SEARCH · Engineering Papers

Results for “Plating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

All sources NASA NTRS DOE OSTI

NASA NTRS1959

Theoretical Determination of Lifetime of Compressed Plates at Elevated Temperatures

A method for the theoretical determination of the lifetime of com- pressed plates at elevated temperatures is presented. In this approach, linearized equations are used throughout with the assumption that the plate material is a standard linear solid. The critical time (lifetime) is determined by reducing the time-dependent behavior to the time- independent response of purely elastic buckling. Theoretically predicted lifetimes of 2024-T3 (formerly 24S-T3) aluminum-alloy plates at 450 F are compared with experimental values obtained in previous work.

Herrmann, George↗

NASA NTRS1959

Effect of Six Missile-Bay Baffle Configurations and a Rocket End Plate on Ejection Releases of an MB-1 Rocket from a 0.05 Scale Model of the Convair F-106A Airplane

As a continuation of an investigation of the release characteristics of an MB-1 rocket carried internally by the Convair F-106A airplane, six missile-bay baffle configurations and a rocket end plate have been investigated in the 27- by 27-inch preflight jet of the NASA Wallops Station. The MB-1 rocket used had retractable fins and was ejected from a missile bay modified by the addition of six different baffle configurations. For some tests a rocket end plate was added to the model. Dynamically scaled models (0.04956 scale) were tested at a simulated altitude of 22,450 feet and Mach numbers of 0.86, 1.59, and 1.98, and at a simulated altitude of 29,450 feet and a Mach number of 1.98. The results of this investigation indicate that the missile-bay baffle configurations and the rocket end plate may be used to reduce the positive pitch amplitude of the MB-1 rocket after release. The initial negative pitching velocity applied to the MB-1 rocket might then be reduced in order to maintain a near-level-flight attitude after release. As the fuselage angle of attack is increased, the negative pitch amplitude of the rocket is decreased.

Hinson, William F.↗

NASA NTRS1959

An Experimental Study at a Mach Number of 3 of the Effect of Turbulence Level and Sandpaper Type Roughness on Transition on a Flat Plate

An investigation has been conducted at a Mach number of 3 of the effect of turbulence level and sandpaper-type roughness on transition for a flat plate. The Reynolds number varied from 0.8 x 10(exp 6) to 1.8 x 10(exp 6) per inch; the settling-chamber turbulence level varied from 0.7 percent to 35 percent; and the heat transfer between the plate and the stream was negligible. Transition locations were determined by an optical method. This method was indicative of a permanent change in the boundary-layer density distribution rather than the onset of turbulent bursts. Results showed that, when transition was influenced by roughness, it moved in a way similar to its movement on a smooth plate. That is, it gradually approached the roughness location with either an increase in unit Reynolds number or an increase in turbulence level. For roughness submerged in the linear portion of the boundary-layer velocity profile, the square root of the roughness Reynolds number and the ratio of roughness height to boundary-layer displacement thickness gave similar results as parameters for predicting the effects of roughness. A range of each of these parameters which moved transition less than 10 percent was found and this range was a function of turbulence level.

Jones, Robert A.↗

NASA NTRS1998

Influence of Impactor Mass on the Damage Characteristics and Failure Strength of Laminated Composite Plates

The results of an experimental study of the effect of impactor mass on the low-speed impact response of laminated flat composite plates is presented. Dropped weight impact response, damage characteristics, and residual strengths of quasi-isotropic flat plates are presented for a range of energy levels by systematically varying the mass of the impactor. Measured contact forces and damage areas are also presented. The results indicate that the contact force and damage area are nonlinear functions of the impactor mass and vary considerably over the entire range of energy levels considered. The different damage levels induced in a plate specimen when impacted at a given energy level with impactors of different masses significantly influence its compressive residual strength. The results provide clear and consistent trends in contact force, damage area, and compression-after-impact strength when the data are expressed as a function of the impactor momentum.

