Test and evaluation of fuel cell catalysts Final report, 3 May 1967 - 3 May 1968
Corrosion resistance and anode activity data on interstitial compounds for fuel cell catalysts
Flannery, R. J.↗
SEARCH · Engineering Papers
Results for “Test Data Report”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Applicability of remote sensor data to geologic analysis of the Bonanza test site Colorado
There are no author-identified significant results in this report.
Knepper, D. H., Jr.↗
A statistical test procedure for detecting multiple outliers in a data set
There are no author-identified significant results in this report.
Chhikara, R. S.↗
Large-area high-efficiency ion-implanted cells and flat-plate modules
This paper reports the development of a flat-plate module based on highly efficient ion-implanted silicon solar cells. The cells are 53 sq cm in area and have exhibited AM 1.5 efficiencies of over 18 percent. The use of back surface reflectors to reduce module operating temperature is discussed. A comparison of various approaches to cell design is made, and module test data for these designs are presented. Module efficiency of 14 percent (25 C) is reported.
Spitzer, M. B.↗
Joint Eglin Acoustics Week 2013 Data Report
Far-field acoustic measurements were obtained for the AH-64D, HH-60M and CV-22B at the Eglin AFB, Test Area C-72, in July/August 2013. The primary purpose for this flight test was to obtain a benchmark database of detailed acoustic source noise characteristics for the aircraft operating at typical mission gross weights over a range of typical mission operating conditions. Data were acquired for a range of steady-state level and descending flight conditions, hover, and a variety of unsteady maneuver conditions. Between 30 and 37 microphones were deployed during these tests. Vehicle position and state data, as well as weather data were acquired simultaneously with the acoustic data. This paper describes the test aircraft, onboard instrumentation, ground instrumentation, and the data acquired. Data from this test are available upon request and review.
Conner, David A.↗
Mini-Canister Radiolysis Testing of ASNF Materials and Surrogates
An experimental irradiation campaign to investigate radiolysis behavior of ASNF was conducted using in situ gas monitoring of small, sealed stainless-steel vessels (mini-canisters) containing aluminum samples with adherent (oxy)hydroxide films under helium backfill. The samples were irradiated with gamma radiation from a Co-60 irradiator. The samples tested included aluminum plate assemblies with lab-grown (oxy)hydroxides as surrogates for fuel as well as an end cropping from an actual ASNF assembly retrieved from long-term wet storage. These experiments enabled investigation of the impacts of various fuel drying approaches on the radiolytic generation rate and measurement of the H 2 yield associated with a reactor exposed sample with reactor-formed (oxy)hydroxide. The resulting data can be incorporated into model development for ASNF in dry storage. This report presents the cumulative results from four surrogate assemblies tested after application of different preparation (drying) conditions as well as the ASNF cropping; some post-irradiation testing was included. The mini-canister results are compared to data from related experimental campaigns that also tested the impact of drying conditions using samples irradiated in glass ampoules and discusses implications of the combined data
12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
Results of Tests on Radiators for Aircraft Engines
Part 1 is to present the results of tests on 56 types of core in a form convenient for use in the study of the performance of and possible improvements in existing designs. Working rules are given by which the data contained in the report may be used, and the most obvious conclusions as to the behavior of cores are summarized. Part 2 presents the results of tests made to determine the pressure necessary to produce water flows up to 50 gallons per minute through an 8-inch square section of radiator core. These data are of special value in evaluating the hydraulic head against which the circulating pump is required to operate.
