Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Novel Fuel Form Fabrication

Novel fuel form fabrication efforts have focused on casting of smaller diameter fuels in order to show the feasibility of the FAST test and the incorporation of a FCCI barrier either integral to the fuel or within the cladding tube. Casting of small diameter fuel slugs proved to be feasible at least one pin at a time using vacuum assisted arc casting. Integration of an integral FCCI barrier is also feasible although additional refinement will be necessary. If a sodium bonded fuel is employed, a more simple FCCI barrier may be to incorporate a thin barrier of material in the cladding before the sodium and fuel are loaded. Experiments have shown that sodium bonding of the barrier material and fuel is feasible.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Thermal Analysis Evaluations Using the Dry Cask Simulator

Different thermal analysis models were developed to simulate the dry cask simulator (DCS). The DCS is an experiment designed to simulate dry storage of a single boiling water reactor fuel assembly under a variety of heat loads and internal pressures. The DCS was set up and tested in both a vertical and horizontal configuration to determine cladding temperatures in vertical and horizontal dry cask storage systems. The models included a detailed STAR-CCM+ model with the fuel assembly geometry explicitly modeled, a porous STAR-CCM+ model with the fuel assembly geometry modeled as porous media region with calculated effective properties, and a COBRA-SFS model. COBRA-SFS is a thermal-hydraulic code developed for steady-state and transient analysis of multi assembly spent-fuel storage and transportation systems. STAR-CCM+ is a commercial computation fluid dynamics (CFD) code. Both a detailed and porous STARCCM+ model were developed to look at the effective thermal conductivity (keff) approach to modeling a fuel assembly. A keff fuel model is typically model in CFD thermal analyses due to its significantly lower computational costs. The models were run for a combination of low and high canister pressures (100 kPa and 800 kPa) and low and high internal heat loads (0.5 kW and 5 kW). Results from all three models were compared against experimental data taken from the DCS for the peak cladding temperature (PCT) and inlet air mass flow.

Suffield, Sarah R.↗
DOE OSTI2020

Heterogeneously integrated electro-optic modulator

In an electro-optical modulator, an electro-optical modulation layer is bonded to a cladding layer that overlies a substrate. A modulation zone waveguide is optically coupled to the electro-optical modulation layer and optically coupled to an I/O waveguiding structure embedded in the cladding layer. The I/O waveguiding structure is conformed to guide input light toward the modulation zone waveguide and to guide output light away from the modulation zone waveguide.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling and Analysis of the Transport and Disposal of Beryllium Moderator Blocks and Greater than Class C (GTCC) Waste

Radioactive waste in the United states is categorized based on its source, radioactivity, and security risk. The categorization method employed by the Nuclear Regulatory Committee (NRC) for low-level radioactive waste is not currently applied to any waste generated by the Department of Energy (DOE) or disposed of in DOE facilities. As a result, there is a large volume of DOE-generated waste with characteristics similar to the NRC’s “Greater than Class C” (GTCC) waste category which presently do not have a path for long-term disposal. Much of this waste cannot undergo the standard commercial disposition process due to it being categorized as Transuranic (TRU) waste under DOE guidelines, due to elevated concentrations of key fission products. Possible solutions to this dilemma are explored in the Environmental Impact Statement for the “Disposal of Greater-Than-Class-C Low Level Radioactive Wave” (EIS-0375). This paper analyzes several EIS possible paths for disposal for this “orphaned” waste. One example that highlights this categorization issue is the spent beryllium cladding that has been extracted from the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) throughout its operational lifetime. These beryllium blocks surround the reactor’s main chambers and components and serve as neutron moderators. This paper will use this particular waste form to analyze the economic and technological viability of transporting and storing this material under the storage and transportation criteria of the Waste isolation Pilot Plant (WIPP), which was deemed the most feasible disposition path according to the EIS. The example of this waste form used in this paper that highlights this categorization issue is the spent beryllium cladding extracted from Idaho National Laboratory’s (INL) Advanced Test Reactor (ATR). These beryllium blocks surround the reactor’s components and serve as neutron moderators, and thus have accumulated high concentration of high-activity transuranic isotopes. This paper analyzed the viability of transporting and storing this material under the storage and transportation criteria of the five primary disposition paths covered in EIS-0375. An array of calculations was carried out to assess the viability of the various disposition paths for the beryllium shipments as well as other waste shipments that fall within the GTCC category. Modeling with MCNP 6.2 was conducted to determine whether the beryllium blocks could be safely stored and transported within a 72-B cask; the standard shipping container for remote-handled, transuranic waste, while also meeting regulatory limits at various disposition paths. A cost analysis of the transportation and long-term disposal paths mentioned in the EIS was also carried out using available data and information from similar waste shipments. Lastly, a geochemical analysis of the various geological repository discussed in the EIS was also carried out using the Geochemists Workbench Release 14. Long-term disposal of the beryllium blocks at the Waste Isolation Pilot Plant (WIPP) proved to be the most cost-effective long-term disposition option of the ones considered in the EIS. A dose rate calculation at both contact and remote-handling distances indicate that the analyzed beryllium shipments should not exceed the exposure limits at any of the considered locations. Greater-than-class-C waste has been left in a regulatory state of limbo for years, resulting in backlogs of inventory across several research sites in the United States. Due to its high activity and presence of transuranic isotopes, it is imperative to ensure that it remains inaccessible and sequestered both in its short-term interim as well as a long-term geologic time scale. The information and assessments done in the paper could potentially serve as a reference for any future shipments of this waste form at the WIPP facility as well as other disposition paths that may be considered in the future.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Advanced Fuels Campaign Execution Plan

