Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Twinning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Activation of dislocations in Mg with solute Y

Mg-Y cast alloy shows excellent ductility (elongation to failure > 15%) compared with pure Mg and commercial Mg cast alloys. By monitoring the microstructure evolution during an in situ tensile test of a Mg-2.5 wt%Y alloy, we identify the activation of prismatic slip, which is rare in Mg. Synchrotron X-ray micro-beam Laue diffraction (μ-Laue) and transmission electron microscopy revealed the morphology of prismatic slip bands and individual dislocations. Density functional theory and molecular dynamics calculations indicate that solute Y can significantly reduce the stacking fault energy (SFE) along direction on prismatic plane in Mg lattice and thus facilitate the nucleation of dislocations during deformation. The presence of free dislocations in the Mg lattice can also lead to nucleation of {10–12} twins even under unfavorable geometric conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Disorder-induced time effect in the antiferromagnetic domain state of Fe 1+ y Te

Herein we report on temperature-dependent soft X-ray absorption spectroscopy (XAS) measurements utilizing linearly polarized synchrotron radiation to probe magnetic phase transitions in iron-rich Fe 1+y Te (y ≈ 0.12). X-ray magnetic linear dichroism (XMLD) signals, which sense magnetic ordering processes at surfaces, start to increase monotonically below the Néel temperature T N = 57 K. This increase is due to a progressive bicollinear antiferromagnetic (AFM) alignment of Fe spins of the monoclinic Fe 1+y Te parent phase. This AFM alignment was achieved by a [1 0 0]-oriented biasing field favoring a single-domain state during cooling across T N . Our specific heat and magnetization measurements confirm the bulk character of this AFM phase transition. On longer time scales, however, we observe that the field-biased AFM state is highly unstable even at the lowest temperature of T = 3 K. After switching off the biasing field, the XMLD signal decays exponentially with a time constant τ = 1506 s. The initial XMLD signal is restored only upon repeating a cycle consisting of heating and field-cooling through T N . We explain the time effect by a gradual formation of a multi-domain state with 90° rotated AFM domains, promoted by structural disorder, facilitating the motion of twin-domains. Significant disorder in our Fe 1+y Te sample is evident from our X-ray diffraction and specific heat data. The stability of magnetic phases in Fe-chalcogenides is an important material property, since the Fe(Te 1-x Se x ) phase diagram shows magnetism intimately connected with superconductivity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Self-consistent solution of the Frank–Bilby equation for interfaces containing disconnections

The quantized Frank–Bilby equation can be used to identify interfacial line defect array configurations which relax the misorientation and/or misfit of a coherent crystalline interface. These line defect arrays may be comprised of dislocations and/or disconnections, which are interfacial steps with dislocation character. When an interface contains disconnections, solution of the quantized Frank–Bilby equation is complicated by the fact that the habit plane orientation is not known in advance because it depends on the unknown spacing of the disconnection array. We present a root-finding-based method for addressing this issue, enabling a self-consistent solution for arbitrary defect content. Our method has been implemented in an open-source code which enumerates all possible solutions given a list of candidate line defects. Two cases are presented employing the code: a misoriented FCC twin boundary and an FCC/BCC phase boundary with the Nishiyama-Wasserman orientation relationship. Both cases exhibit more than 10,000 solutions to the Frank–Bilby equation, with several hundred solutions categorized as ‘‘low energy’’ and thus plausible configurations for the actual interface. The resulting set of solutions can be utilized to predict and understand the properties of a given interface.

42 ENGINEERING↗
DOE OSTI2025

Dislocation nano-hydrides in nickel: Nucleation, evolution and effects on dislocation behaviors

