Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “backing layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Back-Surface Passivation of CdTe Solar Cells Using Solution-Processed Oxidized Aluminum

Although back-surface passivation plays an important role in high-efficiency photovoltaics, it has not yet been definitively demonstrated for CdTe. Here, we present a solution-based process, which achieves passivation and improved electrical performance when very small amounts of oxidized Al 3+ species are deposited at the back surface of CdTe devices. The open circuit voltage (V oc ) is increased and the fill factor (FF) and photoconversion efficiency (PCE) are optimized when the total amount added corresponds to ~1 monolayer, suggesting that the passivation is surface specific. Addition of further Al 3+ species, present in a sparse alumina-like layer, causes the FF and PCE to drop as the interface layer becomes blocking to current flow. The optimized deposit increases the average baseline PCE for both Cu-free devices and devices where Cu is present as a dopant. The greatest improvement is found when the Al 3+ species are deposited prior to the CdCl 2 activation step and Cu is employed. In this case, the best-cell efficiency was improved from 12.6 to 14.4%. Furthermore, time-resolved photoluminescence measurements at the back surface and quantum efficiency measurements performed at the maximum power point indicate that the performance enhancement is due to a reduction in the interface recombination current at the back surface.

14 SOLAR ENERGY↗

Recombination phenomena in high efficiency silicon solar cells

The dominant recombination phenomena which limit the highest efficiency attainable in silicon solar cells under terrestrial sunlight are reviewed. The ultimate achievable efficiency is limited by the two intrinsic recombination mechanisms, the interband Auger recombination and interband Radiative recombination, both of which occur in the entire cell body but principally in the base layer. It is suggested that an optimum (26%) cell design is one with lowly doped 50 to 100 micron thick base, a perfect BSF, and zero extrinsic recombination such as the thermal mechanism at recombination centers the Shockley-Read-Hall process (SRH) in the bulk, on the surface and at the interfaces. The importance of recombination at the interfaces of a high-efficiency cell is demonstrated by the ohmic contact on the back surface whose interface recombination velocity is infinite. The importance of surface and interface recombination is demonstrated by representing the auger and radiative recombination losses by effective recombination velocities. It is demonstrated that the three highest efficiency cells may all be limited by the SRH recombination losses at recombination centers in the base layer.

Sah, C. T.↗

Effect of oxide layer growth conditions on radiation detection performance of Ni/SiO 2 /epi-4H-SiC MOS capacitors

We report high resolution radiation detection has been demonstrated using Ni/SiO2/n-4H-SiC metal-oxidesemiconductor vertical capacitors fabricated using highly crystalline 4H-SiC epilayers. The oxide layers have been grown thermally using two different approaches: i) in-air, and ii) oxygen-ambience oxidation. The devices fabricated using the former method exhibited dark currents one order of magnitude higher than that in the latter. The observed difference has been attributed to the back-contact series resistance and capacitance. Regardless of the difference in the device parameters, detectors prepared using both of the methods exhibited very high energy resolutions of ≤ 0.5% for 5486 keV alpha particles emitted by an 241Am radioisotope. Capacitance mode deep level transient spectroscopic (DLTS) studies revealed similar type of electrically active defects along with Z1/2 and EH5 deep level defects in both the types of devices. The DLTS scans also revealed positive polarity peaks in these devices which indicate emission from minority carrier trap centers. The activation energy corresponding to the peak was found to be ~1.2 eV which has been assigned to HK3 defects responsible for hole trapping in 4H-SiC. The possibility of appearance of the positive peak due to non-negligible impedance of the back-contact has been ruled out based on the observation that the centroid of the observed peak did not change with detectors having different device parameters.

36 MATERIALS SCIENCE↗

Power assist EVA glove development

Structural modeling of the EVA glove indicates that flexibility in the metacarpophalangeal (MCP) joint can be improved by selectively lowering the elasticity of the glove fabric. Two strategies are used to accomplish this. One method uses coil springs on the back of the glove to carry the tension in the glove skin due to pressurization. These springs carry the loads normally borne by the glove fabric, but are more easily deformed. An active system was also designed for the same purpose and uses gas filled bladders attached to the back of the EVA glove that change the dimensions of the back of the glove and allow the glove to bend at the MCP joint, thus providing greater flexibility at this joint. A threshold control scheme was devised to control the action of the joint actuators. Input to the controller was provided by thin resistive pressure sensors placed between the hand and the pressurized glove. The pressure sensors consist of a layer of polyester film that has a thin layer of ink screened on the surface. The resistivity of the ink is pressure dependent, so an extremely thin pressure sensor can be fabricated by covering the ink patch with another layer of polyester film and measuring the changing resistance of the ink with a bridge circuit. In order to sense the force between the hand and the glove at the MCP joint, a sensor was placed on the palmar face of the middle finger. The resultant signal was used by the controller to decide whether to fill or exhaust the bladder actuators on the back of the glove. The information from the sensor can also be used to evaluate the effectiveness of a given control scheme or glove design since the magnitude of the measured pressures gives some idea of the torque required to bend a glove finger at the MCP joint. Tests of this actuator, sensor, and control system were conducted in an 57.2 kPa glove box by performing a series of 90 degree finger bends with a glove without an MCP joint assembly, a glove with the coil spring assembly, and with the four fingered actuated glove. The tests of these three glove designs confirm the validity of the model.