The Advanced Fuels Campaign (AFC) Execution Plan outlines the strategy, mission, scope, near-term and long-term goals, structure, and organization associated with nuclear fuels and materials research, development, and demonstration activities within the Department of Energy’s (DOE) Nuclear Fuel Cycle and Supply Chain (NFCSC) program. NFCSC has been given responsibility to identify and mature advanced fuel technologies for the DOE using a science-based approach, focused on developing a fundamental understanding of nuclear fuels and materials to drive development of integrated nuclear fuel and materials technology. This science-based approach combines theory, experiments, and multiscale modeling and simulation to achieve a predictive understanding of relevant behaviors ranging from fuel fabrication processes (and their resulting fuel microstructures) through fuel/cladding performance under irradiation (in contrast to more empirical, observation-based approaches frequently used in fuel performance modeling and fuel qualification). The traditional scope of AFC includes the evaluation and development of multiple fuel forms to support two fuel cycle options: once-through and full recycle. The word “fuel” is used generically to include conventional fuels, transmutation targets, and any associated cladding or duct materials. The once-through fuel cycle addresses advanced light water reactor fuels with enhanced performance, extended burnup, and reduced waste generation. In fiscal year (FY) 2012, AFC’s scope expanded to include research, development, and demonstration (RD&D) for light water reactor (LWR) fuels with enhanced accident tolerance. Fuel fabrication activities include the development of innovative methods to enhance process efficiencies, reduce waste, and improve control over as-fabricated fuel microstructural properties to achieve desired in-reactor performance. Using modern modeling and simulation approaches, the objective is to predict fresh fuel properties given the feedstock characteristics and fabrication process parameters. The performance-related activities include small-scale, in-reactor, and out-of-reactor phenomenological testing (distinct from, but synergistic with, integral prototypic testing) and extensive, quantitative characterization (focusing on characterization of fuel and cladding materials at the scale of microstructure) both before and after testing. Larger-scale, prototypic experiments are conducted in concert with phenomenological testing to drive a Fuel Development and Qualification program, incorporating a fundamental understanding of fuel behavior performance characteristics. Then, using the tools developed under the productive science-based approach, fuels will be optimized to meet specific performance requirements, thereby minimizing the need to repeatedly perform large-scale, integral experiments over a wide parametric range as a means of experimental exploration. Two significant initiatives are underway within AFC. First, a gap analysis completed in early FY 2019 identified critical irradiation testing needs that are lacking within the national light water reactor (LWR) fuels testbed since the shutdown of the Halden Reactor in 2018. The identified gaps are for instrumented, prototypic testing of LWR fuels, especially under boiling water reactor conditions, ramp conditions, and conditions leading to fuel failure; these needs exist for supporting current LWR fuels and their possible extension to higher burnups, but are especially urgent relative to near-term development and qualification of accident-tolerant fuels. Recommendations that resulted from the Halden Gap Analysis focused on enhancements at Advanced Test Reactor (ATR) and Transient Reactor Test Facility (TREAT) to fill gaps in testing capabilities relative to these needs. Second, a concerted effort to develop and demonstrate a systematic approach to accelerating the development, testing, and qualification of new fuel systems has been initiated. This is highlighted by a test strategy that combines the considerable advances in multiscale, mechanistic fuel modeling of recent years with a MiniFuel separate effects test program in the High Flux Isotope Reactor (HFIR) and a Fission Accelerated Steady-state Testing (FAST) semi-integral accelerated test program in ATR. This approach is being tested/demonstrated using the metallic fuel system, but if successful it is expected to be extensible to multiple fuel types and diverse applications. This document includes an overview of the NFCSC program, a definition of science-based development of nuclear fuels, near-term goals for Advanced LWR fuels (ALFs), and longer-term goals for Advanced Reactor Fuels (ARFs) RD&D. This includes the activities that will be conducted to achieve success toward the grand challenge, as well as the goals and milestones to be achieved over the next few decades of research and development. Long-term goals are based on the DOE Office of Nuclear Energ

