Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “coordination state”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Tribology of ceramics: Report of the Committee on Tribology of Ceramics

The current state of knowledge of ceramic surface structures, composition, and reactivity is reviewed. The tribological requirements of advanced mechanical systems now being deployed (in particular, heat engines) exceed the capabilities of traditional metallic-based materials because of the high temperatures encountered. Advanced ceramic materials for such applications are receiving intense scrutiny, but there is a lack of understanding of the properties and behavior of ceramic surfaces and the influence of processing on the properties of ceramics is described. The adequacy of models, ranging form atomic to macro, to describe and to predict ceramic friction and wear are discussed, as well as what is known about lubrication at elevated temperatures. From this analysis, recommendations are made for coordination, research, and development that will lead to better performance of ceramic materials in tribological systems.

Source record↗
NASA NTRS1999

An Airborne Scanning Laser Altimetry Survey of Long Valley, California

Between 28 September and 7 October 1995, we conducted an airborne laser altimetry experiment over the Long Valley caldera, California, in which each of two scanning laser altimeters (dubbed SLICER and RASCAL) were flown in a NASA T-39 jet aircraft. Operating concurrently were a Global Positioning System (GPS) guidance system and dual frequency receivers for precise navigation and post-flight calculation or the airplane trajectory relative to a ground station, and an inertial navigation system (INS) for attitude determination. Reduction of raw laser ranges requires merging the differential kinematic GPS aircraft trajectory and the INS data with the laser data, and determination of the atmospheric delay. Data geolocation consists of obtaining the centre location and the mean elevation within each footprint in a geodetic coordinate system. The elevation of Crowley Lake is recovered to an accuracy of approximately 3 cm or better from 3 km above ground level and crossover analysis indicates that the elevation estimates are consistent from pass to pass. We test our geolocation procedures by comparing laser-derived elevations with those determined in situ for recognizable ground features. A comparison of laser and GPS-derived positions shows that the horizontal accuracy is better than the diameter of the footprint and vertical accuracy is within the error inherent in the range measurement. A comparison of SLICER elevation data with digital elevation models (DEMs) of the region shows that the DEM data provides surface topography to within stated accuracy limits. Although research continues to utilize the full potential of laser altimetry data, our results constitute a successful demonstration that the technique may be used to perform geodetic monitoring of surface topographic changes.

Hofton, M. A.↗
NASA NTRS2008

Summary of the Science Performed Onboard the International Space Station within the United States Orbital Segment during Increments 16 and 17

With the launch of the STS-122 on February 7, 2008, which delivered the European Columbus science module and the upcoming STS-124 flight, which will deliver the Japanese Kibo science module in May 2008, the International Space Station will become truly International with Europe and Japan joining the United States of America and Russia to perform science on a continuous basis in a wide spectrum of science disciplines. The last science module, Kibo, of the United States Orbital Segment (USOS) will be mated to the station on time to celebrate its first decade in low Earth orbit in October 2008 (end of Increment 17), thus ushering in the second decade of the station with all the USOS science modules mated and performing science. The arrival of the Kibo science module will also mark continuous human presence on the station for eighty eight (88) months, and, with the addition of the ESA science module during the STS-122 flight, the USOS will be made up of four space agencies: CSA, ESA, JAXA and NASA, spanning three continents. With the additional partners coming onboard with different research needs, every effort is being made to coordinate science across the USOS segment in an integrated manner for the benefit of all parties. One of the objectives of this paper is to discuss the integrated manner in which science planning/replanning and prioritization during the execution phase of an increment is being done. The main focus, though, of this paper is to summarize and to discuss the science performed during Increments 16 and 17 (October 2007 to October 2008). The discussion will focus mainly on the primary objectives of each investigation and their associated hypotheses that were investigated during these two Increments. Also, preliminary science results will be discussed for each of the investigation as science results availability permit. Additionally, the paper will briefly touch on what the science complement for these two increments was and what was actually accomplished due to real time science implementation and constraints. Finally, the paper will briefly discuss the science research complements for the next three Increments: Increments 18 to 20, in order to preview how much science might be accomplished during these three upcoming Increments of the station next decade.

