Results for “SIDE EFFECTS” — Page 51

NASA NTRS1992

On the coupling between a supersonic boundary layer and a flexible surface

The coupling between a two-dimensional, supersonic, laminar boundary layer and a flexible surface is studied using direct numerical computations of the Navier-Stokes equations coupled with the plate equation. The flexible surface is forced to vibrate by plane acoustic waves at normal incidence emanated by a sound source located on the side of the flexible surface opposite to the boundary layer. The effect of the source excitation frequency on the surface vibration and boundary layer stability is analyzed. We find that, for frequencies near the fifth natural frequency of the surface or lower, large disturbances are introduced in the boundary layer which may alter its stability characteristics. The interaction between a stable two-dimensional disturbance of Tollmien-Schlichting (TS) type with the vibrating surface is also studied. We find that the disturbance level is higher over the vrating flexible surface than that obtained when the surface is rig id, which indicates a strong coupling between flow and structure. However, in the absence of the sound source the disturbance level over the rigid and flexible surfaces are identical. This result is due to the high frequency of the TS disturbance which does not couple with the flexible surface.

Frendi, Abdelkader↗

NASA NTRS1958

A Method for the Calculation of the Lateral Response of Airplanes to Random Turbulence

In this method, the gust velocities are represented as rolling gusts, yawing gusts, and side gusts. Random distributions of gust velocities across the span are taken into account in defining the rolling and yawing gusts. Complex stability derivatives are used to account for the random distribution of side gusts along the fuselage and vertical tail and the lag effects in gust penetration. A sample calculation procedure is presented for obtaining the response of the airplane in each degree of freedom.

LOADS, GUST - WINGS↗

NASA NTRS1993

Aerodynamic control of NASP-type vehicles through vortex manipulation. Volume 3: Wing rock experiments

Free-to-roll tests were conducted in water and wind tunnels in an effort to investigate the mechanisms of wing rock on a NASP-type vehicle. The configuration tested consisted of a highly-slender forebody and a 78 deg swept delta wing. In the water tunnel test, extensive flow visualization was performed and roll angle histories were obtained. In the wind tunnel test, the roll angle, forces and moments, and limited forebody and wing surface pressures were measured during the wing rock motion. A limit cycle oscillation was observed for angles of attack between 22 deg and 30 deg. In general, the experiments confirmed that the main flow phenomena responsible for the wing-body-tail wing rock are the interactions between the forebody and the wing vortices. The variation of roll acceleration (determined from the second derivative of the roll angle time history) with roll angle clearly slowed the energy balance necessary to sustain the limit cycle oscillation. Different means of suppressing wing rock by controlling the forebody vortices using small blowing jets were also explored. Steady blowing was found to be capable of suppressing wing rock, but significant vortex asymmetrices are created, causing the model to stop at a non-zero roll angle. On the other hand, alternating pulsed blowing on the left and right sides of the fore body was demonstrated to be a potentially effective means of suppressing wing rock and eliminating large asymmetric moments at high angles of attack.

Suarez, Carlos J.↗

NASA NTRS2004

Transition from Ignition to Flame Growth under External Radiation in Three Dimensions (TIGER-3D)

This study focuses on localized ignition by external radiant flux and subsequent flame growth over thin polymeric materials (plastic and paper) in microgravity. Two transition stages were observed. The first transition stage covers the period from the onset of ignition to the formation of stabilized flame near the ignited area. This is followed by the second transition of the flame growth stage from the initial stabilized flame to sustained fire growth away from the ignited area. For the first stage, ignition experiments of thin PMMA sheets were conducted using a CO2 laser as an external source in the 10 s drop tower. The results of front side surface ignition and of backside surface ignition were observed. The effects of imposed flow velocity, sample thickness, and ambient oxygen concentration on ignition are obtained. Numerical study was conducted to investigate to understand and predict ignition behavior observed in the experiments. For the second stage, numerical study is being conducted to describe the effects of gravity on heat release rate of a PMMA sheet. The gravity level was varied from zero to normal gravity. The preliminary results show that the maximum heat release occurs at around 0.02 g.

