Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STRESS AND LOAD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

National Spherical Torus eXperiment - Upgrade NSTX-U: Structural Analysis of Passive Plates Support Brackets

The objective of this analysis is to estimate and assess the stresses in the passive plates caused by a limiting plasma disruption. The objective of this calculation is also to address observed damage to mounting hardware after completion of NSTX operation. These observations initiated diagnostic efforts during the Upgrade project to monitor the severity of the disruptions that were causing the damage, and planned instrumentation to trend the behavior of the mounting hardware. The Recovery Project mission for the passive plate hardware is to appropriately reinforce the passive plates with stainless steel ribs mounted on the back of the plate to reduce their flexure and stress and reinforcements of the “biscuit” components of the bracketry to transfer loads without damage to bolts, biscuits, and bracket plates and welds. Mid-plane disruptions and quenches were manageable with NSTX vintage hardware. The Vertical Displacement Event (VDE) disruptions position the plasma closer to the passive plates and are more severe than the centered plasma. Earlier work pointed to the P1-P5 VDE as limiting. This has been confirmed by A. Brooks work in support of the load generation effort in reference. During vertical displacement large counter currents are generated in the plate as the plasma approaches it. - as would be expected from passive plates. When the plasma disrupts the currents in the plates are reversed, which also reverses the loading on the plates. This report documents the methodology and results of transient structural analysis on the plasma, passive plates support brackets. The loads induced by eddy and halo currents have been considered, and were generated using a separate electromagnetic analysis (NSTXU_1_11_2_1_CALC_051). The structural model also incorporates the effects from preload. Calculation was performed with the assumption that existing biscuits are not participating in the load bearing except the biscuits connected to jumper bolts, which are fully engaged. Results show that with the planned reinforcements, Passive plates and mounting structures satisfy static and fatigue criteria in all areas except welds, where separate analysis was performed. Both symmetric and asymmetric (with locating block) designs were analyzed, and although stresses were higher without locating block they still satisfy NSTX design criteria.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mullins effect in a filled elastomer under uniaxial tension

Modulus softening and permanent set in filled polymeric materials due to cyclic loading and unloading, commonly known as the Mullins effect, can have a significant impact on their use as support cushions. The quantitative analysis of such behavior is essential to ensure the effectiveness of such materials in long-term deployment. In this work we combine existing ideas of filler-induced modulus enhancement, strain amplification, and irreversible deformation within a simple non-Gaussian constitutive model to quantitatively interpret recent measurements on a relevant PDMS-based elastomeric cushion. Also, we find that the experimental stress-strain data is consistent with the picture that during stretching (loading) two effects take place simultaneously: (1) the physical constraints (entanglements) initially present in the polymer network get disentangled, thus leading to a gradual decrease in the effective cross-link density, and (2) the effective filler volume fraction gradually decreases with increasing strain due to the irreversible pulling out of an initially occluded volume of the soft polymer domain.

36 MATERIALS SCIENCE↗

Evaluating methods to reduce duration of near-threshold fatigue crack growth rate measurements for low-alloy steels in hydrogen gas

Measurement of the near-threshold fatigue crack growth rate (da/dN) vs. stress-intensity factor range (∆K) relationship in hydrogen gas is essential for maximizing the calculated design fatigue life of high-pressure hydrogen storage vessels. However, such measurements are rarely performed, since the low cyclic loading frequencies applied in standard practice lead to prohibitively protracted test durations. The objective of this study was to demonstrate two means for reducing test durations when measuring near-threshold da/dN vs. ΔK relationships under decreasing ΔK for low-alloy pressure vessel steels in hydrogen gas: 1) imposing steeper K-gradients relative to the recommended limits in standards such as ASTM E647, and 2) increasing cyclic loading frequency relative to typical values applied during fatigue crack growth testing of low-alloy steels in hydrogen gas. Recognizing that steeper K-gradients could amplify loading-history effects, test methods employing this approach were designed to mitigate such effects by either maintaining constant K max or gradually increasing the K-gradient as the threshold was approached. Although the varying K-gradient method was vulnerable to loading-history effects in the form of plasticity-induced crack closure, particularly at lower stress ratio (R) and higher starting K max values, these effects could be compensated by applying the adjusted compliance ratio (ACR) method. Here, it was demonstrated that steeper K-gradients in concert with increased cyclic loading frequency reduced the duration of near-threshold fatigue crack growth tests in hydrogen gas by more than 99% relative to standard practices.