Dickinson, H C↗
A simplified approach for creep damage and remaining life calculation for materials surveillance in advanced reactors
High temperature reactor materials will experience a combination of mechanical degradation caused by creep and fatigue and environmental degradation caused by neutron irradiation and, in some cases, exposure to corrosive coolants. A materials surveillance program is one option for ensuring the safe, reliable operation of key reactor components under these conditions. Such a program would monitor the degradation in key material properties over time, using this data to predict how changes in the material properties affect components performance. This could then be used to make plant operational decisions and support eventual plant license extensions. Past work de-scribes such a material surveillance program based on passively actuated mechanical test articles that impose creep-fatigue type loading on test materials driven only by changes in temperature, for example those experienced by components under standard operating cycles. This report focuses on two aspects of the proposed material surveillance program: how to design the test articles to mimic the mechanical response of the corresponding component and how to use ex-situ test data to deter-mine the amount of damaged experienced by the test article (and hence the corresponding compo-nent) in service. Specifically, this report derives and validated simplified methods for both tasks, replacing earlier, more complicated approaches based on simulating the test article response and finding the best specimen design or current damage via complex numerical optimization. The sim-plified methods for each task developed here can be implemented in spreadsheet software and are simple enough for practical use in future operating plants. This report derives the methods (one for sizing and two options for damage inference), verifies the simplified approaches versus more so-phisticated methods, and compares the results of applying the simplified methods to previous re-sults using the complex numerical optimization approach. The report also provides a worked sam-pled problem applying the simplified techniques to a realistic high temperature reactor component.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Experiences with a Flexible User Research Process to Build Data Change Tools
Scientific software development processes are understood to be distinct from commercial software development practices due to uncertain and evolving states of scientific knowledge. Sustaining these software products is a recognized challenge, but under-examined is the usability and usefulness of such tools to their scientific end users. User research is a well-established set of techniques (e.g., interviews, mockups, usability tests) applied in commercial software projects to develop foundational, generative, and evaluative insights about products and the people who use them. Currently these approaches are not commonly applied and discussed in scientific software development work. The use of user research techniques in scientific environments can be challenging due to the nascent, fluid problem spaces of scientific work, varying scope of projects and their user communities, and funding/economic constraints on projects.In this paper, we reflect on our experiences undertaking a multi-method user research process in the Deduce project. The Deduce project is investigating data change to develop metrics, methods, and tools that will help scientists make decisions around data change. There is a lack of common terminology since the concept of systematically measuring and managing data change is under explored in scientific environments. To bridge this gap we conducted user research that focuses on user practices, needs, and motivations to help us design and develop metrics and tools for data change. This paper contributes reflections and the lessons we have learned from our experiences. We offer key takeaways for scientific software project teams to effectively and flexibly incorporate similar processes into their projects.
97 MATHEMATICS AND COMPUTING↗
Metal Scrap Upcycling with Shear Assisted Processing and Extrusion (ShAPE)
The overarching objective of this project is to convert metal scraps, such as aluminum, titanium, and other alloys provided by the industry, into extruded tubing, wires, and rods. Upcycling of scrap will be accomplished using Shear Assisted Processing and Extrusion (ShAPE). This approach is a new solution for recycling. The specific aims of this project are as follows: 1. Receive metal scrap under a Material Transfer Agreement (MTA), in the form of billets, from select industry partners that meet the following requirements: outer diameter of 1.245 inches (+/-0.003 inches), inner diameter drilled with a 0.404-inch drill bit, and a length of 4.0 inches (+/-0.01 inches). The billet must be cast or compacted to greater than 98% density. If the industry partner does not have the capabilities to prepare the billets, PNNL can make introductions to third-party entities as needed. Industry partners will also provide a composition analysis as weight percent. 2. Extrude metal scrap via the ShAPE process at PNNL. 3. Evaluate and benchmark the extrudate material properties per the ASTM B557-15 – Testing Tubulars Standard or similar wire and rod standards. 4. Characterize the extrudate microstructure for any of the following: grain size, second phase composition, and texture. Additional testing may include corrosion per the ASTM B117 standard and electro-potential. 5. Deliver specimens to industry partners under an MTA for additional third-party evaluations. Industry partners will, in return, provide a non-proprietary report on any testing, including testing per the ASTM B557-15, ASTM B117, and other industry standards. 6. PNNL will develop data and insights to support intellectual property capture, a published non-proprietary technical report, research collaborations, and commercialization opportunities.
36 MATERIALS SCIENCE↗
Summary of AH-1G flight vibration data for validation of coupled rotor-fuselage analyses
Under a NASA research program designated DAMVIBS (Design Analysis Methods for VIBrationS), four U. S. helicopter industry participants (Bell Helicopter, Boeing Vertol, McDonnell Douglas Helicopter, and Sikorsky Aircraft) are to apply existing analytical methods for calculating coupled rotor-fuselage vibrations of the AH-1G helicopter for correlation with flight test data from an AH-1G Operational Load Survey (OLS) test program. Bell Helicopter, as the manufacturer of the AH-1G, was asked to provide pertinent rotor data and to collect the OLS flight vibration data needed to perform the correlations. The analytical representation of the fuselage structure is based on a NASTRAN finite element model (FEM) developed by Bell which has been extensively documented and correlated with ground vibration tests.The AH-1G FEM was provided to each of the participants for use in their coupled rotor-fuselage analyses. This report describes the AH-1G OLS flight test program and provides the flight conditions and measured vibration data to be used by each participant in their correlation effort. In addition, the mechanical, structural, inertial and aerodynamic data for the AH-1G two-bladed teetering main rotor system are presented. Furthermore, modifications to the NASTRAN FEM of the fuselage structure that are necessary to make it compatible with the OLS test article are described. The AH-1G OLS flight test data was found to be well documented and provide a sound basis for evaluating currently existing analysis methods used for calculation of coupled rotor-fuselage vibrations.
