Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “carbon analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

The goal of the current work was to develop an analytical framework for design of composite struts using various levels of model fidelity. Rapid optimization trade studies were performed using low fidelity two-dimensional (2D) axisymmetric models with smeared composite properties. The optimum 2D model was compared with three-dimensional (3D) models with higher levels of fidelity in material property representation. Good agreement was found with all models. The buckling performance of the highest fidelity 3D model was found to be satisfactory for the intended loading conditions. An additional goal of this work was to perform an initial assessment of using automated fiber placement (AFP) and other advanced manufacturing methods to explore their feasibility for the fabrication of struts for lunar landers, strut-braced wings, and other aerospace components. The designs produced during this study are intended to be used to develop manufacturing demonstration units (MDU) that can be fabricated at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility at Langley Research Center (LaRC) and tested in lab facilities at LaRC.

carbon-epoxy↗
NASA NTRS2018

Axiomatic Design Based Analysis and Equivalent Mass Comparison of Alternate Air Revitalization Systems

A proposed Photocatalytic Air Processor (PAP) would combine two atmosphere revitalization functions for a crewed spacecraft, carbon dioxide removal and oxygen provision. The axiomatic design method is used to develop the general requirements and alternate system designs that combine these two atmosphere revitalization functions. There are two current atmosphere revitalization approaches. Short missions such as the space shuttle use lithium hydroxide (LiOH) to remove carbon dioxide and tanks to provide oxygen. The ISS (International Space Station) uses the CDRA (Carbon Dioxide Removal Assembly) to remove carbon dioxide and a Sabatier reactor and OGA (Oxygen Generation Assembly) to provide oxygen. The PAP could replace either of these combined systems, LiOH and oxygen tanks or the CDRA, Sabatier, and OGA. Axiomatic design is used to investigate these alternate high level system designs for atmosphere revitalization. The axiomatic design approach develops the requirements and design together from higher to lower system level, using a back-and-forth and top-down process. One objective is to reduce the coupling between design elements, which is a measure of system complexity. The equivalent system mass of the alternate systems is compared.

Jones, Harry W.↗
NASA NTRS1979

The effect of fuel sprays on emissions from a gas turbine combustor

A research gas turbine combustor which allows for independent control of drop size, fuel/air ratio, air inlet temperature, pressure, reference velocity, and residence time has been used to study the influence of fuel spray characteristics on primary zone emissions. Local concentrations of oxides of nitrogen, carbon monoxide and unburned hydrocarbons at various locations in the flow, local gas temperature, gas velocity, and the turbulence intensity (measured with laser velocimetry) are obtained. A comprehensive data analysis program to compute the local fuel/air ratio and the sum of the mole fractions of the species present confirms the validity of the emissions data. Increasing drop size is correlated with an increase in unburned hydrocarbons, while increasing residence time is associated with sharp decreases in hydrocarbons and carbon monoxide and an increase in oxides of nitrogen.