Fatigue threshold↗

Mechanical Behavior Analysis of a Test Coil for MICE Coupling Solenoid during Quench

The coupling magnet for the Muon Ionization Cooling Experiment has a self-inductance of 592 H and the magnet stored energy of 13 MJ at a full current of 210 A for the worst operation case of the MICE channel. The high level of stored energy in the magnet can cause high peak temperature during a quench and induce considerable impact of stresses. One test coil was built in order to validate the design method and to practice the stress and strain situation to occur in the coupling coil. In this study, the analysis on stress redistribution during a quench with sub-divided winding was performed. The stress variation may bring about failure of impregnating material such as epoxy resin, which is the curse of a new normal zone arising. Spring models for impregnating epoxy and fiber-glass cloth in the coil were used to evaluate the mechanical disturbance by impregnated materials failure. This paper presents the detailed dynamic stress and stability analysis to assess the stress distribution during the quench process and to check whether the transient loads are acceptable for the magnet.

42 ENGINEERING↗

Woven ceramic matrix composite surrogate model based on physics-informed recurrent neural network

A recurrent neural network (RNN) based surrogate model is developed to emulate the nonlinear constitutive behavior of woven ceramic matrix composites (CMCs) driven by matrix damage at multiple length scales. Physics-informed constraints are introduced into the surrogate model through regularization to ground the prediction in physics and improve its predictive capabilities. Training data is generated using the multiscale generalized method of cells (MSGMC) approach coupled with a matrix damage model. This coupling permits simulating the nonlinear behavior of woven CMCs based on constituent response at the micro-, meso-, and macroscales. The multiscale repeating unit cell is loaded under non-monotonic conditions including multiple load / unload cycles and tension / compression. The fiber volume fraction as well as the intra- and intertow void volume fractions are also varied in the generation of training data. Therefore, the RNN-based surrogate model is tasked with predicting, as a function of variable input strain sequence and fiber and void volume fractions, the resulting stress versus strain response while satisfying physical constraints such as positive semi-definiteness of the tangent stiffness matrix and linear elastic unloading. Further, the trained surrogate model effectively matches the stress versus strain response and successfully predicts the tangent modulus throughout the loading regime. Neural network based surrogate models can offer efficient alternatives to running computationally intensive multiscale material models to simulate the nonlinear response of large structural models. Therefore the presented work provides evidence towards the feasibility of developing, training, and running such models for CMCs with complex architectures, nonlinear multiaxial material response, and under non-monotonic loading conditions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

CRADA Final Report: Weld Predictor App

Welding is an important manufacturing process used in a broad range of industries and market sectors, including automotive, aerospace, heavy manufacturing, medical, and defense. During welded fabrication, high localized heat input and subsequent rapid cooling result in the creation of residual stresses and distortion. These residual stresses can significantly affect the fatigue resistance, cracking behavior, and load-carrying capacity of welded structures during service. Further, additional fitting and tacking time is often required to fit distorted subassemblies together, resulting in non-value added cost. Using trial-and-error methods to determine which welding parameters, welding sequences, and fixture designs will most effectively reduce distortion is a time-consuming and expensive process. For complex structures with many welds, this approach can take several months. For this reason, efficient and accurate methods of mitigating distortion are in-demand across all industries where welding is used. Analytical and computational methods and commercial software tools have been developed to predict welding-induced residual stresses and distortion. Welding process parameters, fixtures, and tooling can be optimized to reduce the HAZ softening and minimize weld residual stress and distortion, improving performance and reducing design, fabrication and testing costs. However, weld modeling technology tools are currently accessible only to engineers and designers with a background in finite element analysis (FEA) who work with large manufacturers, research institutes, and universities with access to high-performance computing (HPC) resources. Small and medium enterprises (SMEs) in the US do not typically have the human and computational resources needed to adopt and utilize weld modeling technology. To allow an engineer with no background in FEA and SMEs to gain access to this important design tool, EWI and the Ohio Supercomputer Center (OSC) developed the online weld application software tool “WeldPredictor” ( https://eweldpredictor.ewi.org ). About 1400 users have tested this application. This project marked the beginning of development on the next version of WeldPredictor that addresses many outstanding features of the original, including 3D models, allow more material hardening laws, model material phase transformation, and uses open source finite element solvers to quickly solve problems (as opposed to expensive commercial tools).

