Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “bolts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Mechanical Design and Configuration of Penetrations for the Europa Clipper Avionics Vault Structure

The main purpose of the Avionics Vault is to shield radiation sensitive electronics for the Europa Clipper Spacecraft. The vault is a box structure made out of aluminum panels. The panels are roughly 10 mm thick in order to shield the electronics from the orbital total ionizing radiation around Jupiter. The vault requires an electromagnetic interference (EMI) shielding effectiveness (SE) of at least 70 dB in order to mitigate EMI with the spacecraft radar receiver. Overall, the vault accommodates four main types of penetrations: receptacle connectors, pass-through cables, fluid lines, and vent holes. More than 150 cables penetrate the vault panels to connect to electronic boxes inside. Fluid pipes enter and exit the vault to transfer heat to the rest of the spacecraft. Vent holes provide a path for air to escape from the vault during launch. Several novel penetrations designs were created to meet EMI and radiation shielding requirements. Receptacle connectors interface to the vault panels using 1.3 mm thick Ta10W plates. Pass-through cables penetrate the vault using aluminum clamshells after being wrapped with Teflon cushion tape, Kapton tape, and copper tape. Vent hole penetrations consist of a copper mesh for EMI shielding and an aluminum radiation shield bracket to direct air out of the vault during launch. Fluid lines terminate at the vault wall using mechanical fittings that resemble a nut and bolt interface. In addition, most mechanical seams and penetrations utilize EMI gaskets to ensure proper EMI shielding. To reduce risk and confirm that the vault penetration designs were appropriate for EMI shielding, an EMI chamber at the Jet Propulsion Laboratory (JPL) was used to test a mock-up vault panel with multiple variations of all four main types of vault penetrations. This EMI SE test also incorporated different methods for bundling pass-through cables, and a comparison of flange mounted connectors versus jam nut connectors. A low noise preamplifier and a Rohde & Schwarz spectrum analyzer measured E-field levels transmitting through the mock-up vault panel. The results showed a shielding effectiveness of 77 dB for the mock-up vault panel, which exceeds the 70 dB target for Europa Clipper. Both the flange mounted connectors and jam nut connectors exhibited similar EMI SE results at the measured frequencies, and all variations of vault penetrations showed favorable EMI SE levels. Since the flight panels will be much larger and include many more penetrations, there will be testing of the flight vault to confirm its EMI SE is compliant with environmental requirements.

Giersch, Louis↗
NASA NTRSDate not supplied

Towards an Automated Unstructured Grid Adaptation Workflow with VULCAN

Early work is presented for an unstructured grid adaptation workflow with VULCAN and refine. Anisotropic simplex grids are iteratively adapted to match a Riemannian metric tensor field describing desired mesh spacing. The Riemannian metric tensor field is obtained from Hessians of CFD solution output scalar sensor fields; both Mach number and static temperature sensor fields are explored. In addition, we describe a Newton-method-based solver recently implemented in VULCAN utilizing Jacobian-Free-Newton-Krylov that can be used to increase flow solver automation on early grids in the adadptation process. Hypersonic flow solutions are presented on a high Reynolds number flat plate and wall heat flux is compared against a highly resolved structured solution. Additionally, complex shock boundary-layer interaction is explored in a high Mach number compression corner and complex 3D flow phenomena are evaluated on the Boundary Layer Transition (BOLT) vehicle.

Matthew O'Connell↗
NASA NTRS2021

Pedestal Hazard Abatement and Soil Removal Construction Completion Report for Launch Complex 34, Solid Waste Management Unit CC054, Cape Canaveral Space Force Station, Florida

This Construction Completion Report summarizes the activities associated with implementation of an interim measure (IM) for hazard abatement of the Launch Pedestal and soil removal at Launch Complex 34 (LC34), Cape Canaveral Space Force Station, Florida. The purpose of the hazard abatement IM was to mitigate any continuing source of contamination associated with residual paint on the Launch Pedestal that contained polychlorinated biphenyls (PCBs). Sampling determined that residual PCB concerns were limited to the steel elements on the top-side of the Pedestal, which included the torus ring, feed pipe, down pipes, pipe straps and shields, remaining steel cover plates and bolts, and railing support steel. The IM also mitigated the potential spread of contamination to surrounding areas by removing fallen metal fragments from the concrete launch pad, as well as soil from trenches on the launch pad where PCB-containing paint chips may have accumulated prior to or during Pedestal hazard abatement activities.