Main, John A.↗

Characterization of few-layered graphene grown by carbon implantation

Graphene is considered to be a very promising material for applications in nanotechnology. The properties of graphene are strongly dependent on defects that occur during growth and processing. These defects can be either detrimental or beneficial to device performance depending on defect type, location and device application. Here we present experimental results on formation of few-layered graphene by carbon ion implantation into nickel films and characteristics of graphene devices formed by graphene transfer and lithographic patterning. Micro-Raman spectroscopy was used to determine the number of graphene layers formed and identify defects arising from the device processing. The graphene films were cleaned by annealing in vacuum. Transport properties of cleaned graphene films were investigated by fabrication of back-gated field-effect transistors, which exhibited high hole and electron mobility of 1935 and 1905 cm2/Vs, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

p{sup +}-doping analysis of laser fired contacts for silicon solar cells by Kelvin probe force microscopy

Local rear contacts for silicon passivated emitter and rear contact solar cells can be established by point-wise treating an Al layer with laser radiation and thereby establishing an electrical contact between Al and Si bulk through the dielectric passivation layer. In this laser fired contacts (LFC) process, Al can establish a few μm thick p{sup +}-doped Si region below the metal/Si interface and forms in this way a local back surface field which reduces carrier recombination at the contacts. In this work, the applicability of Kelvin probe force microscopy (KPFM) to the investigation of LFCs considering the p{sup +}-doping distribution is demonstrated. The method is based on atomic force microscopy and enables the evaluation of the lateral 2D Fermi-level characteristics at sub-micrometer resolution. The distribution of the electrical potential and therefore the local hole concentration in and around the laser fired region can be measured. KPFM is performed on mechanically polished cross-sections of p{sup +}-doped Si regions formed by the LFC process. The sample preparation is of great importance because the KPFM signal is very surface sensitive. Furthermore, the measurement is responsive to sample illumination and the height of the applied voltage between tip and sample. With other measurement techniques like micro-Raman spectroscopy, electrochemical capacitance-voltage, and energy dispersive X-ray analysis, a high local hole concentration in the range of 10{sup 19 }cm{sup −3} is demonstrated in the laser fired region. This provides, in combination with the high spatial resolution of the doping distribution measured by KPFM, a promising approach for microscopic understanding and further optimization of the LFC process.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The 'last mile' of data handling: Fermilab's IFDH tools

IFDH (Intensity Frontier Data Handling), is a suite of tools for data movement tasks for Fermilab experiments and is an important part of the FIFE[2] (Fabric for Intensity Frontier [1] Experiments) initiative described at this conference. IFDH encompasses moving input data from caches or storage elements to compute nodes (the 'last mile' of data movement) and moving output data potentially to those caches as part of the journey back to the user. IFDH also involves throttling and locking to ensure that large numbers of jobs do not cause data movement bottlenecks. IFDH is realized as an easy to use layer that users call in their job scripts (e.g. 'ifdh cp'), hiding the low level data movement tools. One advantage of this layer is that the underlying low level tools can be selected or changed without the need for the user to alter their scripts. Logging and performance monitoring can also be added easily. This system will be presented in detail as well as its impact on the ease of data handling at Fermilab experiments.

Lyon, Adam L.↗

Laser processing for thin film chalcogenide photovoltaics: a review and prospectus

We review prior and on-going works in using laser annealing (LA) techniques in the development of chalcogenide-based [CdTe and Cu(In,Ga)(S,Se) 2 ] solar cells. LA can achieve unique processing regimes as the wavelength and pulse duration can be chosen to selectively heat particular layers of a thin film solar cell or even particular regions within a single layer. Pulsed LA, in particular, can achieve non-steady-state conditions that allow for stoichiometry control by preferential evaporation, which has been utilized in CdTe solar cells to create Ohmic back contacts. Pulsed lasers have also been used with Cu(In,Ga)(S,Se) 2 ] to improve device performance by surface-defect annealing as well as bulk deep-defect annealing. Continuouswave LA shows promise for use as a replacement for furnace annealing as it almost instantaneously supplies heat to the absorbing film without wasting time or energy to bring the much thicker substrate to temperature. Optimizing and utilizing such a technology would allow production lines to increase throughput and thus manufacturing capacity. Lasers have also been used to create potentially low-cost chalcogenide thin films from precursors, which is also reviewed.

