Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material Point Method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Structural and Dynamical Insights into the Formation Process of a Cross-Linked Polymer Network in Acrylic Adhesives During Thermal Curing

Many modern adhesives, sealants, and coatings rely on the controlled transition from a liquid to a solid state by forming a three-dimensional cross-linked polymer network, often referred to as curing. The curing process, which is initiated by the mixing of reactive components or an external trigger, defines the structure of a network and further controls the final mechanical properties of cured materials. However, the curing mechanism is not fully understood yet due to the lack of experimental tools capable of directly probing the structure and dynamics of a network over relevant time- and length scales. Here, in this paper, we report the curing process of a commercial two-component methyl methacrylate (MMA) adhesive using in operando X-ray photon correlation spectroscopy (XPCS), a method that closely simulates the target manufacturing environment of the adhesive. The results are then integrated with those obtained by rheology, differential scanning calorimetry (DSC), and transmission electron microscopy to establish the structure–dynamics–process–property relationship. The XPCS results identify four distinct stages in the curing process after the mixing, extrusion, and deposition of the acrylic adhesive: (i) At a cure time (or “aging time”, t age ) of less than 1 min, nanodomains of polymerized MMA are formed within a liquid monomeric MMA matrix. The average size is several nm and remains constant over t age , while the dynamics of the nanodomains are slowed down with t age due to an increase in the viscosity of the MMA matrix. (ii) After t age > 1 min, the size of the nanodomains increases with t age until the gel point (= 6.3 min after mixing as determined by rheology). The dynamics of the nanodomains also increase due to the heat generated by the exothermic reaction. (iii) At the gel point, the nanodomains begin to interconnect each other, resulting in a network structure with a characteristic length of about 100 nm. This characteristic network size does not change for the rest of the curing process up to t age = 500 min. The dynamics of the network structure, however, show a rapid slowing down with t age up to t age ≈ 12 min, corresponding to the onset of vitrification (as determined by rheology). (iv) At t age > 12 min, when the DSC and rheology data can no longer provide meaningful information, the XPCS data show a further slowing down of the network dynamics associated with vitrification. Our results provide rich and complex insights into the physics and material design of thermosets in commercially relevant processes, which are essential for future industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Framework for Inverse Prediction Using Functional Response Data

Inverse prediction models have commonly been developed to handle scalar data from physical experiments. However, it is not uncommon for data to be collected in functional form. When data are collected in functional form, it must be aggregated to fit the form of traditional methods, which often results in a loss of information. For expensive experiments, this loss of information can be costly. In this study, we introduce the functional inverse prediction (FIP) framework, a general approach which uses the full information in functional response data to provide inverse predictions with probabilistic prediction uncertainties obtained with the bootstrap. The FIP framework is a general methodology that can be modified by practitioners to accommodate many different applications and types of data. We demonstrate the framework, highlighting points of flexibility, with a simulation example and applications to weather data and to nuclear forensics. Results show how functional models can improve the accuracy and precision of predictions.

42 ENGINEERING↗
DOE OSTI2022

Transition metal impurities in silicon: computational search for a semiconductor qubit

Abstract Semiconductors offer a promising platform for physical implementation of qubits, but their broad adoption is presently hindered by limited scalability and/or very low operating temperatures. Learning from the nitrogen-vacancy centers in diamond, our goal is to find equivalent optically active point defect centers in crystalline silicon, which could be advantageous for their scalability and integration with classical devices. Transition metal (TM) impurities in silicon are common paramagnetic deep defects, but a comprehensive theoretical study of the whole 3 d series that considers generalized Koopmans’ condition is missing. We apply the HSE06(+U) method to examine their potential as optically active spin qubits and identify seven TM impurities that have optically allowed triplet–triplet transitions within the silicon band gap. These results provide the first step toward silicon-based qubits with higher operating temperatures for quantum sensing. Additionally, these point defects could lead to spin-photon interfaces in silicon-based qubits and devices for mid-infrared free-space communications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Selective modulation of electronic transport in VO 2 induced by 10 keV helium ion irradiation