Nicholls, J. A.↗
NASA NTRS2013

Parametric Thermal Soak Model for Earth Entry Vehicles

The analysis and design of an Earth Entry Vehicle (EEV) is multidisciplinary in nature, requiring the application many disciplines. An integrated tool called Multi Mission System Analysis for Planetary Entry Descent and Landing or M-SAPE is being developed as part of Entry Vehicle Technology project under In-Space Technology program. Integration of a multidisciplinary problem is a challenging task. Automation of the execution process and data transfer among disciplines can be accomplished to provide significant benefits. Thermal soak analysis and temperature predictions of various interior components of entry vehicle, including the impact foam and payload container are part of the solution that M-SAPE will offer to spacecraft designers. The present paper focuses on the thermal soak analysis of an entry vehicle design based on the Mars Sample Return entry vehicle geometry and discusses a technical approach to develop parametric models for thermal soak analysis that will be integrated into M-SAPE. One of the main objectives is to be able to identify the important parameters and to develop correlation coefficients so that, for a given trajectory, can estimate the peak payload temperature based on relevant trajectory parameters and vehicle geometry. The models are being developed for two primary thermal protection (TPS) materials: 1) carbon phenolic that was used for Galileo and Pioneer Venus probes and, 2) Phenolic Impregnated Carbon Ablator (PICA), TPS material for Mars Science Lab mission. Several representative trajectories were selected from a very large trade space to include in the thermal analysis in order to develop an effective parametric thermal soak model. The selected trajectories covered a wide range of heatload and heatflux combinations. Non-linear, fully transient, thermal finite element simulations were performed for the selected trajectories to generate the temperature histories at the interior of the vehicle. Figure 1 shows the finite element model that was used for the simulations. The results indicate that it takes several hours for the thermal energy to soak into the interior of the vehicle and achieve maximum payload temperatures. In addition, a strong correlation between the heatload and peak payload container temperature is observed that will help establishing the parametric thermal soak model.

Agrawal, Parul↗
NASA NTRS1985

Compatibility of grain-stabilized platinum with candidate propellants for resistojets

Resistojets are candidates for space station auxiliary propulsion, and should be characterized by both long life and multipropellant operations, requirements limited by available materials. Grain stabilized platinum is examined for use as a resistojet thruster material. Use of platinum in other applications indicates it can be used at moderately high temperatures for extended periods of time. Past results indicate that grain-stabilized platinum should be sufficiently inert in candidate propellant environments. Therefore, compatibility of platinum-yttria (P/Y2O3) and platinum-zirconia (Pt/ZrO2) with carbon dioxide, methane, hydrogen and ammonia is examined. A series of 1000 hr tests in CO2, H2, and NH3 is conducted at 1400 C and a series of 1000 hr tests in CH4 is conducted at about 500 C. Scanning electron microscopy, Auger electron spectroscopy and depth profiling analysis are then used to determine the effects of propellants on the material surface, to evaluate possible material contamination and to evaluate grain growth. The results indicate that there is carbon deposition on the surface of the Pt/Y2O3 and Pt/ZrO2 in both the CO2 and CH4 environments. In the H2 environment, the Pt/Y2O3 and Pt/ZrO2 specimen surfaces are roughened. After exposure to the NH3 environment, the Pt/Y2O3 and Pt/ZrO2 are roughened and pitted over the entire heated area with some pitted areas along the grain boundaries. SEM photos show grain growth in cross-sectional views of all the Pt/Y2O3 samples and the Pt/ZrO2 samples, except that tested in methane. Mass loss measurements indicate that Pt/Y2O3 and Pt/ZrO2 would last in excess of 200,000 hr in each propellant environment. However, in NH3 both Pt/Y2O3 and Pt/ZrO2 are severely pitted, with voids up to 50 percent into the material. Pt/Y2O3 and Pt/ZrO2 are not recommended for high temperature service in NH3.

Whalen, M. V.↗
NASA NTRS2013

Process Optimization of Bismaleimide (BMI) Resin Infused Carbon Fiber Composite

Engineers today are presented with the opportunity to design and build the next generation of space vehicles out of the lightest, strongest, and most durable materials available. Composites offer excellent structural characteristics and outstanding reliability in many forms that will be utilized in future aerospace applications including the Commercial Crew and Cargo Program and the Orion space capsule. NASA's Composites for Exploration (CoEx) project researches the various methods of manufacturing composite materials of different fiber characteristics while using proven infusion methods of different resin compositions. Development and testing on these different material combinations will provide engineers the opportunity to produce optimal material compounds for multidisciplinary applications. Through the CoEx project, engineers pursue the opportunity to research and develop repair patch procedures for damaged spacecraft. Working in conjunction with Raptor Resins Inc., NASA engineers are utilizing high flow liquid infusion molding practices to manufacture high-temperature composite parts comprised of intermediate modulus 7 (IM7) carbon fiber material. IM7 is a continuous, high-tensile strength composite with outstanding structural qualities such as high shear strength, tensile strength and modulus as well as excellent corrosion, creep, and fatigue resistance. IM7 carbon fiber, combined with existing thermoset and thermoplastic resin systems, can provide improvements in material strength reinforcement and deformation-resistant properties for high-temperature applications. Void analysis of the different layups of the IM7 material discovered the largest total void composition within the [ +45 , 90 , 90 , -45 ] composite panel. Tensile and compressional testing proved the highest mechanical strength was found in the [0 4] layup. This paper further investigates the infusion procedure of a low-cost/high-performance BMI resin into an IM7 carbon fiber material and the optical, chemical, and mechanical analyses performed.