14 SOLAR ENERGY↗

A New Discrete Element Sea-Ice Model for Earth System Modeling

Sea ice forms a frozen crust of sea water oating in high-latitude oceans. It is a critical component of the Earth system because its formation helps to drive the global thermohaline circulation, and its seasonal waxing and waning in the high north and Southern Ocean signi cantly affects planetary albedo. Usually 4{6% of Earth's marine surface is covered by sea ice at any one time, which limits the exchange of heat, momentum, and mass between the atmosphere and ocean in the polar realms. Snow accumulates on sea ice and inhibits its vertical growth, increases its albedo, and contributes to pooled water in melt ponds that darken the Arctic ice surface in the spring. Ice extent and volume are subject to strong seasonal, inter-annual and hemispheric variations, and climatic trends, which Earth System Models (ESMs) are challenged to simulate accurately (Stroeve et al., 2012; Stocker et al., 2013). This is because there are strong coupled feedbacks across the atmosphere-ice-ocean boundary layers, including the ice-albedo feedback, whereby a reduced ice cover leads to increased upper ocean heating, further enhancing sea-ice melt and reducing incident solar radiation re ected back into the atmosphere (Perovich et al., 2008). A reduction in perennial Arctic sea-ice during the satellite era has been implicated in mid-latitude weather changes, including over North America (Overland et al., 2015). Meanwhile, most ESMs have been unable to simulate observed inter-annual variability and trends in Antarctic sea-ice extent during the same period (Gagne et al., 2014).

54 ENVIRONMENTAL SCIENCES↗

Determination of lifetimes and recombination currents in p-n junction solar cells, diodes, and transistors

New methods are presented and illustrated that enable the accurate determination of the diffusion length of minority carriers in the narrow regions of a solar cell or a diode. Other methods now available are inaccurate for the desired case in which the width of the region is less than the diffusion length. Once the diffusion length is determined by the new methods, this result can be combined with measured dark I-V characteristics and with small-signal admittance characteristics to enable determination of the recombination currents in each quasi-neutral region of the cell - for example, in the emitter, low-doped base, and high-doped base regions of the BSF (back-surface-field) cell. This approach leads to values for the effective surface recombination velocity of the high-low junction forming the back-surface field of BSF cells or the high-low emitter junction of HLE cells. These methods are also applicable for measuring the minority-carrier lifetime in thin epitaxial layers grown on substrates with opposite conductivity type.

Neugroschel, A.↗

Advanced silicon on insulator technology

Undoped, thin-layer silicon-on-insulator was fabricated using wafer bonding and selective etching techniques employing a molecular beam epitaxy (MBE) grown Si0.7Ge0.3 layer as an etch stop. Defect free, undoped 200-350 nm silicon layers over silicon dioxide are routinely fabricated using this procedure. A new selective silicon-germanium etch was developed that significantly improves the ease of fabrication of the bond and etch back silicon insulator (BESOI) material.

Godbey, D.↗

A parametric study of supersonic laminar flow for swept wings using linear stability analysis

A parametric study to predict the extent of laminar flow on the upper surface of a generic swept-back wing (NACA 64A010 airfoil section) at supersonic speeds was conducted. The results were obtained by using surface pressure predictions from an Euler/Navier-Stokes computational fluid dynamics code coupled with a boundary layer code, which predicts detailed boundary layer profiles, and finally with a linear stability code to determine the extent of laminar flow. The parameters addressed are Reynolds number, angle of attack, and leading-edge wing sweep. The results of this study show that an increase in angle of attack, for specific Reynolds numbers, can actually delay transition. Therefore, higher lift capability, caused by the increased angle of attack, as well as a reduction in viscous drag due to the delay in transition is possible for certain flight conditions.

Cummings, Russell M.↗

PNNL Researchers Collect Permafrost Cores in Alaska

Permafrost is ground that is frozen for two or more years. In the Arctic, discontinuous regions of this saturated admixture of soil and rock store a large fraction of the Earth’s carbon – about 1672 petagrams (1672 trillion kilograms). As temperatures increase in the Northern Hemisphere, a lot of that carbon may be released to the atmosphere, making permafrost an important factor to represent accurately in global climate models. At Pacific Northwest National Laboratory, a group led by James C. Stegen periodically extracts permafrost core samples from a site near Fairbanks, Alaska. Back at the lab in southeastern Washington State, they study the cores for levels of microbial activity, carbon fluxes, hydrologic patterns, and other factors that reveal the dynamics of this consequential layer of soil and rock.