Ambur, Damodar R.↗

NASA NTRS1994

Equivalent Plate Structural Modeling for Wing Shape Optimization Including Transverse Shear

A new technique for structural modeling of airplane wings is presented taking transverse shear effects into account. The kinematic assumptions of first-order shear deformation plate theory In combination with numerical analysis, where simple polynomials are used to define geometry, construction, and displacement approximations, lead to analytical expressions for elements of the stiffness and mass matrices and load vector. Contributions from the cover skins, spar and rib caps, and spar and rib webs are included as well as concentrated springs and concentrated masses. Limitations of wing modeling techniques based on classical plate theory are discussed, and the Improved accuracy of the new equivalent plate technique is demonstrated through comparison with finite element analysis and test results. Expressions for analytical derivatives of stiffness, mass, and load terms with respect to wing shape are given. Based on these, it is possible to obtain analytic sensitivities of displacements, stresses, and natural frequencies with respect to planform shape and depth distribution. This makes the new capability an effective structural tool for wing shape optimization.

Livne, Eli↗

NASA NTRS1997

Elastic Buckling of Orthotropic Plates Under Varying Axial Stresses

The elastic buckling load of simply supported rectangular orthotropic plates subjected to a second degree parabolic variation of axial stresses in the longitudinal direction is calculated using analytical methods. The variation of axial stresses is equilibrated by nonuniform shear stresses along the plate edges and transverse normal stresses. The influence of the aspect ratio is examined, and the results are compared with plates subjected to uniform axial stresses.

Badir, Ashraf↗

NASA NTRS1998

Evaluation of Transverse Thermal Stresses in Composite Plates Based on First-Order Shear Deformation Theory

A postprocessing procedure is presented for the evaluation of the transverse thermal stresses in laminated plates. The analytical formulation is based on the first-order shear deformation theory and the plate is discretized by using a single-field displacement finite element model. The procedure is based on neglecting the derivatives of the in-plane forces and the twisting moments, as well as the mixed derivatives of the bending moments, with respect to the in-plane coordinates. The calculated transverse shear stiffnesses reflect the actual stacking sequence of the composite plate. The distributions of the transverse stresses through-the-thickness are evaluated by using only the transverse shear forces and the thermal effects resulting from the finite element analysis. The procedure is implemented into a postprocessing routine which can be easily incorporated into existing commercial finite element codes. Numerical results are presented for four- and ten-layer cross-ply laminates subjected to mechanical and thermal loads.

Rolfes, R.↗

NASA NTRS2001

Damage Progression in Buckle-Resistant Notched Composite Plates Loaded in Uniaxial Compression

Results of an experimental and analytical evaluation of damage progression in three stitched composite plates containing an angled central notch and subjected to compression loading are presented. Parametric studies were conducted systematically to identify the relative effects of the material strength parameters on damage initiation and growth. Comparisons with experiments were conducted to determine the appropriate in situ values of strengths for progressive failure analysis. These parametric studies indicated that the in situ value of the fiber buckling strength is the most important parameter in the prediction of damage initiation and growth in these notched composite plates. Analyses of the damage progression in the notched, compression-loaded plates were conducted using in situ material strengths. Comparisons of results obtained from these analyses with experimental results for displacements and axial strains show good agreement.

McGowan, David M.↗

NASA NTRS2001

Parametric Fin-Body and Fin-Plate Database for a Series of 12 Missile Fins

A cooperative experimental investigation has been performed to obtain a systematic fin-body and fin-plate database for a series of 12 missile fins. These data are intended to complement and extend the information contained in the Triservice missile project and to provide a systematic set of experimental data from which fin-body interference factors can be derived. Data were obtained with the fins mounted on both an axisymmetric body and on a flat plate that was used to simulate fin-alone measurements. The experiments were conducted at Mach numbers from 0.60 to 3.95; fin deflection angles of 0 deg, 10 deg, and -10 deg; and angles of attack up to 30 deg on the body and up to 95 deg on the flat plate. The data were obtained from three-component balances attached to the fins and a six-component balance located in the axisymmetric body. The data obtained in this project are documented in tabular form in this report. In addition, selected data are presented in graphical form to illustrate the effects of the test variables. These variables are configuration angle of attack; Mach number; and fin parameters of deflection angle, planform size, taper ratio, and aspect ratio. A very limited comparison with the Triservice missile data is made to illustrate the consistency between the data from these two projects.