Complex 34↗
NASA NTRSDate not supplied

Mesh Deformation Boundary Conditions for Three-Dimensional Ablation Solvers

A method for determining boundary node displacements for three-dimensional ablation solvers is developed. The approach is applicable to a wide range of mesh motion algorithms used to determine internal node displacements. The method leverages radial basis functions to analytically define the geometry to which the boundary nodes should be constrained. Constrained optimization, elasticity, and spring analogy solvers are utilized to redistribute the nodes on the evolved geometry surface while maintaining mesh quality. The method is implemented in the CHarring Ablator Response (CHAR) code, and a realistic demonstration case is presented on the Boundary Layer Transition (BOLT) flight experiment configuration. The method is shown to be robust for highly-curved geometries with large domain deformations.

Adam J Amar↗
NASA NTRS2022

Vitrolube NPI-1220 Solid Lubricant Performance After Ultraviolet and Salt Fog Test Exposures

Vitrolube NPI-1220 is a ceramic-bonded solid lubricant produced by National Process Industries, Inc. (NPI) that uses molybdenum disulfide (MoS2) and graphite as lubricating pigments. It is applied to many space flight components, including nickel-alloy and stainless-steel components. Various applications, such as the powered nut and bolt assemblies in the international space station (ISS) (Illi, 1999), the Space Launch System (SLS) sliding bellows, and the SLS ball strut tie-rod assembly (BSTRA) use Vitrolube. No engineering data exists regarding possible Vitrolube degradation after extended exposure to coastal environments encountered by flight hardware on test stands or launch pads. Such environments include ultraviolet (UV) ray, high humidity, and salt exposures. In this study, nickel-alloy disks coated with Vitrolube by NPI, are exposed to controlled UV ray and ‘salt fog’ environments in facilities at Marshall Space Flight Center (MSFC). The exposed disks are run in tribological pin-on-disk tests to quantify any difference in coating lubricity and/or wear compared to coated disks that were not exposed to those environments.

Tribology↗
NASA NTRS2022

How NASA decided Webb was ready: Inside the risk assessment

Every do-it-yourselfer knows how hard it can be to declare a project complete. Will another turn of the bolt or brushstroke make things better or worse? That was roughly the choice NASA faced a year before the Dec. 25 launch of the James Webb Space Telescope. Would more testing close more technical risks in the nearly $10 billion project or create new ones? In the end, NASA decided against more testing. NASA’s Jesse Leitner and Tupper Hyde describe the assessment they performed.

JWST↗
NASA NTRSDate not supplied

Recent Langley Aerothermodynamic Laboratory Testing (2019-2022)

In support of flight programs, multiple wind tunnel entries were conducted on reentry vehicle configurations to investigate blunt body aeroheating environments. Blunt body block thermal protection system (TPS) roughness, the Low-Earth Orbit Flight Test of an Inflatable Decelerator aeroshell scalloping, and a woven TPS all were tested to determine the effects of those parameters on increased surface heating to the vehicle. Commercial Crew Program studies also utilized the speed and ease of testing in the LAL to analyze parametric databases of low-earth reentry configurations, like the Boeing CST-100, and vehicles designed to travel to the moon or Mars, such as the SpaceX Starship. LAL wind tunnel investigations also supported several DoD and AFRL flight projects, such as HIFiRE 6 and BOLT. External customers leveraged the LAL testing capability to advance their research programs, including UPSTAR, RocketLab, and Lawrence Livermore National Laboratory. Academia groups benefitted from the inexpensive cost to test in the tunnels for many university collaborations, such as studies conducted in partnership with the University of Maryland on a flat plate, using a pressure rake and investigating fluid structure interactions. Multiple studies in collaboration with Purdue considered boundary layer transition on various cone configurations. Another study was conducted using a cone with shaped roughness elements borrowed from the Arnold Engineering Development Complex. Internal testing included studies using a phosphor thermography system that can measure higher temperatures than the current LAL phosphor capability and a characterization study of the noise in the wind tunnel flow. The breadth of testing across research and commercial paradigms, both internal and external to NASA, different configurations, a variety of test techniques and aerodynamic and aerothermal environments will be discussed in this overview presentation of the recent work conducted in the LAL.

wind tunnel test↗
NASA NTRS2023

MMIC-I: A Robotic Platform for Assembly Integration and Internal Locomotion through Mechanical Meta-Material Structures

