Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Microstructure and electrical properties of Na{sub 0.5}Bi{sub 0.5}(Ti{sub 0.98}Zr{sub 0.02})O{sub 3} thin film deposited on indium tin oxide/glass substrate

Highlights: • NBTZr deposited on ITO/glass under O{sub 2} exhibits a phase-pure perovskite structure. • NBTZr shows a well-defined P–E with a remanent polarization of 11.5 μC/cm{sup 2}. • At 100 kHz and 14 V, the dielectric tunability is 44.97% and FOM is 3.58. • At 100 kHz, the ϵ{sub r} and tanδ are 205 and 0.092, respectively. - Abstract: Na{sub 0.5}Bi{sub 0.5}(Ti{sub 0.98}Zr{sub 0.02})O{sub 3} (NBTZr) thin film has been prepared by chemical solution deposition onto indium tin oxide (ITO)/glass under O{sub 2} atmosphere. The microstructure and related electrical performance are investigated. The film exhibits a phase-pure polycrystalline perovskite structure, with evenly distributed grain size and full compactness. A well-defined polarization-electric field (P–E) loop can be observed with a remanent polarization (P{sub r}) of 11.5 μC/cm{sup 2} and small gap. At 14 V and 100 kHz, the dielectric tunability as high as 44.97% can be achieved and the dielectric constant of 205, dissipation factor of 0.092 as well as figure of merit of 3.58 are obtained.

36 MATERIALS SCIENCE↗

Evaluation of the microstructure and mechanical properties of WC particle reinforced aluminum matrix composites fabricated by friction stir processing

Highlights: • FSP was used for the preparation of aluminum matrix composites reinforced with WC particle. • WC particles were uniformly distributed in the composite. • WC particles refined the grains of aluminum matrix. • WC particles enhanced the hardness and tensile strength, but decreased the ductility. - Abstract: Tungsten carbide (WC) is an attractive reinforcing material for aluminum and its alloys. However, it is technically challenging to fabricate WC particle reinforced aluminum matrix composites (AMCs) with homogeneous distribution of WC particles by liquid state processing techniques because of large density gradient. The present work aim to produce WC particle reinforced aluminum matrix composites (AMCs) through friction stir processing (FSP) and analyze the effect of its volume fraction on the microstructural features and the mechanical behavior of the developed AMCs. Microstructural evaluation was conducted on the cross-sections of the samples by optical microscopy (OM), scanning electron microscopy (SEM) and electron backscattered diffraction (EBSD). Microhardness testing was conducted across the cross-sections of FSPed samples to obtain hardness profiles and tensile test was conducted on as-received Al and FSPed samples. The fabricated AMCs exhibited the homogeneous distribution of WC particle with no obvious particle clustering in the stir zone, irrespective of position and WC particle volume fraction. Excellent WC/Al interfacial bonding was obtained in all FSPed AMCs with obviously refined grains. The average size of WC particles after FSP was slightly reduced with the increased volume fraction. It was also found that increasing the volume fraction of WC particles favored the grain refinement, improved the hardness and strength, but decreased the ductility. This improvement in the hardness and strength was attributed to the grain refinement strengthening and homogeneous distribution of WC particles. The decreased ductility resulted from the introduction of more WC particles. Increasing the volume fraction of WC particles caused the nature of fracture to move towards brittle nature.

36 MATERIALS SCIENCE↗

Effect of Tempering Mode on the Microstructure and Mechanical Properties of a Lean Alloy Martensitic Steel: Conventional Reheating Versus Induction Reheating

The present study elucidates the effect of the reheating rate and tempering temperature on the type, size, and distribution of carbides/cementite formed within martensite (M)/lower bainite (LB) during the tempering of a high-strength low-alloy (HSLA) steel. A comparison is made between conventional reheating and induction reheating. All the experimental samples were quenched from the austenitization temperature of 920 °C for 30 min. An ultra-high yield strength of 1180 MPa and a good toughness of 94 J at 0 °C were obtained after tempering at 400 °C for 15 min by induction reheating (~ 100 °C/s), while in the case of conventional reheating (~ 2 °C/s) and tempering at 400 °C for 15 min, the steel had a high strength of 1159 MPa, but a poor toughness of 47 J at 0 °C. After induction reheating to 500 °C and tempering for 15 min, a higher toughness was obtained (91 J at 0 °C), but the strength was decreased to 967 MPa. Microstructural characterization revealed that fine needle-like carbides (ε-Fe{sub 2.4}C) were obtained by induction reheating to 400 °C and tempering for 15 min. However, samples tempered at 400 °C by conventional reheating and 500 °C by induction reheating both precipitated coarse θ-Fe{sub 3}C. In the former, θ-Fe{sub 3}C precipitated at locations that were previously austenite grain boundaries and led to tempered martensite embrittlement (TME). In the latter, Ostwald ripening occurred, and the precipitates could not maintain high strength. The excellent mechanical properties of induction reheated steel (400 °C, 15 min) are attributed to the following aspects: (a) The selection of appropriate tempering temperature did not lead to decarburization and ensured high strength, and (b) a high reheating rate promoted carbide dispersion and avoided TME in steel.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of high Mn-containing ferritic-martensitic alloys exposed to cyclical thermal treatment