Nano-hydrides have been predicted to precipitate at the core of edge dislocations in the Ni-H system, a mechanism that may promote hydrogen embrittlement. However, nano-hydride nucleation, growth, and effects on dislocation behavior have seldom been explored. This work combines molecular dynamics grand canonical Monte Carlo (MD-GCMC) simulations and continuum modeling to uncover a wide range of phenomena linked to dislocation nano-hydrides. Simulations reveal that nano-hydrides can be stabilized at dislocation cores with all character angles, including screw segments, due to the hydrostatic stresses around the cores of the Shockley partials. Nano-hydride nucleation takes place in these regions, and growth is dictated by the character angle θ of the perfect dislocation. The equilibrium stacking fault width d eq varies dynamically to increase the local hydrostatic stress field and facilitate the formation of the nano-hydride, forming a constriction-like feature and leading to three distinct behaviors: d eq decreases for θ > 30°, d eq remains unchanged for θ = 30°, and d eq increases for θ < 30°. Remote hydrostatic and Escaig stresses are also shown to influence the nucleation stage, implying stress concentrations such as those ahead of crack tips may facilitate nano-hydride precipitation. Moreover, we identify a new hydrogen-induced 60° dislocation reaction that emits a Shockley partial on a conjugate plane, with potential implications for twin nucleation. Testable predictions from this study are then used to reinterpret previous results from the literature. In conclusion, these findings provide a comprehensive framework to assess nano-hydride formation and evolution at dislocations in nickel and other face-centered cubic metals, with important implications to hydrogen embrittlement.

Dislocations↗
DOE OSTI2022

Cantor-derived medium-entropy alloys: bridging the gap between traditional metallic and high-entropy alloys

The year 2004 marked the beginning of a new era in the design of metallic materials, as the concept of multiple principal component alloys, commonly known as High-Entropy Alloys (HEAs), was proposed by Cantor and Yeh. The unexpected single-phase microstructure, instead of the expected brittle intermetallic compounds, was attributed to the large entropy of mixing and immediately caught the attention of the scientific community. Today, HEAs are considered important advanced materials and a broad range of alloys using nominally the same design principle have been investigated. Despite that, the CrMnFeCoNi (Cantor) alloy stands out as the most successful HEA due to its outstanding mechanical properties and microstructure. In this scenario, variants of the Cantor alloy, named medium-entropy alloys (MEAs), are gaining significant interest as they display a better industrial potential than both HEAs and traditional alloys. These variants of the Cantor alloy with only three or four main elements result in 15 possible combinations. The microstructure of these alloys is discussed in terms of advanced characterization as well as thermodynamic parameters and computational simulation. Their phase stability is addressed over a wide range of temperatures and strain rates. The mechanical properties, especially the fracture toughness, of the CrFeCoNi and CrCoNi alloys have been reported to be even superior to those of the Cantor alloy and most modern engineering alloys. This is associated with the formation of a continuous sequence of strengthening mechanisms, including hierarchical twin networks, which serve to prolong the strain hardening. The present article reviews and critically assesses, for the first time, recent advances in these Cantor-derived MEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanical behavior and shear band of a powder-metallurgy-fabricated CoCrFeMnNi high-entropy alloy during high strain-rate deformation

High-entropy alloys (HEAs) fabricated by powder metallurgy are considered to exhibit extremely-great potential application values in the field for high-speed impact deformation due to their uniform microstructures and compositions. The mechanical behavior of a powder-metallurgy-fabricated (PM) CoCrFeMnNi HEA was investigated at room temperature with strain rates ranging from 1200 s -1 to 2800 s -1 . It was found that the serration behavior and shear localization of the alloy under dynamic conditions occurred. Results also indicated that the serrated flow took place in the PM CoCrFeMnNi HEA during mechanical deformation at high strain rates (>1000 s -1 ) and became more pronounced as the strain rate increased. Furthermore, it was determined that the yield-strength values of the PM CoCrFeMnNi HEA were sensitive to strain rates, where the values increased from 500 MPa to 700 MPa when the strain rates increased from 1200 s -1 to 2800 s -1 . Shear bands with a width of about 20 μm were generated in the PM CoCrFeMnNi HEA after the shear stress reached a maximum value of 635 MPa, which corresponded to a nominal strain of about 8.71. Nanotwins and ultrafine-equiaxed grains with a diameter of about 150 nm also developed at the core of the shear band during deformation. The results revealed that the strength of the shear band was much higher than that of the matrix grain. Nanotwins in the shear band were composed of a single face-centered-cubic (FCC) structure with the twin plane of ($\bar{1}$1$\bar1$), which could be formed via a rotational dynamic recrystallization (RDR).