Dompka, R. V.↗
An interdisciplinary analysis of ERTS data for Colorado mountain environments using ADP techniques. An early analysis of ERTS-1 data
There are no author-identified significant results in this report. The principal problem encountered has been the lack of good quality, small scale baseline photography for the test areas. Analysis of the ERTS-1 data for the San Juan Site will emphasize development of a preliminary spectral classification defining grass cover categories, and then selection of subframes for intensive investigation of the forestry, geologic, and hydrologic properties of the area. Primary work has been devoted to the selection and digitization of areas for topographic modeling, and compilation of ground based data maps necessary for computer analysis. Study effort has emphasized: geomorphic features; macro-vegetation; micro-vegetation; snow-hydrology; insect/disease damage; and blow-down. Analysis of a frame of the Lake Texoma area indicates a great deal of potential in the analysis and interpretation of ERTS imagery. Preliminary results of investigations of geologic, forest, range, cropland, and water resources of the area are summarized.
Hoffer, R. M.↗
Flow Induced Vibration Studies in Pressurized Helium Gas Cooling Channels
Production of metastable Technetium-99 (Tc-99m), a radioactive tracer that emits gamma rays, is vital to the medical imaging community. Tc-99m is extracted from the decay of Molybdenum-99 (Mo-99) which has a half-life of about 2-3 days. The work presented in this report is part of the NNSA’s mission to produce Mo-99 commercially, within the US, without the use of highly enriched uranium (HEU) in support of nonproliferation and global security. Los Alamos National Laboratory (LANL) is working with NorthStar Medical Radioisotopes (NMR) on their efforts to produce Mo-99 through the irradiation of Mo-100 targets using an electron beam. The NMR target comprises a stack of approximately 60-70 Mo-100 disks with diameter 24 mm and thickness 0.74 mm held in stainless steel laminations, each separated using 0.25 mm thick stainless steel spacers. The symmetric target stack is housed in an Inconel vessel with two Inconel windows on either side. Two electron accelerators are used to produce 40 MeV, 3.16 µA electron beams each that penetrate the Inconel windows and irradiate the Mo-100 disks. Approximately 90% of the total 250 kW beam power is deposited in the NMR target during the irradiation process. During irradiation, pressurized helium gas flows through 0.25 mm thin gaps between the disks cooling the beam window, target disks, disk laminations and spacers. Both NMR and LANL have found during cold testing of the target system (no heat deposition) that the Mo-100 disks undergo significant mass loss and disk breakage due to vibrations induced by the flowing helium gas. The mass loss is not only undesirable due to monetary loss from reduced final quantities of Mo-99, but also due to the hazards associated with radioactive material trapped in the cooling lines and particle filters. The effect of flow rate and target geometry on the flow induced vibrations need to be quantified, and recommendations provided to minimize this mass loss. This work describes LANL’s experimental characterization of the flow induced vibrations and disk mass loss in a reduced scale set-up containing 10 Mo-100 disks. We use high speed imaging, displacement measurements and microphone measurements combined with signal processing to estimate the vibration frequency of each disk. The effect of disk thickness, target fit and duration of testing on the mass loss is described. We find that in the current configuration of NMR targets, the vibrations and mass loss on the first disk are minimized, while those in the adjacent disks are highest. The microphone and high-speed image data show that increased flow rates and increased duration of testing increases vibration frequency and mass loss. The mass loss is due to both disk rotation and back and forth motion. There are visible wear marks on the disks with the highest mass loss. We also note that the current NMR window gap reduces flow induced vibrations compared to the previous smaller gaps. Longer duration testing will provide more data and verification for the findings presented in this report. The work will be continued in FY 24.
43 PARTICLE ACCELERATORS↗
Research and Test Reactor Fuels
PRO-RR is the research reactor focused program element of the broader Proliferation Resistance Optimization program (PRO-X) under the National Nuclear Safety Administration (NNSA) in the U.S. Department of Energy (DOE). PRO-X provides a framework for integrating proliferation resistance in nuclear system designs to minimize weapons usable nuclear materials (WUNM) production and diversion pathways while optimizing systems performance for peaceful use missions. PRO-RR applies the PRO-X mission objectives to research reactor system design. This document serves as one of the foundational documents for the PRO-RR-Fuel System Design technical team by documenting current research reactor fuels usage. The PRO-RR-Fuel System Design technical team consists of subject matter experts from Argonne National Laboratory (Argonne) and Savannah River National Laboratory (SRNL). In order to determine the preferred fuel of use in upcoming research and test reactors to optimize proliferation resistance, performance, and safety, it is useful to assess the fuels that have been used in the past, or are currently in use. This report reviews the historical and current fuels used in research and test reactors to inform future fuel selection. Chapter 2 discusses the low-enriched uranium (LEU) fuels currently in use in terms of thermal power level and utilization of the reactor. Chapter 3 summarizes the fabrication processes for common fuel types. Chapter 4 discusses in detail the fuel types in use in research and test reactors. A review of the cladding types in use is presented in Chapter 5, and a historical review of research and test reactor fuel fabricators is presented in Chapter 6. The data collection strategy used the International Atomic Energy Agency (IAEA) research reactor database [1] as a starting point. Information on the fuel used was gathered on research reactors (other than critical assemblies) that were listed as operational, planned, or in temporary shutdown in the IAEA database. Data on the fuel type, geometry, enrichment, uranium loading, cladding type, and fabricator were collected for each of the reactors available in the public domain. Sources of data included conference papers, journal articles, and facility and fabricator websites. Data on research reactors operating on LEU fuels are presented in Appendix A, while Appendix B presents data collected on all reactors at the time of publication of this report. Appendix C presents data collected on reactors that were part of the M3 research and test reactor conversion program.