Vanadium dioxide (VO 2 ) manifests an abrupt metal–insulator transition (MIT) from monoclinic to rutile phases, with potential use for tunable electronic and optical properties and spiking neuromorphic devices. Understanding pathways to modulate electronic transport in VO 2 , as well as its response to irradiation (e.g., for space applications), is critical to better enable these applications. In this work, we investigate the selective modulation of electronic transport in VO 2 films subject to different 10 keV helium ion (He + ) fluences. Under these conditions, the resistivity in the individual monoclinic and rutile phases varied by 50%–200%, while the MIT transformation temperature remains constant within 4 °C independent of irradiation fluence. Importantly, different trends in the resistivity of the monoclinic and rutile phases were observed both as a function of total He fluence as well as in films grown on different substrates (amorphous SiO 2 /Si vs single crystal Al 2 O 3 ). Through a combination of measurements including majority carrier sign via Seebeck, low frequency noise, and TEM, our investigation supports the presence of different kinds of point defects (V in; O in), which may arise due to grain boundary defect interactions. Our work suggests the utility of He irradiation for the selective modulation of VO 2 transport properties for neuromorphic, in contrast to other established but non-selective methods, like doping.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Crack problems in cylindrical and spherical shells

Standard plate or shell theories were used as a starting point to study the fracture problems in thin-walled cylindrical and spherical shells, assuming that the plane of the crack is perpendicular to the surface of the sheet. Since recent studies have shown that local shell curvatures may have a rather considerable effect on the stress intensity factor, the crack problem was considered in conjunction with a shell rather than a plate theory. The material was assumed to be isotropic and homogeneous, so that approximate solutions may be obtained by approximating the local shell crack geometry with an ideal shell which has a solution, namely a spherical shell with a meridional crack, a cylindrical shell with a circumferential crack, or a cylindrical shell with an axial crack. A method of solution for the specially orthotropic shells containing a crack was described; symmetric and skew-symmetric problems are considered in cylindrical shells with an axial crack.

Erdogan, F.↗
NASA NTRS2003

Infrared Spectroscopy as a Chemical Fingerprinting Tool

Infrared (IR) spectroscopy is a powerful analytical tool in the chemical fingerprinting of materials. Any sample material that will interact with infrared light produces a spectrum and, although normally associated with organic materials, inorganic compounds may also be infrared active. The technique is rapid, reproducible and usually non-invasive to the sample. That it is non-invasive allows for additional characterization of the original material using other analytical techniques including thermal analysis and RAMAN spectroscopic techniques. With the appropriate accessories, the technique can be used to examine samples in liquid, solid or gas phase. Both aqueous and non-aqueous free-flowing solutions can be analyzed, as can viscous liquids such as heavy oils and greases. Solid samples of varying sizes and shapes may also be examined and with the addition of microscopic IR (microspectroscopy) capabilities, minute materials such as single fibers and threads may be analyzed. With the addition of appropriate software, microspectroscopy can be used for automated discrete point or compositional surface area mapping, with the latter providing a means to record changes in the chemical composition of a material surface over a defined area. Due to the ability to characterize gaseous samples, IR spectroscopy can also be coupled with thermal processes such as thermogravimetric (TG) analyses to provide both thermal and chemical data in a single run. In this configuration, solids (or liquids) heated in a TG analyzer undergo decomposition, with the evolving gases directed into the IR spectrometer. Thus, information is provided on the thermal properties of a material and the order in which its chemical constituents are broken down during incremental heating. Specific examples of these varied applications will be cited, with data interpretation and method limitations further discussed.