36 MATERIALS SCIENCE↗
DOE OSTI2023

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

A novel Cu-added medium-Mn steel with a chemical composition of Fe–0.27C–9.1Mn–1.86Al–3.3Cu (wt.%) was designed and subjected to intercritical annealing (IA) temperature range from 620 °C to 680 °C for 1 h. The ultimate tensile strength (UTS) increases and the yielding strength (YS) decreases with the IA temperature increasing. The YS of 824 MPa, UTS of 1222 MPa, total elongation (TE) of 55%, and product of strength and elongation (PSE) of 67.2 GPa·% are achieved after IA at 660 °C. Transmission electron microscopy confirmed that Cu-rich nanoparticles precipitate in the ferrite. The in-situ high-energy X-ray diffraction (HE-XRD) experiments show that at the beginning of plastic deformation, both austenite and ferrite bear the applied load. The load is mainly undertaken by martensite with effective transformation-induced plasticity (TRIP) effect triggered. The YS of ferrite is significantly higher than that of austenite. The individual contribution of solid solution strengthening, grain refinement strengthening, dislocation strengthening, and precipitation strengthening in ferrite and austenite is analyzed. The discrepancy between the YS of ferrite and austenite is mainly attributed to the precipitation strengthening due to the Cu-rich nanoparticles precipitation. The moderate mechanical stability and the collaboration of TRIP and twinning-induced plasticity (TWIP) effects of austenite contributed to the enhanced strain hardening capability and resulted in large ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigation of the structure and chemical nature of Pd fission product agglomerations in irradiated TRISO particle SiC

Tristructural-isotropic (TRISO)-coated fuel particles are used in high-temperature gas-cooled nuclear reactors. Although the polycrystalline 3C-SiC layer acts as the main barrier to fission product release, post-irradiation examinations have shown that certain metallic fission products are found outside of the TRISO coated particle, with no observable micro-cracks or other mechanical failure feature. In this study, an atomic resolution transmission electron microscopy investigation of a SiC layer of a neutron irradiated (19.38% fissions per initial metal atom average burnup; 1072°C time-averaged temperature) TRISO-coated particle from the first advanced gas reactor experiment at Idaho National Laboratory containing mainly Pd and U was conducted. The fission product Pd was found to be present at dislocation cores associated with twins, stacking faults, and their intersections. The Pd present at the dislocation cores were bonded to Si, suggesting that the diffusion of Pd along the SiC dislocation cores involves the formation of Pd-Si bonds. Evidence of single atom grain boundary migration was also found. Fission product agglomerations at grain boundaries most likely consist of a random solid solution containing Si-FP, Si-C, and C-C type bonding arrangements. No difference in the Si- or C-bonding environment is found for the unoccupied grain boundary adjacent to a fission product agglomeration compared to the bulk SiC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Evaluation of the anisotropic grain boundaries and surfaces of α -U via molecular dynamics

Alloys based on uranium-zirconium are gaining renewed interest as fuels for the Versatile Test Reactor and a number of microreactor designs. Implementing metallic fuel in reactors creates the need for robust descriptive and predictive fuel performance modeling. Here, the current state of metallic fuel performance modeling relies on empirical equations derived from historical experiments, which may be unreliable when applied outside of their temperature, power, and composition phase space. One area where such data is lacking is the irradiation behavior of alpha -U, specifically tearing and porosity formation at the early stages of irradiation. While grain boundaries likely play a key role in this fuel behavior, relatively little is known about grain boundaries in alpha-U. Thus, we evaluate the grain boundary, surface energy, and work of adhesion of alpha -U utilizing molecular dynamics. Symmetric tilt grain boundaries (STGBs) are analyzed with the tilt plane oriented along each major crystallographic axis, for a total of eighty unique grain boundaries. The effect of temperature, tilt plane, and misorientation angle on interfacial energies are analyzed. The interfacial energies typically increase with temperature and there is significant variance as a function of misorientation angle, irrespective of the tilt plane. At 500 K, the average surface energy (1.23 J/m 2 ) is approximately 1.5 times the grain boundary energy (0.79 J/m 2 ), and the work of adhesion is approximately twice the grain boundary energy (1.68 J/m 2 ). Orientations for the likely formation of twins and likely failure planes are identified.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Microstructure analysis of laser beam weldments performed on neutron-irradiated 304L steel containing 3 and 8 appm helium