In-space assembly is crucial to creating large-scale space structures and enabling long term space missions. Natural limitations in the size of transportation vehicles and ISRU production facilities necessitate an additive strategy with the size of the typical structural unit being essentially fixed and inversely proportional to the final assembly size. In prior robotic and space assembly examples, reversible mechanical integration of structural modules is typically achieved with actuated alignment and fastening mechanisms onboard every structural module. Additive assembly or manufacturing planning approaches often feature a “build front” that receives new materials or parts and progresses gradually across the target geometry. The system we describe here places much of the alignment and fastener actuation systems onboard a mobile robot that can operate at a build front while companion robots (Scaling Omni-directional Lattice Locomoting Explorer, SOLLE) provide part or material transportation. The design and evaluation of this Mobile Meta-Material Interior Co-Integrator (MMIC-I), an inchworm-style locomoting robotic assembler, is described here with an emphasis on ease of assembly and a low number of unique parts for a simple design. It is designed to assist in alignment of cuboctahedron structural unit cells with captive fasteners, defining the build front in operation. Adjacent structural unit cells are locked together with specified axial and rotational actuation of the fasteners. Hardware prototypes show that the robot is able to successfully locomote to any indexed location within a lattice structure and bolt together each set of fasteners on any interface.

Robotics↗
NASA NTRSDate not supplied

Consolidation of A Sodium Heat Pipe and Stirling Engine for Fission Surface Power

The Consolidated Heat Pipe (CHP) is a new design in which a sodium heat pipe is welded directly to the hot end of the Stirling engine to deliver thermal power more efficiently. The new integrated interface aims to reduce the large temperature drop (about 120 °C) that was measured across the bolted clamp joint between the Stirling engine and the heat pipes during the Kilopower Reactor Using Stirling TechnologY (KRUSTY) test from 2018. Initial testing and characterization of the CHP was performed in ambient air at the NASA Glenn Research Center (GRC). In the test, the heat pipe evaporator section was heated with a tube furnace. The thermal power was then transported to the Stirling engine integrated with a linear alternator that produced electrical power. The CHP has been tested at a hot end temperature ranging from 600 °C - 800 °C and a variety of other Stirling engine parameters (cold end temperature, piston amplitude and pressure). The results show that the temperature drop between the Stirling engine and the heat pipe has been reduced to 2°C - 4 °C. An overall temperature drop of 20 °C – 60 °C was also noted within the heat pipe depending on the combination of parameters mentioned above. Overall, it has been shown that the new Consolidated Heat Pipe design significantly improved the thermal interface to the Stirling engine.

Consolidated↗
NASA NTRSDate not supplied

Consolidation of A Sodium Heat Pipe and Stirling Engine for Fission Surface Power

The Consolidated Heat Pipe (CHP) is a new design in which a sodium heat pipe is welded directly to the hot end of the Stirling engine to deliver thermal power more efficiently. The new integrated interface aims to reduce the large temperature drop (about 120 °C) that was measured across the bolted clamp joint between the Stirling engine and the heat pipes during the Kilopower Reactor Using Stirling TechnologY (KRUSTY) test from 20181. Initial testing and characterization of the CHP was performed in ambient air at the NASA Glenn Research Center (GRC). In the test, the heat pipe evaporator section was heated with a tube furnace. The thermal power was then transported to the Stirling engine integrated with a linear alternator that produced electrical power. The CHP has been tested at a hot end temperature ranging from 600 °C - 800 °C and a variety of other Stirling engine parameters (cold end temperature, piston amplitude and pressure). The results show that the temperature drop between the Stirling engine and the heat pipe has been reduced to 2°C - 4 °C. An overall temperature drop of 20 °C – 60 °C was also noted within the heat pipe depending on the combination of parameters mentioned above. Overall, it has been shown that the new Consolidated Heat Pipe design significantly improved the thermal interface to the Stirling engine.

