire moving in the ionosphere. The wire's diameter was smaller than the Debye length; therefore, the plasma sheath around the wire was taken into account in computing inducing drag force and torque. Computer programs were prepared for the numerical evaluation of mathematical functions that were required to compute the distribution of the potential along the wire and of the current in the wire. Numerical calculations based on this software are shown.

Dobrowolny, M.↗

NASA NTRS1975

Non-equilibrium one-dimensional two-phase flow in variable area channels

A one-dimensional nonequilibrium flow analysis has been formulated for a one component two phase flow. The flow is considered homogeneous and essentially isothermal. Phase change is assumed to occur at heterogeneous nucleation sites and the growth of the vapor bubbles is governed by heat conduction from the liquid to the bubble. The analysis adjusted for friction is applied to liquid nitrogen flow in a venturi and comparison is made with the NASA experimental results of Simoneau. Good agreement with the experiments is obtained when one assumes the effective activation energy for nucleus formation to be small but nonzero. The computed pressure distributions deviate from the experimental results in the throat region of the venturi in a manner consistent with centrifugal effects not accounted for in the one-dimensional theory. The results are shown to depend not only on cavitation number but on additional dimensionless parameters governing the nonequilibrium production and subsequent growth of nuclei.

Rohatgi, U. S.↗

NASA NTRS1976

Engineering flowfields and heating rates for highly swept wing leading edges

An engineering flow model is developed (and verified experimentally) which describes the flowfield that arises when a supersonic stream encounters a wedge/cylinder configuration whose angles are such that the flow includes only weak shock waves. A numerical code using the perfect gas relations is used to describe the flow in the plane of symmetry inboard of the shock interaction region. Theoretical surface-pressure and heat-transfer distributions are computed for freestream velocities ranging from 1167 to 7610 m/sec. Nondimensionalization of the heat-transfer rates in terms of local flow parameters produced a correlation of Stanton number as a function of the local Reynolds number, which is independent of the freestream flow conditions and of the surface temperature.

Bertin, J. J.↗

NASA NTRS1978

Design of a laminar-flow-control supercritical airfoil for a swept wing

An airfoil was analytically designed and analyzed for a combination of supercritical flow and laminar flow control (LFC) by boundary layer suction. A shockless inverse method was used to design an airfoil and an analysis method was used in lower surface redesign work. The laminar flow pressure distributions were computed without a boundary layer under the assumption that the laminar boundary layer would be kept thin by suction. Inviscid calculations showed that this 13.5 percent thick airfoil has shockless flows for conditions at and below the design normal Mach number of 0.73 and the design section lift coefficient of 0.60, and that the maximum local normal Mach number is 1.12 at the design point. The laminar boundary layer instabilities can be controlled with suction but the undercut leading edge of the airfoil provides a low velocity, constant pressure coefficients region which is conducive to laminar flow without suction. The airfoil was designed to be capable of lift recovery with no suction by the deflection of a small trailing edge flap.

Allison, D. O.↗

NASA NTRS1978

User's manual: Subsonic/supersonic advanced panel pilot code

Sufficient instructions for running the subsonic/supersonic advanced panel pilot code were developed. This software was developed as a vehicle for numerical experimentation and it should not be construed to represent a finished production program. The pilot code is based on a higher order panel method using linearly varying source and quadratically varying doublet distributions for computing both linearized supersonic and subsonic flow over arbitrary wings and bodies. This user's manual contains complete input and output descriptions. A brief description of the method is given as well as practical instructions for proper configurations modeling. Computed results are also included to demonstrate some of the capabilities of the pilot code. The computer program is written in FORTRAN IV for the SCOPE 3.4.4 operations system of the Ames CDC 7600 computer. The program uses overlay structure and thirteen disk files, and it requires approximately 132000 (Octal) central memory words.