Kashiwagi, Takashi↗

NASA NTRS2004

Transition from Ignition to Flame Growth under External Radiation in 3D

This study focuses on localized ignition by external radiant flux and subsequent flame growth over thin polymeric materials (plastic and paper) in microgravity. Two transition stages were observed. The first transition stage covers the period from the onset of ignition to the formation of stabilized flame near the ignited area. This is followed by the second transition of the flame growth stage from the initial stabilized flame to sustained fire growth away from the ignited area. For the first stage, ignition experiments of thin PMMA sheets were conducted using a CO2 laser as an external source in the 10 s drop tower. The results of front side surface ignition and of backside surface ignition were observed. The effects of imposed flow velocity, sample thickness, and ambient oxygen concentration on ignition are obtained. Numerical study was conducted to investigate to understand and predict ignition behavior observed in the experiments. For the second stage, numerical study is being conducted to describe the effects of gravity on heat release rate of a PMMA sheet. The gravity level was varied from zero to normal gravity. The preliminary results show that the maximum heat release occurs at around 0.02 g.

Kashiwagi, Takashi↗

NASA NTRS1992

Aerothermoelastic Analysis of a NASP-Like Vertical Fin

Several aeroelastic stability analyses for a vertical fin similar to that of the National Aero-Space Plane are described. The objectives of the study were to design and obtain an experimental data base for a supersonic wind-tunnel model of the fin in order to examine the effects of thermal loading on the flutter characteristics. This paper describes the preliminary efforts to design the wind-tunnel model, including several of the geometric parameter variations that were analyzed. The dominant flutter mechanism involved a flap vibration mode and a fin bending mode. Variation of the thicknesses of flap and root flexures, used to attach the flap to the fin, and the fin to a support, significantly affected the flutter boundary. Uniform thermal loads, affecting only material properties, had little effect, as did the application of different uniform temperatures to each side of the fin. In contrast, the application of significant chord-wise thermal gradients induced stresses which reduced the flutter dynamic pressure by as much as 37 percent. For less extreme distributed loading, the low-aspect ratio fin was relatively unaffected.

Rodgers, John P.↗

NASA NTRS2006

Optimization of Single-Sided Charge-Sharing Strip Detectors

Simulation of the charge sharing properties of single-sided CZT strip detectors with small anode pads are presented. The effect of initial event size, carrier repulsion, diffusion, drift, trapping and detrapping are considered. These simulations indicate that such a detector with a 150 m pitch will provide good charge sharing between neighboring pads. This is supported by a comparison of simulations and measurements for a similar detector with a coarser pitch of 225 m that could not provide sufficient sharing. The performance of such a detector used as a gamma-ray imager is discussed.

Hamel, L.A.↗

NASA NTRS2009

Functionalizing CNTs for Making Epoxy/CNT Composites

Functionalization of carbon nanotubes (CNTs) with linear molecular side chains of polyphenylene ether (PPE) has been shown to be effective in solubilizing the CNTs in the solvent components of solutions that are cast to make epoxy/CNT composite films. (In the absence of solubilization, the CNTs tend to clump together instead of becoming dispersed in solution as needed to impart, to the films, the desired CNT properties of electrical conductivity and mechanical strength.) Because the PPE functionalizes the CNTs in a noncovalent manner, the functionalization does not damage the CNTs. The functionalization can also be exploited to improve the interactions between CNTs and epoxy matrices to enhance the properties of the resulting composite films. In addition to the CNTs, solvent, epoxy resin, epoxy hardener, and PPE, a properly formulated solution also includes a small amount of polycarbonate, which serves to fill voids that, if allowed to remain, would degrade the performance of the film. To form the film, the solution is drop-cast or spin-cast, then the solvent is allowed to evaporate.