Consolidated↗
NASA NTRSDate not supplied

Transition prediction in hypersonic regime on complex geometries with RANS-based models

In the near future, RANS computations will continue to play a significant role in the design of hypersonic vehicles with complex geometries. Therefore, it is imperative to continue testing, benchmarking, and refining the RANS models. In the present study, we evaluate RANS-like, transport equations-based models for predicting laminar-turbulent transition over a full-scale scale model of the BOLT flight configuration that was tested in the CUBRC LENS-II wind tunnel test facility. Based on the availability of the experimental results, comparisons are made between computations from several pre-existing transition models and Computational Fluid Dynamics (CFD) codes, with an emphasis on using the same computational meshes and flow conditions for all computations. The analysis covers the sensitivity of the transition predictions to the input parameters for five different transition models (four mainstream models designed for low-speed flows and a uniquely high-speed model), grid resolution, and the details of model implementation across three different flow solvers. The results show that the phenomenological models can describe significant aspects of the measured transition front. However, a number of additional improvements are required before these models can offer more reliable estimates of transition in high-speed flows.

CFD↗
NASA NTRSDate not supplied

Expanding the Capability of A Legacy Combustion Flametube to Test High Temperature Engine Materials in Relevant Environments

New materials and component designs are needed to advance gas turbine engine technology and provide the performance and efficiency needs for future applications. In order to advance these materials, testing in combustion environments is a critical step prior to engine testing. In this work, we detail the design and the fabrication of a materials test sector in a flametube combustor facility. The facility simulates a combustion environment similar to that experienced by components in gas turbine engines. The flow regime is characterized by a combination of high-temperature, high-velocity, high-heat flux, and high-velocity that components experience in gas turbine engines. Exposure of components in this facility allows for the study of combined environmental effects and the impact on both coating and substrate durability. The test facility may operate across a wide range of pressures from 275-400 psig (1,896-2,758 kPa) and an air flow rate of 5 lb/s (2.27 kg/s). While combustion gas temperature is expected in excess of 3,000°F (1,649°C), 900°F (482°C) cooling air may be supplied to the backside of components or test articles. The flametube combustor was previously used to evaluate fuel injectors and combustion products, and the new test configuration will also allow for materials exposure to complex, engine-like conditions. The interior of the Test Section was additively manufactured from GRCop-84 and cryogenically fit and brazed to a stainless steel 304 housing. The use of a copper liner minimizes welds and with active cooling, is expected to provide better durability over traditional hardware using stainless steel or Inconel with a ceramic liner. The Test Section has two opposing removable windows approximately 230 mm x 80 mm that can accommodate articles up to 85 mm tall. This modular design allows for custom platforms to hold coupons, panels, or airfoil shapes to be tested with minimal re-engineering or fabrication. The bolted joint and sealing remains consistent, so any new testing only needs to work within the existing design footprint. This paper will provide an overview of the facility capabilities, design considerations, as well as thermal and structural analysis of the hardware. Future testing of ceramic matrix composite (CMC) airfoils and advanced environmental barrier coatings (EBCs) will also be discussed.

Combustion↗
NASA NTRSDate not supplied

Transition Prediction in Hypersonic Regime on Complex Geometries With Rans-Based Models

In the near future, RANS computations will continue to play a significant role in the design of hypersonic vehicles with complex geometries. Therefore, it is imperative to continue testing, benchmarking, and refining the RANS models. In the present study, we evaluate RANS-like, transport equations-based models for predicting laminar-turbulent transition over a full-scale scale model of the BOLT flight configuration that was tested in the CUBRC LENS-II wind tunnel test facility. Based on the availability of the experimental results, comparisons are made between computations from several pre-existing transition models and Computational Fluid Dynamics (CFD) codes, with an emphasis on using the same computational meshes and flow conditions for all computations. The analysis covers the sensitivity of the transition predictions to the input parameters for five different transition models (four mainstream models designed for low-speed flows and a uniquely high-speed model), grid resolution, and the details of model implementation across three different flow solvers. The results show that the phenomenological models can describe significant aspects of the measured transition front. However, a number of additional improvements are required before these models can offer more reliable estimates of transition in high-speed flows.

CFD↗
NASA NTRSDate not supplied

Survivability of NASA’s 10k RDRE

Rotating detonation rocket engines (RDRE) have widespread global industry and academic interest. Lessons learned in survivability is critical to furthering this technology. To support RDRE development, NASA hot-fire tested several 10k lbf thrust class thrust chamber assemblies with various propellent combinations including liquid oxygen/ liquid methane, liquid oxygen/ liquid hydrogen, and liquid oxygen/RP-1. The thrust chamber assemblies include injectors, inner bodies, and outer bodies that were additively manufactured (AM) laser powder bed fusion (L-PBF) GRCop-42. This paper will cover hardware damage identified in the 2023 and 2024 RDRE testing campaigns and lessons learned to improve survivability for future RDREs. Particularly notable were the findings concerning the number of detonation waves formed and their effects on the bolted interface and its sealing.