21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
Evaluation of Cable Harness Post-Installation Testing
The Cable Harness Post-Installation Testing Report was written in response to an action issued by the Ares Project Control Board (PCB). The action for the Ares I Avionics & Software Chief Engineer and the Avionics Integration and Vehicle Systems Test Work Breakdown Structure (WBS) Manager in the Vehicle Integration Office was to develop a set of guidelines for electrical cable harnesses. Research showed that post-installation tests have been done since the Apollo era. For Ares I-X, the requirement for post-installation testing was removed to make it consistent with the avionics processes used on the Atlas V expendable launch vehicle. Further research for the report involved surveying government and private sector launch vehicle developers, military and commercial aircraft, spacecraft developers, and harness vendors. Responses indicated crewed launch vehicles and military aircraft perform post-installation tests. Key findings in the report were as follows: Test requirements identify damage, human-rated vehicles should be tested despite the identification of statistically few failures, data does not support the claim that post-installation testing damages the harness insulation system, and proper planning can reduce overhead associated with testing. The primary recommendation of the report is for the Ares projects to retain the practice of post-fabrication and post-installation cable harness testing.
King, M. S.↗
Development, Analysis and Testing of the High Speed Research Flexible Semispan Model
This report presents the work performed by Lockheed Martin Engineering and Sciences (LMES) in support of the High Speed Research (HSR) Flexible Semispan Model (FSM) wind-tunnel test. The test was conducted in order to assess the aerodynamic and aeroelastic character of a flexible high speed civil transport wing. Data was acquired for the purpose of code validation and trend evaluation for this type of wing. The report describes a number of activities in preparing for and conducting the wind-tunnel test. These included coordination of the design and fabrication, development of analytical models, analysis/hardware correlation, performance of laboratory tests, monitoring of model safety issues, and wind-tunnel data acquisition and reduction. Descriptions and relevant evaluations associated with the pretest data are given in sections 1 through 6, followed by pre- and post-test flutter analysis in section 7, and the results of the aerodynamics/loads test in section 8. Finally, section 9 provides some recommendations based on lessons learned throughout the FSM program.
Schuster, David M.↗
Hybrid Wing Body Model Identification Using Forced-Oscillation Water Tunnel Data
Static and dynamic testing of the NASA 0.7 percent scale Hybrid Wing Body (HWB) configuration was conducted in the Rolling Hills Research Corporation water tunnel to investigate aerodynamic behavior over a large range of angle-of-attack and to develop models that can predict aircraft response in nonlinear unsteady flight regimes. This paper reports primarily on the longitudinal axis results. Flow visualization tests were also performed. These tests provide additional static data and new dynamic data that complement tests conducted at NASA Langley 14- by 22-Foot Subsonic Tunnel. HWB was developed to support the NASA Environmentally Responsible Aviation Project goals of lower noise, emissions, and fuel burn. This study also supports the NASA Aviation Safety Program efforts to model and control advanced transport configurations in loss-of-control conditions.
Murphy, Patrick C.↗
Runway Incursion Prevention System ADS-B and DGPS Data Link Analysis Dallas-Fort Worth International Airport
A Runway Incursion Prevention System (RIPS) was tested at the Dallas - Ft. Worth International Airport in October 2000. The system integrated airborne and ground components to provide both pilots and controllers with enhanced situational awareness, supplemental guidance cues, a real-time display of traffic information, and warning of runway incursions in order to prevent runway incidents while also improving operational capability. Rockwell Collins provided and supported a prototype Automatic Dependent Surveillance - Broadcast (ADS-B) system using 1090 MHz and a prototype Differential GPS (DGPS) system onboard the NASA Boeing 757 research aircraft. This report describes the Rockwell Collins contributions to the RIPS flight test, summarizes the development process, and analyzes both ADS-B and DGPS data collected during the flight test. In addition, results are report on interoperability tests conducted between the NASA Advanced General Aviation Transport Experiments (AGATE) ADS-B flight test system and the NASA Boeing 757 ADS-B system.
Timmerman, J.↗