Substantial residual tensile stress tends to accumulate in currently available high-Cr ferritic martensitic steels that are subjected to cyclical heat treatment, which leads to premature brittle fracture. By tailoring the alloy composition, this thermal cycling can be exploited to induce a high number density of nanoprecipitates and phase transformations countering residual tensile stresses. In this work, three new variants of ferritic-martensitic steels have been designed with computational thermodynamics to meet the goals of mitigating residual tensile stresses by lowering martensite start temperatures and of enhancing mechanical strength and irradiation sink strength by increasing the number density of nanoprecipitates. Furthermore, ctenast materials were subjected to cyclical heat treatment. The thermally cycled samples were evaluated with mechanical testing and microstructural analysis to identify the optimal composition in which figures of merit include low residual stress and a high density of nanoscale MX (M = metal, X = C/N) precipitates, leading to high yield strength with reasonable ductility. The noticeably higher density of nanoprecipitates in the optimal alloy favor its higher yield strength, which is supported by the microstructure-derived yield strength calculation and precipitation kinetics simulation.

36 MATERIALS SCIENCE↗

Welded and Hydrogen Charged Zircaloy-4 and Welded Stainless Steel 347 Property Data and Microstructures for the Target Solution Vessel and Support Lines of SHINE

SHINE Medical Technologies is developing a facility that will produce molybdenum-99 for medical isotope procedures. As part of this facility, a metal tank, called the target solution vessel (TSV), will hold a uranyl sulfite solution. The TSV must withstand neutron irradiation near room temperature and potential corrosion from the aqueous solution. The large cylindrical TSV will be fabricated by welding and will have numerous pipes and connections also attached via welding. The vessel and those pipes will have varying thicknesses so both gas tungsten arc welding (GTAW) and flux-cored arc welding (FCAW) will be necessary to fabricate different sections. The original material under consideration for the TSV was Zircaloy-4 (Zry-4), but it is known to form a hydride which can degrade its mechanical properties. Thus, some investigation here is focused on the effects of hydrogen uptake in the Zry-4. Additionally, the alternative material being considered is AISI 347, a stainless steel. Both materials have little existing data for their neutron irradiation behavior below 100°C, and both have open questions on the weld behavior under neutron irradiation. Testing has focused on characterizing their weld properties with tensile tests and performing neutron irradiation of samples in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL).

07 ISOTOPE AND RADIATION SOURCES↗

Second Annual Progress Report on Correlation Between Microstructure and Mechanical Properties of Neutron-Irradiated Ferritic-Martensitic and Austenitic Steels