54 ENVIRONMENTAL SCIENCES↗

Regrowth-free single-mode quantum cascade lasers with power consumption below 1 W

We report on single-mode distributed-feedback quantum cascade lasers emitting at 4.8 μm with continuous-wave threshold power consumption as low as 0.76 W at 20 °C and 0.98 W at 50 °C. Following growth of the laser active region and semiconductor cladding layers by a single molecular beam epitaxy process, devices with 4-μm-wide ridges and vertical sidewall gratings were fabricated using plasma etching and standard dielectric and metal deposition processes. In terms of mode stability, output power, and efficiency, we show that lasers with 1-mm cavity length and high-reflectivity back-facet coatings can match the performance of buried heterostructure devices, but with the advantage of requiring only a single epitaxial growth step.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Subsurface Cl-bearing salts as potential contributors to recurring slope lineae (RSL) on Mars

We report laboratory experimental results that support a brine-related hypothesis for the recurring slope lineae (RSL) on Mars in which the subsurface Cl-salts, i.e., hydrous chlorides and oxychlorine salts (HyCOS) are the potential source materials. Our experiments revealed that within the observed RSL temperature window TRSL (250–300 K), the deliquescence of HyCOS could occur in relative humidity ranges (RH≥22%–46%) much lower than those for hydrous (Mg, Fe)-sulfates (RH≥75%–96%). In addition, we demonstrated that the RH values kept by common HyCOS and hydrous sulfates in enclosures have a general trend as RH(sulfates) > RH(perchlorates) > RH(chlorides) (with same type of cation) in wide T range. It means that the required RH range for a Cl-bearing salt to deliquescence can be satisfied by a co-existing salt of different type, e.g., in the subsurface layers of mixed salts on Mars. Furthermore, we found a strong temperature dependence of the deliquescence rates for all tested HyCOS, e.g., a duration of 1–5 sols for all HyCOS at the high end (300 K) of TRSL, and of 20–70 sols for all tested HyCOS (except NaClO4·H2O) at the low end (250 K) of TRSL, which is consistent with the observed seasonal behavior of RSL on Mars. From a mass-balance point of view, the currently observed evidences on Mars do not support a fully-brine-wetted track model, thus we suggest a brine-triggered granular-flow model for the most RSL. Considering the recurrence of RSL in consecutive martian years, our experimental results support the rehydration of remnant HyCOS layers during a martian cold season through H2O vapor-to-salt direct interaction. We found that the evidences of HyCOS rehydration under Mars relevant P-T-RH conditions are detectable in a few minutes by in situ Raman spectroscopy. This rehydration would facilitate the recharge of H2O back into subsurface HyCOS, which could serve as the source material to trigger RSL in a subsequent warm season. The major limiting factor for this rehydration is the H2O supply, i.e., the H2O vapor density carried by current Mars atmospheric circulation and the diffusion rate of H2O vapor into the salt-rich subsurface in a cold season. In a worst-case scenario, these H2O supplies can support a maximum increase of hydration degrees of two for totally dehydrated HyCOS, whereas the full rehydration of subsurface HyCOS layers can be easily reached during a>30° obliquity period that has H2O vapor density 10× to 20× times the value of current obliquity. Overall, our results imply the existence of a large amount of Cl-bearing salts in the subsurface at RSL sites.

Alian Wang↗

A Theory of Exoplanet Transits with Light Scattering

Exoplanet transit spectroscopy enables the characterization of distant worlds, and will yield key results for NASA's James Webb Space Telescope . However, transit spectra models are often simplified, omitting potentially important processes like refraction and multiple scattering. While the former process has seen recent development, the effects of light multiple scattering on exoplanet transit spectra have received little attention. Here, we develop a detailed theory of exoplanet transit spectroscopy that extends to the full refracting and multiple scattering case. We explore the importance of scattering for planet-wide cloud layers, where the relevant parameters are the slant scattering optical depth, the scattering asymmetry parameter, and the angular size of the host star. The latter determines the size of the “target” for a photon that is back-mapped from an observer. We provide results that straightforwardly indicate the potential importance of multiple scattering for transit spectra. When the orbital distance is smaller than 10–20 times the stellar radius, multiple scattering effects for aerosols with asymmetry parameters larger than 0.8–0.9 can become significant. We provide examples of the impacts of cloud/haze multiple scattering on transit spectra of a hot Jupiter-like exoplanet. For cases with a forward and conservatively scattering cloud/haze, differences due to multiple scattering effects can exceed 200 ppm, but shrink to zero at wavelength ranges corresponding to strong gas absorption or when the slant optical depth of the cloud exceeds several tens. We conclude with a discussion of types of aerosols for which multiple scattering in transit spectra may be important.

79 ASTRONOMY AND ASTROPHYSICS↗