Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPECIFICITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Analytical evaluation of the impact of broad specification fuels on high bypass turbofan engine combustors

Six conceptual combustor designs for the CF6-50 high bypass turbofan engine and six conceptual combustor designs for the NASA/GE E3 high bypass turbofan engine were analyzed to provide an assessment of the major problems anticipated in using broad specification fuels in these aircraft engine combustion systems. Each of the conceptual combustor designs, which are representative of both state-of-the-art and advanced state-of-the-art combustion systems, was analyzed to estimate combustor performance, durability, and pollutant emissions when using commercial Jet A aviation fuel and when using experimental referee board specification fuel. Results indicate that lean burning, low emissions double annular combustor concepts can accommodate a wide range of fuel properties without a serious deterioration of performance or durability. However, rich burning, single annular concepts would be less tolerant to a relaxation of fuel properties. As the fuel specifications are relaxed, autoignition delay time becomes much smaller which presents a serious design and development problem for premixing-prevaporizing combustion system concepts.

Taylor, J. R.↗

Mission analysis and performance specification studies report, appendix A

The Near Term Hybrid Passenger Vehicle Development Program tasks included defining missions, developing distributions of daily travel and composite driving cycles for these missions, providing information necessary to estimate the potential replacement of the existing fleet by hybrids, and estimating acceleration/gradeability performance requirements for safe operation. The data was then utilized to develop mission specifications, define reference vehicles, develop hybrid vehicle performance specifications, and make fuel consumption estimates for the vehicles. The major assumptions which underlie the approach taken to the mission analysis and development of performance specifications are the following: the daily operating range of a hybrid vehicle should not be limited by the stored energy capacity and the performance of such a vehicle should not be strongly dependent on the battery state of charge.

Source record↗

NASA/General Electric broad-specification fuels combustion technology program, phase 1

The use of broad specification fuels in aircraft turbine engine combustion systems was examined. Three different combustor design concepts were evaluated for their ability to use broad specification fuels while meeting several specific emissions, performance, and durability goals. These combustor concepts covered a range from those having limited complexity and relatively low technical risk to those having high potential for achieving all of the program goals at the expense of increased technical risk.

Dodds, W. J.↗

Measurement of the specific refractivities of CF4 and C2F6

In order to relate the measured fringe shift of an interferometer to the density of a medium, the relation between density and refractive index, which is expressed by the specific refractivity, must be known. In the present paper, the specific refractivities of the wind tunnel test gases CF4 and C2F6 are determined in order to verify estimations based on the atomic refractivities of carbon and fluorine. A Twyman-Green two-beam interferometer with a 633-nm He-Ne laser light source was used to measure the specific refractivity as a function of fringe shift as the density of the gas was changed. Values of 0.122 and 0.131 cu cm/g were obtained for CF4 and C2F6 respectively at a temperature of 300 K, which are within 1% of the values computed from the atomic refractivities.

Burner, A. W.↗

ERSYS-SPP access method subsystem design specification

The STARAN special purpose processor (SPP) is a machine allowing the same operation to be performed on up to 512 different data elements simultaneously. In the ERSYS system, it is to be attached to a 4341 plug compatible machine (PCM) to do certain existing algorithms and, at a later date, to perform other to be specified algorithms. That part of the interface between the 4341 PCM and the SPP located in the 4341 PCM is known as the SPP access method (SPPAM). Access to the SPPAM will be obtained by use of the NQUEUE and DQUEUE commands. The subsystem design specification is to incorporate all applicable design considerations from the ERSYS system design specification and the Level B requirements documents relating to the SPPAM. It is intended as a basis for the preliminary design review and will expand into the subsystem detailed design specification.

Weise, R. C.↗

NASA Broad Specification Fuels Combustion Technology program - Pratt and Whitney Aircraft Phase I results and status

In connection with increases in the cost of fuels and the reduced availability of high quality petroleum crude, a modification of fuel specifications has been considered to allow acceptance of poorer quality fuels. To obtain the information upon which a selection of appropriate fuels for aircraft can be based, the Broad Specification Fuels Combustion Technology program was formulated by NASA. A description is presented of program-related investigations conducted by an American aerospace company. The specific objective of Phase I of this program has been to evaluate the impact of the use of broadened properties fuels on combustor design through comprehensive combustor rig testing. Attention is given to combustor concepts, experimental evaluation, results obtained with single stage combustors, the stage combustor concept, and the capability of a variable geometry combustor.