Jules, Kenol↗
NASA NTRS2015

Assessment of a National Airspace System Airborne Rerouting Tool

This paper presents the assessment of a National Airspace System airborne rerouting tool. The tool implements NASA’s Dynamic Weather Routes concept for wind-corrected flying-time savings during convective weather activity. A description of the system, as applicable to the entire United States airspace is provided, and results are presented demonstrating benefits of such a system from various Centers and airlines’ perspectives. Three cases for selection of reroute-return capture fix, which prevent unrealistically large controller clearances are presented. Results are shown for potential time- and fuel-savings (over 134,000 minutes and 4.2 million lbs. of fuel for over 35,000 proposed reroutes) and sector congestion reduction (over 121 hours in congested sectors) for all 20 Centers. The data used were for 30 days with highest delays attributable to convective weather from April to October of 2014. Other results show the evaluation of the maneuver or reroute start point (a parameter representing the amount of coordination time needed), which highlight the need for a controller-pilot data link. A data link would help achieve higher savings. The results for persistence time, beyond which the time-savings dwindle quickly, help determine the maximum coordination time required for each Center. Finally, an assessment from a current National Operations Manager at the Air Traffic Control System Command Center of the FAA is documented. Those suggestions could improve the efficiency of the air transportation system, especially with the expected improvements in the traffic flow management infrastructure. Currently, one industry partner and one airline are assessing this technology for commercial operational use.

Benefits Assessment↗
NASA NTRS2002

Operational Limitations of the High Rate Frame Multiplexer (HRFM) Onboard the International Space Station(ISS)-and How These Limitations Affect Payload Developers (PDs) and International Partners (IPs)

The data system onboard the United States Operating Segment (USOS) of the ISS is currently used to capture, route, record and downlink high-rate science data from experiments inside the US Lab. Once NASDA's Japanese Experiment Module (JEM) and ESA's Attached Pressurized Module (APM) are launched - in the 2004 to 2005 timeframe - data from these facilities will also be routed to the ground using the USOS data system. A critical component of the USOS data system is the High Rate Frame Multiplexer (HRFM). The HRFM combines multiple data/video inputs and combines them into one data stream. This Ku-band data stream is then routed through the Tracking and Data Relay Satellite (TDRS) system to the ground. The Data Management Coordinator (DMC) - located at the Marshall Space Flight Center's Payload Operations Center (POC) - is responsible for commanding and controlling the HRFM. The HRFM can multiplex a maximum of eight digital data sources and four digital video sources. Thus far, this limitation has not been constraining to operations. However, once the JEM and APM are integrated, the HRFM limitations will become a major constraint to science operations onboard. The purpose of this paper is to characterize the limitations of the HRFM and to explain how these limitations can be successfully managed. With this information, Payload Developers and International Partners will be able to more effectively utilize the data systems onboard the ISS. Ultimately, more science data can be captured and downlinked to Flight Controllers and Scientists on the ground.