Ehrlich, Joshua W.↗
NASA NTRSDate not supplied

Analysis of MSL/MEDLI Entry Data with Coupled CFD and Material Response

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heatshield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material [1]. PICA is a lightweight carbon fiber/polymeric resin material that offers outstanding performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP) [2]. The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on OpenFOAM (PATO) [4,5,6] using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA [7], is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Thermal Protection Systems↗
NASA NTRSDate not supplied

Analysis of Pyrolysis Products from Ablative Thermal Protection Systems

NASA’s state-of-the-art ablative materials are composed of a three-dimensional network of carbon fibers impregnated with polymers that dissipate thermal energy through pyrolysis. A fundamental understanding of the decomposition mechanisms and pyrolysis product distributions of various classes of polymers is instrumental in the design of new ablative materials. Furthermore, innovative experiments are essential to the continuous modernization of material response models by providing high-fidelity data. Thus, an apparatus has been designed to measure pyrolysis products from polymers and composite materials by implementing in-situ mass spectrometric techniques. Initial results from experiments performed on siloxane resins and a common phenolic resin will be discussed. Both classes of polymers exhibit heating-rate-dependent decomposition mechanisms. At the onset of heating, phenolic polymers decompose through competitive reactions to form gaseous products and a carbonaceous char. Gas phase products of phenolic resins are typically composed of molecular hydrogen, water, and aromatic hydrocarbons. Pyrolysis products from siloxane polymers include molecular hydrogen, small molecules, and cyclic oligomers from the polymer backbone.

Pyrolysis↗
NASA NTRS1992

Composite materials for the extravehicular mobility unit

The extravehicular mobility unit (EMU), commonly known as the astronaut space suit assembly (SSA) and primary life support system (PLSS), has evolved through the years to incorporate new and innovative materials in order to meet the demands of the space environment. The space shuttle program which is seeing an increasing level of extravehicular activity (EVA), also called space walks, along with interest in an EMU for Lunar-Mars missions means even more demanding conditions are being placed on the suit and PLSS. The project for this NASA-ASEE Summer Program was to investigate new materials for these applications. The focus was to emphasize the use of composite materials for every component of the EMU to enhance the properties while reducing the total weight of the EMU. To accomplish this, development of new materials called fullerene reinforced materials (FRM's) was initiated. Fullerenes are carbon molecules which when added to a material significantly reduce the weight of that material. The Faculty Fellow worked directly on the development of the fullerene reinforced materials. A chamber for fullerene production was designed and assembled and first generation samples were processed. He also supervised with the JSC Colleague, a study of composite materials for the EMU conducted by the student participant in the NASA-ASEE Program, Hector Tello a Rice University graduate student, and by a NASA Aerospace Technologist (Materials Engineer) Evelyne Orndoff, in the Systems Engineering Analysis Office (EC7), also a Rice University graduate student. Hector Tello conducted a study on beryllium and Be alloys and initiated a study of carbon and glass reinforced composites for space applications. Evelyne Orndoff compiled an inventory of the materials on the SSA. Ms. Orndoff also reviewed SSA material requirements and cited aspects of the SSA design where composite materials might be further considered. Hector Tello spent part of his time investigating the solar radiation sensitivity of anodic coatings. This project was directed toward the effects of ultra-violet radiation on high emissivity anodic coatings. The work of both Evelyne Orndoff and Hector Tello is of interest to the Engineering Directorate at NASA/JSC and is also directed toward their research as Rice University graduate students.