Lohmann, R. P.↗

Formal specification and mechanical verification of SIFT - A fault-tolerant flight control system

The paper describes the methodology being employed to demonstrate rigorously that the SIFT (software-implemented fault-tolerant) computer meets its requirements. The methodology uses a hierarchy of design specifications, expressed in the mathematical domain of multisorted first-order predicate calculus. The most abstract of these, from which almost all details of mechanization have been removed, represents the requirements on the system for reliability and intended functionality. Successive specifications in the hierarchy add design and implementation detail until the PASCAL programs implementing the SIFT executive are reached. A formal proof that a SIFT system in a 'safe' state operates correctly despite the presence of arbitrary faults has been completed all the way from the most abstract specifications to the PASCAL program.

Melliar-Smith, P. M.↗

Material characterization and specification development for 350 F curing epoxy-graphite materials

New analytical techniques and a processability laminate have been used in the development of a material specification for 350 F curing epoxy-graphite materials. The development of the specification required the evaluation of prepregs which had variations in their processing behavior that were detected only in production. Chemical techniques were used to analyze the prepregs and establish limits on the concentrations of the various chemical constituents. A batch acceptance test laminate was designed to determine suitability of prepregs for production useage. The new specification requires that the processability laminate be ultrasonically and micrographically inspected for voids and porosity. Incorporation of these and other requirements will help to insure material consistency and processability.

Rogers, A. K.↗

IGES, a key interface specification for CAD/CAM systems integration

The Initial Graphics Exchange Specification (IGES) program has focused the efforts of 52 companies on the development and documentation of a means of graphics data base exchange among present day CAD/CAM systems. The project's brief history has seen the evolution of the Specification into preliminary industrial usage marked by public demonstrations of vendor capability, mandatory requests in procurement actions, and a formalization into an American National Standard in September 1981. Recent events have demonstrated intersystem data exchange among seven vendor systems with a total of 30 vendors committing to offer IGES capability. A full range of documentation supports the IGES project and the recently approved IGES Version 2.0 of the Specification.

Smith, B. M.↗

Site-Specific Research Conducted in Support of the Salton Sea Solar Pond Project - FY 1982 Report

The design and operation of a salt-gradient solar pond power plant at the Salton Sea presents problems not encountered at small research ponds that were built in the United States. The specific characteristics of the Salton Sea site and the desire to construct the pond using the local clay as a sealant represent major deviations from previous solar pond experience. The site-specific research in support of the plant design is described. The research activity included validation of the spectrophotometric light transmission measurement technique, a search for options for clarifying the turbid and colored water of the Salton Sea, development of water clarification specifications in terms common to industry practice, quantification of gas production from microbiological reactions in the ground, a determination of the combined effects of temperature and salinity on the permeation of the local clays, and a preliminary evaluation of material corrosion.

French, R. L.↗

Gateway design specification for fiber optic local area networks

This is a Design Specification for a gateway to interconnect fiber optic local area networks (LAN's). The internetworking protocols for a gateway device that will interconnect multiple local area networks are defined. This specification serves as input for preparation of detailed design specifications for the hardware and software of a gateway device. General characteristics to be incorporated in the gateway such as node address mapping, packet fragmentation, and gateway routing features are described.

Source record↗

An approach to developing specification measures

An approach to developing specification measures is described. A key feature of the approach is the introduction of a new requirements representation, the Composite Specification Model (CSM). Results are reported from an experiment in which the requirements for a real system are recast using the CSM. Specification measures are then extracted from the CSM representation of the system.

Agresti, W. W.↗

Investigation of specification measures for the Software Engineering Laboratory (SEL)

Requirements specification measures are investigated for potential application in the Software Engineering Laboratory. Eighty-seven candidate measures are defined; sixteen are recommended for use. Most measures are derived from a new representation, the Composite Specification Model, which is introduced. The results of extracting the specification measures from the requirements of a real system are described.