We report that AISI 304 L austenitic stainless steel is one of the major structural materials used in light water reactors (LWRs). In the future, 304 L components may require repair, and several welding techniques have been proposed as candidates. In this study, laser beam welding using the low-energy contribution approach was performed in ~2016 on neutron-irradiated AISI 304 L steel with nominal values of 3 and 8 appm helium (He). The goal was to investigate the impact of helium on the irradiated material weldability and evaluate helium-associated damage. The weld and heat-affected zone (HAZ) microstructure was studied using scanning electron microscopy, electron backscatter diffraction, and transmission electron microscopy (TEM). Analysis of the weldment cross-sections did not reveal severe cracking. Still, evidence of incipient helium-associated damage was observed in the HAZ, manifesting as degraded grain boundaries (GBs) “decorated” by pore chains and mostly small (i.e., ≤ 25-30 µm) scattered cracks. The largest observed crack was ~50 µm in length. Helium-associated damage was localized within ~200-300 µm of the weld pool boundary, and the fraction of the compromised GBs, as a rule, was below ~9-11% of the total GB network. TEM analysis showed significant annealing of the radiation-induced defects at distances up to ~300 µm from the weld pool boundary. Inside the HAZ, the cavities (likely, helium bubbles) tended to form at GBs and inclusions, such as manganese sulfide precipitates in the grain interior. Crystallography analysis of the HAZ damage showed that random high-angle boundaries were most susceptible to helium-associated damage. In contrast, low-angle random boundaries and twin boundaries appeared to be strongly resistant to degradation from the combined effects of helium and welding.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Molecular dynamics studies of helium bubble effects on grain boundary fracture vulnerabilities in an Fe 70 Ni 11 Cr 19 –1%H austenitic stainless steel

Comprehensive molecular dynamics tensile test simulations have been performed to study the delamination processes of seven different grain boundaries / cleavage planes (Σ1{111}, Σ3{111}, Σ5{100}, Σ7{111}, Σ9{411}, Σ11{311}, and R{100}/{411}) containing a helium bubble. Combinations of a variety of conditions are explored including different strain rates, system dimensions, bubble density, bubble radius, bubble pressure, and temperature. We found that in general, grain boundaries absorb less energies with decreasing strain rate but increasing bubble areal density, bubble pressure, bubble radius, and temperature. The propensity of grain boundary delamination is sensitive to grain boundary type: The random grain boundary R{100}/{411} is one of the most brittle boundaries whereas the Σ1{111} cleavage plane and the Σ3{111} twin boundary are two of the toughest boundaries. The sorted list of grain boundary fracture vulnerability obtained from our dynamic tensile test simulations differs from the one obtained from our decohesion energy calculations, confirming the important role of plastic deformation during fracture. Finally, detailed mechanistic analyses are performed to interpret the simulated results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Determination of single crystal thermal expansion in Uranium-6wt%Niobium shape memory alloy using in-situ diffraction and modeling of textured polycrystalline samples

In-situ neutron diffraction and ex-situ dilatometry experiments were performed on a chemically banded, quenched uranium-6wt% niobium shape memory alloy to study the impact of deformation-(detwinning-) induced texture on the evolution of thermally induced strains (and associated stresses). Thermal heating and cooling cycles between 5K and 473K were performed in-situ with neutron diffraction, and the lattice strain evolution is reported for the observed monoclinic α" phase. Comparisons between the measured diffraction strains and macroscopic dilatometry experiments reveal relationships between micro- and macro-level thermal expansion. Softening of the texture during heating suggests that twin boundary motion can accommodate the large internal thermal strains which are approximately 2% greater than that typically observed during the 175K heating interval used to age more randomly oriented polycrystalline material. Assuming weak constraint of neighboring grains in randomly textured polycrystals, the single crystal thermal expansion tensor is extracted from measurements of lattice strains over the range 5K to 473K. Predictions of polycrystalline thermal expansion, based upon this single crystal thermal expansion tensor, are shown to compare favorably with bulk thermal expansion observations of the as quenched microstructure. However, such a lower-bound estimate is insufficient to explain all aspects of the behavior of the textured material, where the matrix is not isotropic. In conclusion, it is hypothesized that relaxation processes which occur within the quenched microstructure during heating are responsible for the distinct thermal expansion behavior observed during the initial heating cycle compared to cooling and subsequent cycling.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Optimal sensor placement for reconstructing wind pressure field around buildings using compressed sensing