Huff, Timothy L.↗
DOE OSTI2020

Semi-supervised Machine Learning Enables the Robust Detection of Multireference Character at Low Cost

Multireference (MR) diagnostics are common tools for identifying strongly correlated electronic structure that makes single-reference (SR) methods (e.g., density functional theory or DFT) insufficient for accurate property prediction. However, MR diagnostics typically require computationally demanding correlated wave function theory (WFT) calculations, and diagnostics often disagree or fail to predict MR effects on properties. To overcome these challenges, we introduce a semi-supervised machine learning (ML) approach with virtual adversarial training (VAT) of an MR classifier using 15 WFT and DFT MR diagnostics as inputs. In semi-supervised learning, only the most extreme SR or MR points are labeled, and the remaining point labels are learned. The resulting VAT model outperforms the alternatives, as quantified by the distinct property distributions of SR- and MR-classified molecules. Additionally, to reduce the cost of generating inputs to the VAT model, we leverage the VAT model’s robustness to noisy inputs by replacing WFT MR diagnostics with regression predictions in an MR decision engine workflow that preserves excellent performance. We demonstrate the transferability of our approach to larger molecules and those with distinct chemical composition from the training set. This MR decision engine demonstrates promise as a low-cost, high-accuracy approach to the automatic detection of strong correlation for predictive high-throughput screening.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Quantum-Based Approach to Predict Primary Radiation Damage in Polymeric Networks

Initial atomistic-level radiation damage in chemically reactive materials is thought to induce reaction cascades that can result in undesirable degradation of macroscale properties. Ensembles of quantum-based molecular dynamics (QMD) simulations can accurately predict these cascades, but extracting chemical insights from the many underlying trajectories is a labor-intensive process that can require substantial a priori intuition. We develop here a general and automated graph-based approach to extract all chemically distinct structures sampled in QMD simulations and apply our approach to predict primary radiation damage of polydimethylsiloxane (PDMS), the main constituent of silicones. A postprocessing protocol is developed to identify underlying polymer backbone structures as connected components in QMD trajectories. Furthermore, these backbones form a repository of radiation-damaged structures. A scheme for extracting and updating a library of isomorphically distinct structures is proposed to identify the spanning set and aid chemical interpretation of the repository. The analyses are applied to ensembles of cascade QMD simulations in which the four element types in PDMS are selectively excited in primary knock-on atom events. Our approach reveals a much higher degree of combinatorial complexity in this system than was inferred through radiolysis experiments. Probabilities are extracted for radiation-induced network changes including formation of branch points, carbon linkages, cycles, bond scissions, and carbon uptake into the Si–O siloxane backbone network. The general analysis framework presented here is readily extendable to modeling chemical degradation of other polymers and molecular materials and provides a basis for future quantum-informed multiscale modeling of radiation damage.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A strain-driven thermotropic phase boundary in BaTiO 3 at room temperature by cycling compression

In BaTiO 3 single crystals, we observed a strain-driven phase transition from the tetragonal phase to the tetragonal-orthorhombic phase boundary which can be introduced by slow cycling compressions (a loading of up to 0.5 GPa, strain rate of 10 -4 s -1 , and 100 cycles) at room temperature. Different from the well-known tetragonal to cubic phase transition under stress (~2 GPa), it only takes place locally around bent 90° domain walls. The inhomogeneous local stress and electrical fields as well as the mobile point defect pinning effect contribute to the phase re-entrance. Through comparison experiments by in situ synchrotron x-ray diffraction, Raman scattering, and (scanning) transmission electron microscopy, we explored the phase transition mechanism. Based on that, we developed a mechanical method to obtain well-stabilized high-density thermotropic phase boundary structures (with tetragonal, orthorhombic, and bridging monoclinic phases) in BaTiO 3 for potential applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermal conductivity measurement of U-Mo and U-Mo/Al interaction layers generated from in-pile irradiation using the suspended-bridge method