Moran, J.↗

NASA NTRS1978

Adding stress plot function to NASTRAN

Stress plot function was developed and added to the NASTRAN level 15.5. Computed stress distribution can be displayed by this function, with vectors showing the principal stresses of the finite elements over the specified portions of the structure. NASTRAN is reviewed in the aspect of plotting capabilities. Stress tensor field is examined in preparation of stress display. Then the stress plot function as added to the NASTRAN is described. A sample plotout by this function is shown.

Katoh, S.↗

NASA NTRS1978

Two-dimensional separated wake modeling and its use to predict maximum section lift coefficient

A technique for computing the lift of separating multielement airfoils in incompressible flow is presented. The procedure employs repeated application of a panel method to solve for the separated wake displacement surface using entirely inviscid boundary conditions. Results are presented that compare computed pressure distributions with those measured in the wind tunnel for airfoils with one, two, and four elements with separation on each element. A method employing this technique is presented which shows promise in predicting airfoil section lift through stall.

Henderson, M. L.↗

NASA NTRS1978

Laser-zone growth in a Ribbon-To-Ribbon (RTR) process. Silicon sheet growth development for the large area sheet task of the low-cost solar array project

A new calculation of the effects of thermal stresses during growth on silicon ribbon quality is reported. Thermal stress distributions are computed for ribbon growth under a variety of temperature profiles. A growth rate of 55 cu cm/min with a single ribbon was achieved. The growth of RTR ribbon with a fairly uniform parallel dendritic structure was demonstrated. Results with two approaches were obtained for reducing the Mo impurity level in polycrystalline feedstock. Coating the Mo substrate with Si3N4 does not effect thermal shear separation of the polyribbon; this process shows promise of improving cell efficiency and also increasing the useful life of the molybdenum substrate. A number of solar cells were fabricated on RTR silicon grown from CVD feedstock.

Baghdadi, A.↗

NASA NTRS1978

High efficiency low cost solar cell power

A concept for generating high-efficiency, low-cost, solar-cell power is outlined with reference to solar cell parameters, optical concentrators, and thermal control procedures. A design for a 12.5-kw power module for space operation is discussed noting the optical system, spectrum splitter, light conversion system, cell cooling, power conditioner, and tracking mechanism. It is found that for an unconcentrated array, efficiency approaches 60% when ten or more bandgaps are used. For a 12-band system, a computer program distributed bandgaps for maximum efficiency and equal cell currents. Rigid materials and thin films have been proposed for optical components and prisms, gratings, and dichroic mirrors have been recommended for spectrum splitting. Various radiator concepts are noted including that of Weatherston and Smith (1960) and Hedgepeth and Knapp (1978). The concept may be suitable for the Solar Power Satellite.

Bekey, I.↗

NASA NTRS1978

Digital techniques for processing Landsat imagery

An overview of the basic techniques used to process Landsat images with a digital computer, and the VICAR image processing software developed at JPL and available to users through the NASA sponsored COSMIC computer program distribution center is presented. Examples of subjective processing performed to improve the information display for the human observer, such as contrast enhancement, pseudocolor display and band rationing, and of quantitative processing using mathematical models, such as classification based on multispectral signatures of different areas within a given scene and geometric transformation of imagery into standard mapping projections are given. Examples are illustrated by Landsat scenes of the Andes mountains and Altyn-Tagh fault zone in China before and after contrast enhancement and classification of land use in Portland, Oregon. The VICAR image processing software system which consists of a language translator that simplifies execution of image processing programs and provides a general purpose format so that imagery from a variety of sources can be processed by the same basic set of general applications programs is described.

Green, W. B.↗

NASA NTRS1980

A finite element method for the computation of transonic flow past airfoils

A finite element method for the computation of the transonic flow with shocks past airfoils is presented using the artificial viscosity concept for the local supersonic regime. Generally, the classic element types do not meet the accuracy requirements of advanced numerical aerodynamics requiring special attention to the choice of an appropriate element. A series of computed pressure distributions exhibits the usefulness of the method.

Eberle, A.↗