Deciding how to optimally deploy sensors in a large, complex, and spatially extended structure is critical to ensure that the surface pressure field is accurately captured for subsequent analysis and design. In some cases, reconstruction of missing data is required in downstream tasks such as the development of digital twins. Here, this paper presents a data-driven sparse sensor selection algorithm, aiming to provide the most information contents for reconstructing aerodynamic characteristics of wind pressures over tall building structures parsimoniously. The algorithm first fits a set of basis functions to the training data, then applies a computationally efficient QR algorithm that ranks existing pressure sensors in order of importance based on the state reconstruction to this tailored basis. The findings of this study show that the proposed algorithm successfully re- constructs the aerodynamic characteristics of tall buildings from sparse measurement locations, generating stable and optimal solutions across a range of conditions. As a result, this study serves as a promising first step toward leveraging the success of data-driven and machine learning algorithms to supplement traditional genetic algorithms currently used in wind engineering.

42 ENGINEERING↗
DOE OSTI2025

Numerical and experimental analysis of mechanically induced failure in electric vehicle battery modules

Mitigating thermal runaway and cell-to-cell propagation is essential for improving the safety of electric and hybrid vehicles. Enhancing digital twin capabilities to predict battery mechanical abuse is particularly critical for automotive and aerospace applications, where crashworthiness is a key concern. Understanding failure conditions and propagation in battery modules during mechanical abuse is complex due to interactions between structural deformation, heat transfer, electrochemical processes, exothermic reactions and mechanical fracture. While prior studies have focused on modeling cell-level behavior, extending these models to module or pack level is necessary for a system level understating of electric vehicle safety. This study develops coupled large deformation finite element models that simultaneously solve for electrochemistry, material failure, internal short circuit and thermal runaway propagation. The models account for mechanical and thermal interactions between lithium-ion cells and other battery components while the contact interfaces are evolving with time. Model-predicted voltage, temperature and force responses are compared with experimental data for validation. The results demonstrate that the approach captures key failure mechanisms, including thermal propagation through heat transfer, electrical propagation from short circuits in parallel-connected cells, and mechanical propagation via penetration and crack formation. These findings show that computational models are valuable tools for understanding battery module failure and providing insight that can reduce the need for extensive experimental testing.

25 ENERGY STORAGE↗
DOE OSTI2023

Automated phase segmentation and quantification of high-resolution TEM image for alloy design

In the alloy design and development process, a wealth of atomically resolved structural high-resolution transmission electron microscopy (HRTEM) images are produced. Identifying the different nano-precipitate phases and tracking their evolution under various compositions and during manufacturing or post-processing requires hundreds of HRTEM images and thousands of precipitates. The nanoscopic phase information labeling and analysis purely relies on humans are prohibitively costly and time-consuming, sometimes not reliable because of the lack of authoritative knowledge. Here, in this work, we develop a novel unsupervised machine learning approach coupled with adaptive computer vision techniques with features in the Fourier space to automatically determine the number of phases and segment/quantify the phases with nanoscale resolution, allowing for quantitative correlation between nanostructure formation, processing and functional properties. To automate the phase extraction/quantification and ascertain its applicability, we have applied the developed framework to the HRTEM images from several alloy systems, processing conditions, image magnifications, and phase types and morphologies (precipitates, nano-twins, stacking faults, crystalline matrix, and amorphous structures) for verification. This study paves the road for compression, visualization, and translation of raw image structural data into physically relevant information in real-time with minimal human supervision. It shows the promise of enabling high-throughput materials characterization for the acceleration of alloy manufacturing and design.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Rapid grain refinement and compositional homogenization in a cast binary Cu50Ni alloy achieved by friction stir processing