Ferritic-martensitic steels G92-2b (an optimized Grade 92 heat), NF616 and T91, and austenitic stainless steel 800H and its Grain Boundary Engineering (GBE)-treated version 800H-TMP (ThermoMechanical Processing) were irradiated in the High Flux Isotope Reactor (HFIR) of Oak Ridge National Laboratory (ORNL) and the Advanced Test Reactor (ATR) of Idaho National Laboratory (INL). Selected G92-2b samples were irradiated up to 14.66 dpa in the HFIR at two temperature ranges: 400–496.7°C and 683.3– 720°C. NF616 and T91 were irradiated in the ATR up to 8.16 dpa with the irradiation temperatures ranged from 241°C to 447.5°C. Alloy 800H and 800H-TMP samples were irradiated in both the HFIR and the ATR. Selected 800H and 800H-TMP samples had HFIR irradiation to 1.28 dpa at 580°C and ATR irradiation up to 9.12 dpa at 359°C to 431°C. Vickers hardness measurements, fractography, and microstructural characterization were performed on the selected samples in the Low Activation Materials Design and Analysis (LAMDA) laboratory. Radiation-hardening of G92-2b was observed at the lower doses and lower irradiation temperatures (400- 496.7°C), with GB03 (0.52 dpa at 400°C) and GB04 (7.44 dpa at ~490°C) showing ~12% and ~8% hardening, respectively. Softening by ~14% was observed for GB05 (14.66 dpa at 496.7°C). Radiationsoftening of G92-2b was more prevalent at the higher irradiation temperatures (683.3-~720°C), with GB10 (0.46 dpa at 683.3°C), GB11 (7.44 dpa at ~720°C), and GB12 (14.63 dpa at ~720°C) showing ~8%, ~8%, and ~40% softening, respectively. Radiation-hardening of NF616 and T91 was observed with the hardness increased by ~37% to ~65% depending on the irradiation doses and irradiation temperatures. Within the studied irradiation conditions of NF616 and T91, samples with a higher dose had a larger hardness after irradiation. All the tested alloy 800H and 800H-TMP samples in this work showed radiation-hardening by ~96±7% to ~152±10%. Alloy 800H-TMP tended to have slightly smaller radiation-hardening than alloy 800H. The fractography results of G92-2b sample GB03, GB10, and GB11, together with the previously characterized fractography of GB04, GB05, and GB12, indicated that the ductility of G92-2b was maintained up to 14.66 dpa at the lower irradiation temperatures of 400-496.7°C, while some loss of ductility (less necking) was observed for higher doses at the higher irradiation temperatures of 683.3-720°C. This agrees with the previously reported tensile test results of G92-2b, where the elongation of G92-2b was reduced at higher doses at the higher irradiation temperatures. Dimple sizes increased at higher doses, which are more evident at the higher irradiation temperatures of 683.3-~720°C. The fractography of NF616 sample D2 (2.96 dpa at 291.5°C), D4 (5.91 dpa at 359°C), and D6 (8.16 dpa at 431°C) indicated loss of ductility with negligible necking for sample D2, while ductile failure for samples D4 and D6. Fractography of alloy 800H and 800H-TMP samples in various irradiation conditions showed ductile failure with obvious necking. Dimples were observed, with some of them containing large Ti-rich particles, in all the 800H/800H-TMP samples. Electron backscatter diffraction characterization of GB12 indicated the recovery of the lath structure, which was generally replaced by an equiaxed grain structure. Transmission electron microscopy (TEM) characterization showed the presence of frequent M 23 C 6 (M = primarily Cr), MX (M = primarily V), spherical Nb(C,N) precipitates, and occasional Laves phase precipitates in the G92-2b samples. MX precipitates with sizes of 20-30 nm were observed at boundaries of smaller grains, indicating the pinning effect of the V-rich precipitates. The lath structure recovery was more evident at the higher irradiation temperatures (683.3-~720°C), with decreased densities of line dislocations and M23C6 precipitates. The irradiated T91 (TA04) showed the growth of M23C6 precipitates to 101 ± 40 nm from the initial 68 ± 22 nm in the unirradiated condition. Dislocation loops of both {100} and {111} types were present in TA04. TEM characterization was also performed on the irradiated 800H (N4, N5, N6, and AR2) and 800H-TMP (P4, P5, P6, and HG1). Accumulation of M 23 C 6 precipitates at grain boundaries was observed in all the xii 800H/800H-TMP samples, and the presence of Ti(C,N) precipitates at grain boundaries and in the matrix was observed in the irradiated 800H-TMP. Some Ti(C,N) precipitates are embedded in the M 23 C 6 precipitates, maintaining specific orientation relationships between the precipitates and between the precipitate and matrix. In addition, nanoscale Si-rich clusters were observed in the matrix of all the 800H/800H-TMP samples, with EDS Si maps tending to have a lower contrast in 800H-TMP samples. Atom probe tomography was conducted on the same samples, supported by a Rapid Turnaround Examination project under Nuclear Science User Facilities. The results are being analyzed to be integrated with the TEM results for a confident description of the γ’ precipitates. Dislocation loops also formed in all the 800H/800H-TMP samples. The density and the average size of dislocation loops were quantified to be in the order of 10 22 – 10 23 m -3 and 11.7 – 15.9 nm, respectively, in the ATR-irradiated 800H/800H-TMP samples. The loop densities in irradiated 800H were higher than that in irradiated 800H-TMP under the same irradiation conditions. Further systematic data analyses, together with some complementary experiments, will be pursued for these samples to foster peer-reviewed journal article publications.