Chen, Jian↗

NASA NTRS2010

MISSE 6 Polymer Film Tensile Experiment

The Polymer Film Tensile Experiment (PFTE) was flown as part of Materials International Space Station Experiment 6 (MISSE 6). The purpose of the experiment was to expose a variety of polymer films to the low Earth orbital environment under both relaxed and tension conditions. The polymers selected are those commonly used for spacecraft thermal control and those under consideration for use in spacecraft applications such as sunshields, solar sails, and inflatable and deployable structures. The dog-bone shaped samples of polymers that were flown were exposed on both the side of the MISSE 6 Passive Experiment Container (PEC) that was facing into the ram direction (receiving atomic oxygen, ultraviolet (UV) radiation, ionizing radiation, and thermal cycling) and the wake facing side (which was supposed to have experienced predominantly the same environmental effects except for atomic oxygen which was present due to reorientation of the International Space Station). A few of the tensile samples were coated with vapor deposited aluminum on the back and wired to determine the point in the flight when the tensile sample broke as recorded by a change in voltage that was stored on battery powered data loggers for post flight retrieval and analysis. The data returned on the data loggers was not usable. However, post retrieval observation and analysis of the samples was performed. This paper describes the preliminary analysis and observations of the polymers exposed on the MISSE 6 PFTE.

Miller, Sharon K. R.↗

NASA NTRS2018

Scattering and Extinction by Spherical Particles Immersed in an Absorbing Host Medium

Many applications of electromagnetic scattering involve particles immersed in an absorbing rather than lossless medium, thereby making the conventional scattering theory potentially inapplicable. To analyze this issue quantitatively, we employ the FORTRAN program developed recently on the basis of the first-principles electromagnetic theory to study far-field scattering by spherical particles embedded in an absorbing infinite host medium. We further examine the phenomenon of negative extinction identified recently for monodisperse spheres and uncover additional evidence in favor of its interference origin. We identify the main effects of increasing the width of the size distribution on the ensemble-averaged extinction efficiency factor and show that negative extinction can be eradicated by averaging over a very narrow size distribution. We also analyze, for the first time, the effects of absorption inside the host medium and ensemble averaging on the phase function and other elements of the Stokes scattering matrix. It is shown in particular that increasing absorption significantly suppresses the interference structure and can result in a dramatic expansion of the areas of positive polarization. Furthermore, the phase functions computed for larger effective size parameters can develop a very deep minimum at side-scattering angles bracketed by a strong diffraction peak in the forward direction and a pronounced backscattering maximum.

Far-field electromagnetic scattering; Absorbing ho↗

NASA NTRS2018

Azimuthal Variation of Instabilities Generated on a Flared Cone by Laser Perturbations

To study the azimuthal development of boundary-layer instabilities, a controlled, laser-generated perturbation was created in the freestream of the Boeing/U.S. Air Force Office of Scientific Research Mach 6 Quiet Tunnel. The freestream perturbation convected downstream in the wind tunnel to interact with a flared-cone model. The flared cone is a body of revolution bounded by a circular arc with a 3 m radius. Pressure transducers were used to measure a wave packet generated in the cone boundary layer by the freestream perturbation. Nine of these sensors formed three stations of azimuthal arrays and were used to determine the azimuthal variation of the wave packets in the boundary layer. The freestream laser-generated perturbation was positioned upstream of the model in three different configurations: along the centerline axis, offset from the centerline axis by 1.5 mm, and offset from the centerline axis by 3.0 mm. When the freestream perturbation was offset from the centerline of a flared cone with a 1.0 mm nose radius, a larger wave packet was generated on the side toward which the perturbation was offset. As a result, transition occurred earlier on that side. The offset perturbation did not have as large of an effect on the boundary layer of a nominally sharp flared cone.

Chou, Amanda↗

NASA NTRS2021

Hypersonic Boundary-Layer Transition on Blunted Cones at Angle of Attack

Experimental studies of cones at several high-speed facilities have demonstrated that, for small nosetip bluntness, transition onset over a circular cone moves upstream along the leeward side and downstream along the windward side, but this trend may be reversed at large bluntness values, where transition onset moves downstream along the leeward side and upstream along the windward side. A theoretical and numerical investigation is performed to characterize the effects of nose bluntness on disturbance amplification over the circular cone for several angles of attack, with the goal of understanding the potential physical mechanisms behind the experimental observations. The three-dimensional laminar basic states over a 1.5 m long, 7-degree half-angle cone with 9.525 mm nosetip radius are computed for selected angles of attack values and freestream conditions that are selected to match the Mach 10 experiments conducted within the Hypervelocity Wind Tunnel 9 at the Arnold Engineering Development Complex (AEDC). The solutions at a freestream unit Reynolds number of 17.1 million per meter are used to perform detailed instability analyses for angles of attack equal to 0, 1, 3, and 5 degrees. Results indicate that the linear amplification of stationary crossflow waves along inflection lines may begin to influence transition along the acreage of the cone for angles of attack equal to or larger than 5 degrees. The measured trend in transition front with respect to increasing angle of attack is found to be consistent with the predicted increase in the amplification factors for Mack mode disturbances along the streamline trajectories. The increase in Mack mode amplification along the windward ray for higher angles of attack is shown to be the result of a progressively earlier entropy-layer swallowing. Computations also indicate that the transition amplification factor along the windward ray is not constant and increases with the angle of attack and that the transition #-factors along the leeward ray are rather small. The nonmodal analysis for zero degrees angle of attack shows that entropy-layer disturbances with appreciably strong energy growth can coexist with Mack mode instabilities at the measured transition location.