42 ENGINEERING↗

ON THE ESTIMATION OF THERMAL STRAINS DEVELOPED DURING OXIDE GROWTH

This paper presents results for the strains and stresses in oxide scales under the conditions of temperature and pressure expected in typical steam boiler operation. These conditions are radically different from those typically encountered in laboratory testing, and include features such as a thermal gradient across the tube wall, significant internal (steam) pressure, and cycling of both steam temperature and pressure. Critical examination of the assumptions of flat plate geometry, which is usually made in calculating stresses and strains in oxide scales, indicated that only the component of the hoop strain that generates stress must be reported for the cylindrical case, and that the use of simple plane-strain is adequate for the system studied. Calculations were made for alloy T-22 with a hypothetical, single-layered oxide with appropriate properties. Typical conditions associated with transition of the boiler from full to partial load involve a decrease in both steam temperature and pressure, and these two sources of stress generation were found to exert opposite effects. The relative magnitudes of the resulting strains were used to explain the trends in strain levels calculated when the effects of thermal expansion, temperature loading, and pressure loading were superimposed.

36 MATERIALS SCIENCE↗

Load partitioning and strain-induced martensite formation during tensile loading of a metastable austenitic stainless steel.

In-situ high-energy X-ray diffraction and material modeling are used to investigate the strain-rate dependence of the strain-induced martensitic transformation and the stress partitioning between austenite and {alpha}{prime} martensite in a metastable austenitic stainless steel during tensile loading. Moderate changes of the strain rate alter the strain-induced martensitic transformation, with a significantly lower {alpha}{prime} martensite fraction observed at fracture for a strain rate of 10{sup -2} s{sup -1}, as compared to 10{sup -3} s{sup -1}. This strain-rate sensitivity is attributed to the adiabatic heating of the samples and is found to be well predicted by the combination of an extended Olson-Cohen strain-induced martensite model and finite-element simulations for the evolving temperature distribution in the samples. In addition, the strain-rate sensitivity affects the deformation behavior of the steel. The {alpha}{prime} martensite transformation at high strains provides local strengthening and extends the time to neck formation. This reinforcement is witnessed by a load transfer from austenite to {alpha}{prime} martensite during loading.

36 MATERIALS SCIENCE↗

Multi-objective surrogate-assisted calibration of CPFEM models using macroscopic response and in situ EBSD measurements of grain reorientation trajectories

Crystal plasticity finite element method (CPFEM) models are widely used to simulate the deformation behaviour of polycrystalline materials, but their calibration is often limited by their high computational cost and the non-convexity of the optimisation landscape. Here, this study develops a multi-objective surrogate-assisted calibration workflow that couples a multi-objective genetic algorithm (MOGA) with an adaptively trained deep neural network (DNN) surrogate model to efficiently identify CPFEM parameters from experimental data. The workflow is demonstrated on three crystal plasticity (CP) formulations of increasing complexity — Voce hardening (VH), two-coefficient latent hardening (LH2), and six-coefficient latent hardening (LH6) — using in situ electron backscatter diffraction (EBSD) measurements of Alloy 617 under uniaxial tensile loading. The CPFEM models are calibrated against the experimentally observed stress–strain response and reorientation trajectories of eight grains, then validated against eight additional trajectories and overall texture evolution. Across the CP formulations, the macroscopic response was reproduced reliably, while differences emerged in the robustness and accuracy of the grain-scale predictions. Including grain reorientation trajectories in the multi-objective calibration improved texture evolution predictions and filtered out physically inconsistent parameter sets that can arise from calibrating against only the stress–strain data. The workflow also demonstrates good transferability of calibrated parameters from a low- to a high-fidelity microstructural model. These results provide practical guidance for integrating in situ microstructural data into CPFEM through efficient, repeatable, and physically meaningful multi-objective calibration.