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Results of the CHF-SERTTA In-Pile Transient Boiling Experiments at TREAT

To advance the current understanding of heat transfer between nuclear fuel rod cladding and the surrounding coolant under transient scenarios involving critical heat flux (CHF), the CHF-Static Environment Rodlet Transient Test Apparatus (CHFSERTTA), an in-pile experiment, was developed for and irradiated in the Transient Reactor Test (TREAT) facility at Idaho National Laboratory. The CHF-SERTTA experiment consists of a hollow, borated stainless steel rod submerged in a static water pool. The rod, heated via the (n, a) reaction in boron-10, was designed for investigating in-pile transient heat transfer between the rod surface and the coolant, avoiding the complexity of including the heat transfer between the fuel, gas gap, and cladding in typical light-water reactor (LWR) fuel rods. The instrumentation package for CHF-SERTTA focused on capturing those data that best describe the heat transfer behaviour between the rod and coolant. This paper outlines the CHFSERTTA experiment design and presents the initial results of the experiment campaign.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

POST-TEST EXAMINATIONS OF A LOCA SAMPLE FROM AN IRRADIATED HIGH-BURNUP PWR M5 FUEL ROD

A LOCA integral test with high burnup PWR M5 fuel rod was conducted in the Irradiated Fuel Examination Laboratory through the complete LOCA sequence: heating the LOCA sample to 300ºC and pressurizing the internal pressure to 8.27 MPa, heating at 5ºC/s from 300 to 1200ºC, holding in steam for 90s at 1200ºC, cooling at 3ºC/s to 800ºC, followed by water quench and rapid cooling to 100ºC. After LOCA testing, examinations, such as the fuel fragmentation analysis, burst and ballooning characterization, axial strain measurement, and microstructural examinations were performed. Metallographic examinations of an as-irradiated high burnup sample adjacent to the LOCA test sample revealed a bonding layer between the fuel and cladding. The posttest LOCA examinations indicates the corrosion layer formed during normal operations in the commercial reactor might provide a protection against the steam oxidation at high temperatures for test times performed in this work. The microstructure of the as-irradiated fuel is compared to the microstructure of the post-LOCA test fuel. Posttest LOCA examination on unirradiated post-tests Zr cladding samples was conducted, which served as baseline data for in cell testing with irradiated samples. The results obtained with irradiated PWR high burnup M5 fuel rad were compared to the LOCA test data obtained with irradiated BWR high burnup Zircaloy-2 fuel rod at Argonne national Laboratory.