Allen, Jerry M.↗

NASA NTRS2001

Experimental Structural Dynamic Response of Plate Specimens Due to Sonic Loads in a Progressive Wave Tube

The objective of the current study was to assess the repeatability of experiments at NASA Langley's Thermal Acoustic Fatigue Apparatus (TAFA) facility and to use these experiments to validate numerical models. Experiments show that power spectral density (PSD) curves were repeatable except at the resonant frequencies, which tended to vary between 5 Hz to 15 Hz. Results show that the thinner specimen had more variability in the resonant frequency location than the thicker sample, especially for modes higher than the first mode in the frequency range. Root Mean Square (RMS) tended to be more repeatable. The RMS behaved linearly through the SPL range of 135 to 153 dB. Standard Deviations (STDs) of the results tended to be relatively low constant up to about 147 dB. The RMS results were more repeatable than the PDS results. The STD results were less than 10% of the RMS results for both the 0.125 in (0.318 cm) and 0.062 in (0.1588 cm) thick plate. The STD of the PSD results were around 20% to 100% of the mean PSD results for non-resonant and resonant frequencies, respectively, for the 0.125 in (0.318 cm) thicker plate and between 25% to 125% of the mean PSD results, for nonresonant and resonant frequencies, respectively, for the thinner plate.

Betts, Juan F.↗

NASA NTRS2002

A Cryogenic Half-Wave Plate Module to Measure Polarization at Multiple FIR Passbands

One of the key components in a far-infrared polarimeter that is being designed at the University of Chicago is a locally-powered half-wave plate module. This compact, lightweight, and reliable module will operate at cryogenic temperatures, rotating a half-wave plate about its axis within the optical path. By doing so, polarization measurements can be made. Further, by utilizing multiple half-wave plate modules within the polarimeter, multiple wavelengths or passbands can be studied. In this paper, we describe the design and performance of a relatively inexpensive prototype module that was assembled and tested successfully, outline the difficulties that had to be overcome, and recommend improvements to future modules. This effort now lays some of the groundwork for a next-generation polarimeter for far-infrared astronomy.

Rennick, Timothy S.↗

NASA NTRS2003

Using Plate Finite Elements for Modeling Fillets in Design, Optimization, and Dynamic Analysis

A methodology has been developed that allows the use of plate elements instead of numerically inefficient solid elements for modeling structures with 90 degree fillets. The technique uses plate bridges with pseudo Young's modulus (Eb) and thickness (tb) values placed between the tangent points of the fillets. These parameters are obtained by solving two nonlinear simultaneous equations in terms of the independent variables rlt and twallt. These equations are generated by equating the rotation at the tangent point of a bridge system with that of a fillet, where both rotations are derived using beam theory. Accurate surface fits of the solutions are also presented to provide the user with closed-form equations for the parameters. The methodology was verified on the subcomponent level and with a representative filleted structure, where the technique yielded a plate model exhibiting a level of accuracy better than or equal to a high-fidelity solid model and with a 90-percent reduction in the number of DOFs. The application of this method for parametric design studies, optimization, and dynamic analysis should prove extremely beneficial for the finite element practitioner. Although the method does not attempt to produce accurate stresses in the filleted region, it can also be used to obtain stresses elsewhere in the structure for preliminary analysis. A future avenue of study is to extend the theory developed here to other fillet geometries, including fillet angles other than 90 and multifaceted intersections.

Brown, A. M.↗

NASA NTRS1961

Optimum Design of Insulated Compression Plates Subjected to Aerodynamic Heating

A method to determine the optimum thicknesses of insulation and load-carrying structure has been applied to insulated compression plates subjected to aerodynamic heating. The optimum design results in the lowest combined weight of insulation and load-carrying plate. Load parameters which included the imposed load, insulation conductivity and density, and flight time were found for design strength criteria of compressive yield, compressive buckling, and postbuckling failure. Charts of optimum total weight were prepared for 2024-T3 aluminum alloy, HK3lA magnesium alloy, 17-7 PH stainless steel, and Inconel X for each design criterion. The results show that 17-7 PH stainless steel and Inconel X are most efficient for compressive yield stress and that HK3lA magnesium is most efficient for buckling. HK31A magnesium is also most efficient for the postbuckling failure criterion except under conditions of light loading and long flight periods; under such conditions uninsulated Inconel X may be superior for environmental temperature less than 1,200 F. Insulated magnesium is more efficient than insulated aluminum because the lower density of magnesium permits the use of thick plates with large heat capacity. When more than one failure mode was applied to a design, it was found that the minimum weight structure was one in which all modes of failure occurred at the design load.