Mixson, Charles D.↗
NASA NTRS2006

Desert Research and Technology Studies 2005 Report

During the first two weeks of September 2005, the National Aeronautics and Space Administration (NASA) Johnson Space Center (JSC) Advanced Extravehicular Activity (AEVA) team led the field test portion of the 2005 Research and Technology Studies (RATS). The Desert RATS field test activity is the culmination of the various individual science and advanced engineering discipline areas year-long technology and operations development efforts into a coordinated field test demonstration under representative (analog) planetary surface terrain conditions. The purpose of the RATS is to drive out preliminary exploration concept of operations EVA system requirements by providing hands-on experience with simulated planetary surface exploration extravehicular activity (EVA) hardware and procedures. The RATS activities also are of significant importance in helping to develop the necessary levels of technical skills and experience for the next generation of engineers, scientists, technicians, and astronauts who will be responsible for realizing the goals of the Constellation Program. The 2005 Desert RATS was the eighth RATS field test and was the most systems-oriented, integrated field test to date with participants from NASA field centers, the United States Geologic Survey (USGS), industry partners, and research institutes. Each week of the test, the 2005 RATS addressed specific sets of objectives. The first week focused on the performance of surface science astro-biological sampling operations, including planetary protection considerations and procedures. The second week supported evaluation of the Science, Crew, Operations, and Utility Testbed (SCOUT) proto-type rover and its sub-systems. Throughout the duration of the field test, the Communications, Avionics, and Infomatics pack (CAI-pack) was tested. This year the CAI-pack served to provide information on surface navigation, science sample collection procedures, and EVA timeline awareness. Additionally, 2005 was the first year since the Apollo program that two pressurized suited test subjects have worked together simultaneously. Another first was the demonstration of recharge of cryogenic life support systems while in-use by the suited test subjects. The recharge capability allowed the simulated EVA test duration to be doubled, facilitating SCOUT proto-type rover testing. This paper summarizes Desert RATS 2005 test hardware, detailed test objectives, test operations and test results.

Ross, Amy J.↗
NASA NTRSDate not supplied

Stress-Activated Positive Holes (O− in a Matrix of O2–) Cause DNA Damage in Surface-Dwelling Organisms: Unveiling Mutation-Induced Secrets of Nature

Peroxy defects consist of pairs of tightly bonded oxygen anions in the –1 valence state such as in O3X/OO\YO3 with X, Y = Si4+, Al3+ etc. They commonly occur in igneous, metamorphic and many sedimentary rocks. When such rocks are stressed by tectonic forces, peroxy defects break up, releasing highly mobile electronic charge carriers: defect electrons in the O2– sublattice, i.e. unbound O–, known as “positive holes”, h•. The h• can flow out of stressed rock volumes, spreading far and wide, causing electric currents and electrochemical reactions. This study explores how the h• impact the electron flow in the electron transport chain (ETC) of organisms on the surface of rocks such as gabbro and granite. We found that, by forming hydroxyl radicals and superoxide anions, the h• disrupt the in vivo coordination of reduction-oxidation reactions that are essential for the timing of the redox cycle. Our observations show that stress activation of h• delays the sprouting of certain plant seeds and impedes the growth of yeast cultures, Saccharomyces cerevisiae. The h• induce mutations and affect plant development as evidenced by reduced stem length and leaf size. At the same time, the h• serve as a source of abiotic oxidation, capable of forming various organic compounds in situ. Through the generation of radical species that create new carbon-carbon bonds the h• facilitate the abiotic synthesis of hydrocarbons and other organic molecules essential to life, including porphyrins. Our findings highlight the intricate interplay between positive holes, redox timing, and biological processes, revealing their significant role in influencing the growth and development of organisms in tectonically stressed crustal environments. Understanding these effects enhances our broader comprehension of redox biology and the influence of environmental factors on cellular development in natural settings.

astrobiology↗
NASA NTRS1991

Pulsed response of a TWT

The consequence of frequency domain multiple access channelization in a satellite communications system is that the ground- and space-based components often are required to operate in a linear region to prevent the generation of distortion signals. Components of a time division multiple access (TDMA) satellite system, such as a traveling-wave tube (TWT), can operate in the highest output power state because the channelization technique is relatively insensitive to the distortions resulting from saturated operation. A 30 GHz TWT was tested to determine the suitability of such a device in a TDMA system. Testing was focused on the ability of the TWT's output signal to rise up to full power at the leading edge of TDMA bursts, simulated by a pulse train. A peak power meter was used to display and measure the pulsed signal waveform. Measurements on the TWT output pulse rise time indicate that the TWT lengthened the rise time by 10 to 20 ns. Imposing modulator turn on timing that precedes the data burst by the TWT rise time is a logical approach to coordination of the two subsystem specification.