Crystal plasticity finite element method↗

Effects of internal swelling on residual elasticity of a quasi-brittle material through a composite sphere model

This work describes the development of a micromechanical-based constitutive model accounting for the effect of internal expansion on the residual elasticity of a Hashin composite material. This material is made of spherical inclusions that are subjected to gradual swelling within a quasi-brittle matrix. The main focus of this work is to describe and analyze the material mechanical response, with an additional focus on the internal swelling’s effect on the stress–strain response and residual elasticity. Microstructural features and parameters of major importance for the mechanical responses were identified. The innovative characteristics of the proposed approach are summarized as follows: (1) a full determination of the physics of a complete-damage problem throughout the whole process of inclusion swelling with upscaling techniques, which transfers the microcrack-related properties from the lower scale to upper scale; and (2) an evolution of the mechanical fields and the corresponding residual elasticity for various inclusion swelling levels. Concerning the matrix–inclusion composite, it was hypothesized that only the matrix was susceptible to cracking, with varied degrees of damage, whereas the inclusions behave elastically and the elastic modulus of the expanding inclusions remains constant. It is to emphasize that the gradual swelling of inclusions is modeled by an increasing strain in the current micromechanical-based constitutive model, and the microcracks are represented by a set of randomly oriented penny-shaped microcracks with identical radii (namely, closed cracks). The main contribution of the current research is to establish the exact mathematical solutions for the mechanical fields (stress, strain) caused by the swelling of the inclusions (mechanical loading) and derive the effective residual elasticity of a composite (structural response) subject to internal expansion and quasi-brittle damage. Based on the assumption of closed cracks that could be extended to open cracks in the upcoming work, the results proposed by the present paper help to understand the non-linear mechanical behavior of quasi-brittle materials subject to microcracking and provide a theoretical framework to be used as academical benchmark for numerical simulations.

36 MATERIALS SCIENCE↗

Constitutive behavior and progressive mechanical failure of electrodes in lithium-ion batteries

The electrodes of lithium-ion batteries (LIB) are known to be brittle and to fail earlier than the separators during an external crush event. Thus, the understanding of mechanical failure mechanism for LIB electrodes (anode and cathode) is critical for the safety design of LIB cells. In this paper, we present experimental and numerical studies on the constitutive behavior and progression of failure in LIB electrodes. Mechanical tests were designed and conducted to evaluate the constitutive properties of porous electrodes. Constitutive models were developed to describe the stress-strain response of electrodes under uniaxial tensile and compressive loads. The failure criterion and a damage model were introduced to model their unique tensile and compressive failure behavior. The failure mechanism of LIB electrodes was studied using the blunt rod test on dry electrodes, and numerical models were built to simulate progressive failure. The different failure processes were examined and analyzed in detail numerically, and correlated with experimentally observed failure phenomena. Finally, the test results and models improve our understanding of failure behavior in LIB electrodes, and provide constructive insights on future development of physics-based safety design tools for battery structures under mechanical abuse.