Source record↗

Specification of a NAVSTAR Global Positioning System (GPS) receiver for a differential GPS ground system

One step towards the successful completion of a functional ground unit for the Differential Global Positioning System (DGPS) will be in choosing a currently available GPS receiver that will accurately measure the propagation times of the satellite signals and have the capability to be electrically interfaced with and controlled by a Digital Equipment Corporation (DEC) PDP-11/34A computer. The minimum requirements and characteristics of a NAVSTAR Global Positioning System (GPS) receiver are described. The specific technical specifications addressed include data accuracies and resolutions, receiver interface/external control, enclosure dimensions and mounting requirements, receiver operation, and environmental specifications.

Mccall, D. L.↗

Specification for IBM/IBM compatible 3480 tape cartridge

This document establishes the same kinds of standards and controls that are currently in use for the procurement on new analog and digital magnetic tapes. The Magnetic Tape Certification Facility (MTCF) currently maintains a Quality Products List (QPL) for all new analog and digital magnetic tapes purchased by NASA-GSFC. Extensive tests are conducted in the MTCF on an annual basis to determine the manufacturer's tape types to be added to or deleted from the current QPL. The MTCF currently maintains two specifications for magnetic tapes: NASA TM-79724 is used for the QPL and acceptance testing of new analog tapes; and NASA TM-80599 is used for the QPL and acceptance testing of new digital tapes. This specification will be used for the QPL and acceptance testing of new 3480 cartridges. The magnetic tapes used by GSFC, LaRC, ARC/Dryden, WFF, and the Network Tracking Stations are covered by the NASA-GSFC specifications. The 3480 cartridge was introduced approximately 3.5 years ago and is becoming an increasingly attractive alternative to digital magnetic tapes. Many users have already converted to the 3480 system and have more tape drives on order.

Perry, Jimmy L.↗

Specification for wide channel bandwidth one-inch video tape

Standards and controls are established for the procurement of wide channel bandwidth one inch video magnetic recording tapes for Very Long Base Interferometer (VLBI) system applications. The Magnetic Tape Certification Facility (MTCF) currently maintains three specifications for the Quality Products List (QPL) and acceptance testing of magnetic tapes. NASA-TM-79724 is used for the QPL and acceptance testing of new analog tapes; NASA-TM-80599 is used for QPL and acceptance testing of new digital tapes; and NASA-TM-100702 is used for the QPL and acceptance testing of new IBM/IBM compatible 3480 magnetic tape cartridges. This specification will be used for the QPL and acceptance testing of new wide channel bandwidth one inch video magnetic recording tapes. The one inch video tapes used by the Jet Propulsion Lab., the Deep Space Network and the Haystack Observatory will be covered by this specification. These NASA stations will use the video tapes for their VLBI system applications. The VLBI system is used for the tracking of quasars and the support of interplanetary exploration.

Perry, Jimmy L.↗

A graphically oriented specification language for automatic code generation. GRASP/Ada: A Graphical Representation of Algorithms, Structure, and Processes for Ada, phase 1

The first phase of a three-phase effort to develop a new graphically oriented specification language which will facilitate the reverse engineering of Ada source code into graphical representations (GRs) as well as the automatic generation of Ada source code is described. A simplified view of the three phases of Graphical Representations for Algorithms, Structure, and Processes for Ada (GRASP/Ada) with respect to three basic classes of GRs is presented. Phase 1 concentrated on the derivation of an algorithmic diagram, the control structure diagram (CSD) (CRO88a) from Ada source code or Ada PDL. Phase 2 includes the generation of architectural and system level diagrams such as structure charts and data flow diagrams and should result in a requirements specification for a graphically oriented language able to support automatic code generation. Phase 3 will concentrate on the development of a prototype to demonstrate the feasibility of this new specification language.

Cross, James H., II↗

High frequency, high temperature specific core loss and dynamic B-H hysteresis loop characteristics of soft magnetic alloys

Limited experimental data exists for the specific core loss and dynamic B-H loops for soft magnetic materials for the combined conditions of high frequency and high temperature. This experimental study investigates the specific core loss and dynamic B-H loop characteristics of Supermalloy and Metglas 2605SC over the frequency range of 1 to 50 kHz and temperature range of 23 to 300 C under sinusoidal voltage excitation. The experimental setup used to conduct the investigation is described. The effects of the maximum magnetic flux density, frequency, and temperature on the specific core loss and on the size and shape of the B-H loops are examined.

Wieserman, W. R.↗