May, Brian D.↗
NASA NTRS2014

Clearance Analysis of Node 3 Aft CBM to the Stowed FGB Solar Array

In early 2011, the ISS Vehicle Configuration Office began considering the relocation of the Permanent Multipurpose Module (PMM) to the aft facing Common Berthing Mechanism (CBM) on Node 3 to open a berthing location for visiting vehicles on the Node 1 nadir CBM. In this position, computer-aided design (CAD) models indicated that the aft end of the PMM would be only a few inches from the stowed Functional Cargo Block (FGB) port solar array. To validate the CAD model clearance analysis, in the late summer of 2011 the Image Science and Analysis Group (ISAG) was asked to determine the true geometric relationship between the on-orbit aft facing Node 3 CBM and the FGB port solar array. The desired measurements could be computed easily by photogrammetric analysis if current imagery of the ISS hardware were obtained. Beginning in the fall of 2011, ISAG used the Dynamic Onboard Ubiquitous Graphics (DOUG) program to design a way to acquire imagery of the aft face of Node 3, the aft end-cone of Node 1, the port side of pressurized mating adapter 1 (PMA1), and the port side of the FGB out to the tip of the port solar array using cameras on the Space Station Remote Manipulator System (SSRMS). This was complicated by the need to thread the SSRMS under the truss, past Node 3 and the Cupola, and into the space between the aft side of Node 3 and the FGB solar array to acquire more than 100 images from multiple positions. To minimize the number of SSRMS movements, the Special Purpose Dexterous Manipulator (SPDM) would be attached to the SSRMS. This would make it possible to park the SPDM in one position and acquire multiple images by changing the viewing orientation of the SPDM body cameras using the pan/tilt units on which the cameras are mounted. Using this implementation concept, ISAG identified four SSRMS/SPDM positions from which all of the needed imagery could be acquired. Based on a photogrammetric simulation, it was estimated that the location of the FGB solar array could be measured within an accuracy of about 1 in. in each axis relative to the ISS Analysis Coordinate System (ISSACS). In October 2011, a proposed image-acquisition plan was drafted by ISAG and released for review. The ISS Robotics flight control team (ROBO) proposed minor changes to SPDM positions 1 and 4 to meet ISS proximity requirements. The updated image acquisition plan and draft chit were presented to and approved by the Systems Working Group (SWG) November 18 and were sent to the Vehicle Configuration Board (VCB) in early December 2011. Working with ROBO on 3 successive days (February 21, 22, and 23), ISAG collected 161 images of the ISS. Approximately 40 images were collected from each of the four different SSRMS/SPDM positions, with each set mapping the region from the Node 3 end cone, across Node 1, along the forward port side portion of the FGB, and out the port side FGB solar arrays. From this imagery, the best 80 images were selected for use in the analysis. The images were radiometrically enhanced to improve color and contrast and loaded into the FotoG analysis software along with the camera parameters and control data, which consisted of the coordinates for 54 handrail attachment bolts on the aft face of Node 3, in the ISSACS coordinate system. The results of this analysis produced the measured coordinates of 116 points distributed across the face of the FGB solar array panels (see figure 3) along with propagated uncertainty estimates in each coordinate axis. These results were sent to the ISS Vehicle Configuration Office, which sent them to the Configuration Analysis Modeling and Mass Properties (CAMMP) team for comparison with the Russian-provided CAD model for the retracted FGB solar arrays. The CAMMP analysis unexpectedly showed that the measured location of the port FGB solar array was up to 41-in. further outboard than the design and was slightly twisted about its rotational axis. The unexpected comparison results produced some initial concern regarding the accuracy of the photogrammetric measurements. To verify the measured results, ISAG personnel conducted a second analysis using just the imagery of the solar arrays in an arbitrary coordinate system defined by the three corner points of the inboard-most panel, with the design distance between points A1 and A10 as the only scale. The new measurements agreed with the original results to within less than 1 in. RMS in each axis, confirming the original solar array measurements. ISAG produced a final report for the ISS Vehicle Configuration Office documenting an apparent anomaly in the retracted configuration of the port FGB solar arrays. A copy of the measurement report was translated and sent to the Russian Space Agency. During a Vehicle Integrated Performance and Resources (VIPeR) teleconference September 24, 2012, the Russians acknowledged receipt of a translated copy of the ISAG report. The Russian representative stated that the head of the solar array design team claimed that the measured configuration was impossible unless the structure was physically broken. The Russians acknowledged that they had no expertise in photogrammetry, so the analysis technique employed was a "black box" to them, and they did not know how to use the ISAG results. They asked for a single image in which the overextension of the port solar array could be obviously seen. On November 10, 2012, during a face-to-face meeting with their Russian counterparts at JSC, ISAG presented nadir-view imagery of the FGB acquired during Space Shuttle rendezvous. Using the known width of the pressurized portion of the FGB as a scale, this analysis clearly showed that the port FGB solar array was extended outboard further than the Russian design for the retracted solar array.