boundary layer transition↗

NASA NTRS2021

Hypersonic Boundary-Layer Transition on Blunted Cones at Angle of Attack

Experimental studies of cones at several high-speed facilities have demonstrated that, for small nosetip bluntness, transition onset over a circular cone moves upstream along the leeward side and downstream along the windward side, but this trend may be reversed at large bluntness values, where transition onset moves downstream along the leeward side and upstream along the windward side. A theoretical and numerical investigation is performed to characterize the effects of nose bluntness on disturbance amplification over the circular cone for several angles of attack, with the goal of understanding the potential physical mechanisms behind the experimental observations. The three-dimensional laminar basic states over a 1.5 m long, 7-degree half-angle cone with 9.525 mm nosetip radius are computed for selected angles of attack values and freestream conditions that are selected to match the Mach 10 experiments conducted within the Hypervelocity Wind Tunnel 9 at the Arnold Engineering Development Complex (AEDC). The solutions at a freestream unit Reynolds number of 17.1 million per meter are used to perform detailed instability analyses for angles of attack equal to 0, 1, 3, and 5 degrees. Results indicate that the linear amplification of stationary crossflow waves along inflection lines may begin to influence transition along the acreage of the cone for angles of attack equal to or larger than 5 degrees. The measured trend in transition front with respect to increasing angle of attack is found to be consistent with the predicted increase in the amplification factors for Mack mode disturbances along the streamline trajectories. The increase in Mack mode amplification along the windward ray for higher angles of attack is shown to be the result of a progressively earlier entropy-layer swallowing. Computations also indicate that the transition amplification factor along the windward ray is not constant and increases with the angle of attack and that the transition #-factors along the leeward ray are rather small. The nonmodal analysis for zero degrees angle of attack shows that entropy-layer disturbances with appreciably strong energy growth can coexist with Mack mode instabilities at the measured transition location.

Boundary Layer Transition↗

DOE OSTI2021

Method for direct conversion of carbon dioxide to dialkyl carbonates using ethylene oxide as feedstock

A method for co-production of high purity dimethyl carbonate and mono-ethylene glycol by applying a reactor, such as a membrane reactor and/or an adsorbent-catalytic reactor by capturing and reacting carbon dioxide with methanol and ethylene oxide. Carbon dioxide may be recovered from primary sources (utilities and industrial processes) by a membrane or solid adsorbent, and subsequently converted to an intermediate hydroxy-ethyl-methyl carbonate by reacting with ethylene oxide and methanol. For high-purity carbon dioxide (obtained by carbon capture technologies or from an ethanol fermentation process), the membrane reactor is replaced with a catalytic reactor for direct conversion of carbon dioxide to hydroxy-ethyl-methyl carbonate by reacting with ethylene oxide and methanol. The hydro-ethyl-methyl carbonate is further reacted with methanol for conversion to dimethyl carbonate. A combination of heterogeneous and homogeneous catalysts is implemented for an effective conversion of carbon dioxide. An integrated reactive distillation process using side reactors is used for facilitating catalytic reaction for production of high purity dimethyl carbonate.