Here, this study presents the first measurement of the individual thermal conductivity of U-7wt.%Mo fuel particles and U-Mo/Al interaction layers (ILs) from in-pile irradiated dispersion fuel plates, using the suspended-bridge method. Nanorods of U-7wt.%Mo fuel and U-Mo/Al ILs were extracted by focused ion beam (FIB), and their microstructures were characterized with transmission electron microscopy (TEM). TEM revealed finely distributed nanobubbles in the U-7wt.%Mo matrix, along with an amorphous structure in the ILs. The thermal conductivity of in-pile irradiated U-7wt.%Mo was approximately 30% lower than that of the unirradiated material, ranging from 6.7 W/m·K at 300 K to 8.5 W/m·K at 380 K. The ILs exhibited even lower thermal conductivity, from 2.1 W/m·K at 300 K to 2.7 W/m·K at 380 K. These reductions, attributed to nanobubbles, fission products, and irradiation-induced point defects, were analyzed through a combination of microstructural characterization and literature-based transport models, which successfully reproduced the observed degradation trends.

42 - ENGINEERING↗
DOE OSTI2022

Designing silicon carbide heterostructures for quantum information science: challenges and opportunities

Abstract Silicon carbide (SiC) can be synthesized in a number of different structural forms known as polytypes with a vast array of optically active point defects of interest for quantum information sciences. The ability to control and vary the polytypes during SiC synthesis may offer a powerful methodology for the formation of new material architectures that expand our ability to manipulate these defects, including extending coherence lifetimes and enhancing room temperature operation. Polytypic control during synthesis presents a significant challenge given the extreme conditions under which SiC is typically grown and the number of factors that can influence polytype selection. In situ monitoring of the synthesis process could significantly expand our ability to formulate novel polytype structures. In this perspective, we outline the state of the art and ongoing challenges for precision synthesis in SiC. We discuss available in situ x-ray characterization methods that will be instrumental in understanding the atomic scale growth of SiC and defect formation mechanisms. We highlight optimistic use cases for SiC heterostructures that will become possible with in situ polytypic control and end by discussing extended opportunities for integration of ultrahigh quality SiC materials with other semiconductor and quantum materials.

Harmon, K. J. (ORCID:0000000164277971)↗
DOE OSTI2024

Predicting ptychography probe positions using single-shot phase retrieval neural network

Ptychography is a powerful imaging technique that is used in a variety of fields, including materials science, biology, and nanotechnology. However, the accuracy of the reconstructed ptychography image is highly dependent on the accuracy of the recorded probe positions which often contain errors. These errors are typically corrected jointly with phase retrieval through numerical optimization approaches. When the error accumulates along the scan path or when the error magnitude is large, these approaches may not converge with satisfactory result. We propose a fundamentally new approach for ptychography probe position prediction for data with large position errors, where a neural network is used to make single-shot phase retrieval on individual diffraction patterns, yielding the object image at each scan point. The pairwise offsets among these images are then found using a robust image registration method, and the results are combined to yield the complete scan path by constructing and solving a linear equation. We show that our method can achieve good position prediction accuracy for data with large and accumulating errors on the order of 10 2 pixels, a magnitude that often makes optimization-based algorithms fail to converge. For ptychography instruments without sophisticated position control equipment such as interferometers, our method is of significant practical potential.

47 OTHER INSTRUMENTATION↗
NASA NTRS2003

Evaluation of Treadmill Exercise in a Lower Body Negative Pressure Chamber as a Countermeasure for Weightlessness-Induced Bone Loss: a Bed Rest Study with Identical Twins