Yan, Yong↗
DOE OSTI2021

Quantum cascade laser with monolithically integrated passive waveguide

A photonic integrated circuit device includes a passive waveguide section formed over a substrate, a quantum cascade laser (QCL) gain section formed over the substrate and adjacent to the passive waveguide section, and a taper section disposed between and in contact with each of the passive waveguide section and the QCL gain section. In some embodiments, the passive waveguide section includes a passive waveguide core layer disposed between a first cladding layer and a second cladding layer. In some examples, the QCL gain section includes a QCL active region disposed between a first confinement layer and a second confinement layer, where the QCL active region has a lower index of refraction than each of the first and second confinement layers. In some embodiments, the taper section is configured to optically couple the QCL gain section to the passive waveguide section.

Jung, Seungyong↗
DOE OSTI2022

Development of Accelerated Steady-state Test Capsule Experiments to Replicate EBR-II Fuel Behavior Using BISON Fuel Performance Analysis

Here in this work, BISON fuel performance calculations were performed to predict the fuel behavior of accelerated burnup U-Pu-Zr fuel, with temperature operation conditions of the fuel and the cladding mirroring conditions within EBR-II fuel pins. The temperature operating conditions within the FAST accelerated burnup rods were aimed at replicating EBR-II X447/X447A fuel surface and inner cladding surface temperatures. Due to the FAST capsule design, these temperatures can be replicated with fission rate densities being significantly increased. fuel performance modeling has not been assessed for novel experiments such as accelerated burnup utilizing the FAST capsule within ATR. This is an important step in understanding accelerated irradiation methods as many performance models are empirical models conforming to the results of PIE but do not always include physical models that would represent the changes in irradiation tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

System and method for plasmonic control of short pulses in optical fibers

The present disclosure relates to an optical waveguide system. The system has a first waveguide having a core-guide and a cladding material portion surrounding and encasing the core-guide to form a substantially D-shaped cross sectional profile with an exposed flat section running along a length thereof. The core-guide enables a core-guide mode for an optical pulse signal having a first characteristic, travelling through the core-guide. A material layer of non-linear material is used which forms a second waveguide. The material layer is disposed on the exposed flat section of the cladding material portion. The material layer forms a plasmonic device to achieve a desired coupling with the core-guide to couple optical energy travelling through the core-guide into the material layer to modify the optical energy travelling through the core-guide such that the optical energy travelling through the core-guide has a second characteristic different from the first characteristic.

Feigenbaum, Eyal↗
DOE OSTI2022

High-temperature and/or high pressure gas enclosure

A gas enclosure can include a refractory metal liner; a ceramic matrix composite cladding; and a diffusion barrier layer. The refractory metal liner is adapted to surround and enclose a gas to be contained within the gas enclosure. The diffusion barrier layer is disposed between the refractory metal liner and the ceramic matrix composite cladding.

Miao, Yinbin↗
DOE OSTI2022

Cold spray chromium coating for nuclear fuel rods

A zirconium alloy cladding tube for use in a water cooled nuclear reactor under normal operating conditions and under high temperature oxidation conditions is described. The cladding tube has a coating uniformly deposited thereon. The coating, which may be up to 300 microns thick, is selected from the group consisting of chromium, a chromium-based alloy, and combinations thereof.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Overview of the Water-Based RIA Testing in TREAT

A series of reactivity-initiated accident (RIA) commissioning tests have been completed with the static water capsule in the Transient Reactor Test (TREAT) Facility. The test campaign included a calibration test followed by five tests in the Static Environment Rodlet Transient Test Apparatus (SERTTA) capsule. The conditions varied from room temperature and pressure up to 200°C and 2.5 MPa with energy depositions varying between ~500-1100 J/gUO2. The series of tests allowed for a number of instrumentation qualifications and demonstrations including cladding thermometry, rodlet plenum pressure, cladding elongation, and an electro-impedance boiling detector. This paper documents the design of the capsule and highlight the results from the commissioning tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Overview of the Water-Based RIA Testing in TREAT

We have completed a series of reactivity-initiated accident commissioning tests with the static water capsule in the Transient Reactor Test Facility. The test campaign included a calibration test followed by five tests in the Static Environment Rodlet Transient Test Apparatus capsule. The conditions varied from room temperature and pressure up to 200°C and 2.5 MPa, with energy depositions varying between ~500–1100 J/gUO2. The series of tests allowed for a number of instrumentation qualifications and demonstrations, including cladding thermometry, rodlet plenum pressure, cladding elongation, and an electro-impedance boiling detector. This paper documents the design of the capsule and highlights the results from the commissioning tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Case Studies of Residential Façade Upgrades in Four Climate Zones