36 MATERIALS SCIENCE↗

Role of different compatibilizing approaches on the microstructure and mechanical properties of polypropylene/talc composites

Since in a highly filled polymer, a major problem arises from non-uniformity of properties due to the poor dispersion of filler, the application of coupling agents have been directed to overcome this problem and also to enhance the mechanical performance of the composites by improving the adhesion at the interface. In this study, a comparison between two major coupling approaches is conducted: 1) Using PPgMA as a kind of compatibilizer which changes the nature of the matrix, 2) Using titanate coupling agent which takes action at the interface and reacts with hydroxyl groups at the inorganic filler surface, resulting in the formation of monomolecular layer on the inorganic surface to increase compatibility of filler/matrix interface. The comparison is made based on the mechanical properties of the composites by means of elastic modulus, yield stress, impact strength and percentage of strain-to-fracture and evaluation of their effects on both the dispersion and adhesion of talc plates in the matrix through the microscopy. Transmission optical microscopy (TOM) and scanning electron microscopy (SEM) are used to observe the deformation micromechanism and the fracture surface of the composites, respectively.

36 MATERIALS SCIENCE↗

Microstructures and photocatalytic properties of Ag{sup +} and La{sup 3+} surface codoped TiO{sub 2} films prepared by sol-gel method

Ag{sup +} and La{sup 3+} surface codoped TiO{sub 2} films were successfully prepared by the improved sol-gel and doping processes. The as-prepared specimens were characterized using differential thermal analysis-thermogravimetry (DTA-TG), X-ray diffraction (XRD), high-resolution field emission scanning electron microscopy (FE-SEM), X-ray energy dispersive spectroscopy (EDS), Brunauer-Emmett-Teller (BET) surface area, Photoluminescence spectrum (PL) and UV-vis diffuse reflectance spectroscopy. The photocatalytic activities of the films were evaluated by degradation of an organic dye in aqueous solution. The results of XRD, FE-SEM and BET analyses indicated that the TiO{sub 2} films were composed of nano-particles or aggregates with a size of less than 10 nm. With the codoping of Ag{sup +} and La{sup 3+}, TiO{sub 2} films with high photocatalytic activity and clearly responsive to the visible light were obtained. The improvement mechanism by ions doping was also discussed. - Graphical Abstract: The PL intensity of Ag{sup +} and La{sup 3+} surface codoped TiO{sub 2} was the lowest among all samples, indicating the recombination of electron and hole was effectively prohibited compared with pure TiO{sub 2}, Ag{sup +} and La{sup 3+} bulk codoped TiO{sub 2}. Highlights: > Ag{sup +} and La{sup 3+} codoping can reduce the crystal size of TiO{sub 2}. > Ag{sup +} and La{sup 3+} surface codoped TiO{sub 2} films have an obvious optical response red-shift. > Ag{sup +} and La{sup 3+} surface codoped TiO{sub 2} films can exhibit excellent photocatalytic activity under both UV and visible light irradiations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The change of microstructure and thermal properties in ion irradiated carbon nanotube mats as a function of ion penetration depth

A stack of three carbon nanotube (CNT) mats was irradiated with 3 MeV He ions. The change in structural and thermal properties of individual mats as a function of ion penetration depth was characterized using electron microscopy and laser flash techniques. Ion irradiation can enhance thermal conductivity of the mats by introducing inter-tube displacements, which improve phonon transport across adjacent nanotubes. The enhancement, however, is reduced at higher damage levels due to the increasing phonon-defect scattering within the tubes. This study demonstrates the feasibility of using ion irradiation to manipulate thermal transport in carbon nanotubes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructure and mechanical properties of vanadium alloys after thermomechanical treatments

The results of investigation of dispersion strengthening effect on parameters of structural-phase states and characteristics of short-term strength and ductility of vanadium alloys of V–4Ti–4Cr, V–2.4Zr–0.25C, V–1.2Zr–8.8Cr and V–1.7Zr–4.2Cr–7.6W systems with different concentration of interstitial elements after optimized thermomechanical treatment mode were summarized. It was shown that for effective realization of dispersion strengthening by Orowan-type mechanism at least 25–50% of the initial volume fraction of coarse particles should be transformed into fine-disperse state and redistributed over the volume of material.