25 ENERGY STORAGE↗

Forming Analysis of AZ31 Magnesium Alloy Sheets by Means of a Multistep Inverse Approach

This paper applies a multi-step inverse approach to predict the forming of AZ31 magnesium alloy sheets. An in-house finite element code named “INAPH”, which implements the inverse approach formulation by Guo et al. (Int. J. Numer. Methods Eng., 30, 1385-1401), has been used for the forming analysis. This inverse approach uses the deformation theory of plasticity and assumes that the deformation is independent of the loading history. Failure during forming is predicted by a stress-based criterion or a forming limit diagram-based criterion. The INAPH predictions have been compared with experimental results of Takuda et al (Journal of Materials Processing Technology, 89-90:135-140) and incremental analysis using ABAQUS. The multi-step inverse analysis has been shown to very quickly and fairly accurately predict stress, plastic strain, thickness distributions and failure locations on deeply drawn parts made of AZ31 magnesium alloy. The capability of INAPH to predict the formability of magnesium alloys has also been demonstrated at various temperatures. As magnesium alloys possess very limited formability at room temperature, and their formability becomes better at higher temperatures (> 100oC), the inverse analysis constitutes an efficient and valuable tool to predict forming of magnesium alloy parts as a function of temperature. In addition, other processing and design parameters such as the initial dimensions, final desired shape, blank holder forces, and friction can be quickly adjusted to assess the forming feasibility.

36 MATERIALS SCIENCE↗

Thin film combinatorial sputtering of TaTiHfZr refractory compositionally complex alloys for rapid materials discovery

Many applications from advanced nuclear reactors to aerospace and automotive industries require materials to operate in extreme environments. In search of new materials that can operate in these extremes, the present work explores this space whereby: (1) guided by atomistic and thermodynamic calculations we utilize thin film combinatorial synthesis to rapidly explore mechanical and thermal properties in a broad range of refractory compositionally complex alloys, and (2) observe transformation induced plasticity via oscillations in the thin film nanoindentation load depth curves that are attributed to, (3) a stress-induced HCP-to-BCC phase transformation in the resulting nanogranular microstructure, which to our knowledge has not been observed before in this alloy system; and finally (4) scale to bulk materials to compare the thin film results.

36 MATERIALS SCIENCE↗

Assessment of irradiation embrittlement effect on fatigue life of a pressurized-water reactor pressure vessel using the fracture toughness master curve approach

The reactor pressure vessel (RPV) is a critical structural component in pressurized-water reactors, and it is designed to withstand extreme conditions, such as high pressures, elevated temperatures, and prolonged radiation exposure. Ensuring RPV integrity is essential for the safe and reliable long-term operation of nuclear power plants, especially as aging mechanisms such as fatigue and irradiation embrittlement pose increased risks. Fatigue, caused by cyclic thermal and mechanical loading, can lead to crack initiation in localized high-stress regions. Simultaneously, neutron irradiation, particularly in the beltline region, progressively reduces fracture toughness, increasing susceptibility to brittle fracture. These combined effects of fatigue and irradiation embrittlement potentially impact the RPV structural integrity, necessitating fitness-for-service assessments. This study applies the fracture toughness master curve approach to evaluate the impact of irradiation embrittlement on RPV fatigue life. A coupled thermo-mechanical stress analysis identifies critical stress locations under normal service transients, pinpointing regions most vulnerable to fatigue crack initiation and growth. Stress intensity factors for postulated flaws at these locations are calculated, enabling an assessment of fatigue life under irradiated and unirradiated conditions. The results indicate that neutron irradiation embrittlement accelerates the conditions in which a critical crack can form and lead to failure, particularly at lower temperatures. The failure occurs where reduced fracture toughness limits the material’s resistance to crack growth. Axial cracks at nozzle corners are the most life limiting without irradiation, while circumferential cracks demonstrate longer fatigue lives. The findings highlight the importance of incorporating irradiation effects into fatigue life predictions to ensure the long-term structural integrity of RPVs.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

Cryostat design and analysis of the superconducting magnets for Jefferson Lab's 11-GEV/C super high momentum spectrometer

This paper describes the mechanical design and analysis of the cryostats for the two cos(2theta) quadrupoles and the cos(theta) dipole. All the magnets are currently being bid for commercial fabrication. The results of finite element analysis for the magnet cryostat helium vessels and outer vacuum chambers which investigate the mechanical integrity under maximum allowable internal working pressure, maximum allowable external working pressure, and cryogenic temperature are discussed. The allowable stress criterion is determined based on the allowable stress philosophy of the ASME codes. The computed cryogenic heat load of the magnets is compared with the allowable cryogenic consumption budget. The presented cool-down time of the magnets was studied under the conditions of a limited supply rate and a controlled temperature differential of 50 K in the magnets.