Liddle, Donn↗
NASA NTRS1994

Self-consistent steady state model of the low-latitude boundary layer

Results are presented from a steady state numerical model of the low-latitude boundary layer (LLBL) on closed field lines and its coupling to the dayside auroral ionosphere. In the model the boundary layer approximation is used, the result being that inertial forces are taken into account only in the main flow direction (-x) where they are balanced by pressure forces, j x B forces, and viscous forces. Motion in the transverse directions (y and z) is treated kinematically, the force balances in these two directions being purely static. Computationally, the model is two dimensional, describing the motion of plasma and frozen-in magnetic field in the equatorial (xy) plane but allowing for lowest-order polynomial variation of some quantities with the coordinate (z) perpendicular to that plane. The plasma expands and compresses isentropically; the magnetic field is calculated self-consistently, which leads to approximately parabolic field line shape in planes parallel to the magnetopause (the xz plane), with maximum field curvature near the magnetopause edge of the LLBL. Coupling to the ionosphere via region 1 field-aligned currents is included. The effects of the ionosphere are represented by two parallel resistive plates at fixed height above and below the equatorial plane. The model can be used to investigate the influence of various physical parameters, for example, viscous and magnetic Reynolds numbers, and of boundary conditions at the magnetopause and in the magnetosphere on the LLBL development in the -x direction. Special attention is given to viscous effects which, under suitable circumstances, lead to a region 1 current that first increases and then reduces with increasing longitude away from local noon. Asymptotic matching of the antisunward motion of the cool LLBL plasma to sunward convection of hot plasma in the magnetosphere is illustrated along with the entrainment of magnetospheric plasma by the antisunward LLBL flow.

Drakou, E.↗
NASA NTRS1999

3D-Stereoscopic Analysis of Solar Active Region Loops: SoHo/EIT Observations at Temperatures of 1.5-2.5 MK - 2

In this paper we study the three-dimensional (3D) structure of hot (T(sub e) approximately equals 1.5 - 2.5 MK) loops in solar active region NOAA 7986, observed on 1996 August 30 with the Extreme-ultraviolet Imaging Telescope (EIT) onboard the Solar and Heliospheric Observatory (SoHO). This complements a first study on cooler (T(sub e) approximately equals 1.0 - 1.5 MK) loops of the same active region, using the same method of Dynamic Stereoscopy to reconstruct the 3D geometry. We reconstruct the 3D-coordinates x(s), y(s), z(s), the density n(sub e)(s), and temperature profile T(sub e)(s) of 35 individual loop segments (as function of the loop coordinate s) using EIT 195 A and 284 A images. The major findings are: (1) All loops are found to be in hydrostatic equilibrium, in the entire temperature regime of T(sub e) = 1.0 - 2.5 MK; (2) The analyzed loops have a height of 2-3 scale heights, and thus only segments extending over about one vertical scale height have sufficient emission measure contrast for detection; (3) The temperature gradient over the lowest scale height is of order dT/ds is approximately 1 - 4 K/km; (4) The radiative loss rate is found to exceed the conductive loss rate by about two orders or magnitude, making thermal conduction negligible to explain the temperature structure of the loops; (5) A steady-state can only be achieved when the heating rate E(sub H) matches the radiative loss rate in hydrostatic equilibrium, requiring a heat deposition length lambda(sub H) of the half density scale height lambda, predicting a scaling law with the loop base pressure, EH varies as p(sub 0 exp 2). This favors coronal heating mechanisms that operate near the loop footpoints; (6) We find a reciprocal correlation between the loop pressure p(sub 0) and loop length L, i.e. p(sub 0) varies as 1/L, implying a scaling law of the steady-state requirement with loop length, i.e. E(sub H ) varies as 1/L(exp 2). The heating rate shows no correlation with the loop-aligned magnetic field component B(sub z) at the footpoints, but is correlated with the azimuthal field B(sub phi) = Bz(RDelta Phi/L) of a twisted loop, and is thus consistent with heating mechanisms based on field-aligned currents.