Barrera, Enrique V.↗
NASA NTRSDate not supplied

Assessing Potential Geophysical and Environmental Impacts from Frequent Rocket Launch Missions at Kennedy Space Center

Kennedy Space Center (KSC) in Florida has been utilized for space missions over many years with a gradually increasing number of rocket launches. There have been multiple studies where air-coupled acoustic waves and infrasound originating from launched rockets were used for operational purposes, such as locating booster trajectories as a function of changing atmospheric conditions. However, no study has utilized the acoustoelastic waves as a signal source for subsurface seismic investigations. We conducted a dispersion analysis using the seismic energy recorded from the Artemis I rocket launch at KSC in November 2022, and from these results we generated depth-sensitivity kernels at different wave frequencies. The kernels were compared with sedimentary core data to verify boundaries of carbonate layers above the Floridan Aquifer System. Accumulative information of bedrock-sediment boundary across the sedimentary platform could especially provide geo-structural evidence that manifests the configuration of coastal features. Continuous dispersion analysis of seismic recordings from consecutive rocket launches also has potential to identify non-stationary environmental effects, such as reorientation of sedimentary structures and fluctuation of the saltwater/groundwater lens from gravitational tides, which may affect erosional susceptibility of coastal features.

Han Byul Woo↗
NASA NTRSDate not supplied

Assessing Potential Geophysical and Environmental Impacts from Frequent Rocket Launch Missions at Kennedy Space Center

Kennedy Space Center (KSC) in Florida has been utilized for space missions over many years with a gradually increasing number of rocket launches. There have been multiple studies where air-coupled acoustic waves and infrasound originating from launched rockets were used for operational purposes, such as locating booster trajectories as a function of changing atmospheric conditions. However, no study has utilized the acoustoelastic waves as a signal source for subsurface seismic investigations. We conducted a dispersion analysis using the seismic energy recorded from the Artemis I rocket launch at KSC in November 2022, and from these results we generated depth-sensitivity kernels at different wave frequencies. The kernels were compared with sedimentary core data to verify boundaries of carbonate layers above the Floridan Aquifer System. Accumulative information of bedrock-sediment boundary across the sedimentary platform could especially provide geo-structural evidence that manifests the configuration of coastal features. Continuous dispersion analysis of seismic recordings from consecutive rocket launches also has potential to identify non-stationary environmental effects, such as reorientation of sedimentary structures and fluctuation of the saltwater/groundwater lens from gravitational tides, which may affect erosional susceptibility of coastal features.

Rocket Launch Seismicity↗
NASA NTRS1976

A versatile system for biological and soil chemical tests on a planetary landing craft. I - Scientific objectives

We describe an approach for the remote detection and characterization of life in planetary soil samples. A mass spectrometer is used as the central sensor to monitor changes in the gas phase in eleven test cells filled with soil. Many biological assays, ranging from general 'in situ' assays to specific metabolic processes (such as photosynthesis, respiration, denitrification, etc.) can be performed by appropriate additions to the test cell via attached preloaded injector capsules. The system is also compatible with a number of chemical assays such as the analysis of atmospheric composition (both chemical and isotopic), the status of soil water, and the determination of compounds of carbon, nitrogen and sulfur in the soil.

Radmer, R. J.↗
NASA NTRS1978

The rocket-ultraviolet spectrum and models of the planetary nebula NGC 7662

Ultraviolet spectral analysis of NGC 7662 has revealed a Balmer line distribution indicating a C/O ratio of unity. This abundance of carbon is characteristic of mixing between the central star and the outer envelope of the planetary nebula. A continuum spectrum is observed from the star and the nebula, radiating its energy via the two photon process through neutral hydrogen. Spectral lines were fitted to apply to the predictions of three models of the nebular structure. UV observations were compared with visible, IR, and radio observations.