Counteracting bone loss is required for future space exploration. We evaluated the ability of treadmill exercise in a LBNP chamber to counteract bone loss in a 30-day bed rest study. Eight pairs of identical twins were randomly assigned to sedentary control or exercise groups. Exercise within LBNP decreased the bone resorption caused by bed rest and may provide a countermeasure for spaceflight. INTRODUCTION: Bone loss is one of the greatest physiological challenges for extended-duration space missions. The ability of exercise to counteract weightlessness-induced bone loss has been studied extensively, but to date, it has proven ineffective. We evaluated the effectiveness of a combination of two countermeasures-treadmill exercise while inside a lower body negative pressure (LBNP) chamber-on bone loss during a 30-day bed rest study. MATERIALS AND METHODS: Eight pairs of identical twins were randomized into sedentary (SED) or exercise/LBNP (EX/LBNP) groups. Blood and urine samples were collected before, several times during, and after the 30-day bed rest period. These samples were analyzed for markers of bone and calcium metabolism. Repeated measures ANOVA was used to determine statistical significance. Because identical twins were used, both time and group were treated as repeated variables. RESULTS: Markers of bone resorption were increased during bed rest in samples from sedentary subjects, including the collagen cross-links and serum and urinary calcium concentrations. For N-telopeptide and deoxypyridinoline, there were significant (p < 0.05) interactions between group (SED versus EX/LBNP) and phase of the study (sample collection point). Pyridinium cross-links were increased above pre-bed rest levels in both groups, but the EX/LBNP group had a smaller increase than the SED group. Markers of bone formation were unchanged by bed rest in both groups. CONCLUSIONS: These data show that this weight-bearing exercise combined with LBNP ameliorates some of the negative effects of simulated weightlessness on bone metabolism. This protocol may pave the way to counteracting bone loss during spaceflight and may provide valuable information about normal and abnormal bone physiology here on Earth.

Twin Study↗
DOE OSTI2022

Data Mining and Visualization of High-Dimensional ICME Data for Additive Manufacturing

Integrated computational materials engineering (ICME) methods combining CALPHAD with process-based simulations can produce rich, high-dimensional data for alloy and process design. In ICME methods for metallurgical applications, the visualization and interpretation of such high-dimensional data has previously been through heat maps represented in 2 or 3 dimensions. While such an approach is ideal when one variable is varied at a time, in the case of high-dimensional data with multiple variables varied simultaneously, as is the case in additive manufacturing, interpreting the trends through two- or three-dimensional heat maps becomes challenging. Here, we propose a strategy of mixed visual data mining and quantitative analysis for high-dimensional metallurgical and process data using high-throughput thermodynamic calculations. Two case studies show the application of the proposed approach. The first case study investigated the effects of feedstock chemistry on the δ ferrite formation in 316L stainless steel powders used for binder jet additive manufacturing. The second case study linked Scheil–Gulliver calculations to a process model for dissimilar joining of aluminum alloys 5356 and 6111 during laser hot-wire additive manufacturing. Both cases contained thousands of calculated data points, showcasing the utility of visual data analysis through parallel coordinate plotting, Pearson correlation coefficient matrices, and scatter matrices compared to traditional process maps. These visualization techniques can be extended to many additive manufacturing problems to capture process–structure–property relationships for additively manufactured components.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Interlaboratory Reproducibility of Contour Method Data in a High Strength Aluminum Alloy

The contour method for residual stress measurement has seen significant development, but an experimental reproducibility study utilizing physical samples has not been published. A double-blind reproducibly study is reported, having scope beginning with EDM cutting and ending with residual stress calculation. A reinforced I-beam sample geometry is identified for its unique residual stress profile when extracted from residual stress bearing quenched aluminum bar (7050-T74). Contour measurements are prescribed on a midplane of symmetry with dimensions 24.0 mm by 50.0 mm. Fourteen identically prepared samples are fabricated from a single long bar with well characterized and uniform residual stress. Five samples throughout the bar are identified for planning measurements to validate sample uniformity and overall suitability of the residual stress field. The planning measurements employ a range of techniques: contour method, neutron diffraction, and hole-drilling. Eight samples are distributed to an international group of participants to execute their standard measurement practice. A double-blind process is followed to provide anonymity. Results are provided by eight participants: six being self-similar and two being quite different, the latter set aside as outliers. An average residual stress field is established from non-outlying results and the spatial distribution of reproducibility standard deviation is determined. The average stress field ranges from -60 to 70 MPa and the reproducibility standard deviation averages 8.1 MPa on the measurement plane. The average reproducibility standard deviation is about 3 × larger for points within 1.0 mm of plane boundaries (17.6 MPa) than for the remaining points (6.1 MPa). Reproducibility standard deviation (among different labs) for contour method residual stress measurement is found to be very similar to repeatability standard deviation (in a single lab) reported in prior work. The reproducibility observed here, for the entire measurement process, is also similar to that found in a prior reproducibility study limited to contour method data analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Synthesis of bulk reactive Ni–Al composites using high pressure torsion