Aschwanden, Markus J.↗
NASA NTRS1999

Exhaust Nozzle Materials Development for the High Speed Civil Transport

The United States has embarked on a national effort to develop the technology necessary to produce a Mach 2.4 High Speed Civil Transport (HSCT) for entry into service by the year 2005. The viability of this aircraft is contingent upon its meeting both economic and environmental requirements. Two engine components have been identified as critical to the environmental acceptability of the HSCT. These include a combustor with significantly lower emissions than are feasible with current technology, and a lightweight exhaust nozzle that meets community noise standards. The Enabling Propulsion Materials (EPM) program will develop the advanced structural materials, materials fabrication processes, structural analysis and life prediction tools for the HSCT combustor and low noise exhaust nozzle. This is being accomplished through the coordinated efforts of the NASA Lewis Research Center, General Electric Aircraft Engines and Pratt & Whitney. The mission of the EPM Exhaust Nozzle Team is to develop and demonstrate this technology by the year 1999 to enable its timely incorporation into HSCT propulsion systems.

Grady, J. E.↗
NASA NTRS2008

NASA In-Situ Resource Utilization (ISRU) Technology and Development Project Overview

Since the Vision for Space Exploration (VSE) was released in 2004, NASA, in conjunction with international space agencies, industry, and academia, has continued to define and refine plans for sustained and affordable robotic and human exploration of the Moon and beyond. With the goal of establishing a lunar Outpost on the Moon to extend human presence, pursue scientific activities, use the Moon to prepare for future human missions to Mars, and expand Earth s economic sphere, a change in how space exploration is performed is required. One area that opens up the possibility for the first time of breaking our reliance on Earth supplied consumables and learn to live off the land is In-Situ Resource Utilization (ISRU). ISRU, which involves the extraction and processing of space resources into useful products, can have a substantial impact on mission and architecture concepts. In particular, the ability to make propellants, life support consumables, and fuel cell reagents can significantly reduce the cost, mass, and risk of sustained human activities beyond Earth. However, ISRU is an unproven capability for human lunar exploration and can not be put in the critical path of lunar Outpost success until it has been proven. Therefore, ISRU development and deployment needs to take incremental steps toward the desired end state. To ensure ISRU capabilities are available for pre-Outpost and Outpost deployment by 2020, and mission and architecture planners are confident that ISRU can meet initial and long term mission requirements, the ISRU Project is developing technologies and systems in three critical areas: (1) Regolith Excavation, Handling and Material Transportation; (2) Oxygen Extraction from Regolith; and (3) Volatile Extraction and Resource Prospecting, and in four development stages: (I) Demonstrate feasibility; (II) Evolve system w/ improved technologies; (III) Develop one or more systems to TRL 6 before start of flight development; and (IV) Flight development for Outpost. To minimize cost and ensure that ISRU technologies, systems, and functions are integrated properly into the Outpost, technology development efforts are being coordinated with other development areas such as Surface Mobility, Surface Power, Life Support, EVA, and Propulsion. Lastly, laboratory and field system-level tests and demonstrations will be performed as often as possible to demonstrate improvements in: Capabilities (ex. digging deeper); Performance (ex. lower power); and Duration (ex. more autonomy or more robustness). This presentation will provide the status of work performed to date within the NASA ISRU project with respect to technology and system development and field demonstration activities, as well as the current strategy to implement ISRU in future robotic and human lunar exploration missions.