Panchal, Chandrakant B.↗

DOE OSTI2026

Secondary-Side Active Rectifier Synchronization and Control in LCC-LC Compensated Inductive Power Transfer Systems

This paper proposes a communication-less synchronization and output power control strategy for LCC-LC compensated inductive power transfer systems with a secondaryside active rectifier. By replacing the passive rectifier with an active bridge, the proposed architecture eliminates the need for a separate secondary-side DC-DC converter and enables direct regulation of battery power. The key challenge in such a system is achieving robust synchronization of the secondary active bridge with the primary inverter without access to primary-side signals. To address this issue, the secondary-side variables are analyzed and the current through the secondary series inductor is identified as a load-independent synchronization variable with a fixed phase relationship to the primary excitation. A fixed-frequency second order generalized (SOGI)-based phase locked loop (PLL) is used to estimate the switching phase and frequency, and a phase-shift-based output power controller is developed using a phasor-transformer model of the active bridges. A modified control formulation is further introduced to remove phase-dependent loop-gain variation and simplify controller design. Simulation results validate the proposed method under both fixed and varying switching-frequency conditions, demonstrating successful frequency tracking from 82 kHz to 88 kHz and accurate output power regulation over a wide operating range. The proposed method offers a compact and effective solution for high-power IPT systems by enabling secondary-side synchronization and control without wireless communication or an additional DC-DC conversion stage.

Fernandes, Arnold Anthony [ORNL] (ORCID:0009000631↗

NASA NTRS1978

Effect of facility background gases on internal erosion of the 30-cm Hg ion thruster

Sputtering erosion of the upstream side of the molybdenum screen grid by discharge chamber ions in mercury bombardment thrusters was considered. Data which revealed that the screen grid erosion was very sensitive to the partial pressure of certain background gases in the space simulation vacuum facility were presented along with results of tests conducted to evaluate this effect. It is shown from estimates of the screen grid erosion in space that adequate lifetime for proposed missions exists.

Rawlin, V. K.↗

DOE OSTI2024

How hydrophobicity, side chains, and salt affect the dimensions of disordered proteins

Abstract Despite the generally accepted role of the hydrophobic effect as the driving force for folding, many intrinsically disordered proteins (IDPs), including those with hydrophobic content typical of foldable proteins, behave nearly as self‐avoiding random walks (SARWs) under physiological conditions. Here, we tested how temperature and ionic conditions influence the dimensions of the N‐terminal domain of pertactin (PNt), an IDP with an amino acid composition typical of folded proteins. While PNt contracts somewhat with temperature, it nevertheless remains expanded over 10–58°C, with a Flory exponent, ν , >0.50. Both low and high ionic strength also produce contraction in PNt, but this contraction is mitigated by reducing charge segregation. With 46% glycine and low hydrophobicity, the reduced form of snow flea anti‐freeze protein (red‐sfAFP) is unaffected by temperature and ionic strength and persists as a near‐SARW, ν ~ 0.54, arguing that the thermal contraction of PNt is due to stronger interactions between hydrophobic side chains. Additionally, red‐sfAFP is a proxy for the polypeptide backbone, which has been thought to collapse in water. Increasing the glycine segregation in red‐sfAFP had minimal effect on ν . Water remained a good solvent even with 21 consecutive glycine residues ( ν > 0.5), and red‐sfAFP variants lacked stable backbone hydrogen bonds according to hydrogen exchange. Similarly, changing glycine segregation has little impact on ν in other glycine‐rich proteins. These findings underscore the generality that many disordered states can be expanded and unstructured, and that the hydrophobic effect alone is insufficient to drive significant chain collapse for typical protein sequences.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS1983

Numerical modeling of turbulent flow in a channel

Two-dimensional incompressible turbulent flow in a channel with a backward-facing step was studied numerically by Chorin's Random Vortex Method (RVM), an algorithm capable of tracing the action of elementary turbulent eddies and their cumulative effects without imposing any restrictions upon their motions. The step occurs in one side of a channel with otherwise flat, parallel walls; its height equals 1/3, 1/4 or 1/5 the width of the channel downstream. The main objective was to investigate the behavior of the large-scale turbulent eddies in a flow and the flow characteristics in the separated shear layer, the reattached zone, and the rebuilding boundary layer after reattachment. The unsteady vorticity field and the distribution of time-averaged turbulent statistics were obtained. The effects of expansion step height and initial boundary layer state were also studied. Comparisons were made with the available experimental results. The agreement is satisfactory in the velocity profiles and in the reattachment length, and fairly good in the turbulence profiles. Also a mechanism of the development of the reattaching turbulent flow was suggested by the numerical results.

Dai, Y. W.↗