36 MATERIALS SCIENCE↗

Microstructural and electrical properties of PVA/PVP polymer blend films doped with cupric sulphate

A series of polyvinyl alcohol (PVA)/polyvinyl pyrrolidone (PVP) polymer blends added with different concentrations of cupric sulphate (CuSO{sub 4}) were prepared by solution casting method and were subjected to X-ray diffraction (XRD) and Ac conductance measurements. An attempt has been made to study the changes in crystal imperfection parameters in PVA/PVP blend films with the increase in concentration of CuSO{sub 4}. Results show that decrease in micro crystalline parameter values is accompanied with increase in the amorphous content in the film which is the reason for film to have more flexibility, biodegradability and good ionic conductivity. AC conductance measurements in these films show that the conductivity increases as the concentration of CuSO{sub 4} increases. These films were suitable for electro chemical applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Characterization of paste microstructure for durability properties of concrete

In this study, paste samples from different cementitious systems were characterized by using X-Ray Micro Computed Tomography (µ-CT) and Fluorescence Microscopy techniques. Quantitative and qualitative aspects of defects from paste samples were investigated to develop indicators of durability related properties of corresponding concrete samples. In the first phase of this study, hour glass shaped 3D printed molds were used to investigate five cementitious combinations consisting of three cement types (Coarse Ground portland cement, Type IL Portland Limestone Cement and Type I/II ordinary portland cement) and fly ash as a supplementary cementitious material. In the second phase, metal molds were used to compare the results of Coarse Ground portland cement with Type I ordinary portland cement, 5% of which was replaced with colloidal nanosilica. Potential correlations between paste and concrete have been presented. This work was supported by US Department of Energy and North Dakota Department of Commerce.

36 MATERIALS SCIENCE↗

The influence of Cd doping on the microstructure and optical properties of nanocrystalline copper ferrite thin films

Highlights: ► The structural and optical properties of Cu{sub 1−x}Cd{sub x}Fe{sub 2}O{sub 4} thin films were studied. ► The micro structural parameters of the films have been determined. ► The room temperature reflectance and transmittance data are analyzed. ► The refractive index and energy gap are determined. ► The single oscillator parameters were calculated. - Abstract: Nanocrystalline thin films of mixed Cu–Cd ferrites, Cu{sub 1−x}Cd{sub x}Fe{sub 2}O{sub 4} (x = 0, 0.2, 0.3, 0.5, 0.7, 0.8, 0.9 and 1), were deposited by electron beam evaporation technique. The films were annealed at 450 °C for 1 h. The effect of Cd doping on the structural and optical properties of the deposited films has been investigated by using X-ray diffraction (XRD) and optical spectrophotometry. XRD patterns of the annealed films show spinal cubic structure. The lattice parameter was found to increase with the increase of cadmium concentration. The crystallite size of the films was found to vary from 8 nm to 30 nm. The optical transition was found to be direct and indirect transitions with energy gaps decrease from 2.466 (x = 0) to 2.00 (x = 1) eV and from 2.148 (x = 0) to 1.824 (x = 1) eV, respectively. The refractive index dispersion of the films was found to increase with Cd content and discussed in terms of the Wemple–DiDomenico single oscillator model.

36 MATERIALS SCIENCE↗

The effect of Si on the microstructure and mechanical properties of spark plasma sintered boron carbide

Highlights: • Si addition leads to a dense final product at a low sintering temperature. • The added Si preferentially formed SiC and borosilicate glass instead of replacing the chain atoms in boron carbide. • The hardness of our Si-containing boron carbide is 30–35% greater than currently in-use commercial boron carbide plates. - Abstract: Fully dense boron carbide discs were achieved by spark plasma sintering boron carbide powders with 10 wt% silicon. The silicon did not diffuse into boron carbide grains to produce a solid solution of Si-doped boron carbide; instead the silicon reacted with impurities in the starting powder to form β-SiC and borosilicate glass. The resultant new phases facilitated densification of the multiphase ceramic through liquid phase-assisted sintering. The resultant material exhibits improved hardness (34.3 GPa Vikers hardness under 1 kg load) with toughness comparable to both Si-free and commercially available boron carbide.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of V–4Ti–4Cr alloy as a function of the chemical heat treatment regimes

The regularities of the formation of a heterophase structure and mechanical properties of V–4Ti–4Cr alloy as a function of thermomechanical and chemical heat treatments are studied. The regimes of thermomechanical treatment which provide the formation of a heterophase structure with a homogeneous volume distribution of oxycarbonitride nanoparticles with a size of about 10 nm and an increase in the volume content and thermal stability of this phase and which provide an increase in the temperature of alloy recrystallization are developed. The formation of the heterophase structure results in a substantial (up to 70%) increase in the short-term high-temperature strength of the alloy at T = 800°C. The increase in the strength is achieved while keeping a rather high level of plasticity.