Sanders, Gerald B.↗
NASA NTRS2010

Space Weather Products at the Community Coordinated Modeling Center

The Community Coordinated Modeling Center (CCMC) is a US inter-agency activity aiming at research in support of the generation of advanced space weather models. As one of its main functions, the CCMC provides to researchers the use of space science models, even if they are not model owners themselves. The second CCMC activity is to support Space Weather forecasting at national Space Weather Forecasting Centers. This second activity involves model evaluations, model transitions to operations, and the development of space weather forecasting tools. Owing to the pace of development in the science community, new model capabilities emerge frequently. Consequently, space weather products and tools involve not only increased validity, but often entirely new capabilities. This presentation will review the present state of space weather tools as well as point out emerging future capabilities.

Hesse, Michael↗
NASA NTRS2015

Superboom Caustic Analysis and Measurement Program (SCAMP) Final Report

The objectives of the Superboom Caustic Analysis and Measurement (SCAMP) Program were to develop and validate, via flight-test measurements, analytical models for sonic boom signatures in and around focal zones as they are expected to occur during commercial aircraft transition from subsonic to supersonic flight, and to apply these models to focus boom prediction of low-boom aircraft designs. The SCAMP program has successfully investigated sonic boom focusing both analytically and experimentally, while gathering a comprehensive empirical flight test and acoustic dataset, and developing a suite of focused sonic boom prediction tools. An experimental flight and acoustic measurement test was designed during the initial year of the SCAMP program, with execution of the SCAMP flight test occurring in May 2011. The current SCAMP team, led by Wyle, includes partners from the Boeing Company, Pennsylvania State University, Gulfstream Aerospace, Eagle Aeronautics, and Central Washington University. Numerous collaborators have also participated by supporting the experiment with human and equipment resources at their own expense. The experiment involved precision flight of a McDonnell Douglas (now Boeing) F-18B executing different maneuvers that created focused sonic booms. The maneuvers were designed to center on the flight regime expected for commercial supersonic aircraft transonic transition, and also span a range of caustic curvatures in order to provide a variety of conditions for code validations. The SCAMP experiment was designed to capture concurrent F-18B on-board flight instrumentation data, high-fidelity ground-based and airborne acoustic data, and surface and upper air meteorological data. Close coordination with NASA Dryden resulted in the development of new experimental instrumentation and techniques to facilitate the SCAMP flight-test execution, including the development of an F-18B Mach rate cockpit display, TG-14 powered glider in-flight sonic boom measurement instrumentation and "Where's the Focus?" (WTF) software for near-real time way-point computation accounting for local atmospherics. In May 2011, 13 F-18B flights were conducted during 5 flying days over a 2 week period. A densely populated 10,000 ft-long ground acoustic array with 125-ft microphone spacing was designed to capture pre-, focus, and post-focus regions. The ground-based acoustic array was placed in a nominally east-west orientation in the remote Cuddeback lakebed region, north of Edwards AFB. This area was carefully selected to avoid placing focused booms on populated areas or solar power facilities. For the SCAMP measurement campaign, approvals were obtained to temporarily extend the Black Mountain supersonic corridor northward by three miles. The SCAMP flight tests successfully captured 70 boom events, with 61 focus passes, and 9 calibration passes. Seventeen of the focus passes and three of the calibration passes were laterally offset; with the others being centerline flights. Airborne incoming sonic boom wave measurements were measured by the TG-14 for 10 of the F-18B flight passes including one maximum focus signature, several N-u combinations, several overlapped N-u signatures, and several evanescent waves. During the 27-month program, the SCAMP team developed a suite of integrated computer codes with sonic boom focusing predictive capabilities: PCBoom, Lossy Nonlinear Tricomi Equation Method (LNTE) and the Nonlinear Progressive wave Equation (NPE) method. PCBoom propagates the rays through the atmosphere and, in addition to legacy focus signature prediction based on the Gill-Seebass method, provides input source characteristics and propagation parameters to LNTE and NPE. LNTE, a Tricomi solver that incorporates atmospheric losses, computes the focus signature at the focus, and computes the focus signature in the vicinity of the focal zone, including the evanescent and post-focus zones. LNTE signature auralization from low-boom vehicle designs has been demonstrated in the NASA Langley Interior Effects Room (IER). The NPE has also been validated for use in prediction of focused ground boom signatures in sonic boom focal zones. The NPE formulation has the capability to incorporate atmospheric turbulence in the predictions. This has been applied to sonic boom propagation in the past. Prediction of turbulence effects on focal zone signatures was not, however, explored during the SCAMP program.