43 PARTICLE ACCELERATORS↗

Magnetic and Mechanical Design of a 15-T Large Aperture Dipole Magnet for Cable Testing

© 2019 IEEE. A large aperture Nb 3 Sn dipole is proposed to replace the magnet assembly of EDIPO, which was irreversibly damaged in 2016. The goal is to generate a background field of 15 T at 4.2 K in a clear aperture of approximately 100×150 mm 2 and over a uniform length of 1000 mm in order to test superconducting cables for both fusion and high-energy physics applications. The magnet features a block-type coil design wound with wide Rutherford cable (two alternative coil cross sections are considered) and supported by a mechanical structure based on keys-and-bladders technology. In the end regions, the coils tilt up (flare) through a hard-way bend of the cables to provide room for the test well, following a layout already adopted in the LBNL HD2 and CERN-CEA FRESCA2 magnets. The two considered coil design alternatives aim at minimizing the mechanical stress in the coil windings. One coil pack design makes the use of two double pancake coils per pole, whereas the other alternative features three double pancakes per pole. Both design options are presented focusing on the results of numerical computations carried out with finite-element models to investigate peak stresses in the coils during room-temperature pre-loading, cool down, and powering.

Sarasola, Xabier (ORCID:0000000324306939)↗

Design and Analysis of a Floating-Wind Shallow-Water Mooring System Featuring Polymer Springs

This paper presents a mooring system design featuring polymer springs for the VolturnUS-S 15-MW reference floating wind turbine in site conditions for the New York Bight at a 50-m water depth. Polymer springs have a nonlinear stress-strain curve that allows a stiffer response at low loads and a more flexible response at higher loads, potentially reducing peak mooring line tensions. The mooring dynamics model MoorDyn has been extended to model springs with nonlinear tension-strain curves from a user-inputted look-up table. This MoorDyn modeling advancement is verified against OrcaFlex simulation results. Using MoorDyn's updated capabilities, a spring-equipped catenary mooring system is designed for the 15-MW floating system, along with a baseline catenary mooring system that does not use polymer springs. The floating wind turbine simulator OpenFAST is used to simulate the mooring systems in design-driving load cases to show the effect of polymer springs on key dynamic behaviours. The results show that the spring-equipped design reduces peak tensions by up to 60%, whereas the turbine offsets stay within a maximum of 7.2 m, which is still a reasonable offset limit for cable considerations. The reduction in peak tensions results in a significant decrease in damage equivalent loads - on the order of 50% for upwind lines in fully loaded conditions. These results show that polymer springs can effectively reduce peak tensions and fatigue loads in mooring systems at shallow water depths.

floating offshore wind↗

Development of Simplified Model Test Methods for Creep-Fatigue Evaluation

The Simplified Model Test (SMT) approach is an alternative creep-fatigue evaluation method that no longer requires the use of the damage interaction diagram, or D-diagram. The reason is that the combined effects of creep and fatigue are accounted for in the test data by means of a SMT specimen that is designed to replicate or bound the stress and strain redistribution that occurs in actual components when loaded in the creep regime. However, creep-fatigue experiments on SMT key feature articles are specialized and difficult to perform by the general research community. In this paper, two innovative SMT based creep-fatigue experimental methods are developed and implemented. These newly-developed SMT test methods have resolved all the critical challenges in the SMT key feature article testing and enable the potential of further development of the SMT based creep-fatigue evaluation method into a standard testing method. Scoping test results on Alloy 617 and SS 316H using the newly developed SMT methods are summarized and discussed. The concepts of the SMT methodology for creep-fatigue evaluation are explained.

Wang, Yanli↗