36 MATERIALS SCIENCE↗

Microstructure, texture, and mechanical properties of friction stir welded commercial brass alloy

Microstructural evolution during friction stir welding of single-phase brass and corresponding mechanical properties were investigated. For this purpose, 2 mm thick brass plate was friction stir welded at a rotational speed of 450 rpm and traverse speed of 100 mm/min. The microstructure of the joint was studied using optical microscopy, scanning electron microscopy equipped with electron back scattered diffraction system, and scanning transmission electron microscopy. The mechanical properties were measured using hardness and tensile tests. The formation of subgrains and their transformation into new grains in conjunction with existence of A{sub 1}{sup ⁎}, A{sub 2}{sup ⁎} and C texture components revealed that the continuous dynamic recrystallization plays a dominant role in the microstructural evolution. However, grain boundary bulging, along with the formation of twin boundaries, and presence of the G texture component showed that the discontinues dynamic recrystallization may participate in the new grain formation. Furthermore, the different strengthening mechanisms, which caused the higher strength of the joint, were discussed. - Highlights: •Microstructural evolution during FSW of a single phase brass was investigated. •CDRX and DDRX were the main mechanisms of the grain structure formation during FSW. •GDRX and SRX were not contributed in grain structure formation. •The lamellas TBs were formed in the SZ of the joints. •Grain boundary, dislocation, and texture effects resulted in higher strength.

36 MATERIALS SCIENCE↗

Effect of rare-earth composition on microstructure and pinning properties of Zr-doped (Gd, Y)Ba{sub 2}Cu{sub 3}O{subx} superconducting tapes.

The effect of changing Gd + Y content from 1.2 to 1.6 in the precursor of (Gd,Y)Ba{sub 2}Cu{sub 3}O{sub 7} superconducting thin film tapes made by metal organic chemical vapor deposition (MOCVD) at a constant Gd:Y ratio and a fixed Zr content of 7.5% has been studied. The influence of changing the Gd:Y ratio from Gd = 0 to Y= 0 in 0.2 mol steps at a constant Gd + Y content of 1.2 in the precursor has also been investigated at a fixed Zr content of 7.5%. The critical current of these films is found to vary significantly as a function of rare-earth content as well as a function of rare-earth type. Even for a fixed Zr content, it is found that the critical current in the orientation of magnetic field parallel to the a-b plane and that in the orientation of field perpendicular to the a-b plane can be systematically varied with changing Gd + Y content as well as with changing Gd:Y ratio. The nanoscale defect structures along the a-b plane and along the c-axis are found to be sensitive to these changes in rare-earth content and type.

36 MATERIALS SCIENCE↗

Reel-to-Reel Heat Treatment, Microstructure, and Superconducting Properties of Jelly-Roll Nb{sub 3}Al Superconducting Wire

In this work, we utilized the jelly-roll method to make a single-filament Nb{sub 3}Al precursor long wire, combining with a homemade reel-to-reel rapid heating and quenching (RHQ) equipment, and consequently the high-performance Nb{sub 3}Al superconducting wires had been prepared. By investigating the heating current and wire moving speed, the optimized RHQ heat treatment conditions of this Nb{sub 3}Al wire were obtained. The results suggest that the T{sub c} for the Nb{sub 3}Al superconducting wire is up to 17.4 K and the non-Cu critical current density (non-Cu J{sub c}) reaches 1238 A/mm{sup 2} at 4.2 K and 12 T, which indicates the bcc-phase Nb–Al supersaturated solid solution has already been generated. Considering the Nb{sub 3}Al precursor wire with a large thickness of Al layer, about 690 nm, such high J{sub c} is quite unexpected. The SEM analysis presents that there is still some unreacted Nb and Nb{sub 2}Al phase in the superconducting wire, which may result from the inhomogeneity of Nb and Al foils. This work implies the Nb{sub 3}Al superconducting wire is promising to the application of high-field superconducting magnets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