Davidson, John R.↗

NASA NTRS2000

Three-Dimensional Effects in the Plate Element Analysis of Stitched Textile Composites

Three-dimensional effects related to the analysis of stitched textile composites are discussed. The method of calculation is based on the virtual crack closure technique (VCCT), and models that model the upper and lower surface of the delamination or debond with two-dimensional (2D) plate elements rather than three-dimensional (3D) solid elements. The major advantages of the plate element modeling technique are a smaller model size and simpler geometric modeling. Details of the modeling of the laminated plate and the stitching are discussed.

Glaessgen, E. H.↗

NASA NTRS1996

Touch-plate and statolith formation in graviceptors of ephyrae which developed while weightless in space

Ultrastructural studies of the statocysts and touch-plates of graviceptors (rhopalia) of Aurelia ephyrae revealed that (1) touch-plate hair cells are present; and (2) cytoplasmic strands from the hair cell bases extend from the neurite plexus to touch similar strands from the lithocytes. This close association of hair cell neurites and statocysts may have important implications regarding the transmitting and processing of positional information with respect to the gravity vector. Graviceptors of ephyrae which developed while weightless in microgravity were compared with controls at the ultrastructural level. We found that hair cells of ephyrae which developed in microgravity had fewer lipid droplets in the large spaces near their bases as compared with 1 g controls. In the ephyrae from the first microgravity experiment, hair cells had more large apical vacuoles with filamentous content than were found in hair cells of ephyrae from the second experiment and controls. The neurite plexus and the network of cytoplasmic strands extending to the statocysts were not different in microgravity-developed ephyrae from controls. Behavioral differences in swimming and orienting in ephyrae in microgravity and controls (reported earlier) were not explained by morphological differences in the hair cells of the touch-plates or the statocysts, although functional differences apparently occurred.

NASA Discipline Developmental Biology↗

NASA NTRS1990

Histomorphometric and electron microscopic analyses of tibial epiphyseal plates from Cosmos 1887 rats

Previous studies have shown that the changes seen in the bones of growing rats exposed to microgravity are due in part to changes that occur in the growth plate during spaceflight. In this study, growth plates of rats flown aboard Cosmos 1887 (12.5-day flight plus 53.5-h recovery at 1 g) were analyzed using light and electron microscopy and computerized planimetry. The proliferative zone of flight animals was found to be significantly (P less than or equal to 0.01) larger than that of controls, while the reserve and hypertrophic/calcification zones were significantly reduced. Flight animals also had more cells per column in the proliferative zone than did controls and less in the hypertrophic/calcification region. The total number of cells, however, was significantly greater in flight animals. No difference was found in perimeter or in shape factor, but area was significantly less in flight animals. Electron microscopy showed that collagen fibrils in flight animals were wider than in controls. Since the time required for a cell to cycle through the growth plate is 2-3 days at 1 g, the results reported here represent both the effects of exposure to microgravity and the initial stages of recovery from that exposure.

Non-NASA Center↗

NASA NTRS2005

Drag Measurements of Porous Plate Acoustic Liners

This paper presents the results of direct drag measurements on a variety of porous plate acoustic liners. The existing literature describes numerous studies of drag on porous walls with injection or suction, but relatively few of drag on porous plates with neither injection nor suction. Furthermore, the porosity of the porous plate in existing studies is much lower than typically used in acoustic liners. In the present work, the acoustic liners consisted of a perforated face sheet covering a bulk acoustic absorber material. Factors that were varied in the experiment were hole diameter, hole pattern, face sheet thickness, bulk material type, and size of the gap (if any) between the face sheet and the absorber material.

Wolter, John D.↗

NASA NTRS2006

Rapid Fabrication of Flat Plate Cavity Phosphor Thermography Test Models for Shuttle Return-to-Flight Aero-Heating

Methods, materials and equipment are documented for fabricating flat plate test models at NASA Langley Research Center for Shuttle return-to-flight aeroheating experiments simulating open and closed cavity interactions in Langley s hypersonic 20-Inch Mach 6 air wind tunnel. Approximately 96 silica ceramic flat plate cavity phosphor thermography test models have been fabricated using these methods. On one model, an additional slot is machined through the back of the plate and into the cavity and vented into an evacuated plenum chamber to simulate a further opening in the cavity. After sintering ceramic to 2150 F, and mounting support hardware, a ceramic-based two-color thermographic phosphor coating is applied for global temperature and heat transfer measurements, with fiducial markings for image registration.

Buck, Gregory M.↗