Bohlin, R. C.↗
NASA NTRS1982

Integral throat entrance development, qualification and production for the Antares 3 nozzle

Although design analyses of a G-90 graphite integral throat entrance for the Antares 3 solid rocket motor nozzle indicated acceptable margins of safety, the nozzle throat insert suffered a thermostructural failure during the first development firing. Subsequent re-analysis using properties measured on material from the same billet as the nozzle throat insert showed negative margins. Carbon-carbon was investigated and found to result in large positive margins of safety. The G-90 graphite was replaced by SAI fast processed 4-D material which uses Hercules HM 10000 fiber as the reinforcement. Its construction allows powder filling of the interstices after preform fabrication which accelerates the densification process. Allied 15V coal tar pitch is then used to complete densification. The properties were extensively characterized on this material and six nozzles were subjected to demonstration, development and qualification firings.

Clayton, F. I.↗
NASA NTRS1985

Results of apparent atomic oxygen reactions with spacecraft materials during shuttle flight STS-41G

The effect of atomic oxygen interaction experienced by polymeric-based spacecraft materials is described. An experimental package (ACOMEX) flown on shuttle mission STS-41G carried out the investigation of advanced composite specimens such as carbon-epoxy and Kevlar-epoxy both with and without protective coatings added to thermal protective paints and films. Information on the exposure environment of the specimens was provided by a carbon coated atomic oxygen fluence monitor together with a photographic record. Mass loss measurements and photomicrographs made possible the analysis of the effect of interaction. After a total of about 38 hours of equivalent normal exposure at 225 km altitude the results showed that unprotected exposed surfaces exhibited severe erosion and mass loss with the possibility of seriously degrading structural and thermal performance. However, the specimens with a thin fluorocarbon overcoat showed promise of providing a protective barrier to the attack without altering the base properties of the material.

Zimcik, D. G.↗
NASA NTRS1990

PW Vul: A classical nova with nearly solar abundances

Ultraviolet and optical spectrophotometric data are combined in order to determine the physical parameters in the expanding shell of Nova PW Vul 1984. Ultraviolet data obtained with the International Ultraviolet Explorer (IUE) satellite from August 2, 1984 (a few days after discovery) until it became too faint to study with the satellite is presented. The last IUE exposure was obtained in June 1988 but it was continually followed with ground based optical telescopes. A plot showing the variation of electron density and temperature as a function of time is presented. Analysis of the emission line intensities show that the abundances of this very slow nova are solar for helium, carbon, and oxygen while nitrogen is 50 times solar. The CLOUDY code of Ferland is used to model the emission line intensities and find good agreement with the observations. Plots representative of IUE and optical spectra are displayed.

Saizar, P.↗
NASA NTRS1993

Modeling Thermodynamics Of Charring Of A Polymer

Improved method of predicting and of nondestructively analyzing pyrolytic effects in, and thermomechanical properties of, polymers combines theories and techniques from several engineering and scientific disciplines. Evolved in effort to understand charring and erosion of carbon phenolic ablative material in nozzle of rocket engine. Also applicable to other polymers and particularly to nondestructive engineering analysis of specimens heated, charred, or burned.

Funaro, Gregory V.↗
NASA NTRS1991

The use of ultrasonic property measurements as the basis for finite element analysis of composite materials

In this work, the use of ultrasonic property measurements as the basis for finite element analysis of full scale composite components is presented. The approach utilizes multiple velocity measurements at oblique angles of incidence and quantitative analysis of radiographic images for the local determination of each of the nine orthotropic moduli in a woven carbon-carbon composite. These values were then used as input into a finite element code (NASTRAN) to analyze the response of the material to load: here, diametric compression. The predicted response was then compared with strain gage results at several locations to validate the approach.

Madaras, E. I.↗