Page, Juliet↗
NASA NTRSDate not supplied

Evaluation of the Recent Improvements of the Nowcast of Aerospace Ionizing Radiation System (NAIRAS)

The Nowcast of Aerospace Ionizing Radiation System (NAIRAS) model is a real-time, global, physics-based model used to assess radiation exposure now running in real-time and in run on request (RoR) mode at NASA Goddard’s Community Coordinated Modeling Center. NAIRAS was recently updated to extend the galactic cosmic ray (GCR) model to include ultra-heavy nuclei (Z=29-92, A=64-238) for single event effects assessment from high linear energy transfer processes, to expand the geomagnetic cutoff rigidity model to use the either the TS05 (Tsyganenko and Sitnov, 2005), T89 (Tsyganenko, 1989), or the International Geomagnetic Reference Field model (IGRF) magnetic field models, and to improve the solar energetic particle (SEP) proton spectral fitting to better represent relativist protons during ground level enhancements. Here, we evaluate the recent NAIRAS improvements for a range of conditions. First, we demonstrate the effect of choice in magnetic field model to the NAIRAS computed dosimetric quantities for a United States domestic flight and a transatlantic flight during the May 11, 2024 SEP event. Second, the effect of ultra-heavy ions on SEP dose rate is examined for two different flight trajectories during the top SEP events. Lastly, the effect of ultra-heavy ions on NAIRAS computed GCR dose rates at solar minimum and maximum is demonstrated.

Daniel B Phoenix↗
NASA NTRS1980

Development of alternative data analysis techniques for improving the accuracy and specificity of natural resource inventories made with digital remote sensing data

An investigation was conducted into ways to improve the involvement of state and local user personnel in the digital image analysis process by isolating those elements of the analysis process which require extensive involvement by field personnel and providing means for performing those activities apart from a computer facility. In this way, the analysis procedure can be converted from a centralized activity focused on a computer facility to a distributed activity in which users can interact with the data at the field office level or in the field itself. A general image processing software was developed on the University of Minnesota computer system (Control Data Cyber models 172 and 74). The use of color hardcopy image data as a primary medium in supervised training procedures was investigated and digital display equipment and a coordinate digitizer were procured.

Lillesand, T. M.↗
NASA NTRS1989

Multidisciplinary Expert-aided Analysis and Design (MEAD)

The MEAD Computer Program (MCP) is being developed under the Multidisciplinary Expert-Aided Analysis and Design (MEAD) Project as a CAD environment in which integrated flight, propulsion, and structural control systems can be designed and analyzed. The MCP has several embedded computer-aided control engineering (CACE) packages, a user interface (UI), a supervisor, a data-base manager (DBM), and an expert system (ES). The supervisor monitors and coordinates the operation of the CACE packages, the DBM; the ES, and the UI. The DBM tracks the control design process. Models created or installed by the MCP are tracked by date and version, and results are associated with the specific model version with which they were generated. The ES is used to relieve the control engineer from tedious and cumbersome tasks in the iterative design process. The UI provides the capability for a novice as well as an expert to utilize the MCP easily and effectively. The MCP version 2(MCP-2.0) is fully developed for flight control system design and analysis. Propulsion system modeling, analysis, and simulation is also supported; the same is true for structural models represented in state-space form. The ultimate goal is to cover the integration of flight, propulsion, and structural control engineering, including all discipline-specific functionality and interfaces. The current MCP-2.0 components and functionality are discussed.

Hummel, Thomas C.↗