Friction stir processing (FSP) has been increasingly adopted for joining and processing materials in automotive, aerospace and industrial construction. During FSP a dynamic competition between high-speed shear deformation and deformation-induced heating brings about a complex competition between multiple dynamic microstructural evolution mechanisms making it difficult to predict the microstructural evolution pathway. Hence, improved understanding of microstructural evolution mechanisms during FSP can be beneficial for continued growth in the adoption of FSP for demanding applications of future. Towards this goal, this study uses a model binary Cu – 50 at.% Ni alloy to clarify the effect of single and double pass FSP on the microstructural evolution of a coarse grained and compositionally heterogeneous cast microstructure. High energy synchrotron X-ray diffraction, electron backscatter diffraction, and nanoindentation are used to clarify the microstructural evolution due to FSP. The process of compositional homogenization of as-cast segregations is studied by energy dispersive spectroscopy and atom probe tomography. Our results show that a single fast FSP pass at 30 mm.s -1 produces a 100 µm deep layer of submicrometric and hall-petch hardened CuNi grains. The initial cast compositional heterogeneities in a micrometric scale is rapidly transformed to nano-sized domains, mainly confined at grain boundaries. Double pass FSP increases the penetration depth of the processed layer and leads to a 2.9 times grain growth relative to single pass FSP. Grain fragmentation, discontinuous dynamic recrystallization, grain growth, and twinning mechanisms are discussed. In conclusion, these results highlight the value of FSP for ultrafast grain refinement and compositional homogenization of cast alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The impact of nickel concentration and stacking fault energy on deformation mechanisms in high-purity austenitic Fe-Cr-Ni alloys

Understanding how composition affects deformation mechanisms in austenitic stainless steels is essential for developing accurate predictive models of stress-induced failures and stress corrosion cracking. Nickel (Ni), an element classified as a critical element, plays a crucial role in these processes. It is important to examine how Ni concentration influences stacking fault energy (SFE) and, consequently, the deformation mechanisms of austenitic stainless steels. However, in commercial stainless steels, the effects of other alloying elements and impurities can obscure Ni's role, complicating efforts to isolate its impact. Here, in this study, we use two high-purity Fe-Cr-Ni alloys to investigate how Ni concentration and SFE interact to alter deformation mechanisms and induce martensitic transformation. By combining in situ synchrotron X-ray diffraction (XRD) tensile testing and post-mortem electron microscopy with density functional theory simulations, we gain precise insights into these phenomena. We find that the Fe18Cr10Ni (wt%) alloy, with its low SFE, exhibits higher stacking fault probability, deformation-induced martensitic transformation, and a lesser increase in dislocation density with plastic strain. In contrast, the Fe18Cr14Ni (wt%) alloy, with its higher SFE, shows enhanced deformation twinning and greater dislocation density with increasing strain. These findings from high-purity ternary alloys provide valuable insights that can guide the search for alternative elements to replace Ni while achieving similar effects on phase stability and deformation behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Experimental investigation of the dependence of void nucleation and growth on initial microstructure in high-purity titanium under tension

An experimental investigation of failure mechanisms in relation to the initial microstructure in high-purity titanium samples is presented. The initial microstructure of the specimens was measured in 3D using diffraction-contrast tomography (DCT). Ex-situ X-ray computed tomography (XCT) was used to visualize voids in specimens at various levels of deformation attained by interrupted tensile testing. Electron backscatter diffraction (EBSD) mapping was used to characterize the deformed microstructures per specimen. The investigation showed that the location of failures was unrelated to the formation of the first voids, but rather the nucleation and growth of cracks were from heavily deformed surface regions. The areas surrounding the failure-causing cracks had the highest propensity for void development of any area in the specimen. This facilitated crack propagation through the specimen via “linking up”. The failure of the specimens by microvoid coalescence was bolstered by “dimpled” fracture surfaces. Paint composed of gallium embedded in rubber was used to track the displacement of points along the loading direction of the specimens, to relate the location of failure to the material's initial microstructure. However, the correlation proved difficult, due to complex microstructural evolution involving voids, grain fragmentations, and profuse twinning. Nevertheless, it was shown that necking occurred near the largest grain in the gauge section of the specimens. This is likely caused by the decrease in strength of larger grains, causing strain to concentrate in their vicinity. Here, a comprehensive picture of the failure processes in high-purity titanium under axial loading is presented and discussed in the paper.

36 MATERIALS SCIENCE↗