This paper reports on a project that explored the viability of insulation and window upgrades during siding retrofits in four case studies across the United States. Thousands of homes are re-sided every year, but only a fraction of consumers add insulation and upgrade the windows at the same time, even though a siding replacement is the ideal time to update the thermal performance of building enclosures. To better understand why more siding retrofits do not include insulation and window upgrades, research staff from several organizations collaborated with the U.S. Department of Energy on a multi-faceted research project that included a cost analysis, workforce analysis, market assessment, and contractor assessment. This paper will review four in-field case studies conducted with contractors actively engaged in home re-siding projects that agreed to add rigid insulation and window upgrades as part of their projects. Findings from the case studies will be presented including contractor perspectives, cost, and technical approaches on projects, located in multiple climate zones including Bellingham WA, Jackson MS, Kalamazoo MI, and Phoenix AZ. All projects involved adding continuous rigid insulation on the exterior walls and installation of new cladding. Cladding types varied from wood and metal to fiber cement, vinyl, and traditional stucco. All homes also received a window upgrade, although upgrades varied depending on the original condition of the windows and climate; upgrades included triple-pane windows, low-e storm windows, and exterior shading. Key findings including technical approaches, opportunities, barriers, and project cost will be presented.

re-siding, insulation, rigid insulation, exterior ↗
DOE OSTI2023

History of Melt-Processing System at SRNL

Capabilities of Melt Treatment Technology • Research Reactor Aluminum SNF (can extend to SS and Mg Clad Fuel) Aluminum Cladding Alloy • Typical thickness = 38 mils • Boehmite layer > 50 µm • Fuel Core • U -Alx, U308-Al; U3Si2-Al • Fabricated by cast extrusion or powder metallurgy • Enrichment = 20% to > 90% U235 • Typical Reactor Burnup = 5% to 55% • Thermal Output: <100 W, after 10 Years in storage

Adams, Thad M.↗
DOE OSTI2022

Thermal Model of Oxide Growth for Full Size Fuel Plate Experiments in the Advanced Test Reactor

The full-size plate number one (FSP-1) irradiation test designed for irradiation testing of plate type fuel is planned to be irradiated in the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). This FSP-1 experiment is a non-instrumented drop-in test where aluminum-clad fuel plates are cooled directly by the ATR Primary Coolant System (PCS) water. This experiment is one of a series of experiments being irradiated at ATR for the United States High Performance Research Reactor (USHPRR) program. This fueled experiment contains aluminum-clad fuel full-size plates consisting of monolithic U-10Mo. Previous thermal analyses have been documented concerning oxide growth [1] and thermal safety margins [2] for similar U-10Mo mini plate experiments. This analysis is part of the thermal safety analysis of the experiment to be irradiated in ATR. Departure from nucleate boiling ratio (DNBR) and flow instability ratio (FIR) have been calculated for the flow coastdown condition 2 and the reactivity insertion accident condition-2 (RIA2) transient. The purpose of this paper is to investigate the thermal margin of the fuel meat during a RIA2 transient when oxide has accumulated on the plate surfaces acting as an insulator.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Safety Considerations for Advanced Material Irradiation at the Advanced Test Reactor

The Advanced Test Reactor (ATR) is a light water reactor with aluminum-clad driver fuel. A primary mission of the ATR is to support the next generation of nuclear reactors. This support necessarily requires irradiation of advanced materials such as sodium, fuel salts, and metal eutectics. Irradiation of advanced materials in the ATR environment presents a challenge when completing accident analyses and demonstrating compliance to the Safety Analysis Report (SAR). Many advanced materials have the possibility to react with the ATR protective barriers such as the cladding or primary coolant system (PCS) boundary during postulated accident scenarios. Further, molten fuel experiments fall outside of the standard regulatory framework for dose consequence analyses. ATR is currently developing new safety analysis methods to support irradiation of advanced materials. The primary considerations for this development are 1) experiment containment design requirements, 2) primary coolant system response to an experiment containment failure, and 3) dose analyses for molten fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