Tessa M. Fedotowsky↗
NASA NTRS2023

Damage Detection of a Pressure Vessel with Smart Sensing and Deep Learning

Structural Health Monitoring plays a crucial role in ensuring the safety and reliability of critical infrastructure, including pressure vessels involved in various applications. This research reports the damage detection of a pressure box employed in space habitat that operates in harsh environment where both structural failure and bolt joint loosening may occur. These failure modes are extremely hard to model based on first principles. We explore proper sensing mechanism and the associated inverse analysis algorithm that can elucidate the health condition of the pressure box. It is identified that piezoelectric impedance based active interrogation can provide necessary information for damage detection in such a system. Concurrently, deep learning technique leveraging spatial convolutional neural network is synthesized to analyze the raw data acquired and identify different types of damage. By training the deep learning model on a dataset of healthy and various damage scenarios, we can achieve high accuracy in identifying the presence of damage and its type. This research provides a data-driven methodology for structural damage detection using deep learning and has the potential to be extended to various systems with different failure modes.

Yang Zhang↗
NASA NTRSDate not supplied

LS-DYNA User-Defined Internal Ballistic Modeling

One of the challenges in modeling deflagration of solid propellants with LS-DYNA is its limited capability, which is mostly applicable to airbag systems that use gaseous nitrogen generated by burning sodium azide. To overcome this limitation and enable the modeling of custom propellant grains with specific geometries, perforations, surface inhibitors, impetus, burn rates, and co-volumes, a user-defined burn model must be defined. In this study, a custom internal ballistic analysis code is integrated into LS-DYNA to simulate kinematic systems driven by pyro-mechanical devices such as pyro pushers, cutters, thrusters, separations bolts, ejection seat catapults, etc. Step-by-step guidance is provided on implementing a user-defined loading subroutine and the requirements for compiling a custom LS-DYNA executable along with a simple pyro thruster example.

pyrotechnics↗
NASA NTRS2024

On the Effectiveness of Using Woven Outer Plies to Suppress Hole Drilling Face Sheet Damage in Honeycomb Sandwich Structure

A payload adaptor fitting (PAF) structure has been manufactured at NASA’s Marshall Space Flight Center (MSFC). The PAF structure is essentially a large cone made of carbon/epoxy sandwich structure. The PAF structure contains numerous (about 1000) holes at the top and bottom to secure the carbon/epoxy structure in aluminum rings with bolts. In an effort to obtain higher quality holes, both sides of the PAF structure are covered with an additional, non-structural, ply of woven carbon/epoxy placed at ±45⁰ to the vertical direction. This study evaluated the quality of the holes on sandwich structure both with and without the outer woven carbon/epoxy plies via open hole compression (OHC) strength testing. Results showed a 14% increase in strength of the cloth covered sandwich structure, which did not surpass the 18% added weight due to the outer woven plies.

sacrificial plies↗
NASA NTRSDate not supplied

Dynamics and Clearance Analysis of NASA's Space Launch System Block-1 and Block 1B Solid Rocket Booster Separation Event

NASA’s Space Launch System (SLS) solid rocket booster separation event is an essential area of study requiring high fidelity modelling to capture the complexity of an intra-atmospheric stage separation event. The setup and analysis for this event leveraged the NASA-developed CLVTOPS multi-body dynamics toolchain to model aerodynamics at the separation event, booster thrust tailoff, and Core Stage engine throttling in addition to the separation system itself (booster separation motors (BSMs), pyrotechnic bolts and struts). The approach documented here will give a brief background on the CLVTOPS toolchain, how key input models are integrated and verified, and how results are quantified using an ordered-statistics approach. Specific areas discussed herein address the performance-to-orbit realized by adjusting the delay time between the separation cue and the actual separation event, and how the orientation of the aft BSMs was tuned to address small clearances between the aft diagonal attach struts and the Core Stage. Post-flight results from the inaugural Artemis I flight are also shown, and validation is performed between predicted vs. actual separation dynamics and clearances. Challenging night launch conditions necessitated comparisons that were more qualitative in nature, but still showed very good agreement to pre-flight predictions.

Carole J Addona↗