Self-propagating exothermic reactions, for instance in the nickel-aluminum (Ni-Al) system, have been widely studied to create high performance intermetallic compounds or for in-situ welding. Their easy ignition once the phase spacing is reduced below the micron scale, makes top-down methods like high-energy ball milling, ideal to fabricate such reactive nanostructures. A major drawback of ball milling is the need of a sintering step to form bulk pieces of the reactive material. However, this is not possible, as the targeted reactions would already proceed. Therefore, we investigate the ability of high pressure torsion as an alternative process, capable to produce bulk nanocomposites from powder mixtures. Severe straining of powder mixtures with a composition of 50 wt% Ni and 50 wt% Al enables fabrication of self-reactive bulk samples with microstructures similar to those obtained from ball milling or magnetron sputtering. Additionally, samples deformed at ambient temperature are highly reactive and can be ignited significantly below the Al melting point, finally predominantly consisting of Al 3 Ni 2 and Al 3 Ni, independent of the applied strain. Although the reaction proceeds first at the edge of the disk, the strain gradient present in the disks does not prevent reaction of the whole sample.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Cracked Gridline Wear Out Follows a Power Law

Cracks can form in Silicon solar cells in photovoltaic modules due to mechanical stresses arising from various extrinsic factors like handling and weather. While the immediate performance degradation may be minor, continuous loading overtime will degrade module performance. One probable reason is gridline surface wear across the cracked silicon with increased cyclic loading. In this work we propose a method to correlate gridline wear to module electrical degradation. We begin by conducting cyclic four-point bending tests on laminated silicon solar cells with a single crack and 22 intact gridlines for 10,000 cycles. We measure the progressive change in resistance during each loading cycle. We correlate it to a length scale called critical crack opening displacement (CCOD) that signifies failure of individual gridlines. By employing Weibull analysis, we determine the characteristic CCOD for all cycles and fit this data to a modified version of a wear power law. We observe that this i ts the data well. We also propose to study the effect of individual parameters in the power law equation and extend the equation to include material properties.

bending↗
DOE OSTI2023

Disentangling Electronic Transport and Hysteresis at Individual Grain Boundaries in Hybrid Perovskites via Automated Scanning Probe Microscopy

Underlying the rapidly increasing photovoltaic efficiency and stability of metal halide perovskites (MHPs) is the advancement in the understanding of the microstructure of polycrystalline MHP thin film. Over the past decade, intense efforts have been aimed at understanding the effect of microstructures on MHP properties, including chemical heterogeneity, strain disorder, phase impurity, etc. It has been found that grain and grain boundary (GB) are tightly related to lots of microscale and nanoscale behavior in MHP thin films. Atomic force microscopy (AFM) is widely used to observe grain and boundary structures in topography and subsequently to study the correlative surface potential and conductivity of these structures. For now, most AFM measurements have been performed in imaging mode to study the static behavior; in contrast, AFM spectroscopy mode allows us to investigate the dynamic behavior of materials, e.g., conductivity under sweeping voltage. However, a major limitation of AFM spectroscopy measurements is that they require manual operation by human operators, and as such only limited data can be obtained, hindering systematic investigations of these microstructures. Here, we designed a workflow combining the conductive AFM measurement with a machine learning (ML) algorithm to systematically investigate grain boundaries in MHPs. The trained ML model can extract GBs locations from the topography image, and the workflow drives the AFM probe to each GB location to perform a current–voltage (IV) curve automatically. Then, we are able to have IV curves at all GB locations, allowing us to systematically understand the property of GBs. Using this method, we discovered that the GB junction points are less conductive, potentially more photoactive, and can play critical roles in MHP stability, while most previous works only focused on the difference between GB and grains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